Evo Affinity 30Ge Quick start guide

the natural way to cook
®
®
OWNER & INSTALLATION MANUAL
Affinity 30Ge
Cooktop
Evo, Inc. | 8140 SW Nimbus Ave., Bldg 5 | Beaverton, Oregon 97008 USA
Evo Affinity 30Ge
Electronically-Controlled Gas Cooktop
For Indoor Use Only
Certification: ANSI Z83.11b-2009/CSA 1.8B-2009. OMNI Report # 0141GM004S
Part #: Commercial models: 10-0050-NG | 10-0050-LP
Residential models: 10-0051-NG | 10-0051-LP
Doc: OM-C&R-30Ge 01/2016
Copyright © 2016
This appliance and its individual shutoff valve must be
disconnected from the gas supply piping system during
any pressure testing of system at test pressures in
excess of 1/2 PSI (3.5kPa).
This appliance must be isolated from the gas supply
piping system by closing its individual manual shutoff
valve during any pressures testing of the gas supply
system at test pressures equal to or less than 1/2 PSI
(3.5kPa).
This appliance, when installed, must be electrically grounded in accordance with local codes,
or in the absence of local codes, with the National Electrical Code, ANSI/NFPA70,
or the Canadian Electrical Code, CSA C22.2, as applicable.
Cleaning Instructions
evoamerica.com
FINAL QR Code for Evo Cleaning.indd 1 11/19/2015 11:43:18 AM

INSTALLATION INSTRUCTIONS
Affinity 30Ge
Evo, Inc. | 8140 SW Nimbus Ave., Bldg 5 | Beaverton, Oregon 97008 USA
Grill is for indoor use only. Grill should be operated in a well-ventilated space. Never operate near
flammableliquidsorvapors.Donotinstallorusegrillwithin36”ofcombustiblematerialsfrombackand
sidesofgrill.Grillshallnotbelocatedunderunprotectedoverheadmadeofcombustibleconstruction.
Warnings
FOR YOUR SAFETY
If You Smell Gas:
1. Shut off gas to appliance.
2. Extinguish any open flame.
3. Remove grill cooking surface.
4. If odor continues, immediately call your
gas supplier or your fire department.
5. Evacuate all personnel from the area.
FOR YOUR SAFETY
1. Do not store or use gasoline or other
flammable vapors and liquids under
this appliance or in the vicinity of this
or any other appliance.
2. An LP Tank not connected for use shall
not be stored in the vicinity of this or
any other appliance.
Improperinstallation, adjustment, alteration, service or maintenance can cause property damage,
injury or death. Read the installation, operating and maintenance instructions thoroughly before
installing or servicing this equipment.
If you suspect a natural gas leak or other gas emergency and are unsure of its severity or what
to do, evacuate the area immediately and call 911 from a safe location.
POST THIS WARNING MESSAGE IN A PROMINENT LOCATION
Do not block or obstruct air ventilation for combustion.
WARNING
WARNING
This symbol identifies the most important
safety messaging in this manual. When you
see this symbol, be alert to the possibility of
serious bodily injury if the instructions are not
followed. Be sure to read and carefully follow
all of the messages.
It is the responsibility of the assembler/owner to
assemble, install and maintain gas grill. Do not
letchildren operateorplay nearyourgrill. Failure
tofollow theseinstructionscould resultinserious
personal injury and / or property damage.
WARNING
Do not attempt to light appliance during a power outage.
WARNING
WARNING

INSTALLATION INSTRUCTIONS
Affinity 30Ge
Evo, Inc. | 8140 SW Nimbus Ave., Bldg 5 | Beaverton, Oregon 97008 USA
2
THIS MANUAL MUST BE RETAINED FOR FUTURE REFERENCE. READ, UNDERSTAND,
AND FOLLOW THE INSTRUCTIONS AND WARNINGS CONTAINED IN THIS MANUAL.
DANGER POTENTIALLY HAZARDOUS SITUATION WHICH, IF NOT
AVOIDED, COULD RESULT IN DEATH
HIGH
VOLTAGE
CAUTION POTENTIALLYHAZARDOUS SITUATIONWHICH, IF NOTAVOIDED,
MAY RESULT IN MINOR OR MODERATE INJURY.
WARNING POTENTIALLYHAZARDOUS SITUATION WHICH,IF NOTAVOIDED,
COULD RESULT IN DEATH OR SERIOUS INJURY
CAUTION Helpful tips and technique instructions are shown.
Notes
Complete Now For Future Reference
Model #_______________________________ Serial # _________________________________
Date Purchased ________________________ Location Purchased _______________________
Date Installed __________________________ Location Installed _________________________
The installation of this cooking equipment must conform with local codes, or in the
absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54, or the
Natural Gas and Propane Installation Code, CSA B149.1, as applicable.
To Installer or Person Uncrating Grill:
Leave these instructions with purchaser.
To Purchaser:
Keep these instructions for future reference.

INSTALLATION INSTRUCTIONS
Affinity 30Ge
Evo, Inc. | 8140 SW Nimbus Ave., Bldg 5 | Beaverton, Oregon 97008 USA
3
READ FIRST
IMPORTANT PRODUCT AND SAFETY INFORMATION
WARNING INSTALLATION OF THIS UNIT MUST BE DONE BY A QUALIFIED PLUMBER
AND ELECTRICIAN. INCORRECT INSTALLATION CAN CAUSE INJURY
TO PERSONNEL AND/OR DAMAGE TO EQUIPMENT. THIS UNIT MUST BE
INSTALLED IN ACCORDANCE WITH ALL LOCAL AND UNIFORM BUILDING/
CONSTRUCTION CODES.
WARNING DO NOT INSTALL THIS UNIT TO COMBUSTIBLE SURFACES, AND DO
NOT USE COMBUSTIBLE MATERIALS IN THE CONSTRUCTION OF ANY
COUNTER, STAND, OR OTHER DEVICE.
WARNING THIS UNIT IS EQUIPPED WITH A THREE-PRONG (GROUNDING) PLUG FOR
YOUR PROTECTION AGAINST SHOCK HAZARD AND MUST BE PLUGGED
INTO GROUNDED RECEPTACLE. DO NOT MODIFY, CUT, OR REMOVE THE
GROUNDING PRONG FROM THIS PLUG.
WARNING IMMEDIATELY AFTER CONNECTING GAS SUPPLY LINE AND BEFORE
FIRST IGNITION, CHECK ALL GAS CONNECTIONS WITH SOAPY WATER
TO TEST FOR LEAKS.
WARNING KEEP WATER AND ALL COOKING SPILL OVERS AWAY FROM FRONT
CONTROL PANEL AND ALL OPEN SERVICE AREAS. NEVER HOSE UNIT,
OR SPRAY UNIT WITH CLEANING SOLUTIONS.
CAUTION CAREFULLY FOLLOW ALL INSTALLATION INSTRUCTIONS AND
CONSTRUCT ALL COUNTER SPACE, STANDS, OR OTHER SURFACES TO
THE RECOMMENDED INSTALLATION SPECIFICATIONS AS OUTLINED IN
THIS MANUAL.
CAUTION THIS UNIT IS HEAVY AND SHOULD BE INSTALLED BY TWO PEOPLE.
USE NECESSARY BLOCKING FOR LOCATING COOK SURFACE AND
CONNECTING TEMPERATURE SENSORS TO THE UNDERSIDE OF COOK
SURFACE.
CAUTION ALWAYS KEEP ANY AND ALL FLAMMABLE LIQUIDS AND COMBUSTIBLE
MATERIALS AWAY FROM UNIT. DO NOT STORE TOWELS OR UTENSILS,
OR ANY OTHER ITEMS ON UNIT’S DRIP PAN.
CAUTION DO NOT CLEAN THE COOK SURFACE WITH GRILL BRICKS OR CLEANING
SOLUTIONS. USE ONLY GRILL SCREENS AND GRILL PADS AND FOLLOW
THE PRESCRIBED METHOD OF CLEANING AS OUTLINED IN THIS
MANUAL.
NOTICE THE SERIAL NUMBER AND MODEL INFORMATION LABEL PLATE IS
LOCATED UNDERNEATH THE CONTROL PANEL.
NOTICE INSTALLATION OF ANY VENT HOODS OR FIRE EXTINGUISHER SYSTEMS
MUST CONFORM TO THE NATIONAL, STATE, AND LOCAL BUILDING AND
ALL APPLICABLE UNIFORM CONSTRUCTION CODES.
NOTICE DURING THE FIRST FEW HOURS OF OPERATION IT IS NORMAL FOR OILS
USED IN THE MANUFACTURING PROCESS TO BURN OFF AND GIVE AN
ODOR OR PETROLEUM SMOKE.

INSTALLATION INSTRUCTIONS
Affinity 30Ge
Evo, Inc. | 8140 SW Nimbus Ave., Bldg 5 | Beaverton, Oregon 97008 USA
Evo, Incorporated warrants to the original residential consumer-purchaser that the Evo grill shall be free from rust-through on all
metal surfaces and shall be free from defects in materials and workmanship under normal and reasonable use from the original
date of purchase. Evo promises to replace, at its determination, any product or component that is defective and covered under
this warranty for as long as you, the registered original consumer-purchaser, owns the grill. This is your sole and exclusive
remedy. This warranty is for the benefit of the original consumer-purchaser and is non-transferable. This warranty is subject to the
limitations, exclusions and other provisions listed below.
Limitations Involving Materials and Components:
Warranty does not apply to normal wear and tear, which are expected over the course of ownership. The materials and
components listed below are covered according to the following schedule from the original date of purchase:
• One Year – electrical and electronic components [including, but not limited to, electronic displays, overlay and membrane
switches, temperature sensors (RTD and K-Value Thermal Couple), hot surface igniters, computers, transformers,
heater elements, relays, igniters, ignition controllers, wiring, switches, encoders, outlets and plugs
• One Year – gas components [including, but not limited to, gas regulator, gas hoses, manifold assemblies]
• One Year – accessories and repair parts
The Warranty Registration Card (or online warranty registration form available at www.evoamerica.com/content/
residential-warranty-registration) must be completed and returned/submitted to Evo, Incorporated within 30 days from the
date of purchase. The original purchase invoice or payment record must be retained and produced upon request if claims
are made under this warranty. To receive a replacement Warranty Registration Card, write or call the address listed at the
bottom of this page. Warranties are void if the original serial numbers have been removed, altered, or cannot be readily
determined.
THIS WARRANTY APPLIES ONLY TO PRODUCTS PURCHASED AND LOCATED WITHIN THE UNITED STATES
OR CANADA.
WHAT IS NOT COVERED BY THIS WARRANTY
1. Conditions and damages resulting from any of the following:
a. Improper or inadequate installation, delivery, use, storage or maintenance
b. Any repair not authorized in writing by Evo, Inc., any modifications, misapplications, or unreasonable use
c. Improper setting of any control
d. Harsh environmental conditions, including, but not limited to, continual seawater spray, high pressure water, and direct contact
with corrosive chemicals and materials
e. Excessive or inadequate electrical, or gas supply
f. Accidents, natural disasters, acts of God
g. Conditions covered by the purchaser’s insurance
h. Cleaning supplies and filters
2. Products purchased or utilized for commercial use without the express authorization of Evo, Incorporated for such use
3. Labor not pre-authorized by Evo, Incorporated, and labor not performed by an authorized Evo service agency or representative
4. Pre-authorized warranty labor performed outside of normal business hours, and at overtime and premium rates
5. The cost of service or a service call to:
a. Identify or correct installation errors
b. Transport the product or component for service to/from the manufacturer or service center
c. Instruct the user of the proper use of the product
6. The cost for any inconvenience, personal injury or property damage due to failure of the product, and cost of damage arising out
of the transportation of the product which is covered under different terms with the carrier
7. Natural variations in color and finishes that are inherent to the material and unavoidable (and therefore not defects)
ALL IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY, SUITABILITY,
QUALITYAND/OR FITNESS FORAPARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE EXPRESS
WARRANTY PERIODS SPECIFIEDABOVE FOR THE PARTS DESCRIBED THEREIN. EVO, INCORPORATED
MAKES NO OTHER WARRANTYAND WILL NOT BE LIABLE FORANY DIRECT OR INDIRECT, CONSEQUENTIAL
OR INCIDENTAL DAMAGES. Some states do not allow limitations on how long an implied warranty lasts, so the above
limitation may not apply to you. Neither Evo manufacturer representatives and dealers, nor the retail establishment selling this
product has any authority to make any warranties or to promise remedies in addition to or inconsistent with those stated above.
The maximum liability to Evo, Incorporated in any event, shall not exceed the purchase price of the product paid by the original
consumer-purchaser. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.
EVO RESIDENTIAL LIMITED WARRANTY TERMS

INSTALLATION INSTRUCTIONS
Affinity 30Ge
Evo, Inc. | 8140 SW Nimbus Ave., Bldg 5 | Beaverton, Oregon 97008 USA
5
SAFETY LABEL
Evo Affinity 30Ge Cooktop
SERIAL NUMBER
N° SÉRIE
Report No. /Rapport n° 0141GM004S
Modèle commercial n°
Commercial Model # 10-0050
FOR INDOOR USE ONLY
POUR UNE UTILISATION À L'INTÉRIEUR UNIQUEMENT
Tested To / Testé pour:
ANSI Z83.11b-2009/CSA 1.8b-2009
FOOD SERVICE EQUIPMENT
CET APPAREIL EST CONÇU UNIQUEMENT POUR ÊTRE UTILISÉ AVEC DU :
THIS APPLIANCE EQUIPPED FOR USE ONLY WITH :
BTU Input Rate Max / Débit calorifique max. en BTU :
Drill Size Orifice No. / Dimensions de l'orifice n° : Outer Ring :
Anneau extérieur :
Anneau intérieur :
LP
GPL
48,000
#52
1.61mm
#55
1.32mm
NG
GN
46,000
#41
2.44mm
#48
1.93mm
Inner Ring :
Evo est protégé par des brevets É-U 6,189,530 et 6,488,022 et brevets É-U en instance.
Evo is protected under U.S Patents 6,189,530 and 6,488,022 and U.S. Patents Pending. Fabriqué aux É.-U.Made in USA.
10-0051
Modèle residential n°
Residential Model #
MANUFACTURE DATE
DATE DU CONSTRUCTEUR
ELECTRICAL VOLTAGE
ÉLECTRIQUE Le VOLTAGE
120V or/ou 220V / 50-60Hz
1-Phase, Max: 7 AMPS /
AMPÈRES
09-12-/2014
CLEARANCE TO COMBUSTIBLE CONSTRUCTION FROM CHASSIS
DÉGAGEMENT D'UNE CONSTRUCTION COMBUSTIBLE PARTIR D'UN CHÂSSIS
Back
Sides
Bottom
Combustible
Combustible Non-combustible
Incombustible
3/8”
3/8”
3”
9.53mm
9.53mm
76mm
0”
0“
3”
0mm
0mm
76mm
Min 3” clearance below unit venting to 22 sq/in of combustible air. For installation under
ventilation hood only. / Minimum 76mm de dégagement ci-dessous ventilation unité à
142 cm² dans l'air. Installer en dessous d’une hotte de ventilation seulement.
retour
côtés
bas
Manufactured By construit pres:
Evo, Inc., 8140 Nimbus Ave., Bldg 5
Beaverton, Oregon 97008 USA
CLEARANCE TO COMBUSTIBLE SURFACE FROM COOKING SURFACE
DÉGAGEMENT AUX SURFACE COMBUSTIBLE DE LA SURFACE DE CUISSON
Top
Sides
36”
12”
91cm
30cm
haut
côtés
*
*
* 3/8” cement board / 9.53mm panneau de ciment
C
LP Propane Manifold Gas Pressure = 10” W.C
NG Natural Gas Manifold Gas Pressure = 4” W.C

INSTALLATION INSTRUCTIONS
Affinity 30Ge
Evo, Inc. | 8140 SW Nimbus Ave., Bldg 5 | Beaverton, Oregon 97008 USA
6
Evo, Incorporated warrants to the original commercial foodservice purchaser that the Evo cooking, refrigeration and ventilation
equipment shall be free from rust through on all metal surfaces and shall be free from defects in materials and workmanship under
normal and reasonable use for One Year from the original date of purchase from Evo, Inc. This warranty is for the benefit of the
original use purchaser and is non-transferable. Evo promises to replace, at its determination, any product or component that is
defective during this initial one year period. Or as a resolution, Evo may at its option repurchase the product at its original purchase
price. This is your sole and exclusive remedy. This warranty is subject to the limitations, exclusions and other provisions listed
below.
Limitations Involving Materials and Components:
Warranty does not apply to normal wear and tear, which are expected over the course of ownership. The materials and
components listed below are covered according to the following schedule from the original date of purchase from Evo:
• One Year – electrical and electronic components [including, but not limited to, electronic displays, overlay and membrane
switches, temperature sensors (RTD and K-Value Thermal Couple), hot surface igniters, computers, transformers,
heater elements, relays, igniters, ignition controllers, wiring, switches, encoders, outlets and plugs
• One Year – gas components [including, but not limited to, gas regulator, gas hoses, manifold assemblies]
• One Year – accessories and repair parts
• Ninety (90) Days - refrigeration components [including, but not limited to, compressor, evaporator, pressure control units]
The Warranty Registration Card (or online warranty registration form available at www.evoamerica.com/content/
commercial-warranty-registration) must be completed and returned/submitted to Evo, Incorporated within 30 days from
the date of purchase. The original purchase invoice or payment record must be retained and produced upon request if
claims are made under this warranty. To receive a replacement Warranty Registration Card, write or call the address listed
at the bottom of this page. Warranties are void if the original serial numbers have been removed, altered, or cannot be
readily determined.
THIS WARRANTY APPLIES ONLY TO PRODUCTS PURCHASED AND LOCATED WITHIN THE USA OR CANADA.
What is NOT COVERED by this warranty:
1. Conditions and damages resulting from any of the following:
a. Improper or inadequate installation, delivery, use, storage or maintenance
b. Any repair not authorized in writing by Evo, Inc., any modifications, misapplications, or unreasonable use
c. Improper setting of any control
d. Harsh environmental conditions, including, but not limited to, continual seawater spray, high pressure water, and direct contact
with corrosive chemicals and materials
e. Excessive or inadequate electrical, gas, or refrigeration supply
f. Accidents, natural disasters, acts of God
g. Conditions covered by the purchaser’s insurance
h. Cleaning supplies and filters
2. Labor not pre-authorized by Evo, Incorporated, and labor not performed by an authorized Evo service agency or
representative
3. Pre-authorized warranty labor performed outside of normal business hours, and at overtime and premium rates
4. The cost of service or a service call to:
a. Identify or correct installation errors
b. Transport the product or component for service to/from the manufacturer or service center
c. Instruct the user of the proper use of the product
5. The cost for any inconvenience, personal injury or property damage due to failure of the product, and cost of
damage arising out of the transportation of the product which is covered under different terms with the carrier
6. Natural variations in color and finishes that are inherent to the material and unavoidable (and therefore not defects)
ALL IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY, SUITABILITY, QUALITY
AND/OR FITNESS FOR A PARTICULAR PURPOSE,ARE LIMITED IN DURATION TO THE EXPRESS WARRANTY PERIODS
SPECIFIED ABOVE FOR THE PARTS DESCRIBED THEREIN. EVO, INCORPORATED MAKES NO OTHER WARRANTYAND
WILL NOT BE LIABLE FORANY DIRECT OR INDIRECT, CONSEQUENTIAL OR INCIDENTAL DAMAGES. Some states do not
allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Neither Evo manufacturer
representatives and dealers, nor the commercial establishment selling this product has any authority to make any warranties
or to promise remedies in addition to or inconsistent with those stated above. The maximum liability to Evo, Incorporated in any
event, shall not exceed the purchase price of the product paid by the original commercial-purchaser. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This
warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
EVO COMMERCIAL LIMITED WARRANTY TERMS

INSTALLATION INSTRUCTIONS
Affinity 30Ge
Evo, Inc. | 8140 SW Nimbus Ave., Bldg 5 | Beaverton, Oregon 97008 USA
INSTALLATION CHECKLIST
UNPACK COOKTOP COMPONENTS 8
CLEARANCE DIMENSIONS 9
PREPARE COUNTER TOP FOR INSTALLATION 10 - 13
INSERT CHASSIS IN COUNTER TOP 14
INSTALL DRIP PAN AND DRIP PAN GASKET 15 - 16
ASSEMBLING COOK SURFACE RETAINING FASTENERS 17
CONNECTING TEMPERATURE SENSOR WIRE TO 18
COOKING SURFACE
POSITIONING TEMPERATURE SENSORS AND 19
LOWERING COOKING SURFACE
RETAINING COOKING SURFACE 20
CONNECT ELECTRICAL AND GAS LINES 21
DISPLAY PANELAND TEMPERATURE CONTROL 22 - 23
SPILLOVER TRAY REMOVALAND CLEANING 24
COOKING SURFACE MAINTENANCE 25
APPENDIX - CONTROL COMPONENTS 26 - 27
PAGE #

INSTALLATION INSTRUCTIONS
Affinity 30Ge
Evo, Inc. | 8140 SW Nimbus Ave., Bldg 5 | Beaverton, Oregon 97008 USA
8
Cook Surface: Lift and separate cook surface from unit and place next to installation area.
Drip Pan Gasket:
Gasket is secured
to top of drip tray.
Remove gasket
from drip tray
and set aside
for reinstallation.
Drip Pan
Unlatch pan
from circular
skirt, then
carefully lift and
separate drip
pan from unit
and place next
to installation
area. Take care
not to scratch
drip pan during
installation.
Chassis:
Lift chassis
from crating box
and place on
its side next to
installation area.
Use caution
since ignition
components
are exposed.
Metal Right Angle Brackets: Unscrew from unit
and keep screws and brackets handy for first
installation step.
3-wire service line: Black, white
and green
UNPACKING COOKTOP COMPONENTS
STEP 1: As you are unpacking the crate, make sure you locate all components before
installation.
Ignition components are exposed during uncrating and installation.
Use caution and do not alter factory set positions.
Use caution when lifting. The cook surface is heavy.
Remove Tie
Down Bolts
and Tabs
holding chassis
to packing crate
base using 7/16”
wrench.

INSTALLATION INSTRUCTIONS
Affinity 30Ge
Evo, Inc. | 8140 SW Nimbus Ave., Bldg 5 | Beaverton, Oregon 97008 USA
CLEARANCE DIMENSIONS
Read the instructions carefully in this booklet to install the
Evo Affinity 30Ge Cooktop to a metal, stone or wood countertop surface.
Cabinet layout and construction may vary.
12” clearance to sidewall
from cook surface
12” clearance to backwall
from cook surface
Minimum 3” clearance required under unit venting to 22 sq/in of combustible air.
Do not install above any equipment, table or shelving where
air temperature is greater than ambient air temperature.
CLEARANCE TO COMBUSTIBLE CONSTRUCTION FROM CHASSIS
Combustibles Non-combustibles
Back 3/8” 0”
Sides 3/8” 0”
Bottom 3” 3”
CLEARANCE TO COMBUSTIBLE SURFACE FROM COOKING SURFACE
Top 36”
Sides 12”
36” clearance to ceiling from cooktop surface
Keep combustible materials at least 36” away
from cooktop surface during operation

INSTALLATION INSTRUCTIONS
Affinity 30Ge
Evo, Inc. | 8140 SW Nimbus Ave., Bldg 5 | Beaverton, Oregon 97008 USA
10
271932
"
701.04mm
2734
"
704.85mm
11532
"
37.16mm
R18
18
"
460.38mm
1318
"
333.38mm
262332
"
678.51mm
131316
"
350.52mm
STEP 2: Mark the finished position of the Evo Affinity 30Ge drip pan on the countertop using
the dimensions shown. The circular dimension of 18-1/8” is the diameter of the drip pan to the
outside flange material thickness (located to the inside of the half-rolled bead edge). The drip
pan cutout must be made precisely to these dimensions (or at a maximum +1/16”) so that the
half-rolled top bead on the drip pan edge overhangs the cutout dimension by .25”.
(See following page for more detail)
Countertop with
substrate underlayment
OPENING IN COUNTERTOP FRONT
Countertop
overhang to
cabinet front
Cabinetry Box:
minimum 3 cm
below countertop
surface
TOP VIEW
COUNTERTOP INSTALLATION (1 of 4)
NOTE:
If the dimensions for the
countertop overhang and
countertop depth cutout
are not followed, there
will be a conflict with the
door swing which allows
access to the waste
containers.

INSTALLATION INSTRUCTIONS
Affinity 30Ge
Evo, Inc. | 8140 SW Nimbus Ave., Bldg 5 | Beaverton, Oregon 97008 USA
COUNTERTOP INSTALLATION (2 of 4)
CORRECTALIGNMENT OF DRIP PAN
AND CHASSIS TO COUNTERTOP INCORRECTALIGNMENT OF DRIP PAN
AND CHASSIS TO COUNTERTOP
Possible reasons for incorrect alignment:
1. Top of cabinetry box is less than 3 cm
(1.18”) from countertop.
2. Chassis mounting brackets are too high.
Black o-ring under
drip pan bead
STEP 2 Continued: Make sure cabinetry box is 1-1/2” below countertop surface and
mounting brackets are positioned correctly so drip pan and chassis are aligned to countertop.
(see diagrams above). A black o-ring is recessed in the top bead and designed to create a
seal against the countertop.
Also ensure allowance for the countertop overhang as shown on the SIDE VIEW
(see next page).
When you have confirmed the position is correct, cut the countertop and substrate.

INSTALLATION INSTRUCTIONS
Affinity 30Ge
Evo, Inc. | 8140 SW Nimbus Ave., Bldg 5 | Beaverton, Oregon 97008 USA
12
2514
"
641.35mm
6916
"
166.55mm
3X
7.65in
194.36mm
1316
"
30mm
22332
"
69.21mm
81532
"
215.32mm
SIDE VIEW
Example of 3/8” tile with substrate for a minimum 3 cm overall. Make sure you allow for the
countertop overhang as shown.
Metal
Right Angle
Mounting
Brackets
(supplied)
If desired, shelving
or drawers can be
installed under the
Affinity 30Ge.
Finished cabinet face
set back from finished
countertop front edge
COUNTERTOP INSTALLATION (3 of 4)

INSTALLATION INSTRUCTIONS
Affinity 30Ge
Evo, Inc. | 8140 SW Nimbus Ave., Bldg 5 | Beaverton, Oregon 97008 USA
1916
"
40mm
1316
"
30mm
2734
"
704.85mm
7.65in
194.36mm
Shelving or
drawers can
be installed
under Affinity
30Ge if
desired.
FRONT VIEW
STEP 3: Construct a bay for the Evo unit with your chosen cabinet system. Position and
fasten the supplied mounting brackets 7.65” below the finished countertop surface.
Metal right angle mounting brackets supplied with unit are
each 1/16” thick. Mount angle brackets as shown. Unit
slides into framework and rests on top side of brackets.
Brackets are slotted for fasteners at each four corners.
Cabinet
Framework
Example: Tiled countertop with substrate.
Finished countertop thickness should be
3 cm.
COUNTERTOP INSTALLATION (4 of 4)

INSTALLATION INSTRUCTIONS
Affinity 30Ge
Evo, Inc. | 8140 SW Nimbus Ave., Bldg 5 | Beaverton, Oregon 97008 USA
14
STEP 4: Slide the Affinity 30Ge chassis into the countertop so it rests on top of the installed
brackets. Bolt unit to angle brackets using supplied 1/4” x 20 fasteners from underside.
3 WIRE SERVICE LINE:
Black, White, and Green
120V, 1-Phase, 50-60Hz
15AMP Circuit
INSERT CHASSIS IN COUNTERTOP
Use supplied 1/4” fasteners to bolt
chassis to angle brackets.
Electrical and Gas Installation must be done by a licensed electrician and
plumber in accordance with local guidelines once unit has been completely
installed. Refer to pages 17-18 and 21 for further instructions.

INSTALLATION INSTRUCTIONS
Affinity 30Ge
Evo, Inc. | 8140 SW Nimbus Ave., Bldg 5 | Beaverton, Oregon 97008 USA
STEP 5: Slide drip tray over chassis circular skirt positioning spillover slots to the
corresponding slots of the top chassis deck. Notice the drip pan catches showing through the
inside cutout locations of the circular chassis skirt. From the inside of the skirt, use each of
the three latches to pull the drip pan down into the counter.
Drip Tray
Catches
POSITIONING DRIP PAN
GRILL FRONT

INSTALLATION INSTRUCTIONS
Affinity 30Ge
Evo, Inc. | 8140 SW Nimbus Ave., Bldg 5 | Beaverton, Oregon 97008 USA
16
STEP 6: Secure drip pan to chassis using access slot (A). Rewrap drip pan gasket around
top of drip tray and secure (B). Ensure seal under drip pan edge is touching countertop(C).
drip pan gasket
- seam at rear
(opposite to
chef side)
SECURING DRIP PAN AND GASKET
CROSS SECTION OF
CHASSIS ACCESS SLOT
Hook drip pan latch under
chassis catch and tighten
screw at chassis access slot.
A
Slip gasket ring onto top of
drip pan so it creates a seal to
the chassis skirt.
CROSS SECTION OF
DRIP PAN TOP CROSS SECTION OF
DRIP PAN EDGE
Ensure the black seal under
the drip pan bead edge is
touching the countertop.
B C
drip pan countertop
drip pan
chassis
skirt
Use No. 3 Phillips screwdriver
to secure drip pan at the
access points.

INSTALLATION INSTRUCTIONS
Affinity 30Ge
Evo, Inc. | 8140 SW Nimbus Ave., Bldg 5 | Beaverton, Oregon 97008 USA
17
STEP 7: Locate Parts Box shipped your Affinity 30G and the parts bag containing the Rear
Retaining Bullet Fastener, two each 1/4” x 20 hex bolt and locking nut, and two each J-Hook.
Follow the illustration show on this page. Using a 7/16” wrench tighten the Rear Retaining
Bullet to a cook surface tab as shown (Ensure the Rear Retaining Bullet is placed on the right
hand side of the tab). Next, loop the J-Hook through the inside slot of each remaining tab.
ASSEMBLING COOK SURFACE RETAINING FASTENERS
IT IS RECOMMENDED THE COOKING SURFACE BE PLACED ON A PROTECTED
WORK SURFACE WITH THE FLANGE FACING UPWARD.
Place Rear Retaining
Bullet Fastener on right
hand side of tab.
Using a 7/16” wrench,
tighten the Rear
Retaining Bullet to the
cooking surface tab with
two each 1/4” x 20 hex
bolt and locking nut.
Ensure the bolts are
tightened securely.
Loop the J-Hook
through the inside slot
of two tabs as shown.

INSTALLATION INSTRUCTIONS
Affinity 30Ge
Evo, Inc. | 8140 SW Nimbus Ave., Bldg 5 | Beaverton, Oregon 97008 USA
18
CONNECTING TEMPERATURE SENSOR WIRE TO COOKING SURFACE
1Inner Zone
2Outer Zone
3Outer Zone
4Outer Zone
1
2
4
3
Place suitable
protection on drip
pan when tilting
cook surface
upward.
J-Hook Guide
Tube
(2 tubes)
J-Hook
(2 hooks)
TC Wire
(4 wires total)
STEP 8: Place cook surface over circular skirt with the Rear Retaining Bullet facing opposite the front
control panel with the bullet resting on the chassis skirt.
STEP 9: Connect TC wires as per diagram and tighten with supplied nuts to each weld-stud location.
POSITION THE COOKING SURFACE ON THE CHASSIS AND ANGLE IT UPWARD TO
PROVIDE ACCESS FOR CONNECTING THE TEMPERATURE SENSOR (TC) WIRES.
DO NOT OVER TIGHTEN TC-WIRE HEX NUTS. DOING SO WILL BREAK THREADED
WELD STUD ON COOK SURFACE.
WITH THE COOKING SURFACE SUPPORTED IN AN UPRIGHT POSITION, GENTLY PULL
EACH TC WIRE UP THROUGH ITS GUIDE TUBE AND ATTACH TO ITS RESPECTIVE
THREADED STUD LOCATION ON THE UNDERSIDE OF THE COOKING SURFACE.
TC Wire
Guide Tube
(4 tubes)
Rear Retaining
Bullet Slot
TC Sensor Location

INSTALLATION INSTRUCTIONS
Affinity 30Ge
Evo, Inc. | 8140 SW Nimbus Ave., Bldg 5 | Beaverton, Oregon 97008 USA
POSITIONING TEMPERATURE SENSORS AND LOWERING COOKING SURFACE
TC (Thermal Couple temperature sensor)
TC’s are used to electrically monitor the cooking surface temperature at both the inner and outer zones. The
Affinity 30Ge uses K-Value TC’s.
Each TC wire location is illustrated by a number to highlight its corresponding threaded stud location. When the
cooking surface is lowered to its final location, the TC wires must be vertically aligned.
The Inner Zone (Inner Burner) has one TC at #1 position. The Outer Zone (Outer Burner) has three TC’s at
positions #2, #3, and #4 that are averaged.
Use a wood block (2x4) or similar item to prop
surface upward to provide access to TC wires.
STEP 10: Using wood blocks (2x4) or a similar means, lower the cook surface onto the burner
chassis with enough space to allow for positioning each TC wire into its respective guide tube.
Ensure all excess TC wire is pushed downward through the protective guide tubes and no
excess wire is exposed or near a burner tube.
STEP 11: Locate each J-Hook and place through the J-Hook Guide Tube. Continue lowering the
cooking surface onto the burner chassis.
Position Rear Retaining Bullet fully to the
right side of the retaining slot before lowering
cooking surface.
WHEN LOWERING COOK SURFACE ENSURE ALl SLACK TC WIRE IS PUSHED INTO
THE PROTECTIVE GUIDE TUBE WITH NO WIRE EXPOSED TO THE BURNERS.
Other manuals for Affinity 30Ge
2
Table of contents
Other Evo Cooktop manuals

Evo
Evo Affinity 30Ge Quick start guide

Evo
Evo Affinity 30Gp Quick start guide

Evo
Evo Affinity 30Ge User manual

Evo
Evo Affinity 30G Quick start guide

Evo
Evo Affinity 30G Quick start guide

Evo
Evo EVent 48E User manual

Evo
Evo Centric 20E Electric Owner's manual

Evo
Evo Affinity 30Gp Quick start guide

Evo
Evo Trim Kit for Evo Affinity 25G Quick start guide

Evo
Evo affinity 25E Quick start guide