Evo Affinity 30Ge Quick start guide

the natural way to cook
®
®
OWNER & INSTALLATION MANUAL
Affinity 30Ge
Cooktop
Evo, Inc. | 8140 SW Nimbus Ave., Bldg 5 | Beaverton, Oregon 97008 USA
Phone [phone] | Fax [phone] | www.evoamerica.com | [email protected]
Evo Afnity 30Ge
Electronically-Controlled Gas Cooktop
For Indoor Use Only
Certication: ANSI Z83.11b-2009/CSA 1.8B-2009. OMNI Report # 0141GM004S
Part #: Commercial models: 10-0050-NG | 10-0050-LP, Residential models: 10-0051-NG | 10-0051-LP,
Doc: OM-C&R-30Ge 09/2014
Copyright © 2015
This appliance and its individual shutoff valve must be
disconnected from the gas supply piping system during
any pressure testing of system at test pressures in
excess of 1/2 PSI (3.5kPa).
This appliance must be isolated from the gas supply
piping system by closing its individual manual shutoff
valve during any pressures testing of the gas supply
system at test pressures equal to or less than 1/2 PSI
(3.5kPa).
This appliance, when installed, must be electrically grounded in accordance with local codes,
or in the absence of local codes, with the National ELectrical Code, ANSI/NFPA70,
or the Canadian Electrical Code, CSA C22.2, as applicable.

INSTALLATION INSTRUCTIONS
Affinity 30Ge
Evo, Inc. | 8140 SW Nimbus Ave., Bldg 5 | Beaverton, Oregon 97008 USA
Phone [phone] | Fax [phone] | www.evoamerica.com | [email protected] 1
Grill is for indoor use only. Grill should be operated in a well-ventilated space. Never operate near
ammable liquids or vapors. Do not install or use grill within 36” of combustible materials from back and
sides of grill. Grill shall not be located under unprotected overhead made of combustible construction.
Warnings
FOR YOUR SAFETY
If You Smell Gas:
1. Shut off gas to appliance.
2. Extinguish any open ame.
3. Remove grill cooking surface.
4. If odor continues, immediately call your
gas supplier or your re department.
5. Evacuate all personnel from the area.
FOR YOUR SAFETY
1. Do not store or use gasoline or other
ammable vapors and liquids under
this appliance or in the vicinity of this
or any other appliance.
2. An LP Tank not connected for use shall
not be stored in the vicinity of this or
any other appliance.
Improper installation, adjustment, alteration, service or maintenance can cause property damage,
injury or death. Read the installation, operating and maintenance instructions thoroughly before
installing or servicing this equipment.
If you suspect a natural gas leak or other gas emergency and are unsure of its severity or what
to do, evacuate the area immediately and call 911 from a safe location.
POST THIS WARNING MESSAGE IN A PROMINENT LOCATION
Do not block or obstruct air ventilation for combustion.
WARNING
WARNING
This symbol identies the most important
safety messaging in this manual. When you
see this symbol, be alert to the possibility of
serious bodily injury if the instructions are not
followed. Be sure to read and carefully follow
all of the messages.
It is the responsibility of the assembler/owner to
assemble, install and maintain gas grill. Do not
let children operate or play near your grill. Failure
to follow these instructions could result in serious
personal injury and / or property damage.
WARNING
Do not attempt to light appliance during a power outage.
WARNING
WARNING

INSTALLATION INSTRUCTIONS
Affinity 30Ge
Evo, Inc. | 8140 SW Nimbus Ave., Bldg 5 | Beaverton, Oregon 97008 USA
Phone [phone] | Fax [phone] | www.evoamerica.com | [email protected]
2
THIS MANUAL MUST BE RETAINED FOR FUTURE REFERENCE. READ, UNDERSTAND,
AND FOLLOW THE INSTRUCTIONS AND WARNINGS CONTAINED IN THIS MANUAL.
DANGER POTENTIALLY HAZARDOUS SITUATION WHICH, IF NOT
AVOIDED, COULD RESULT IN DEATH
HIGH
VOLTAGE
CAUTION POTENTIALLY HAZARDOUS SITUATION WHICH, IF NOT AVOIDED,
MAY RESULT IN MINOR OR MODERATE INJURY.
WARNING POTENTIALLY HAZARDOUS SITUATION WHICH, IF NOT AVOIDED,
COULD RESULT IN DEATH OR SERIOUS INJURY
CAUTION Helpful tips and technique instructions are shown.
Notes
Complete Now For Future Reference
Model #_______________________________ Serial # _________________________________
Date Purchased ________________________ Location Purchased _______________________
Date Installed __________________________ Location Installed _________________________
The installation of this cooking equipment must conform with local codes, or in the
absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54, or the
Natural Gas and Propane Installation Code, CSA B149.1, as applicable.
To Installer or Person Uncrating Grill:
Leave these instructions with purchaser.
To Purchaser:
Keep these instructions for future reference.

INSTALLATION INSTRUCTIONS
Affinity 30Ge
Evo, Inc. | 8140 SW Nimbus Ave., Bldg 5 | Beaverton, Oregon 97008 USA
Phone [phone] | Fax [phone] | www.evoamerica.com | [email protected]
3
READ FIRST
IMPORTANT PRODUCT AND SAFETY INFORMATION
WARNING INSTALLATION OF THIS UNIT MUST BE DONE BY A QUALIFIED PLUMBER
AND ELECTRICIAN. INCORRECT INSTALLATION CAN CAUSE INJURY
TO PERSONNEL AND/OR DAMAGE TO EQUIPMENT. THIS UNIT MUST BE
INSTALLED IN ACCORDANCE WITH ALL LOCAL AND UNIFORM BUILDING/
CONSTRUCTION CODES.
WARNING DO NOT INSTALL THIS UNIT TO COMBUSTIBLE SURFACES, AND DO
NOT USE COMBUSTIBLE MATERIALS IN THE CONSTRUCTION OF ANY
COUNTER, STAND, OR OTHER DEVICE.
WARNING THIS UNIT IS EQUIPPED WITH A THREE-PRONG (GROUNDING) PLUG FOR
YOUR PROTECTION AGAINST SHOCK HAZARD AND MUST BE PLUGGED
INTO GROUNDED RECEPTACLE. DO NOT MODIFY, CUT, OR REMOVE THE
GROUNDING PRONG FROM THIS PLUG.
WARNING IMMEDIATELY AFTER CONNECTING GAS SUPPLY LINE AND BEFORE
FIRST IGNITION, CHECK ALL GAS CONNECTIONS WITH SOAPY WATER
TO TEST FOR LEAKS.
WARNING KEEP WATER AND ALL COOKING SPILL OVERS AWAY FROM FRONT
CONTROL PANEL AND ALL OPEN SERVICE AREAS. NEVER HOSE UNIT,
OR SPRAY UNIT WITH CLEANING SOLUTIONS.
CAUTION CAREFULLY FOLLOW ALL INSTALLATION INSTRUCTIONS AND
CONSTRUCT ALL COUNTER SPACE, STANDS, OR OTHER SURFACES TO
THE RECOMMENDED INSTALLATION SPECIFICATIONS AS OUTLINED IN
THIS MANUAL.
CAUTION THIS UNIT IS HEAVY AND SHOULD BE INSTALLED BY TWO PEOPLE.
USE NECESSARY BLOCKING FOR LOCATING COOK SURFACE AND
CONNECTING TEMPERATURE SENSORS TO THE UNDERSIDE OF COOK
SURFACE.
CAUTION ALWAYS KEEP ANY AND ALL FLAMMABLE LIQUIDS AND COMBUSTIBLE
MATERIALS AWAY FROM UNIT. DO NOT STORE TOWELS OR UTENSILS,
OR ANY OTHER ITEMS ON UNIT’S DRIP PAN.
CAUTION DO NOT CLEAN THE COOK SURFACE WITH GRILL BRICKS OR CLEANING
SOLUTIONS. USE ONLY GRILL SCREENS AND GRILL PADS AND FOLLOW
THE PRESCRIBED METHOD OF CLEANING AS OUTLINED IN THIS
MANUAL.
NOTICE THE SERIAL NUMBER AND MODEL INFORMATION LABEL PLATE IS
LOCATED UNDERNEATH THE CONTROL PANEL.
NOTICE INSTALLATION OF ANY VENT HOODS OR FIRE EXTINGUISHER SYSTEMS
MUST CONFORM TO THE NATIONAL, STATE, AND LOCAL BUILDING AND
ALL APPLICABLE UNIFORM CONSTRUCTION CODES.
NOTICE DURING THE FIRST FEW HOURS OF OPERATION IT IS NORMAL FOR OILS
USED IN THE MANUFACTURING PROCESS TO BURN OFF AND GIVE AN
ODOR OR PETROLEUM SMOKE.

INSTALLATION INSTRUCTIONS
Affinity 30Ge
Evo, Inc. | 8140 SW Nimbus Ave., Bldg 5 | Beaverton, Oregon 97008 USA
Phone [phone] | Fax [phone] | www.evoamerica.com | [email protected] 4
Evo, Incorporated warrants to the original residential consumer-purchaser that the Evo grill shall be free from rust-through on all
metal surfaces and shall be free from defects in materials and workmanship under normal and reasonable use from the original
date of purchase. Evo promises to replace, at its determination, any product or component that is defective and covered under
this warranty for as long as you, the registered original consumer-purchaser, owns the grill. This is your sole and exclusive
remedy. This warranty is for the benet of the original consumer-purchaser and is non-transferable. This warranty is subject to the
limitations, exclusions and other provisions listed below.
Limitations Involving Materials and Components:
Warranty does not apply to normal wear and tear, which are expected over the course of ownership. The materials and
components listed below are covered according to the following schedule from the original date of purchase:
• One Year – electrical and electronic components [including, but not limited to, electronic displays, overlay and membrane
switches, temperature sensors (RTD and K-Value Thermal Couple), hot surface igniters, computers, transformers,
heater elements, relays, igniters, ignition controllers, wiring, switches, encoders, outlets and plugs
• One Year – gas components [including, but not limited to, gas regulator, gas hoses, manifold assemblies]
• One Year – accessories and repair parts
The Warranty Registration Card (or online warranty registration form available at www.evoamerica.com/content/
residential-warranty-registration) must be completed and returned/submitted to Evo, Incorporated within 30 days from the
date of purchase. The original purchase invoice or payment record must be retained and produced upon request if claims
are made under this warranty. To receive a replacement Warranty Registration Card, write or call the address listed at the
bottom of this page. Warranties are void if the original serial numbers have been removed, altered, or cannot be readily
determined.
THIS WARRANTY APPLIES ONLY TO PRODUCTS PURCHASED AND LOCATED WITHIN THE UNITED STATES
OR CANADA.
WHAT IS NOT COVERED BY THIS WARRANTY
1. Conditions and damages resulting from any of the following:
a. Improper or inadequate installation, delivery, use, storage or maintenance
b. Any repair not authorized in writing by Evo, Inc., any modications, misapplications, or unreasonable use
c. Improper setting of any control
d. Harsh environmental conditions, including, but not limited to, continual seawater spray, high pressure water, and direct contact
with corrosive chemicals and materials
e. Excessive or inadequate electrical, or gas supply
f. Accidents, natural disasters, acts of God
g. Conditions covered by the purchaser’s insurance
h. Cleaning supplies and lters
2. Products purchased or utilized for commercial use without the express authorization of Evo, Incorporated for such use
3. Labor not pre-authorized by Evo, Incorporated, and labor not performed by an authorized Evo service agency or representative
4. Pre-authorized warranty labor performed outside of normal business hours, and at overtime and premium rates
5. The cost of service or a service call to:
a. Identify or correct installation errors
b. Transport the product or component for service to/from the manufacturer or service center
c. Instruct the user of the proper use of the product
6. The cost for any inconvenience, personal injury or property damage due to failure of the product, and cost of damage arising out
of the transportation of the product which is covered under different terms with the carrier
7. Natural variations in color and nishes that are inherent to the material and unavoidable (and therefore not defects)
ALL IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY, SUITABILITY,
QUALITY AND/OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE EXPRESS
WARRANTY PERIODS SPECIFIED ABOVE FOR THE PARTS DESCRIBED THEREIN. EVO, INCORPORATED
MAKES NO OTHER WARRANTY AND WILL NOT BE LIABLE FOR ANY DIRECT OR INDIRECT, CONSEQUENTIAL
OR INCIDENTAL DAMAGES. Some states do not allow limitations on how long an implied warranty lasts, so the above
limitation may not apply to you. Neither Evo manufacturer representatives and dealers, nor the retail establishment selling this
product has any authority to make any warranties or to promise remedies in addition to or inconsistent with those stated above.
The maximum liability to Evo, Incorporated in any event, shall not exceed the purchase price of the product paid by the original
consumer-purchaser. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitations or exclusions may not apply to you. This warranty gives you specic legal rights, and you may also have other rights
which vary from state to state.
EVO RESIDENTIAL LIMITED WARRANTY TERMS

INSTALLATION INSTRUCTIONS
Affinity 30Ge
Evo, Inc. | 8140 SW Nimbus Ave., Bldg 5 | Beaverton, Oregon 97008 USA
Phone [phone] | Fax [phone] | www.evoamerica.com | [email protected]
5
Evo, Incorporated warrants to the original commercial foodservice purchaser that the Evo cooking, refrigeration and ventilation
equipment shall be free from rust through on all metal surfaces and shall be free from defects in materials and workmanship under
normal and reasonable use for One Year from the original date of purchase from Evo, Inc. This warranty is for the benet of the
original use purchaser and is non-transferable. Evo promises to replace, at its determination, any product or component that is
defective during this initial one year period. Or as a resolution, Evo may at its option repurchase the product at its original purchase
price. This is your sole and exclusive remedy. This warranty is subject to the limitations, exclusions and other provisions listed
below.
Limitations Involving Materials and Components:
Warranty does not apply to normal wear and tear, which are expected over the course of ownership. The materials and
components listed below are covered according to the following schedule from the original date of purchase from Evo:
• One Year – electrical and electronic components [including, but not limited to, electronic displays, overlay and membrane
switches, temperature sensors (RTD and K-Value Thermal Couple), hot surface igniters, computers, transformers,
heater elements, relays, igniters, ignition controllers, wiring, switches, encoders, outlets and plugs
• One Year – gas components [including, but not limited to, gas regulator, gas hoses, manifold assemblies]
• One Year – accessories and repair parts
• Ninety (90) Days - refrigeration components [including, but not limited to, compressor, evaporator, pressure control units]
The Warranty Registration Card (or online warranty registration form available at www.evoamerica.com/content/
commercial-warranty-registration) must be completed and returned/submitted to Evo, Incorporated within 30 days from
the date of purchase. The original purchase invoice or payment record must be retained and produced upon request if
claims are made under this warranty. To receive a replacement Warranty Registration Card, write or call the address listed
at the bottom of this page. Warranties are void if the original serial numbers have been removed, altered, or cannot be
readily determined.
THIS WARRANTY APPLIES ONLY TO PRODUCTS PURCHASED AND LOCATED WITHIN THE USA OR CANADA.
What is NOT COVERED by this warranty:
1. Conditions and damages resulting from any of the following:
a. Improper or inadequate installation, delivery, use, storage or maintenance
b. Any repair not authorized in writing by Evo, Inc., any modications, misapplications, or unreasonable use
c. Improper setting of any control
d. Harsh environmental conditions, including, but not limited to, continual seawater spray, high pressure water, and direct contact
with corrosive chemicals and materials
e. Excessive or inadequate electrical, gas, or refrigeration supply
f. Accidents, natural disasters, acts of God
g. Conditions covered by the purchaser’s insurance
h. Cleaning supplies and lters
2. Labor not pre-authorized by Evo, Incorporated, and labor not performed by an authorized Evo service agency or
representative
3. Pre-authorized warranty labor performed outside of normal business hours, and at overtime and premium rates
4. The cost of service or a service call to:
a. Identify or correct installation errors
b. Transport the product or component for service to/from the manufacturer or service center
c. Instruct the user of the proper use of the product
5. The cost for any inconvenience, personal injury or property damage due to failure of the product, and cost of
damage arising out of the transportation of the product which is covered under different terms with the carrier
6. Natural variations in color and nishes that are inherent to the material and unavoidable (and therefore not defects)
ALL IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY, SUITABILITY, QUALITY
AND/OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE EXPRESS WARRANTY PERIODS
SPECIFIED ABOVE FOR THE PARTS DESCRIBED THEREIN. EVO, INCORPORATED MAKES NO OTHER WARRANTY AND
WILL NOT BE LIABLE FOR ANY DIRECT OR INDIRECT, CONSEQUENTIAL OR INCIDENTAL DAMAGES. Some states do not
allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Neither Evo manufacturer
representatives and dealers, nor the commercial establishment selling this product has any authority to make any warranties
or to promise remedies in addition to or inconsistent with those stated above. The maximum liability to Evo, Incorporated in any
event, shall not exceed the purchase price of the product paid by the original commercial-purchaser. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This
warranty gives you specic legal rights, and you may also have other rights which vary from state to state.
EVO COMMERCIAL LIMITED WARRANTY TERMS

INSTALLATION INSTRUCTIONS
Affinity 30Ge
Evo, Inc. | 8140 SW Nimbus Ave., Bldg 5 | Beaverton, Oregon 97008 USA
Phone [phone] | Fax [phone] | www.evoamerica.com | [email protected] 6
INSTALLATION CHECKLIST
UNPACK COOKTOP COMPONENTS 8
Follow unpacking instructions carefully
PREPARE COUNTERTOP FOR INSTALLATION 9-13
INSERT CHASSIS IN COUNTERTOP 14
INSTALL DRIP PAN 15-16
INSTALL DRIP PAN GASKET 16
INSTALL ELECTRICAL TC CONNECTIONS TO COOK SURFACE 17-18
INSTALL COOK SURFACE AND TIGHTEN FASTENERS 19-20
CONNECT ELECTRICAL AND GAS LINES 21
CHECK INSTALLATION 22
PAGE #

INSTALLATION INSTRUCTIONS
Affinity 30Ge
Evo, Inc. | 8140 SW Nimbus Ave., Bldg 5 | Beaverton, Oregon 97008 USA
Phone [phone] | Fax [phone] | www.evoamerica.com | [email protected]
7
Cook Surface: Lift and separate cook surface from unit and place next to installation area.
Drip Pan Gasket:
Gasket is secured
to top of drip tray.
Remove gasket
from drip tray
and set aside
for reinstallation.
Drip Pan
Unlatch pan
from circular
skirt, then
carefully lift and
separate drip
pan from unit
and place next
to installation
area. Take care
not to scratch
drip pan during
installation.
Chassis:
Lift chassis
from crating box
and place on
its side next to
installation area.
Use caution
since ignition
components
are exposed.
Metal Right Angle Brackets: Unscrew from unit
and keep screws and brackets handy for rst
installation step.
3-wire service line: Black, white
and green
UNPACKING COOKTOP COMPONENTS
STEP 1: As you are unpacking the crate, make sure you locate all components before
installation.
Ignition components are exposed during uncrating and installation.
Use caution and do not alter factory set positions.
Use caution when lifting. The cook surface is heavy.

INSTALLATION INSTRUCTIONS
Affinity 30Ge
Evo, Inc. | 8140 SW Nimbus Ave., Bldg 5 | Beaverton, Oregon 97008 USA
Phone [phone] | Fax [phone] | www.evoamerica.com | [email protected] 8
36” clearance to ceiling from cook surface
CLEARANCE DIMENSIONS
Read the instructions carefully in this booklet to install the
Evo Afnity 30Ge Cooktop to a metal, stone or wood countertop surface.
Cabinet layout and construction may vary.
12” clearance to sidewall
from cook surface
12” clearance to backwall
from cook surface
Minimum 3” clearance required under unit
venting to 22 sq/in of combustible air.
Do not install above any equipment, table or shelving where
air temperature is greater than ambient air temperature.
CLEARANCE TO COMBUSTIBLE CONSTRUCTION FROM CHASSIS
Combustibles Non-combustibles
Back 3/8” 0”
Sides 3/8” 0”
Bottom 3” 3”
CLEARANCE TO COMBUSTIBLE SURFACE FROM COOKING SURFACE
Top 36”
Sides 12”

INSTALLATION INSTRUCTIONS
Affinity 30Ge
Evo, Inc. | 8140 SW Nimbus Ave., Bldg 5 | Beaverton, Oregon 97008 USA
Phone [phone] | Fax [phone] | www.evoamerica.com | [email protected]
9
271932 "
701.04mm
2734 "
704.85mm
11532 "
37.16mm
R18
18
"
460.38mm
1318 "
333.38mm
262332 "
678.51mm
131316 "
350.52mm
STEP 2: Mark the nished position of the Evo Afnity 30Ge drip pan on the countertop using
the dimensions shown. The circular dimension of 18-1/8” is the diameter of the drip pan to
the outside ange material thickness (located to the inside of the half-rolled bead edge). The
drip pan cutout must be made precisely to these dimensions (or at a maximum +1/16”) so
that the half-rolled top bead on the drip pan edge overhangs the cutout dimension by .25”.
(See following page for more detail).
Countertop with substrate
underlayment
OPENING IN COUNTERTOP FRONT
Countertop
overhang to
cabinet front
Cabinetry Box:
minimum 3 cm
below countertop
surface
TOP VIEW
COUNTERTOP INSTALLATION (1 of 4)
NOTE:
If the dimensions for the
countertop overhang and
countertop depth cutout
are not followed, there
will be a conict with the
door swing which allows
access to the waste
containers.