Evonicfires WESTFIELD Manual

Suite Instrucon Guide
Important Safety Informaon
Always read this manual rst before aempng to install or use this
replace. For your safety, always comply with all warnings and safety
Instrucons contained in this manual to prevent personal injury or property
damage.
Please Note: This product is for well insulated spaces or
occasional use.
English Esuites-190108

welcome to evonicres
evonicres is an award-winning brand of CK Fires Ltd, situated just outside Straord-
upon-Avon, we manufacture a range of Brish built electric res and are considered as
one of the most technically advanced manufacturers in the world, with oponal
controllers such as e-touch and a fully integrated APP available to download on both
or .
This guide is designed to aid in the installaon and connued performance of this
product. This product conforms with all health, safety, and environmental protecon
standards as indicated by a CE mark. For opmum performance this product requires
a well insulated locaon or occasional use.
Contents
1. Introducon 2
2. Important Instrucons 3/4
3. Installaon Requirements 5/6
4. Installaon Method 7/8
5. E-Touch & App Interface 9
6. Product Operaon 10
7. Glass Removal 11/12
8. Log Set Guidance 13/14
9. Technical Specicaon 15
10. Problem Solving 16
11. Warranty 17
2.

IMPORTANT INSTRUCTIONS:
When using electrical appliances, basic precauons should always be
followed to reduce the risk of re, electric shock, and injury to persons,
including the following:
① Read all instrucons before using this electric replace.
② This replace is hot when in use. To avoid burns, do not let bare skin
touch hot surfaces. The trim around the heater outlet becomes hot during
heater operaon. DANGER: High temperatures may be generated under
certain abnormal condions. Do not parally or fully cover or obstruct the
front of this heater.
③ Extreme cauon is necessary when any heater is used by or near
children or people of reduced mobility and whenever the unit is le
operang and unaended.
④ Young children should be supervised to ensure that they do not play
with the appliance.
⑤ The appliance is not intended for use by young children or inrmed
persons without supervision.
⑥ In the event of a malfuncon, disconnect power at the service panel
and have the unit inspected by a reputable electrician before reusing.
⑦ If the supply cord is damaged, it must be replaced by the
manufacturer, or its service agent, or a qualied person in order to avoid a
hazard.
⑧ Do not use outdoors.
⑨ Never locate replace where it may fall into a bathtub or other water
container.
⑩ To disconnect the replace, turn the controls o, and turn o power to
heater circuit at main disconnect panel.
⑪ Do not run the cord under carpeng. Do not cover cord with throw
rugs, runners, or the like. Arrange cord away from trac area and where it
will not be tripped over.
⑫ Do not locate the heater immediately below a xed socket-outlet.
3.

㉑ Always use properly grounded & fused outlets.
㉒ Disconnect all power supply before performing any cleaning,
maintenance or relocaon of the unit.
㉓ When transporng or storing the unit and cord, keep in a dry
place, free from excessive vibraon and store so as to avoid
damage.
NOTE: Changes or modicaons not expressly approved by the
party responsible for compliance could void user's authority to
operate the equipment.
4.
⑬ Do not insert or allow foreign objects to enter any venlaon or
exhaust opening as this may cause an electric shock or re, or
damage to the heater.
⑭ To prevent a possible re, do not block air intakes or exhaust in
any manner.
⑮ All electrical heaters have hot and arcing or sparking parts
inside. Do not use in areas where gasoline, paint, or ammable
liquids are used or stored.
⑯ Use this replace only as described in this manual. Any other
use not recommended by the manufacturer may cause re, electric
shock or injury to persons.
⑰ Do not change the plug in any way. Always plug heaters directly
into a wall outlet/receptacle. Never use with an extension cord or
relocatable power tap (outlet/power strip).
⑱ Do not burn wood or other materials in the electric replace.
⑲ Do not strike the replace glass.
⑳ Always use a cered electrician should new circuits or outlets
be required.

INSTALLATION REQUIREMENTS:
Review and consider all of the following condions before installaon:
This appliance must only be connected to a 230/240 Volts AC 50Hz supply. Before connecng
the re, check that the supply voltage is the same as stated on the re. This appliance must only
be used on a AC supply, fuse rang 13Amp.
The wires in the mains lead are coloured in accordance with a standard UK supply, these be-
ing:
GREEN/YELLOW – EARTH
BLUE – NEUTRAL
BROWN – LIVE
Ensure the power cord is not installed so that it is pinched or against a sharp edge and ensure
that the power cord is stored or secured to avoid tripping or snagging to reduce the risk of re,
electric shock or injury to persons. Construcon and electrical outlet wiring must comply
with local building codes and other applicable regulaons to reduce the risk of re, electric
shock and injury to persons.
5.
WARNING: To reduce the risk of re, do not store or use gasoline or other ammable va-
pours or liquids in the vicinity of the heater.
1. Select a locaon that is not suscepble to moisture and is away from drapes, furniture
and high trac.
2. For ease of electrical hook up you may wish to locate the replace near an exisng
outlet (for plug-in convenience).
3. Remove electric replace, front glass and hardware from the box and remove all
Grounding Instrucons:
This product must be grounded. If it should malfuncon or breakdown, grounding provides a path of
least resistance for electric current to reduce the risk of electric shock.
This product is equipped with a cord having an equipment-grounding conductor and a grounding plug.
The plug must be plugged into an appropriate outlet that is properly installed and grounded in accord-
ance with all local codes and ordinances.
DANGER: Improper connecon of the equipment-grounding conductor can result in a risk of electric
shock. Check with a qualied electrician or serviceman if you are in doubt as to whether the product is
properly grounded. Do not modify the plug provided with the product – if it will not t the outlet, have
a proper outlet installed by a qualied electrician.
WARNING: Do not aempt to wire your own new outlets or circuits. To reduce the risk of re, electric
shock or injury to persons, always use a licensed electrician.

Installaon Method:
This product has been designed to be installed onto a plaster board,
drywalled, or exisng masonry chimney breast.
Please seek advice from a professional, with reference to the structural
integrity of the installaon site.
PLEASE NOTE: The screws and wall plugs provided are only suitable for a
solid wall xing / when installing onto a hollow-stud wall it is
recommended that heavy duty wall anchors or equivalent are used.
The product should never be sealed into a opening with the use of silicones
or adhesives as this can also alter the airow and hinder any further servicing
of the product.
Fig:3—Wall Mount Bracket xing points
Fig:1—Wall Mount Bracket
Fig:2— 840mm From oor
level to hole centres on Wall
Mount Bracket
Installing Product:
Each Compton2 & Compton 1000 product is supplied complete with one wall mounng
bracket. (See Fig:1)
Establish the desired nished height from oor level to the boom of the hearth of the
product.
(See Fig:2) - 840mm Dimension is used as standard installaon.
Fix the wall bracket to the wall ensuring to use the correct hardware xings given the
wall construcon, dry wall or Solid Wall.
(See Fig:3) - Five Fixing points for Wall Mount Bracket
6.

Once the Wall mount Bracket is securely in posion, Li and hook the product onto
the wall bracket, slong the wall bracket into the x3 slots in the rear of the product
(See Fig:4) ensuring to keep the product level.
Once the product is secured to the wall, Connect the power supply to the product—
Inlet located on the right-hand side underneath the hearth secon.
(See Fig:5)
Connect the power socket into the wall power outlet.
The product is now ready to use.
Fig:4— Li & Hook the prod-
uct onto the wall mount
bracket using x3 slots in
the rear of the product
Fig:5—Power supply inlet
Fig:4—Li & Hook product to
wall mount bracket
Fig:5—Power supply inlet
7.

E-Touch & App Interface:
The Appliance is operated using the E-Touch App Control.
The App Control can be used on either OS or Android operang systems.
To obtain the App please visit either the OS App Store Or Google Play and follow the on screen instrucons.
Screen shot taken from Apple App Store. Home Screen shot taken from E-Touch
App
8.

Product Operaon:
The appliance is operated by the e-touch App. The main
standby power switch to the suite product is located to the
right of the heater outlet, and is marked with a light bulb
image (Fig 1). To acvate the product, this switch must be
switch to the “ON” posion (Fig 2)
The rst me the e-series product is acvated both the illu-
minaon and heater will funcon, to switch the heater “O”
simply reduce the Room Temperature down to 10 degrees on
the App control.
9.
Fig 1.
Fig 2.

Glass Removal:
1. Remove 2 screws located in the boom glass retaining bar.
2. Remove the boom glass retaining bar.
10.

3. Remove the glass by pulling the second retaining bar away from the body of the re. Ensure
that the glass is supported at all mes. A sucon cup has been provided to aid with this step.
Please note: The sucon cup is provided for support only, not to hold the full weight of the
glass.
Please note: It is recommended that this step is carried out by 2 persons on
810/1500/1560/1800 models
11.

Log-Set Guidance:
Log Set
LOG LENGTH
A260MM
B370MM
C230MM
D185MM
E190MM
F390MM
Please Note: The images shown are suggested Log layouts, the log sets
can be arranged to personal preference.
12.
Midori Log Set

Please Note: The images shown are suggested Log layouts, the log sets
can be arranged to personal preference.
Compton 2 suggested log layout
Compton 1000 suggested log layout
13.

Technical Specicaon
MODEL WIDTH HEIGHT DEPTH
SIGMA 1156MM 1705MM 473MM
OMEGA 1500MM 900MM 380MM
HELIOS 1370MM 640MM 380MM
NIMBUS 1280MM 520MM 255MM
QUBE 1055MM 620MM 275MM
GALILEO 1175MM 945MM 255MM
ALTAIR 1087MM 1135MM 255MM
COMPTON1000 1500MM 520MM 365MM
COMPTON2 1120MM 520MM 365MM
EMPIRE2 1120MM 520MM 280MM
CASSINI 1297MM 1167MM 406MM
CORBIERE 1370MM 1095MM 355MM
MIDORI 530MM 620MM 320MM
KIBO 1258MM 889MM 241MM
BROADWAY 1500MM 520MM 365MM
WESTFIELD 860MM 625MM 280MM
14.

15.
Problem solving
(Heater unit cut-out) (This is a safety feature, to safe guard against further
damage to the product).
If the airow is restricted the heater will automacally turn o. This is can oc-
cur due to incorrect installaon or obstrucon.
To reset the heater funcon:
•isolate from the mains power supply.
•Leave product to cool.
•Aer a suitable cooling down period, remove the obstrucon if obstructed,
and check installaon.
•Aer 10 minutes the thermo switch (cut-out) in the heater will reset.
Please note that both the eect fan and heater fan emit a low decibel noise,
both of which are normal operang characteriscs.
• No power to the re: Check the wall socket, plug and fuse.
• No illuminaon: Make sure the re is turned on. Check heater is work-
ing, if so check that the dimmer control is set to full on the e-touch app/
e-touch controller.
• Illuminaon but no heat: The safety cut has operated see note on oper-
ang the Fire.
• Noise when illuminated: Due to moving parts, the electric re will make
a noise.
• Noise from the heater when in use: The sound of rushing air is normal.
• Reporng a fault: If a product is encountering a fault with the operaon
and a service engineer is required, please visit : www.evonicres.co.uk
and complete the elds required under the Report a Fault secon.
Please refer to the terms of your warranty.

Condions of warranty:
If this appliance should prove to be defecve due to faulty design, materials or
workmanship within 12 months of purchase, the product will be repaired free
of charge, subject to the following condions:
The electric re shall have been purchased and used solely within the
territory for domesc purposes and in accordance with the Users operang
instrucons.
It is the purchasers responsibility to prove that the unit is under warranty, e.g.
receipt of purchase.
All warranes, will be invalidated if unauthorised repairs or modicaons are
made to the electric re, or in case of accident, misuse or damage caused by
improper installaon, or to damage occurring during transit to or from the re-
pairer and altered or missing serial numbers.
Any parts, which have been replaced under this warranty, shall become our
property.
The company shall not be liable for any consequenal loss or damage what so
ever, arising from or in connecon with this electric re.
This Warranty does not apply to Heang elements, Bulbs or fuses.
‘No fault found’, service calls and installaon errors are not covered under the
manufacturers warranty and will result in a charge being made for the Call-Out
by our appointed service engineer.
This warranty is in addion to and does not aect the purchasers statutory
rights of consumers.
Registering product:
To register a product please visit: www.evonicres.co.uk
and complete the elds required under the Register a
Product Secon. By registering your appliance, an extra 12
months is added to your warranty
CK Fires Ltd / Evonic Fires
1 Evonic house, Clifford park, Clifford lane, Stratford-Upon-
Avon, CV37 8HW
Tel: [phone] Fax: [phone]
16.