Extech Instruments MO230 User manual

User Guide
Moisture Meter
Model MO230
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

MO230-en-GB_v3.3 2/15
2
Introduction
Congratulations on your purchase of the Extech MO230 Moisture Meter. The MO230 detects moisture
in wood and building materials such as wall board, sheet rock, cardboard, paper, mortar, and plaster.
Additionally, the meter measures Relative Humidity (RH) and Temperature. This device is shipped fully
tested and calibrated and, with proper use, will provide years of reliable service. Please visit our
website to check for the latest version of this User Guide, Product Updates,
Product Registration, and Customer Support.
Description
Meter Description
1. Protective Cap
2. Test Point pairs
3. Measurement electrode pins
4. Temperature and RH sensors
5. LCD
6. Hand grips
7. SET, CLEAR, and MODE/POWER buttons
Display Description
1. Measured value scale
2. Measured value
3. Relative Dry-Moist-Wet scale
4. Building mode and groups
5. Wood mode and groups
6. MAX value scale
7. TEST mode icon
8. Battery Status Indicator
9. Temperature or Relative Humidity display
Note: The LCD screen is optimized for a 30 degree viewing angle.
1
2
3
5
7
6
4
BUILD
%
W2 W3 B2 B3 B4B1
TEST
%
CF
1
2
3
4
5
6
7
89
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

MO230-en-GB_v3.3 2/15
3
Operation
Getting Started
1. Remove the protective cap to expose the electrode measurement pins.
2. Press and hold the power button for 2 seconds to switch the meter ON. The ambient
temperature will display and then the display will switch to the moisture measurement mode.
Note: To conserve battery life, the meter automatically shuts off after 3 minutes.
Measuring Temperature and Relative Humidity
The MO230 measures ambient temperature and relative humidity via the built-in sensors at the
top of the meter. The ambient temperature is used as a temperature compensation utility for
moisture measurements.
1. The temperature or humidity reading is shown at the top of the LCD display window.
2. Press and hold the SET button for 2 seconds to switch from temperature display to humidity
display.
Note: Refer to the programming section of this guide for instructions on switching the temperature
units of measure (oC / oF).
Measuring Moisture
1. The MO230 measures moisture via the pins affixed to the top of the
meter.
2. Carefully push the electrode pins as far as possible into the material
under test. The pins should be inserted into wood perpendicular to the
wood’s fiber structure.
3. Take several readings in several locations on the material for the best
representation of the amount of moisture present.
4. Read the measurement values on the display. Readings are
represented in %. The measurement range for wood is 1 to 75%. The
measurement range for other building materials is 0.1 to 24%.
5. Replace the protective cap when finished.
Maximum (MAX) reading Indication
The bargraph on the left side of the LCD display indicates and holds the
highest reading encountered during a measurement session. Use the
CLEAR button to reset the MAX reading indication.
CAUTION: The electrode measurement pins are extremely sharp; Use care when handling.
Cover the pins with the protective cap when the instrument is not in use.
%
C
BUILD
%
C
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

MO230-en-GB_v3.3 2/15
4
Measurement Modes
There are three (3) measurement modes. Momentarily press the MODE button to step from one
mode to the next:
WOOD MEASUREMENT MODE (WOOD GROUPS WI, W2, W3)
BUILDING MEASUREMENT MODE (MATERIAL GROUPS B1, B2, B3, B4)
SELF TEST MODE (TEST)
Wood Measurement mode
Momentarily press the MODE button to select the Wood Measurement
Mode. Use the SET button to choose the desired wood group (W1, W2,
W3) (refer to the Wood Group Table in the Appendix).
Building Material Measurement Mode
Momentarily press the MODE button to select the Building Measurement
Mode and use the SET button to choose the desired building material
group (B1, B2, B3, B4). (refer to the Building Material Group Table in the Appendix).
Self Test Mode
Momentarily press the MODE button to select the Self Test Mode. Touch the
measurement pins to the test points labeled ‘T’ on the protective cap. The
display will read OK if the test passes (30 units ±2) or it will display dashes if the
test fails. Next, touch the measurement pins to the test points labeled ‘B’. The
display will read OK if the test passes (60 ±2) or it will display dashes if the test
fails. If tests are failing please return the unit for repair or replacement.
Dry/Wet Indication
Moisture reading will also be displayed on the user defined wet-moist-
dry display. Setting the range of the display is described in the
programming section.
W2 W3
BUILD
B2 B3 B4B1
TEST
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

MO230-en-GB_v3.3 2/15
5
Programming Menu
The programming menu offers five configurable parameters. To access the menu, turn the meter
on, then momentarily press and release the SET and CLEAR buttons at the
same time.
Once in the programming menu, use the MODE button to step through the
parameters and also to exit the mode.
Material Temperature Offset
The first parameter in the programming menu is the material temperature offset feature. Use the
SET button to increase the temperature value and use the CLEAR button to decrease the
temperature value.
Material moisture measurements can be dependent on the temperature of the material. This
meter automatically compensates for material temperature changes by measuring ambient
temperature. The temperature offset allows for adjusting the temperature reading when the
material measured is not at ambient temperature.. Note: the temperature reading will return to
normal when the meter is turned off.
DRY/WET Scale
The second and third parameters in the programming menu set the lower and upper range of the
Dry-Wet scale. This relative scaling allows the user to specify what value is considered a DRY
reading and what value is considered a WET reading. The values can be programmed from 0000
to 0999 (999=99.9%). Use the SET button to increase the displayed value and use the CLEAR
button to decrease the displayed value.
LCD Backlight Modes
The fourth parameter is the LCD backlight configuration. There are three (3) LCD backlight
modes: AUTO, ON, and OFF. In AUTO mode, the backlight switches ON and OFF automatically
according to use. In the ON mode, the backlight is always ON. In the OFF mode, the backlight is
always OFF. The default setting is the AUTO mode. Use the SET button to select the mode.
Temperature units of measure (°C / °F)
The fifth mode is the temperature unit selection. The units of measure for ambient temperature
and material compensation can be set to either °C or °F. The setting is stored and remains in
effect until it is changed manually. Use the SET button to toggle the units.
Maintenance
Always keep the instrument dry
Prevent dirt from accumulating at the electrode pins
Electrode Pin Replacement
To replace the two electrode pins:
1. Remove the protective cap
2. Unscrew the electrode pins
3. Install the new pins
4. Replace the protective cap
F
TEMP
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

MO230-en-GB_v3.3 2/15
6
Battery Installation and Replacement
If the instrument does not switch on or if it displays the low battery symbol,
replace the batteries:
1. Remove the Phillips head screw at the rear of the instrument and
remove the battery compartment cover.
2. Install new batteries (2) by placing the edge of the battery under to
lip (3) and pressing the battery until the latch (1) locks the battery in
place.
3. Observe the correct polarity when installing batteries.
4. Remove old batteries by pressing the latch (1) and allowing the
battery to pop out.
5. Replace and secure the battery cover.
Note: Do not mix old and new batteries, always replace all three batteries.
You, as the end user, are legally bound (EU Battery ordinance) to return all used
batteries, disposal in the household garbage is prohibited! You can hand over your
used batteries / accumulators at collection points in your community or wherever batteries /
accumulators are sold!
Disposal: Follow the valid legal stipulations in respect of the disposal of the device at the
end of its lifecycle
+
12
3
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

MO230-en-GB_v3.3 2/15
7
Specifications
Measurement Principle Electrical resistance
Display LCD
Measurements Moisture, Relative Humidity and Temperature
Relative Humidity Range 0 to 100%
Temperature Range -40 to 70°C (-40 to 158°F)
Electrode length 8mm (0.3”)
Electrode pins Integrated, replaceable
Auto Power OFF After 3 minutes
Power supply Three (3) CR-2032 button cells
Operating Temperature 0 to 40°C (32 to 104°F)
Operating Humidity 85% Relative Humidity maximum
Housing material Impact resistant plastic
Dimensions 159 x 63.5 x 30.5mm (6.25 x 2.5 x 1.2”)
Weight 100g (3.5 oz)
Function Range Accuracy
Moisture in wood 0 to 30% ± 1%
30 to 60% ± 2%
60 to 75% ± 4%
Moisture in building
materials 0.1 to 2.4% ± 0.5%
Ambient Temperature -40 to -10°C ± 2°C
40 to 70°C ± 2°C
-10 to 40°C ± 1°C
Ambient Relative
Humidity
0 to 20% 5%
80 to 100% 5%
20 to 80% 3.5%
Copyright©2014‐2015FLIRSystems,Inc.
Allrightsreservedincludingtherightofreproductioninwholeorinpartinanyform
ISO‐9001Certified
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]

MO230-en-GB_v3.3 2/15
8
Appendices
Wood Groups
W1 W1 W2 W3
Abachi Agda Mahogany Afrormosia
Abura Maple Pine Rubber tree
Pear wood Alder Cherry wood Imbuia
Black Afara Patagonian cypress Kosipo Kokrodua
Parana pine Purpleheart Larch Niove Bidinkala
Beech Andiroba Limba Tola-real,red
Dabema Aspen Cherry mahogany Cork
Ebony Balsa Meleze Melamine particle board
Oak,red Basralocus Poplar (all) Phenolic resin particle board
Oak,white Tree Health Plum wood
Ash Ebiara Pine
Yellowheart Birch Red sandalwood
Ash-American Logwood Elm
Ash-Japanese Juniper Maritime pine
Hichory-silver poplar Beech-European hombean English oak
Hickory-swap Hombeam-white Durmast oak
Ilomba Campeachy Tola
Ipe Aiele Tola-branca
Iroko Kapok Walnut
Small-leaved lime Douka Westem red
Small-leaved lime -
American Douglas fir Cedar
Mockemut hickory Oak White maple
Niangon Oak-holm White birch
Niove English,dumast White beech
Okoume Emien White poplar
Rosewood Alder-red,black Swiss pine
Rio rosewood Ash Common aspen
Common beech Yellow birch Damson wood
Red oak Southem yellow pine Cypress,red
Teak Hombeam Fibre board
Willow Hickory-silver poplar Wood fibre insulating board
White oak hickory-poplar Wood fibre hardboard
Cedar Izombe Kauramin partide board
Cypress - C. Lusit Guanandi Paper
Board Jarrah Textiles
Chestnut-sweet, red Elm
African Karri
Building Material Groups
B1 B2 B3 B4
Gypsum plaster Aerated concrete Sand/Cement top mix Concrete
www.GlobalTestSupply.com
Find Quality Products Online at: [e-mail]