Extech Instruments IR100 User manual

User's Manual Pocket InfraRed Thermometer
Model IR100
Introduction
Congratulations on your purchase of Extech’s IR100 Pocket InfraRed Thermometer. This device allows the user to take non-contact temperature
measurements simply by pointing the meter and pressing a button. This meter is shipped fully tested and calibrated and with proper use will provide years of
reliable service.
IR100 V1/2 04/08
1
2
3

Support line [phone]
Technical Support: Extension 200; E-mail: [email protected]
Repair & Returns: Extension 210; E-mail: [email protected]
Product specifications subject to change without notice
For the latest version of this User Guide, Software updates, and other
up-to-the-minute product information, visit our website: www.extech.com
Extech Instruments Corporation, 285 Bear Hill Road, Waltham, MA 02451
Operation
IR Temperature Measurements
Point the IR sensor toward object to be measured,
Press and Hold the MEASURE button.
The meter will turn ON, “SCAN” will flash in the display and the
measured surface temperature will appear in the display.
Release the MEASRE button, “HOLD” will appear in the display and
the meter will turn off after 15 seconds.
Max display
Release the MEASURE button so that “HOLD” is in the display.
Press the “Mode” button once and “MAX” appears in the display.
Press and Hold the MEASURE button. The display will only capture a
new reading if it is higher than the previous one.
Min display
Release the MEASURE button so that “HOLD” is in the display.
Press the “Mode” button twice and “MIN” appears in the display.
Press and Hold the MEASURE button. The display will only capture a
new reading if it is lower than the previous one.
Lock (disable auto-power off)
Release the MEASURE button so that “HOLD” is in the display.
Press the Mode button three times and the LOCK icon will flash.
Press and Release the MEASURE button to “Lock” the meter in the
On position.
Press the Mode button once to exit LOCK mode.
Displaying °F or °C
Release the MEASURE button so that “HOLD” is in the display.
Press the Mode button four times until the °F or °C icon starts to flash.
Press and hold the MEASURE button until the unit of measure
changes
Meter Description
1. LCD Display
2. Measure button
3. Mode button
Measurement considerations
The object being measured should be larger than the spot size as
illustrated in the distance to spot diagram.
If the surface of an object to be measured is covered with frost, dust or
other materials, surface cleaning must be performed before accurate
measurements can be made. High Reflective Surfaces: If the
surface of an object to be measured is highly reflective with a very low
emissivity value, apply masking tape or apply flat black paint to the
surface to improve the accuracy of the measurement.
Battery Replacement
A flashing battery icon on the display indicates that the battery which
powers the meter has weakened. Open the battery compartment on the
rear of the meter, replace the battery and close the compartment.
Warranty
EXTECH INSTRUMENTS CORPORATION (A FLIR COMPANY) warrants this instrument to
be free of defects in parts and workmanship for one year from date ofshipment (a six month
limited warranty applies on sensors and cables). If it should become necessary to return the
instrument for service during or beyond the warranty period, contact the Customer Service
Department at [phone] for authorization. A Return Authorization (RA) number must
be issued before any product is returned to Extech. The sender is responsible for shipping
charges, freight, insurance and proper packaging to prevent damage in transit.
This warranty does not apply to defects resulting from action of the user such as misuse,
improper wiring, operation outside of specification, improper maintenance or repair, or
unauthorized modification. Extech specifically disclaims any implied warranties or
merchantability or fitness for a specific purpose and will not be liable for any direct, indirect,
incidental or consequential damages. Extech's total liability is limited to repair or
replacement of the product. The warranty set forth above is inclusive and no other warranty,
whether written or oral, is expressed or implied.
Specifications
Ranges -34 to 446°F (-33 to 230°C)
Resolution 0.5°F/0.2°C
Accuracy ± 2.5% of reading or 5ºF (2.5ºC),
whichever is greater
Recommended
measuring distance 2” to 36” / 5cm to 91cm
Emissivity settings 0.95 fixed
Distance to Target Ratio 1:1
Display 3 ½ -digit (2000 count) LCD display
Power off Automatic shutoff after approx. 15
seconds
Operating Temperature 32 to 122°F (0 to 50°C)
Operating Humidity Max. 80% RH
Power Supply 1 x CR2032 (3V battery)
Weight 2.7 oz. / 76g
Size 3 x 1.6 x 0.7" (76.2 x 41 x 17.8 mm)
Copyright ©2008 Extech Instruments Corporation (a FLIR company)
All rights reserved including the right of reproduction in whole or in part in any form.

All Datasheets Cannot Be Modified Without Permission
Copyright © Each Manufacturing Company
This datasheet has been downloaded from:
www.EEworld.com.cn
Free Download
Daily Updated Database
100% Free Datasheet Search Site
100% Free IC Replacement Search Site
Convenient Electronic Dictionary
Fast Search System
www.EEworld.com.cn