Extraflame ANGY User manual

MADE IN ITALY
design & production
ANGY
UK pellet stoves UseR MANUAl
004281159 - Rev.000

2ENGLISH
APPLY TECHNICAL
DATA LABEL

3ENGLISH
ENGLISH............................................................................................................................................................................................................ 4
WarNINGS........................................................................................................................................................................................................ 4
SafEty.............................................................................................................................................................................................................. 4
routINE MaINtENaNcE................................................................................................................................................................................ 6
INStaLLatIoN.................................................................................................................................................................................................. 7
PREPARATIONS FOR MAINTENANCE..................................................................................................................................................................................................7
HErMEtIcaLLy SEaLEd INStaLLatIoN ....................................................................................................................................................... 9
COMbuSTION AIR ......................................................................................................................................................................................................................................9
FuMES EXHAuST SYSTEM.......................................................................................................................................................................................................................9
dEtaILS of aNGIE......................................................................................................................................................................................... 10
StovE poSItIoNING ..................................................................................................................................................................................... 11
NotE for corrEct fuNctIoNING ........................................................................................................................................................... 11
FuSE...............................................................................................................................................................................................................................................................11
uppEr fuMES outLEt aSSEMBLy .............................................................................................................................................................. 12
pELLEtS aNd LoadING ................................................................................................................................................................................ 13
pELLEt HoppEr ............................................................................................................................................................................................ 13
radIo/EMErGENcy card ........................................................................................................................................................................... 14
radIo coNtroL............................................................................................................................................................................................ 15
CONFIGuRATION......................................................................................................................................................................................................................................15
RAdIO CONTROl dEvICE ROOM PRObE CAlIbRATION...........................................................................................................................................................15
bATTERY TYPE ANd REPlACEMENT.................................................................................................................................................................................................15
radIo coNtroL dEvIcE fEaturES ........................................................................................................................................................... 16
dISpLay .......................................................................................................................................................................................................... 17
GENEraL MENu ............................................................................................................................................................................................. 18
GENERAl wARNINGS..............................................................................................................................................................................................................................18
fIrSt IGNItIoN SEttINGS............................................................................................................................................................................ 19
dATE/TIME ..................................................................................................................................................................................................................................................19
lANGuAGE..................................................................................................................................................................................................................................................19
dEGREES ......................................................................................................................................................................................................................................................19
opEratIoN aNd LoGIc................................................................................................................................................................................ 20
ModES ............................................................................................................................................................................................................ 21
vENtILatIoN.................................................................................................................................................................................................. 21
EaSy SEtup.................................................................................................................................................................................................... 21
cHroNo.......................................................................................................................................................................................................... 22
ENAblING....................................................................................................................................................................................................................................................22
CHRONO MOdE........................................................................................................................................................................................................................................22
PRG 1-4 .........................................................................................................................................................................................................................................................22
EXAMPlE......................................................................................................................................................................................................................................................23
CHRONO TIME SlOT................................................................................................................................................................................................................................23
MANuAl.......................................................................................................................................................................................................................................................23
AuTOMATIC ................................................................................................................................................................................................................................................23
AuX ................................................................................................................................................................................................................................................................23
SEttINGS ........................................................................................................................................................................................................ 24
dISPlAY........................................................................................................................................................................................................................................................24
STANd bY.....................................................................................................................................................................................................................................................24
OPERATION wITH AddITIONAl THERMOSTAT (OPTIONAl) .................................................................................................................................................24
dElTA-T ........................................................................................................................................................................................................................................................25
FIRST lOAd.................................................................................................................................................................................................................................................25
RESET.............................................................................................................................................................................................................................................................25
EASY CONTROl.........................................................................................................................................................................................................................................25
wI-FI...............................................................................................................................................................................................................................................................25
OPERATION ANd SOluTIONS.............................................................................................................................................................................................................26
RAdIO PRObE.............................................................................................................................................................................................................................................26
dEPRESSuRE NOTICE..............................................................................................................................................................................................................................26
addItIoNaL fuNctIoNS............................................................................................................................................................................. 27
AddITIONAl THERMOSTAT INSTAllATION (OPTIONAl).........................................................................................................................................................27
dElAY SwITCH-OFF.................................................................................................................................................................................................................................27
cLEaNING aNd MaINtENaNcE................................................................................................................................................................... 28
MaINtENaNcE............................................................................................................................................................................................... 28
PERIOdIC ClEANING uNdER uSER RESPONSIbIlITY................................................................................................................................................................28
routINE MaINtENaNcE pErforMEd By quaLIfIEd tEcHNIcIaNS .................................................................................................... 30
dECOMMISSIONING (ENd OF SEASON) .........................................................................................................................................................................................30
dISpLayS ........................................................................................................................................................................................................ 33
aLarMS .......................................................................................................................................................................................................... 33
dISpoSaL........................................................................................................................................................................................................ 35
attENtIoN
SurfacES caN BEcoME vEry Hot!
aLWayS uSE protEctIvE GLovES!
During combustion, thermal energy is released that signicantly increases the heat of surfaces, doors, handles, controls, glass, exhaust
pipes, and even the front of the appliance. Avoid contact with those elements if not wearing protective clothing (protective gloves
included). Make sure children are aware of the danger and keep them away from the stove during operation.

4ENGLISH
Warnings
This instructions manual is an integral part of the product: make sure that
it always accompanies the appliance, even if transferred to another owner
or user, or if transferred to another place. If it is damaged or lost, request
another copy from the area technician. This product is intended for the use
for which it has been expressly designed. The manufacturer is exempt from
any liability, contractual and extracontractual, for injury/damage caused to
persons/animals and objects, due to installation, adjustment and mainte-
nance errors and improper use.
Installation must be performed by qualied sta, which assumes com-
plete responsibility for the denitive installation and consequent good
functioning of the product installed. One must also bear in mind all laws
and national, regional, provincial and town council Standards present
in the country in which the appliance has been installed, as well as the
instructions contained in this manual.
The use of the appliance must comply with all local, regional, national
and European regulations.
The Manufacturer cannot be held responsible for the failure to comply
with such precautions.
After removing the packaging, ensure that the content is intact and com-
plete. Otherwise, contact the dealer where the appliance was purchased.
All electric components that make up the product must be replaced with
original spare parts exclusively by an authorised after-sales centre, thus
guaranteeing correct functioning.
safety
THE APPLIANCE MAY BE USED BY CHILDREN 8 YEARS OF AGE OR
OLDER AND INDIVIDUALS WITH REDUCED PHYSICAL, SENSORY, OR
MENTAL CAPACITIES OR WITHOUT EXPERIENCE OR THE NECESSARY
KNOWLEDGE, PROVIDED THAT THEY ARE SUPERVISED OR HAVE
We thank you for having chosen our company; our product is a great heating solution developed from the
most advanced technology with top quality machining and modern design, aimed at making you enjoy the
fantastic sensation that the heat of a ame gives, in complete safety.

5ENGLISH
RECEIVED INSTRUCTIONS ON SAFE USE OF THE APPLIANCE AND THAT
THEY UNDERSTAND THE INHERENT DANGERS.
THE GENERATOR MUST NOT BE USED BY PERSONS INCLUDING
CHILDREN WITH REDUCED PHYSICAL, SENSORY AND MENTAL
CAPACITIES OR WHO ARE UNSKILLED PERSONS, UNLESS THEY ARE
SUPERVISED AND TRAINED REGARDING USE OF THE APPLIANCE BY A
PERSON RESPONSIBLE FOR THEIR SAFETY.
THE CLEANING AND MAINTENANCE REQUIRED BY THE USER MUST
NOT BE PERFORMED BY CHILDREN WITHOUT SUPERVISION.
CHILDREN MUST BE CHECKED TO ENSURE THAT THEY DO NOT PLAY
WITH THE APPLIANCE.
DO NOT TOUCH THE GENERATOR WHEN YOU ARE BAREFOOT OR
WHEN PARTS OF THE BODY ARE WET OR DAMP.
IT IS FORBIDDEN TO MODIFY THE APPLIANCE IN ANY WAY.
DO NOT PULL, REMOVE, TWIST THE ELECTRICAL CABLES COMING
OUT OFTHE PRODUCT EVEN IF IT IS DISCONNECTED FROM THE MAINS.
IT IS ADVISED TO POSITION THE POWER SUPPLY CABLE SO THAT IT
DOES NOT COME INTO CONTACT WITH HOT PARTS OF THE APPLIANCE.
THE POWER SUPPLY PLUG MUST BE ACCESSIBLE AFTER
INSTALLATION.
DO NOT CLOSE OR REDUCE THE DIMENSIONS OFTHE AIRING VENTS
IN THE PLACE OF INSTALLATION. THE AIRING VENTS ARE ESSENTIAL
FOR CORRECT COMBUSTION.
DO NOT LEAVE THE PACKAGING ELEMENTS WITHIN REACH OF
CHILDREN OR UNASSISTED DISABLED PERSONS.
THE HEARTH DOOR MUST ALWAYS BE CLOSED DURING NORMAL
FUNCTIONING OF THE PRODUCT.
WHEN THE APPLIANCE IS FUNCTIONING AND HOT TO THE TOUCH,
ESPECIALLY ALL EXTERNAL SURFACES, ATTENTION MUST BE PAID
CHECK FOR THE PRESENCE OF ANY OBSTRUCTIONS BEFORE
SWITCHING THE APPLIANCE ON FOLLOWING A PROLONGED PERIOD
OF INACTIVITY.
THE GENERATOR HAS BEEN DESIGNED TO ADJUST ITSELF
AUTOMATICALLY IN PARTICULAR OPERATING CONDITIONS
THE GENERATOR HAS BEEN DESIGNED TO FUNCTION IN ANY
CLIMATIC CONDITION. IN PARTICULARLY ADVERSE CONDITIONS

6ENGLISH
STRONG WIND, FREEZING SAFETY SYSTEMS MAY INTERVENE
THAT SWITCH THE GENERATOR OFF. IF THIS OCCURS, CONTACT THE
TECHNICAL AFTERSALES SERVICE AND ALWAYS DISABLE THE SAFETY
SYSTEMS.
IN THE EVENT THE FLUE CATCHES FIRE, USE SUITABLE SYSTEMS
FOR SUFFOCATING THE FLAMES OR REQUEST HELP FROM THE FIRE
BRIGADE.
THIS APPLIANCE MUST NOT BE USED TO BURN WASTE
DO NOT USE ANY FLAMMABLE LIQUIDS FOR IGNITION
DURING THE FILLING PHASE DO NOT PUT THE BAG OF PELLETS TO
INTO CONTACT WITH THE PRODUCT
THE MAJOLICAS ARE TOP QUALITY ARTISAN PRODUCTS AND
AS SUCH CAN HAVE MICRODOTS, CRACKLES AND CHROMATIC
IMPERFECTIONS. THESE FEATURES HIGHLIGHT THEIR VALUABLE
NATURE. DUE TO THEIR DIFFERENT DILATION COEFFICIENT, THEY
PRODUCE CRACKLING, WHICH DEMONSTRATE THEIR EFFECTIVE
AUTHENTICITY. TO CLEAN THE MAJOLICAS, IT IS RECOMMENDED TO
USE A SOFT, DRY CLOTH. IF A DETERGENT OR LIQUID IS USED, THE
LATTER COULD PENETRATE INSIDE THE CRACKLES, HIGHLIGHTING
THEM.
SINCE THE PRODUCT CAN TURN ON AUTOMATICALLY THANKS TO
THE TIMER, OR REMOTELY USING THE DEDICATED APPLICATIONS, IT IS
STRICTLY FORBIDDEN TO LEAVE ANY COMBUSTIBLE OBJECT WITHIN
THE SAFETY DISTANCES INDICATED ON THE TECHNICAL DATA PLATE.
INTERNAL COMBUSTION CHAMBER PARTS CAN BE SUBJECT TO
EXTETICAL WARN, IT DOESN'T AFFECT THE FUNCTIONALITY
routine Maintenance
Based on Decree 22 January 2008 n°37 art.2, routine maintenance means
interventions aimed at reducing degradation due to normal use, as well
as dealing with accidental events entailing the need of rst interventions,
which however do not modify the structure of the system upon which one
is intervening or its intended use according to the requirements laid down
by the technical standards in force and by the manufacturer's use and main-
tenance manual.

7ENGLISH
INSTALLING INSERTS
When installing inserts, access must be prevented to the internal parts of the appliance and it must not be possible to access live parts during
extraction operations.
Any wiring, for example the power cable or room probe, must be positioned so as not to be damaged during movement of the insert and must
not come into contact with hot parts. If a cavity made of combustible material is installed, we recommend taking all the safety precautions
indicated by the installation standards.
VENTILATION AND AERATION OF INSTALLATION ROOMS
In case of non-airtight heater and/or installation, the ventilation must respect the minimum area indicated below (considering the highest value
among those provided):
Appliance categories Reference standard
Percentage of the
net opening section with respect to the
appliance fumes outlet section
Minimum net opening value of the
ventilation duct
Pellet stoves UNI EN 14785 - 80 cm²
Boilers UNI EN 303-5 50% 100 cm²
INSTALLATION
GENERAL
The ue gas exhaust and hydraulic connections must be carried out by qualied personnel who must issue installation conformity
documentation compliant with national standards.
The installer must provide the owner or person acting for him, according to the legislation in force, with the declaration of conformity,
supplied with:
1) the use and maintenance manual of the appliance and of the system components (such as for example, the smoke ducts, chimney, etc.);
2) photocopy or photograph of the chimney plaque;
3) system booklet (where applicable).
The installer must ask to be issued with a receipt stating that the documentation has been provided, and must keep it with a copy of the technical
documentation relating to the installation.
For installation in a condominium, prior approval from the condominium's administrator must be requested.
Where required, check the exhaust gas emissions after installation. Should a sampling point be installed, it must be airtight.
COMPATIBILITY
Do not install in rooms with a re hazard. It is also forbidden to install it in living areas with the following characteristics:
1. where there are liquid fuel appliances with continuous or discontinuous operation that draw the combustion air into the room in which they
are installed.
2. wheretherearetype B gasappliances intended forheating,withor withoutdomestic hot water productionand inadjacent and communicating
rooms.
3. where the depression measured in situ between the external and internal environment is greater than 4 Pa.
N.B.: Watertight appliances can also be installed in the cases indicated in points 1, 2 and 3 of this paragraph.
INSTALLATIONS IN BATHROOMS, BEDROOMS AND STUDIO FLATS
Installation in bathrooms, bedrooms and studio ats is only allowed for sealed or closed hearth appliances with ducted combustion air taken
from the outside.
oor protection
POSITIONING AND SAFETY DISTANCES
The support surfaces and/or points must have a suitable capacity to bear the overall weight
of the appliance, accessories and coverings. If the oor is made of a combustible material,
we recommend using a non-combustible material to protect the front part from any burnt
material which might fall during routine cleaning operations. The generator must be level
to function properly. The side walls, the rear walls and the oor support surface should be
made of non-combustible material.
One must also bear in mind all laws and national,
regional, provincial and town council regulations in force
in the country in which the appliance has been installed,
as well as the instructions contained in this manual.
Air inlet
Under any condition, including in the presence of extractor hoods and/or of controlled forced ventilation systems, the pressure dierence
between the generator installation rooms and the outside must always be equal to or less than 4 Pa.
MINIMUM DISTANCES PELLET STOVES
Installation next to ammable or heat-sensitive materials is permitted only if the special
safety distances specied on the label at the beginning of the manual (pag.2) are
observed. If the materials are not ammable, you must keep a side and rear distance of at
least 100 mm (without the inserts). For products equipped with rear spacers, wall-mounting
installation is permitted exclusively for the rear side.
PREPARATIONS FOR MAINTENANCE
To carry out extraordinary maintenance operations on the product, it may be necessary to move it away from the adjacent walls. This must be
done by a technician authorised to disconnect the combustion product evacuation ducts and then reconnect them. For heaters connected to the
hydraulic system, the connection between the system itself and the product must be made in such a way that, when an authorised technician is
about to carry out extraordinary maintenance operations, it is possible to move the heater at least 1 metre away from the adjacent walls.

3 - 5%
Max 3 mt
8ENGLISH
EXAMPLES OF CORRECT CONNECTION TO THE CHIMNEY
In the presence of type B gas appliances with intermittent operation not intended for heating, they must have their own aeration and/or
ventilation opening.
The air inlets must meet the following requirements:
they must be protected with grids, metal mesh, etc., but without reducing the net useful section;
they must be made so as to make the maintenance operations possible;
positioned so that they cannot be obstructed;
The clean and non-contaminated air ow can also be obtained from a room adjacent to that of installation (indirect aeration and
ventilation), as long as the ow takes place freely through permanent openings communicating with the outside.
The adjacent room cannot be used as a garage, or to store combustible material or for any other activity with a re hazard, bathroom,
bedroom or common room of the building.
FLUE GAS EXHAUST
The heat generator works in depression and is equipped with an outlet fan for ue gas extraction. There must be a single exhaust system for
the generator. Using a ue that is shared with other devices is not allowed.
The components of the ue gas exhaust system must be chosen in relation to the type of appliance to be installed in compliance with:
UNI/ TS 11278 in the event of metal chimneys, with particular attention to that stated in the specication;
UNI EN 13063-1 and UNI EN 13063-2, UNI EN 1457, UNI EN 1806 in the event of non-metallic chimneys.
The length of the horizontal section must be minimal and, in any case, no longer than 3 metres, with a minimum upward slope of 3%
There must not be more than 4 direction changes including the one due to the use of the "T" element.
A“T” tting with a condensation collection cap must be provided at the base of the vertical section.
If the exhaust is not inserted in an existing ue, a vertical section with a windproof end piece is required (UNI 10683).
The vertical duct can be inside or outside the building. If the smoke duct is inserted in an existing ue, it must be certied for solid fuel.
If the smoke duct is outside the building, it must always be insulated.
The smoke ducts must have at least one airtight inlet for ue gas sampling.
All the sections of the ue gas duct must be accessible to inspection.
Inspection openings must be provided for cleaning.
If the generator has a fume temperature lower than 160°C+ ambient temperature caused by the high yield (contact technicians) it
MUST be resistant to humidity.
A ue system that does not respect the previous points or, in general, that does not comply with the regulations, may cause condensation
phenomena inside it.
CHIMNEY CAP
The chimney caps must meet the following requirements:
they must have a useful outlet section no less than double that of the chimney/ducted system on which it is installed;
they must be adapted in order to prevent the penetration of rain and snow in the chimney/ducted system;
they must be built so that, in the event of winds coming from all directions and from any angle, the expulsion of combustion products
is in any case ensured;
Protection from rain
and wind
Condensation-proof
"T" tting with
inspection plug
Insulated ue
Insulated "T"
tting with
inspection plug
Protection from rain and wind
"T" tting with
inspection
plug
CONNECTION TO THE MAINS ELECTRIC SUPPLY
The generator is supplied with an electric power cable to be plugged into a 230V 50 Hz socket, possibly with a circuit breaker switch. The
socket must be easily accessible.
The electrical system must be compliant with standards. The eciency of the earthing circuit must be checked. Unsuitable earthing of the
system can cause malfunctioning for which the manufacturer will not be held liable.
Power supply variations beyond 10% can cause faulty operation of the product.
FOR GERMANY ONLY
The product can be connected to a shared ue (multi-connection) provided that the requirements of the regional and national regulations,
amongst which DIN EN 13384-2, DIN V 18160-1, DIN 18896 and of the MFeuV-2007 (Muster-Feuerungsverordnung) are strictly complied with,
and that the local chimney sweep has checked and approved the installation conditions.
Please also remember the following indications, which the end user must comply with:
• The device can be operated only with the doors closed.
• The doors and all setting devices must remain closed when the device is not on (except for cleaning and maintenance operations).

Max 4 mt
9ENGLISH
installation example
One must also bear in mind all laws and national, regional, provincial and town council regulations in force in the country in which the appliance has been
installed, as well as the instructions contained in this manual.
Max. 1.5 m -
max. 2 elbows
Hermetically sealed installation
The generator is a fully sealed product with respect to the environment in which it is installed. This means that it is ideal for passive houses
because it does not take air in from within the house.
combustion air
To ensure the stove remains hermetically sealed, the connection pipe for the combustion air must be directly connected to the exterior, using
special pipes and sealed connectors.
Fumes exHaust system
• If the generator has a fumes temperature of less than 160°C+ room temperature due to the high performance (refer to technical data),
the fumes exhaust system must be completely waterproof.
• If there is a possibility that fumes may condense, an external inspection hatch must be tted.

A
B
C
E
G
H
I
D
*F
10 ENGLISH
DEtAIls oF ANGIE
AAccess to combustion chamber
and ash drawer ERear fumes exhaust
G
On/O
BPellet hopper pressurised closure
F
Serial input Fuse
CRoom air outlet 230V power supply
Supplementary
thermostat input
DRadio/emergency board HCombustion air inlet

11ENGLISH
NotE For CorrECt FuNCtIoNING
Pellet hopper lid
Fire door
The following indications must be respected for correct pellet
stove functioning:
Both during the functioning and when the stove is not in use,
all the machine doors (pellet hopper, re door, ash drawer) must
always remain closed. The machine doors can only be opened
for the time required to load the pellet and for maintenance.
Failure to comply with that above during operation will cause
the display to show the following:
"CLOSE HOPPERDOOR"
This indication means that you have 60 seconds to close the
hatch/door and the pellet lid.
Once 60 seconds have passed, during ignition the stove will
go into "DEPR ALARM" mode, while during normal operation
the stove will go into "COOLING STANDBY" mode before
automatically restarting when the conditions are satised (cold
stove, etc.).
stovE posItIoNING
For best performance, it is recommended to position the stove in such a way that it is perfectly level, with the aid of a spirit level.
FusE
If the stove is not powered, have the condition of
the fuse checked by a qualied technician.

1. 2. 3.
4. 5. 6.
*
12 ENGLISH
UPPER FUMES OUTLET ASSEMBLY
FOLLOW THE ASSEMBLY INSTRUCTIONS CAREFULLY!
ALWAYS FOLLOW THE ASSEMBLY INSTRUCTIONS IN COMPLETE SAFETY!
THE STOVE MUST BE COMPLETELY COLD, SWITCHED OFF AND DISCONNECTED FROM THE ELECTRICAL POWER SUPPLY.
*NOT AVAILABLE
THE CONVERSION OF THE REAR FLUE gAS OUTLET MUST BE CARRIED OUT BY QUALIFIED PERSONNEL AND/OR THE
MANUFACTURER’S TECHNICIANS
J
*It Is forbIdden to carry out thIs assembly and Install the applIance wIth the upper flue gas outlet
for all uses throughout metropolItan france and Its overseas departments and regIons (drom),
where reference Is madetothe regulatIons of the dta Issued bythe commIssIon responsIble for IssuIng
technIcal assessments (ccfat).

13ENGLISH
PELLETS AND LOADING
Pellets are made by subjecting wood shavings i.e. the rejects of pure unpainted wood from sawmills, carpentry products and products from
other activities connected to wood working and transformation, to very high pressures.
This type of fuel is fully ecological as no glues are used for its compaction. In fact, pellet compactness is guaranteed over time by a natural
substance found in wood: lignin.
In addition to being an ecological fuel, making best use of wood residue, pellets also have a series of technical advantages.
While wood has a caloric value of 4.4 kWh/kg (with 15% moisture, therefore after approximately 18 months of curing), that of pellets is 5
kWh/kg.
Pellet density is about 650 kg/m3and water content is equal to 8% of its weight. For this reason pellets do not need to be cured to obtain a
sucient heat yield.
THE USE OF POOR QUALITY PELLETS OR ANY OTHER MATERIAL WILL COMPROMISE STOVE FUNCTIONS, VOIDING
THE WARRANTY AND RELEASING THE MANUFACTURER OF LIABILITY.
Do not place the bag Directly on the stove to loaD the tank.
always use a scoop to loaD the tank. Do not rub or place weights on the tank seal. keep the tank cover
seal supporting surface clean at all times. check the conDitions of the seal frequently. if DamageD,
contact your local authoriseD technician.
The pellets used must be class A1 certied according to standard
ISO 17225-2 (ENplus-A1, DIN Plus or NF 444 of the following
category: “High quality NF biocombustible wood pellets”).
UNI EN 303-5 with the following characteristics: water content
≤ 12%, ash content ≤ 0.5% and lower caloric value >17 MJ/kg (in
the case of boilers).
The Manufacturer recommends using pellets with a diameter of
6mm with its products.
PELLET STORAGE
To guarantee combustion without problems, the pellets must be
kept in a dry place.
Open the tank lid and load the pellets using a scoop.
PELLET HOPPER
During stove operation, the pellet hopper lid must always be closed.

L2
P1
P2
L1
L6
L4
L5
L3
14 ENGLISH
Radio/emeRgency caRd
The stove is tted with an emergency radio card which allows for basic control of the stove in the event of a fault or if the remote control is
malfunctioning.
The functions that can be managed from the emergency card are:
L1: Yellow LED LED
o: radio communication not available.
LED on: radio communication available.
L4: Yellow LED LED on: 5^ power set (by the user).
L2: Red LED LED o: normal operation.
LED on: alarm present. L5: Yellow LED LED on: 1^ power set (by the user).
L3: Green LED
LED o:: stove o.
LED on: stove on.
LED ashing: stove cleaning cycle under way, alarm,
stand by/cooling waiting/or blackout stand by.
L6: Green LED LED for WI-FI control: See WI-FI chapter
P1 On/O stove.
P2 MIN or MAX power setting.
-

15ENGLISH
BATTERY TYPE AND REPLACEMENT
To insert/replace the batteries, simply remove the battery
protection cover at the back of the radio control device (gure 1).
Insert the batteries according to the symbols imprinted on the
radio control device and on the battery itself.
3 AAA batteries are required for the radio control device to
function.
J
THE REMOTE CONTROL IS ALREADY CONFIGURED WITH A RADIO ID CHANNEL; IF THERE IS ANOTHER STOVE, TO
AVOID INTERFERENCES, A NEW CONFIGURATION MUST BE MADE, BY CHANGING ONE OF THE TWO STOVES.
SOME RADIO FREQUENCY DEVICES E.G. MOBILE PHONES, ETC. MAY CAUSE INTERFERENCE WITH
COMMUNICATION BETWEEN THE RADIO CONTROL DEVICE AND THE STOVE.
Respect the environment!
Used batteries contain metals that are harmful to the environment, and therefore must be disposed of separately in
special containers.
RADIO CONTROL
(gure 1)
RADIO CONTROL DEVICE ROOM PROBE
CALIBRATION
This mode allows calibration of the room temperature detected by
the radio control device (with ventilation active only). For correct
calibration, it is recommended to position the radio control in a
room with constant temperature and wait for at least two hours.
Below nd the calibration procedure:
Access the menu and reach“TECH MENU”.
Set the access key "F4". - "ADJ REMOTE PROBE"
Using the keys
OK
or
OK
adjust the desired room
calibration.
Save and exit with the key
OK
.
CONFIGURATION
RADIO CONTROL DEVICE CODING PROCEDURE:
1. Disconnect the power supply to the stove.
2. Press the keys
OK
and
OK
at the same time until the RADIO ID channel page appears
3. Using the buttons
OK
and
OK
select the new RADIO ID channel (it is possible to select a RADIO ID channel between 0 and 63).
4. Power the stove. Within 10 seconds (the LED on the radio/emergency board will ash) conrm the selected channel by pressing OK on
the remote control.
5. The LED on the emergency module will remain on for 5 seconds to conrm the new conguration.
6. If the conguration was not successful, " " will appear on the display. In this case, repeat the procedure.

2
3
1
4
5
6
7
8
16 ENGLISH
RADIO CONTROL DEVICE FEATURES
1. DISPLAY
2. SET POWER/ scroll through menus / increase - select a setting
3. SET THERMOSTAT room/ scroll through menus / decrease - deselect a setting
4. Back key
5. Key to access MENU and CONFIRM
6. ON/OFF stove or restore from sleep mode.
7. Serial cable input
8. Battery compartment
The radio control is tted with an LCD backlit display. The display remains lit for 5 seconds. After a certain period of time, in order to
minimise battery consumption, the display turns o (sleep mode).
It turns back on after pressing the ON/OFF key (6).
CAUTION!
Do not place the radio control device in direct or indirect contact with water. The radio control device may not work properly in the
presence of humidity or if exposed to water.
FREQUENCY BANDS MAXIMUM POWER TRANSMITTED
868.3 MHz 4 mW ERP
869.85 MHz 4 mW ERP

17ENGLISH
SCREEN IN OPERATION
SCREEN WITH EXTERNAL THERMOSTAT CONNECTED TO THE TERMINAL“TA”
DISPLAY
Display text
Temperature detected in room
Room SET THERMOSTAT set
Power 1-5^ Time
Chrono active
STAND BY
active
Battery low
Display text
Time
Indicates the status of the
contact of the external
additional thermostat
Tangential fan active
Tangential fan active in QUIET mode

18 ENGLISH
GENERAL MENU
KEY FUNCTION
OK
OK
Scroll through parameters
Modify settings
OK
Ignition - switch-o key
KEY FUNCTION
Back - exit key
OK
Access menu key
GENERAL WARNINGS
Advice to follow for the rst start-ups of the product:
During the rst hours of operation, there may be some smoke or
odours, but they are due to the normal“thermal break-in” process.
During this process, the duration of which changes depending on the
product, it is recommended to:
Ventilate the room well
If present, remove any majolica or natural stone parts from the
top part of the product.
Activate the product at the maximum power and temperature
Avoid remaining in the room for a long time
Do not touch the surfaces of the product
Notes:
The process is completed after a few heating/cooling cycles.
For combustion, do not use elements or substances other than those
indicated in the manual.
Before turning on the product, it is necessary to perform the
following checks:
If it is intended to be connected to a hydraulic system, it must
be complete and fully functional and in compliance with the
instructions given in the product manual and with the relevant
regulations in force.
The pellet hopper must be fully loaded
The combustion chamber and the burn pot must be clean
Make sure that the re holder, the ash drawer and the pellet
hopper close hermetically (if present in the hermetic version); they
must be closed and there must be no foreign bodies in the sealing
elements and gaskets.
Check that the power cord is properly connected
The switch (if present) must be set to position“1”.
MODE SET
VENTILATION SET
EASY SETUP SET
CHRONO ENABLING
CHRONO MODE
PRG1
PRG2
SETTINGS DATETIME PRG3
LANGUAGE PRG4
DISPLAY
STAND BY
DELTAT
FIRST LOAD
* STOVE STATUS DEGREES
RESET
* TECHNICIANS ONLY
EASY CONTROL
WIFI
RADIO PROBE
* TECH MENU DEPRESSURE
NOTICE

19ENGLISH
IT IS FORBIDDEN TO USE THE DEVICE WITHOUT A PARTITION A AND FLAME
GUARD B.
REMOVAL WILL COMPROMISE THE SAFETY OF THE PRODUCT AND RESULT IN
THE IMMEDIATE NULLIFICATION OF THE WARRANTY PERIOD.
IN THE EVENT OF WEAR OR DETERIORATION, ASK THE AFTERSALES SERVICE
TO REPLACE THE PART
REPLACEMENT DOES NOT FALL WITHIN THE PRODUCT WARRANTY AS THE
PART IS SUBJECT TO WEAR.
DATE/TIME
This menu allows the date and time to be set.
To set: OK > SETTINGS > DATE/TIME.
LANGUAGE
This menu allows the preferred language to be selected.
The languages available are: Italian - English - German - French - Spanish - Portuguese - Danish - Estonian - Croatian - Slovenian - Dutch -
Polish - Czech.
To set: OK > SETTINGS > LANGUAGE.
DEGREES
This menu allows you to set the desired unit of measurement.
To set: OK > SETTINGS > DEGREES
FIRST IGNITION SETTINGS
After connecting the power cord at the back of the generator, turn the switch (if any) to position (I).
The switch is used to power the heat generator board.
J
NO IGNITION
THE APPLIANCE MAY FAIL TO LIGHT BECAUSE THE AUGER IS EMPTY AND NOT ALWAYS ABLE TO LOAD THE BURN POT
FAST ENOUGH WITH THE PELLETS NEEDED FOR NORMAL IGNITION.
IF THE PROBLEM OCCURS AFTER ONLY A FEW MONTHS OF OPERATION, CHECK THAT THE ROUTINE CLEANING
DESCRIBED IN THE STOVE HANDBOOK HAS BEEN CARRIED OUT CORRECTLY
DO NOT USE ANY TYPE OF FLAMMABLE LIQUIDS FOR IGNITION!
DO NOT ALLOW THE BAG OF PELLETS TO COME INTO CONTACT WITH THE BOILING HOT STOVE DURING THE
FILLING PHASE!
IN THE EVENT OF CONTINUED FAILURE TO LIGHT, CONTACT AN AUTHORISED TECHNICIAN.
AB

20 ENGLISH
IGNITION
Once the previously listed points have been checked, press key
OK
for three seconds to ignite the stove. During ignition, the stove will check
for a ame for a period of 15 minutes. Once the control temperature has been reached, the
stove interrupts the ignition phase and switches to PREPARATION.
The stove is set to MANUAL mode, power 5, by default.
PREPARATION
During the preparation phase, the stove stabilises combustion, increasing it progressively, to then start ventilation and switch to WORK
WORK IN MANUAL MODE
During the work phase, the stove reaches the POWER dened by the user, heating the room using the VENTILATION set by the user.
SETTING IN AUTOMATIC MODE
This mode, by means of the SET THERMOSTAT, allows for the room temperature to be set.
The adjustment is made using buttons 2 and 3, from 7 to 37°C.
The stove controls the room temperature using a probe built into the radio control.
See paragraph MODE for more details.
AUX MODE
If AUX MODE is selected, temperature control is entrusted to the contact of the additional thermostat, thus ignoring the temperature probe
built into the radio control.
If the contact is open (met), the stove operates at the minimum value (or it switches o if STAND BY mode is active).
If the contact is closed (request), the stove works at the set power.
REGULATION OF SET POWER
The POWER has 5 levels of operation, Pressing the key
OK
allows you to view the set power which can be changed using the keys
OK
or
OK
.
Power 1 = minimum level - Power 5 = maximum level.
The change must be conrmed by pressing the key
OK
.
AUTO BLOW
During the work phase, the stove cleans the burn pot at regular intervals with the function called "AUTO BLOW".
When this procedure starts, a message is displayed. During the "AUTO BLOW" procedure, the pellet feed slows down and the fumes motor
increases.
After cleaning, the stove resumes operation in normal conditions.
SWITCHOFF
Press the
OK
key for three seconds.
Once this operation has been performed, the appliance automatically enters the switch-o phase, blocking the pellet feed.
The ue gas exhaust motor and the hot air ow motor will remain on until the stove temperature has dropped below the safety settings.
REIGNITION
The stove can only be re-ignited if the temperature of the exhaust fumes is lower than the preset threshold and the minimum safety time has
passed.
OPERATION AND LOGIC