Extraflame EcoLogica Idro User manual

PELLETS STOVES
Use and maintenance manual
BELLADIVINA
ECOLOGICAIDRO ECO
LOGICA
I. C. MAXI
BABYFIAMMA PREZIOSA
BELLA LUX CONTESSA
I. C. MINI
English

2
Congratulations! You are now the owner of an EXTRA FLAME stove !
The pellet stove EXTRA FLAME is an ideal heating solution. It springs from the most advanced
technology and is manufactured to the highest standards with an up-to-date design, allowing you
to enjoy the fantastic sensation which the heat of a flame can give, in complete safety at all
times.
This manual tells you how to use your stove correctly. Please read it all carefully before using.
IMPORTANT
Ensure that the dealer completes the following box with the details of the authorised specialist
who will help you if you have any problems in using your new pellet stove.
AUTHORISED SPECIALIST
COMPANY
MR./MS.
STREET N.
POSTAL CODE TOWN
PHONE FAX

3
Contents
IMPORTANT ................................................................................................................... 2
1PRECAUTIONS AND SAFETY .......................................................................….... 4
2TECHNICAL SPECIFICATIONS........................................................…..............…... 5
3AIR REQUIRED FOR COMBUSTION..............................................….................…. 11
3.1 External air intake pipe assembly.....................................................................….. 11
4WHAT PELLETS ARE.........................................................................................…. 12
4.1 Pellet storage.......................................................................................…............. 12
5SAFETY DEVICES.................................................................................................. 13
5.1 Warm air distribution fan breakdown ................................................................... 13
5.2 Fume extractor breakdown ................................................................................... 13
5.3 Pellet loading motor breakdown ........................................................................... 13
5.4 Lighting failure..................................................................................................... 13
5.5 Temporary power failure ...................................................................................... 13
5.6 Electrical safety.................................................................................................... 13
5.7 Fume exhaust safety............................................................................................. 13
5.8 Safety for pellet overheating ................................................................................. 13
5.9 Safety plant pressure ( Ecologica Idro)…………………………….............……..…... 13
5.10 Safety water boiling (Ecologica Idro)……...............…………………....……………. 13
6ASSEMBLY & INSTALLATION INSTRUCTIONS.........................................…............ 14
6.1 Assembly............................................................................................................. 14
6.2 Installation ....................................................................................…................... 14
6.3 Fume exhaust....................................................................................................... 15
6.4 Electrical connection............................................................................................. 16
6.5 Canalisation DIVINS PLUS………………………………………………...............…….16
7INSTALLATION I.C. Maxi and Mini ……..………………………………..…...........….17
8CONTROL PANEL……………………………………………………………..............… 23
8.1 Description of control panel alarms………………………………............….………… 24
9USE.............................................................................…................…................. 24
10 LIGHTING......................................................................................……............... 25
11 NORMAL OPERATION – TURNING OFF, REMOTE CONTROL.….................…......... 25
11.1 Normal operation ...............................................................................….…......... 25
11.2 DIVINA PLUS operation………………………………………………............………… 26
11.3 Turning off.................................................................................…....................... 26
11.4 Remote control...........................................................................…....................... 26
12 ROOM THERMOSTAT............................................................................................ 27
12.1 Digital thermostat........................................................................................…...... 27
12.2 Mechanical thermostat (optional)........................................................................... 28
12.2.1 Mechanical thermostat installation (optional).......................................................... 28
12.2.2 Mechanical thermostat operation .......................................................................... 28
12.2.3 Mechanical thermostat operation with energy saving function (Stby)........................ 28
12.2.4 Mechanical thermostat operation for canalis.motor (DIVINA PLUS)……................... 28
12.3 User parameters…………………………………………………………..............……. 30
13 CHRONOTHERMOSTAT……………....................................................................... 31
13.1 “Day/Night” temperature function..................................................................…… 32
13.2 Pellet feeding adjustment…………......................................................................... 32
13.3 Motor parameters for DIVINA PLUS connection ………............…………………..…. 33
13.4 Alarm signalling.................................................................................….......…… 34
14 Operation of the radiofrequency remote control for I.C. Mini…………..............…. 35
15 CLEANING AND MAINTENANCE.....................................................................…. 41
15.1 Cleaning Ecologica,I.C.Maxi, Ecologica IDRO.........................................................42
15.2 Cleaning Bella, Bella Lux, Divina, Contessa,Preziosa, Babyfiamma ……..............…. 44
15.3 Cleaning I.C.Mini................................................................................................. 46
15.4 Chimney connection...........................................................................…............... 46
16 PROBLEMS, CAUSES AND SOLUTIONS................................................................. 47
17 GUARANTEE................................................................……................................. 49
18 QUALITY CONTROL...............................................................……....................... 50
19 APPENDIX…………………………………………………………….…………........…. 51

4
1 PRECAUTIONS AND SAFETY
The stoves manufactured in our works are built
with the maximum dedication to the individual
components so as to protect both the user and
the installer from accidents. The qualified
personnel are therefore advised to pay special
attention to the electrical connections after
every operation on the product, especially with
regard to the stripped part of the wires which
must not protrude in any way from the terminal
block, thereby preventing possible contact with
the live parts of the wire.
Installation must be carried out by qualified
personnel who must issue a declaration of
compliance of the system with good practice
to the purchaser, who shall assume responsi-
bility for the definitive installation and conse-
quent proper operation of the product
installed. Extraflame S.p.A. shall not be
responsible in the event of failure to
observe these precautions.
This instruction manual constitutes an integral
part of the product: ensure that it always
accompanies the appliance, even if passed to
another owner or user or moved to another
installation. If damaged or lost, ask the local
technical service for another copy.
This stove must be used exclusively for the
applications it was expressly designed for.
The manufacturer shall not be responsible
contractually or extra-contractually for any
damage caused to persons, animals or property
by installation, adjustment and maintenance
errors, or by improper use.
After removing the packaging, ensure that the
contents are intact and complete. If this is not
the case, contact the dealer from whom the
appliance was purchased.
Stove maintenance must be carried out at least
once a year, scheduling it sufficiently in
advance with the service centre.
The following safety precautions must be
observed:
The use of the stove by unattended children and
handicapped persons it not recommended.
Do not touch the stove if you are bare-footed or
if parts of your body are wet or damp.
Modifying the safety or adjustment devices
without the manufacturer’s approval or
instructions is forbidden.
Never pull, detach or twist the electric wires
coming out of the boiler even when the electricity
supply is disconnected.
Do not plug or reduce the dimensions of the
aeration apertures of the room in which the
stove is installed.
The aeration openings are indispensable for a
correct combustion.
Never leave the packaging materials within
reach of children or unattended disabled
persons.
ONLY FOR THE MODEL IDRO:
Before installation, we recommend that you
thoroughly wash all the piping in the system to
remove any residues which could affect the
efficiency of the appliance.
During installation, it is necessary to inform
users that:
• If there is any water leakage, they must shut
off the water supply and promptly notify the
technical support service.
• They must periodically check the working
pressure of the plumbing system.
If the stove is not being used for a long period,
users are advised to call the technical
assistance service engineers to carry out at
least the following operations:
• Turn the main switch to position 0
• Close the water cocks of both the heating
and sanitary systems
• Drain the heating and sanitary systems if
there is any risk of freezing
Stove maintenance must be carried out at least
once every year, scheduling it sufficiently in
advance with the service centre.

5
2 TECHNICAL SPECIFICATIONS
All a.m. data are not binding, but valid just as an indication.
The right to make technical modifications for improving the product is reserved.
Height 945 mm. 945 mm.
Width 670 mm. 670 mm.
Depth 670 mm. 670 mm.
Weight 156 Kg. 150 Kg.
Fume exhaust pipe diameter 80 mm. 80 mm.
Max heating volume / m3220 m3
Total power 14,47 kW/h 2,5 - 11 kW/h
Water power 8,5 kW/h / kW/h
Pellet consumption per hour 0,6 - 3,0 Kg/h 0,6 - 2,4 Kg/h
Absorbed electrical power 25 - 190 W 25 - 100 W
Lighting power +280 W +280 W
Power supply 230 V 50 Hz 230 V 50 Hz
Feed box capacity ~30 kg. ~35 kg.
Inlet/outlet water pipe “ 3/4 “ /
EcoLogica Idro Ecologica
EcoLogica
EcoLogica Idro
B
A
B
A
A: FUMES OUTLET PIPE ø 80
B: AIR INTAKE PIPE ø 50
Boiler outlet “3/4
Boiler inlet “3/4

6
TECHNICAL SPECIFICATIONS
All a.m. data are not binding, but valid just as an indication.
The right to make technical modifications for improving the product is reserved.
Height 606 mm. 550 mm.
Width 640 mm. 700 mm.
Depth 717 mm. 450 mm.
Weight 130 Kg. 110 Kg.
Fume exhaust pipe diameter 80 mm. 80 mm.
Max heating volume 190 m3150 m3
Total power 2,5 - 9,4 kW/h 2,5 - 7,5 kW/h
Water power / kW/h / kW/h
Pellet consumption per hour 0,6 - 2,0 Kg/h 0,6 - 1,6 Kg/h
Absorbed electrical power 25 - 100 W 25 - 100 W
Lighting power +280 W +280 W
Power supply 230 V 50 Hz 230 V 50 Hz
Feed box capacity ~ 28 kg. ~ 12 kg.
Inlet/outlet water pipe “ / “ /
I.C. Maxi I.C. Mini
I.C. Mini
WITH PELLET FEEDING KIT
355 141
143
97
143 355 141
1310 (circa)
1109
1029 80
97
606
423***
I.C. Maxi
*** Minimum Height
The detail “ adjustment pipe”
is pre-drilled with 3 holes Ø 8,5 : 90-100.
For other adjustments, drill according to needs.
A: FUMES OUTLET PIPE Ø80
B: AIR INTAKE PIPE Ø 50

7
*** Minimum Height
The detail “ adjustment pipe”
is pre-drilled with 3 holes Ø 9 :
90-100-90.
For other adjustments, drill
according to needs.
A: FUMES OUTLET PIPE ø 80
B: AIR INTAKE PIPE ø 50
A
B
I.C. Maxi

8
TECHNICAL SPECIFICATIONS
All a.m. data are not binding, but valid just as an indication.
the right to make technical modifications for improving the product is reserved.
Height 858 mm. 884 mm.
Width 440 mm. 477 mm.
Depth 470 mm. 446 mm.
Weight 100 Kg. 110 Kg.
Fume exhaust pipe diameter 80 mm. 80 mm.
Max heating volume 100 m3100 m3
Total power 1,7 - 5,1 kW/h 1,7 - 5,1 kW/h
Water power / kW/h / kW/h
Pellet consumption per hour 0,4 - 1,2 Kg/h 0,4 - 1,2 Kg/h
Absorbed electrical power 25 - 100 W 25 - 100 W
Lighting power +280 W +280 W
Power supply 230 V 50 Hz 230 V 50 Hz
Feed box capacity ~ 11 kg. ~ 11 kg.
Inlet/outlet water pipe “ / “ /
BabyFiamma Preziosa
Preziosa
BabyFiamma WALL DRILLING
SKETCH
AIR INTAKE PIPE
FUMES OUTLET PIPE
FUMES OUTLET PIPE ø 80
FUMES OUTLET PIPE ø 50

9
TECHNICAL SPECIFICATIONS
All a.m. data are not binding, but valid just as an indication.
the right to make technical modifications for improving the product is reserved.
Height 1150 mm. 1041 mm. 1150 mm.
Width 610 mm. 520 mm. 610 mm.
Depth 576 mm. 513 mm. 576 mm.
Weight 170 Kg. 130 Kg. 170 Kg.
Fume exhaust pipe diameter 80 mm. 80 mm. 80 mm.
Max heating volume 220 m3150 m3220 m3
Total power 2,5 - 11 kW/h 2,5 - 7,5 kW/h 2,5 - 11 kW/h
Water power / kW/h / kW/h / kW/h
Pellet consumption per hour 0,6 - 2,4 Kg/h 0,6 - 1,6 Kg/h 0,6 - 2,4 Kg/h
Absorbed electrical power 25 - 100 W 25 - 100 W 75 - 210 W
Lighting power +280 W +280 W +280 W
Power supply 230 V 50 Hz 230 V 50 Hz 230 V 50 Hz
Feed box capacity ~ 30 kg. ~ 25 kg. ~ 30 kg.
Inlet/outlet water pipe “ / “ / “ /
Divina Bella Divina Plus
Divina Bella Divina Plus
A: FUMES OUTLET PIPE ø 80
B: AIR INTAKE PIPE ø 50
A
B
A
B
A
B
A: FUMES OUTLET PIPE ø 80
B: AIR INTAKE PIPE ø 50
A: FUMES OUTLET PIPE ø 80
B: AIR INTAKE PIPE ø 50
C: CANALISATION PIPE ø 80

10
TECHNICAL SPECIFICATIONS
All a.m. data are not binding, but valid just as an indication.
the right to make technical modifications for improving the product is reserved.
Height 1041 mm. 1068 mm.
Width 520 mm. 522 mm.
Depth 513 mm. 500 mm.
Weight 130 Kg. 150 Kg.
Fume exhaust pipe diameter 80 mm. 80 mm.
Max heating volume 150 m3180 m3
Total power 2,5 - 7,5 kW/h 2,5 - 9,4 kW/h
Water power / kW/h / kW/h
Pellet consumption per hour 0,6 - 1,6 Kg/h 0,6 - 2,0 Kg/h
Absorbed electrical power 25 - 100 W 25 - 100 W
Lighting power +280 W +280 W
Power supply 230 V 50 Hz 230 V 50 Hz
Feed box capacity ~ 25 kg. ~ 25 kg.
Inlet/outlet water pipe “ / “ /
Bella Lux Contessa
Bella Lux Contessa
A: FUMES OUTLET PIPE Ø80
B: AIR INTAKE PIPE Ø 50 A: FUMES OUTLET PIPE Ø80
B: AIR INTAKE PIPE Ø 50

11
Combustion always requires air (oxygen). Stoves therefore remove air from the room they are
installed in and this must be replaced.
Bad combustion can be caused by poor air circulation in the house and this is often the case
in modern homes, which have sealed windows and doors. On the other hand, there are also
problems when there are draughts in the room (caused for example by kitchen or bathroom
ventilators). To prevent this type of problem, we suggest a permanent ventilation grill to be
fitted in a window or near the stove. Alternatively, the air can be taken directly from the
exterior or from another sufficiently aerated room (a cellar, for example) by means of a steel
pipe with a diameter of 48 mm.
3.1 External air intake pipe assembly
a) Measure and make a hole with a minimum diameter of 5 cm. in the wall for the intake
pipe (see drawing here below).
b) Connect the stove with the exterior by means of a steel pipe.
ATTENTION!
• Only use steel pipes.
•Pipes in synthetic materials or aluminium must not be used.
•To ensure sufficient air intake, the pipe must not be longer than 2 m. and must not have
too many bends.
•If the pipe leads outdoors, it must end with a 90º downward bend and be protected
against the wind (see Fig. Here below).
3 AIR REQUIRED FOR COMBUSTION
11

12
The pellets are made by applying very high
pressure to sawdust, that is pure timber waste
(without paint), produced by sawmills, carpentry
works and other activities associated with the
working and transformation of timber.
This type of fuel is completely environmentally
friendly as no binders of any kind are used to
keep it compact. In fact, the compactness of the
pellets over time is guaranteed by a natural
substance found in the wood itself: the lignite.
As well as being environmentally friendly, as the
wood residues are exploited to the maximum,
pellets also have technical advantages.
While wood has a calorific power of 4.4
kW/kg. (with 15% humidity, after about 18
months seasoning) the power of pellets is 5.3
kW/kg. The density of the pellet is 650 Kg/m3
and the water content is 8% of its weight.
For this reason, the pellets do not need to be
seasoned to obtain an adequate caloric yield.
Their diameter ranges from a minimum of 5
mm to a maximum of 8 mm.
4.1 Pellet storage
To guarantee problem-free combustion, the
pellet must be stored in a dry place.
WARNING
THE USE OF POOR QUALITY PELLETS OR OF
ANY OTHER MATERIAL DAMAGES THE
FUNCTIONS OF YOUR STOVE AND MAY
LEAD TO THE INVALIDATION OF THE WAR-
RANTY
AND ASSOCIATED RESPONSIBILITIES
OF THE MANUFACTURER.
4 WHAT ARE PELLETS ?

13
5.1 Warm air distribution fan breakdown:
If the fan stops for any reason, the stove stops automatically to prevent overheating.
5.2 Fume extractor breakdown:
If the extractor stops, the electronic unit immediately blocks the supply of pellets.
5.3 Pellet feeding motor breakdown:
If the motor stops, the stove continues to operate until the minimum cooling level is reached.
5.4 Lighting failure:
If no flame develops during the lighting stage, the stove automatically makes another attempt to
light and if no flame comes this time either, the stove will show on the display “ NO ACC”.
While attempting to light the stove , on the display you will read “ATTE” which means “WAIT”.
This function remembers that before lighting the stove , you must be sure that the burning pot,
must be completely free and clean.
5.5 Temporary power failure:
The appliance will re-light automatically after a brief power failure. There may be a minimum
quantity of smoke inside the house when there is no power for a period of 3 to 5 minutes.
THIS DOES NOT GIVE RISE TO ANY SAFETY RISK.
5.6 Electrical safety:
The stove is protected against violent power swings by a master fuse on the rear of the stove
(delayed 2A 250V).
5.7 Fume exhaust safety
An electronic pressure switch stops the loading screw in case the exhaust pipe is obstructed, or
in case the door remains opened for some minutes.
5.8 Safety for pellets overheating
In case of overheating inside the pellet hopper, this safety device stops the functioning of the stove,
the resetting is manual and must be done by a qualified technician.
ONLY FOR ECOLOGICA IDRO:
5.9 Plant pressure safety
A mechanical pressure sensor stops automatically eventually overpressure of the plant. The resetting
of this safety is manual and must be done by a qualified technician.
5.10 Safety for water boiling
In case of water shortage or a minimum water quantity, this safety stops the pellet feeding.
The resetting is manual and must be done by a qualified technician.
5 SAFETY DEVICES

14
6.1 Assembly
An authorised dealer should assemble the
stove.
The assembling of the ceramics in the stoves
which have majolica tiles, must be done by a
qualified technician.
6.2 Installation
a) Paying attention to the dimes of perforation
and taking into consideration a floor pro-
tection plate, if fitted, measure and make
the hole in the chimney for connecting the
fume exhaust pipe with diam. 80 mm.
If the hole has to be done on a wood wall,
the minimum hole diam. must be 130 mm.,
and a min. 20 mm. thickness insulation
material.
b) Connect the stove to the chimney by means
of a steel pipe, sealing it hermetically and
taking care not to obstruct the free section
with the fume pipe. (See fig. 1)
TABLE A: Dimensions of the floor protection
plate and relative safety distances in mm.
6 ASSEMBLY AND INSTALLATION INSTRUCTIONS
REFERENCES Flammable Not-flammable
objects objects
a* 200 100
b* 800 400
c* 200 100
PRECAUTIONS
1. The appliance must be placed on a flame
resistant floor.
If it is placed on a flammable floor, a floor protection plate must be used. (See table A)
2. The appliance must be connected to a chimney authorised for solid fuels with a minimum
diameter of 130 mm.
3. The fume exhaust system is based on the depression (draught) in the place of combustion
and a light fume exhaust over-pressure (forced exhaust). This makes it essential for the
exhaust pipe to be installed correctly and hermetically.
4. To seal and insulate the pipes, only use heat-resistant materials (up to 300 °C) such as
adhesive tape in aluminium, rock wool or high-temperature silicone.
5. The stove must be placed, so that the electric cord is easy to reach.
fig. 1
fig. 2
*see fig. 4

15
6.3 Fume exhaust
In conformity with DPR 412 and UNI
7129-2001, the allowed installations are:
WITH VERTICAL EXTERNAL OR INTERNAL
FLUE
•The Fig. 3 represents the best solution for
discharging the fumes above the roof.
Proceed as in previous chapter with the
installation of a T-fitting with an inspection
plug. The external or internal flue must
be properly fixed and provided with a
chimney pot for protection from rain.
FUME DISCHARGE THROUGH A CHIMNEY
•Fig. 4 is the classic masonry chimney
system, of course in addition to Fig.1).
Use a T-pipe with an inspection plug and
suitable supporting staffs.
If the chimney is too big, we recommend
reducing it by inserting a porcelain steel
pipe or stainless steel (inox), with a
maximum diameter of 150 mm, and
appropriately sealing the fume inlet and
outlet parts of the fume exhaust from the
part in masonry. fig. 4
fig. 3
INTERIOR EXTERIOR
Inspection
Air
intake
Protection from rain
Cover
plate
Airtight sealed
steel plate
Inspection

16
If the fume flue is installed in a fixed way , inspections should be provided for internal
cleaning purposes (ashes), especially in the horizontal sections.
NOTE:
ALL SECTIONS OF THE FUME FLUE MUST
BE EASY TO INSPECT AND TO REMOVE
TO ALLOW THE INTERNAL CLEANING.
( SEE •)
(SEE FIG. 4 AND 5)
6.4 Electrical connections
The stove is supplied with a power cable
which must be connected to a 230 V /50
Hz socket.
The power absorption is indicated in
chapter 2 (technical specifications).
Make sure that the cable does not come
into contact with the hot surfaces of the
stove.
6.5 CANALISATION DIVINA PLUS
The model DIVINA PLUS is equipped with 2 pipes situated on the back of the stove which
allow the canalisation of the heat issued by the stove. As you can see in the photo here below,
we suggest to make the canalisation by using pipes with the following characteristics:
• Internal diameter 80 mm
• Insulated pipes, that is thermal insulation
• The pipe connection to each nozzle , must not be longer than 2 mt.
fig. 5
Inspection
Inspection
Slope
Height over
Inspection
MAX PIPE LENGTH
2 MT MAX PIPE LENGTH
2 MT
INSULATING
MATERIAL

17
7 INSTALLATION I.C.MAXI and I.C. MINI
The Comfort insert is supplied with a sliding base in
iron which allows it to be installed in a pre-existing
fireplace.
This sliding base allows you to slide out the insert
easily for maintenance and cleaning at the end of
the year.
If you do not already have an existing fireplace you
can build one using the insert support pedestal as
its function is to fix the insert to the floor.
Description of the components:
• Sliding base
• Rail
• Fume outlet pipe
• Primary air intake pipe
• Power plug
• Frame
Fitting the Comfort Maxi and Mini with sliding base
Take the sliding base and place it in the pre-existing
fireplace.
Using chalk, mark the base fixing holes on the floor
of the fireplace.
Make the holes for 8 mm steel expansion plugs.
Make a 60 mm hole in correspondence with the air
intake.
N.B. The air intake must be made outside the fire-
place, because it must not draw in overheated air.
In case, it is not possible to take air from outside, it
is possible to use air from inside, fitting a steel pipe
Ø50 mm on the bottom or on the rear of the air
intake box , vacuuming the air outside the chimney.
N.B. The length of the primary air intake pipe
must not exceed 2 metres. There must be sufficient
air circulation in the indoor environment.
Provide a power socket on the rear of the insert, in
order to reach the plug easily once the installation
is made.
Fix the base by means of the fixing screws.
Make the connection to the fume outlet and air
intake, respecting the points described in paragraph
6.
Take the insert, tilt it as in fig. 8 so that the wheels
go into the provided rails, and slide it until the fume
scroll coupling is completely inserted in the fume
conveyor box.
fig. 7
fig. 8
fig. 6

18
18
fig. 11
Finally, using the provided socket wrench, turn the
screw anticlockwise as shown in figure 11.
In order to see if the insert is correctly coupled with
the base, connect the plug to the power socket: the
display should switch on.
N.B. The bottom grill of the insert must stand at
least 1 cm above the marble fire top of the facing.
Installation with pedestal (optional)
Description of components:
•Comfort maxi and Mini insert (see previous
paragraph)
•Pedestal adjustable in height
•Lateral feeding hopper
•Adjustable hopper support
Installation of Comfort Maxi and Mini with
pedestal
Position the base in the desired point and adjust to
the desired height by means of the feet (the bolts
are located in the four external sides of the pedestal
at the bottom).
Provide a power socket in the rear of the pedestal,
easy to reach once the installation is finished.
Fix the pedestal to the floor using strong steel plugs,
diam. 8 mm.
Take the sliding base and fix it to the frame using
the bolts.
Connect the fume outlet and air intake as explained
in the previous paragraph.
Take the insert, tilt it as in fig. 8 so that the wheels
go into the provided rails, slide it until the fume
scroll coupling is completely inserted in the fume
conveyor box.(Fig.9)
Finally, using the provided socket wrench turn the
screw anticlockwise as shown in figure 11 (for
Comfort Maxi) and as shown in Fig. 11bis (for
Comfort Mini).
In order to see if the insert is correctly coupled with
the base, connect the plug to the power socket: the
display should go on.
Fit the hopper support as shown in fig. 10.
Insert the support in the provided coupling as
shown in fig. 10.
N.B.: In case you use our pedestal, it is necessary
to create an inspection window in the chimney,
allowing to check the pellet level in the hopper,
while filling it up.
fig. 10
fig. 9

19
N.B. The hopper support can be fitted on both
sides of the insert Comfort Maxi while for the
Comfort Mini it can be fitted only on the right side.
Adjust the height and angle of the hopper on the
basis of the fireplace which has to be built.
N.B. The bottom grill of the insert must stand at
least 1 cm above the marble fire top of the facing.
Extraction of Comfort Maxi and Mini
The extraction of the Comfort insert is necessary to
carry out ordinary maintenance (cleaning the ash
pipe at the end of the year) or extraordinary work
(replacement of mechanical parts in the event of
damage).
These operations must be carried out by a qualified
technician, with the insert turned off and the plug
disconnected.
To extract the insert, carry out the following procedure:
1. Take the provided socket wrench and insert it on
the screw at bottom right – Fig. 11 (Maxi) and
Fig.11bis (Mini)
2. Turn the wrench clockwise.
3. Insert the provided pokers in the curved part as
shown in fig. 12.
4. Pull the insert towards you until it is blocked
automatically.
5. Remove the two top screws which fix the lateral
side to the insert, Fig.13 (Maxi)
For the insert Mini, it is necessary first to remove
the insert from its base and then remove the
screws.
6. Release the side, put your hand on the bottom
part and press slightly upwards until it uncouples
(Fig. 14).
Frames fitting
• Frontal frame
• Lateral frames
Fix the frontal frame with both the lateral frames in
such a way as to create the figure as shown in Fig.
15.
Fix the frames to the Comfort insert by means of
self-piercing screws.
N.B. Any wooden beams situated above the insert
must be protected using fireproofing material.
Assembly of the frames is important as it allows a
correct air circulation in the insert and consequently
a very good operation of the stove.
fig. 13
19
fig. 11 bis
fig. 12

20
20
Air circulation ducts
It is necessary to create air intakes on the top of the
fireplace for a correct operation.
These can be made in the sides of the hood or in
the front.
It is important that following measurements are
respected:
Air intakes made in both sides of the fireplace
Minimum measurement requested 200 cm2 x side
Air intake made in the front of the fireplace
Minimum measurement requested 400 cm2 x side
The position of the air intakes is shown in Fig. 17
Also in the bottom part of the chimney an air intake
must be created ( for the min. measures see Fig.17)
fig. 14
fig. 15 fig. 16
FIXING SIDE SURROUNDS WITH
TOP SURROUND BY MEANS OF
TWO SCREWS PER SIDE
USE THESE HOLES FOR
FIXING THE SIDE
SURROUNDS ONTO
THE SIDES
WASHER
SCREW
SECT A-A