Extraflame COMFORT P85 User manual

MADE IN ITALY
design & production
INSERTO COMFORT P85 - P85 PLUS
004277958 - Rev 000
UK PELLET STOvES USER MANUAL

2ENGLISH

3ENGLISH
ENGLISH............................................................................................................................................................................................................ 4
WarNINGS........................................................................................................................................................................................................ 4
SafEty.............................................................................................................................................................................................................. 4
routINE MaINtENaNcE................................................................................................................................................................................ 6
INStaLLatIoN.................................................................................................................................................................................................. 7
MINIMUM DISTANCES..............................................................................................................................................................................................................................7
PREPARATIONS FOR MAINTENANCE..................................................................................................................................................................................................7
DEtaILS of coMfort P85 INSErt................................................................................................................................................................ 9
DEtaILS of coMfort P85 PLuS INSErt.................................................................................................................................................... 10
INStaLLatIoN of coMfort P85 - P85 PLuS INSErt............................................................................................................................... 11
GENERAl......................................................................................................................................................................................................................................................11
MINIMUM ClEARANCE ..........................................................................................................................................................................................................................11
INSTAllATION ...........................................................................................................................................................................................................................................12
frESH aIr DuctS .......................................................................................................................................................................................... 14
EXISTING INSTAllATION.......................................................................................................................................................................................................................14
NEw INSTAllATION ................................................................................................................................................................................................................................15
SafEty LatcH................................................................................................................................................................................................ 16
ExtractIoN of INSErt aND PELLEt LoaDING ....................................................................................................................................... 17
PELLEtS aND fEEDING ................................................................................................................................................................................. 17
oPtIoNaL LoaDING accESSorIES ............................................................................................................................................................ 18
FRONT PEllET lOADING kIT...............................................................................................................................................................................................................18
UPPER/SIDE PEllET lOADING kIT ....................................................................................................................................................................................................18
buLb tHErMoStat rEarM.......................................................................................................................................................................... 18
fuSE ................................................................................................................................................................................................................ 18
aIr DuctING fEaturES INSErt P85 PLuS ................................................................................................................................................ 19
FACTORy DEFAUlT OPERATION IN AIR DUCTING MODE.........................................................................................................................................................19
OPERATION IN AIR DUCTING wITh ThERMOSTAT OR PRObE (OPTIONAl)......................................................................................................................19
ta aDDItIoNaL tHErMoStat (oPtIoNaL)............................................................................................................................................... 20
EMErGENcy MoDuLE................................................................................................................................................................................... 21
raDIo coNtroL............................................................................................................................................................................................ 22
CONFIGURATION......................................................................................................................................................................................................................................22
RADIO CONTROl ROOM PRObE CAlIbRATION ...........................................................................................................................................................................22
bATTERy TyPE AND REPlACEMENT.................................................................................................................................................................................................22
raDIo coNtroL fEaturES......................................................................................................................................................................... 23
DISPLay .......................................................................................................................................................................................................... 24
GENEraL MENu ............................................................................................................................................................................................. 25
bASIC INSTRUCTIONS ............................................................................................................................................................................................................................26
fIrSt IGNItIoN SEttINGS............................................................................................................................................................................ 26
DATE/TIME ..................................................................................................................................................................................................................................................26
lANGUAGE..................................................................................................................................................................................................................................................26
DEGREES ......................................................................................................................................................................................................................................................26
oPEratIoN aND LoGIc................................................................................................................................................................................ 27
froNt aIr ...................................................................................................................................................................................................... 28
aIr DuctING 1 ............................................................................................................................................................................................... 28
aIr DuctING 2 ............................................................................................................................................................................................... 28
EaSy SEtuP.................................................................................................................................................................................................... 28
cHroNo.......................................................................................................................................................................................................... 28
ENAblING....................................................................................................................................................................................................................................................29
PRG 1-4 .........................................................................................................................................................................................................................................................29
SEttINGS ........................................................................................................................................................................................................ 31
UPDATE.........................................................................................................................................................................................................................................................31
STAND by.....................................................................................................................................................................................................................................................31
OPERATION wITh ADDITIONAl ThERMOSTAT (OPTIONAl) .................................................................................................................................................31
FIRST lOAD.................................................................................................................................................................................................................................................32
DElTA-T ........................................................................................................................................................................................................................................................32
RESET.............................................................................................................................................................................................................................................................32
aDDItIoNaL fuNctIoNS............................................................................................................................................................................. 32
DElAy SwITCh-OFF.................................................................................................................................................................................................................................32
cLEaNING aND MaINtENaNcE................................................................................................................................................................... 33
MaINtENaNcE............................................................................................................................................................................................... 33
PERIODIC ClEANING UNDER USER'S RESPONSIbIlITy.............................................................................................................................................................33
routINE MaINtENaNcE PErforMED by quaLIfIED tEcHNIcIaNS .................................................................................................... 35
ShUT-DOwN (END OF SEASON)........................................................................................................................................................................................................35
DISPLayS ........................................................................................................................................................................................................ 37
aLarMS .......................................................................................................................................................................................................... 37
GuaraNtEE tErMS ...................................................................................................................................................................................... 38
DISPoSaL........................................................................................................................................................................................................ 39
attENtIoN
SurfacES caN bEcoME VEry Hot!
aLWayS uSE ProtEctIVE GLoVES!
During combustion, thermal energy is released that signicantly increases the heat of surfaces, doors, handles, controls, glass, exhaust
pipes, and even the front of the appliance. Avoid contact with those elements if not wearing protective clothing (protective gloves
included). Make sure children are aware of the danger and keep them away from the stove during operation.

4ENGLISH
Warnings
This instructions manual is an integral part of the product: make sure that
it always accompanies the appliance, even if transferred to another owner
or user, or if transferred to another place. If it is damaged or lost, request
another copy from the area technician. This product is intended for the
use for which it has been expressly designed. The manufacturer is exempt
from any liability, contractual and extracontractual, for injury/damage
caused to persons/animals and objects, due to installation, adjustment
and maintenance errors and improper use.
Installation must be performed by qualied sta, which assumes com-
plete responsibility for the denitive installation and consequent good
functioning of the product installed. One must also bear in mind all
laws and national, regional, provincial and town council Standards pre-
sent in the country in which the appliance has been installed, as well as
the instructions contained in this manual.
The Manufacturer cannot be held responsible for the failure to comply
with such precautions.
After removing the packaging, ensure that the content is intact and
complete. Otherwise, contact the dealer where the appliance was pur-
chased.
All electric components that make up the product must be replaced with
original spare parts exclusively by an authorised after-sales centre, thus
guaranteeing correct functioning.
safety
THE APPLIANCE MAY BE USED BY CHILDREN 8 YEARS OF AGE OR
OLDER AND INDIVIDUALS WITH REDUCED PHYSICAL, SENSORY, OR
MENTAL CAPACITIES OR WITHOUT EXPERIENCE OR THE NECESSARY
KNOWLEDGE, PROVIDED THAT THEY ARE SUPERVISED OR HAVE
RECEIVED INSTRUCTIONS ON SAFE USE OF THE APPLIANCE AND
THAT THEY UNDERSTAND THE INHERENT DANGERS.
We thank you for having chosen our company; our product is a great heating solution developed from the
most advanced technology with top quality machining and modern design, aimed at making you enjoy the
fantastic sensation that the heat of a ame gives, in complete safety.

5ENGLISH
THE GENERATOR MUST NOT BE USED BY PERSONS INCLUDING
CHILDREN WITH REDUCED PHYSICAL, SENSORY AND MENTAL
CAPACITIES OR WHO ARE UNSKILLED PERSONS, UNLESS THEY ARE
SUPERVISED AND TRAINED REGARDING USE OF THE APPLIANCE BY
A PERSON RESPONSIBLE FOR THEIR SAFETY.
THE CLEANING AND MAINTENANCE REQUIRED BY THE USER MUST
NOT BE PERFORMED BY CHILDREN WITHOUT SUPERVISION.
CHILDREN MUST BE CHECKED TO ENSURE THAT THEY DO NOT PLAY
WITH THE APPLIANCE.
DO NOT TOUCH THE GENERATOR WHEN YOU ARE BAREFOOT OR
WHEN PARTS OF THE BODY ARE WET OR DAMP.
THE SAFETY AND ADJUSTMENT DEVICES MUST NOT BE
MODIFIED WITHOUT THE AUTHORISATION OR INDICATIONS OF THE
MANUFACTURER.
DO NOT PULL, REMOVE, TWIST THE ELECTRICAL CABLES COMING
OUT OF THE PRODUCT EVEN IF IT IS DISCONNECTED FROM THE
MAINS.
IT IS ADVISED TO POSITION THE POWER SUPPLY CABLE SO THAT IT
DOES NOT COME INTO CONTACTWITH HOT PARTS OFTHE APPLIANCE.
THE POWER SUPPLY PLUG MUST BE ACCESSIBLE AFTER
INSTALLATION.
DO NOT CLOSE OR REDUCE THE DIMENSIONS OF THE AIRING VENTS
IN THE PLACE OF INSTALLATION. THE AIRING VENTS ARE ESSENTIAL
FOR CORRECT COMBUSTION.
DO NOT LEAVE THE PACKAGING ELEMENTS WITHIN REACH OF
CHILDREN OR UNASSISTED DISABLED PERSONS.
THE HEARTH DOOR MUST ALWAYS BE CLOSED DURING NORMAL
FUNCTIONING OF THE PRODUCT.
WHEN THE APPLIANCE IS FUNCTIONING AND HOT TO THE TOUCH,
ESPECIALLY ALL EXTERNAL SURFACES, ATTENTION MUST BE PAID
CHECK FOR THE PRESENCE OF ANY OBSTRUCTIONS BEFORE
SWITCHING THE APPLIANCE ON FOLLOWING A PROLONGED PERIOD
OF INACTIVITY.
THE GENERATOR HAS BEEN DESIGNED TO FUNCTION IN ANY
CLIMATIC CONDITION. IN PARTICULARLY ADVERSE CONDITIONS
STRONG WIND, FREEZING SAFETY SYSTEMS MAY INTERVENE

6ENGLISH
THAT SWITCH THE GENERATOR OFF. IF THIS OCCURS, CONTACT THE
TECHNICAL AFTERSALESSERVICEAND ALWAYSDISABLETHE SAFETY
SYSTEMS.
IN THE EVENT THE FLUE CATCHES FIRE, USE SUITABLE SYSTEMS
FOR SUFFOCATING THE FLAMES OR REQUEST HELP FROM THE FIRE
BRIGADE.
THIS APPLIANCE MUST NOT BE USED TO BURN WASTE
DO NOT USE ANY FLAMMABLE LIQUIDS FOR IGNITION
DURING THE FILLING PHASE DO NOT PUT THE BAG OF PELLETS TO
INTO CONTACT WITH THE PRODUCT
THE MAJOLICAS ARE TOP QUALITY ARTISAN PRODUCTS AND
AS SUCH CAN HAVE MICRODOTS, CRACKLES AND CHROMATIC
IMPERFECTIONS. THESE FEATURES HIGHLIGHT THEIR VALUABLE
NATURE. DUE TO THEIR DIFFERENT DILATION COEFFICIENT, THEY
PRODUCE CRACKLING, WHICH DEMONSTRATE THEIR EFFECTIVE
AUTHENTICITY. TO CLEAN THE MAJOLICAS, IT IS RECOMMENDED TO
USE A SOFT, DRY CLOTH. IF A DETERGENT OR LIQUID IS USED, THE
LATTER COULD PENETRATE INSIDE THE CRACKLES, HIGHLIGHTING
THEM.
SINCE THE PRODUCT CAN TURN ON AUTOMATICALLY THANKS TO
THETIMER,OR REMOTELY USINGTHE DEDICATED APPLICATIONS, IT IS
STRICTLY FORBIDDEN TO LEAVE ANY COMBUSTIBLE OBJECT WITHIN
THE SAFETY DISTANCES INDICATED ON THE TECHNICAL DATA PLATE.
routine Maintenance
Based on Decree 22 January 2008 n°37 art.2, routine maintenance means
interventions aimed at reducing degradation due to normal use, as well
as dealing with accidental events entailing the need of rst interventions,
which however do not modify the structure of the system upon which
one is intervening or its intended use according to the requirements laid
down by the technical standards in force and by the manufacturer's use
and maintenance manual.

7ENGLISH
INSTALLING INSERTS
When installing inserts, access must be prevented to the internal parts of the appliance and it must not be possible to access live parts during
extraction operations.
Any wiring, for example the power cable or room probe, must be positioned so as not to be damaged during movement of the insert and must
not come into contact with hot parts. If a cavity made of combustible material is installed, we recommend taking all the safety precautions
indicated by the installation standards.
VENTILATION AND AERATION OF INSTALLATION ROOMS
In case of non-airtight heater and/or installation, the ventilation must respect the minimum area indicated below (considering the highest value
among those provided):
Appliance categories Reference standard
Percentage of the
net opening section with respect to the
appliance fumes outlet section
Minimum net opening value of the
ventilation duct
Pellet stoves UNI EN 14785 - 80 cm²
Boilers UNI EN 303-5 50% 100 cm²
INSTALLATION
GENERAL
The ue gas exhaust and hydraulic connections must be carried out by qualied personnel who must issue installation conformity
documentation compliant with national standards.
The installer must provide the owner or person acting for him, according to the legislation in force, with the declaration of conformity,
supplied with:
1) the use and maintenance manual of the appliance and of the system components (such as for example, the smoke ducts, chimney, etc.);
2) photocopy or photograph of the chimney plaque;
3) system booklet (where applicable).
The installer must ask to be issued with a receipt stating that the documentation has been provided, and must keep it with a copy of the technical
documentation relating to the installation.
For installation in a condominium, prior approval from the condominium's administrator must be requested.
Where required, check the exhaust gas emissions after installation. Should a sampling point be installed, it must be airtight.
COMPATIBILITY
Do not install in rooms with a re hazard. It is also forbidden to install it in living areas with the following characteristics:
1. where there are liquid fuel appliances with continuous or discontinuous operation that draw the combustion air into the room in which they
are installed.
2. wheretherearetypeB gas appliancesintended forheating,withor without domestichot waterproduction and in adjacentand communicating
rooms.
3. where the depression measured in situ between the external and internal environment is greater than 4 Pa.
N.B.: Watertight appliances can also be installed in the cases indicated in points 1, 2 and 3 of this paragraph.
INSTALLATIONS IN BATHROOMS, BEDROOMS AND STUDIO FLATS
Installation in bathrooms, bedrooms and studio ats is only allowed for sealed or closed hearth appliances with ducted combustion air taken
from the outside.
oor protection
POSITIONING AND SAFETY DISTANCES
The support surfaces and/or points must have a suitable capacity to bear the overall weight
of the appliance, accessories and coverings. If the oor is made of a combustible material,
we recommend using a non-combustible material to protect the front part from any burnt
material which might fall during routine cleaning operations. The generator must be level
to function properly. The side walls, the rear walls and the oor support surface should be
made of non-combustible material.
One must also bear in mind all laws and national,
regional, provincial and town council regulations in force
in the country in which the appliance has been installed,
as well as the instructions contained in this manual.
Air inlet
Under any condition, including in the presence of extractor hoods and/or of controlled forced ventilation systems, the pressure dierence
between the generator installation rooms and the outside must always be equal to or less than 4 Pa.
MINIMUM DISTANCES
Installation next to ammable or heat-sensitive materials is permitted only if the special
safety distances specied on the label at the beginning of the manual (pag.2) are
observed. If the materials are not ammable, you must keep a side and rear distance of at
least 100 mm (without the inserts). For products equipped with rear spacers, wall-mounting
installation is permitted exclusively for the rear side.
PREPARATIONS FOR MAINTENANCE
To carry out extraordinary maintenance operations on the product, it may be necessary to move it away from the adjacent walls. This must be
done by a technician authorised to disconnect the combustion product evacuation ducts and then reconnect them. For heaters connected to the
hydraulic system, the connection between the system itself and the product must be made in such a way that, when an authorised technician is
about to carry out extraordinary maintenance operations, it is possible to move the heater at least 1 metre away from the adjacent walls.

3 - 5%
Max 3 mt
8ENGLISH
EXAMPLES OF CORRECT CONNECTION TO THE CHIMNEY
In the presence of type B gas appliances with intermittent operation not intended for heating, they must have their own aeration and/or
ventilation opening.
The air inlets must meet the following requirements:
they must be protected with grids, metal mesh, etc., but without reducing the net useful section;
they must be made so as to make the maintenance operations possible;
positioned so that they cannot be obstructed;
The clean and non-contaminated air ow can also be obtained from a room adjacent to that of installation (indirect aeration and
ventilation), as long as the ow takes place freely through permanent openings communicating with the outside.
The adjacent room cannot be used as a garage, or to store combustible material or for any other activity with a re hazard, bathroom,
bedroom or common room of the building.
FLUE GAS EXHAUST
The heat generator works in depression and is equipped with an outlet fan for ue gas extraction. There must be a single exhaust system for
the generator. Using a ue that is shared with other devices is not allowed.
The components of the ue gas exhaust system must be chosen in relation to the type of appliance to be installed in compliance with:
UNI/ TS 11278 in the event of metal chimneys, with particular attention to that stated in the specication;
UNI EN 13063-1 and UNI EN 13063-2, UNI EN 1457, UNI EN 1806 in the event of non-metallic chimneys.
The length of the horizontal section must be minimal and, in any case, no longer than 3 metres, with a minimum upward slope of 3%
There must not be more than 4 direction changes including the one due to the use of the "T" element.
A“T” tting with a condensation collection cap must be provided at the base of the vertical section.
If the exhaust is not inserted in an existing ue, a vertical section with a windproof end piece is required (UNI 10683).
The vertical duct can be inside or outside the building. If the smoke duct is inserted in an existing ue, it must be certied for solid fuel.
If the smoke duct is outside the building, it must always be insulated.
The smoke ducts must have at least one airtight inlet for ue gas sampling.
All the sections of the ue gas duct must be accessible to inspection.
Inspection openings must be provided for cleaning.
If the generator has a fume temperature lower than 160°C+ ambient temperature caused by the high yield (contact technicians) it
MUST be resistant to humidity.
A ue system that does not respect the previous points or, in general, that does not comply with the regulations, may cause condensation
phenomena inside it.
CHIMNEY CAP
The chimney caps must meet the following requirements:
they must have a useful outlet section no less than double that of the chimney/ducted system on which it is installed;
they must be adapted in order to prevent the penetration of rain and snow in the chimney/ducted system;
they must be built so that, in the event of winds coming from all directions and from any angle, the expulsion of combustion products
is in any case ensured;
Protection from rain
and wind
Condensation-proof
"T" tting with
inspection plug
Insulated ue
Insulated "T"
tting with
inspection plug
Protection from rain and wind
"T" tting with
inspection
plug
CONNECTION TO THE MAINS ELECTRIC SUPPLY
The generator is supplied with an electric power cable to be plugged into a 230V 50 Hz socket, possibly with a circuit breaker switch. The
socket must be easily accessible.
The electrical system must be compliant with standards. The eciency of the earthing circuit must be checked. Unsuitable earthing of the
system can cause malfunctioning for which the manufacturer will not be held liable.
Power supply variations beyond 10% can cause faulty operation of the product.

A
B C
D E
G H
K D
F
I
J
9ENGLISH
DETAILS OF COMFORT P85 INSERT
AAmbient air outlet EPellet hopper ITA inlet
BAccess to combustion chamber
and ash drawer FFuse J230V power supply
CEmergency module GRail KCombustion air inlet
DFumes outlet HBulb thermostat rearm

A
B C
D F
I J
M E
H
KL
E G DG
10 ENGLISH
DETAILS OF COMFORT P85 PLUS INSERT
AAmbient air outlet FPellet hopper KTA inlet
Thermostat connection inlet
BAccess to combustion chamber
and ash drawer GAir ducting Z2 outlet L230V power supply
CEmergency module HFuse MCombustion air inlet
DAir ducting Z1 outlet IRail
EFumes outlet JBulb thermostat rearm

11ENGLISH
INSTALLATION OF COMFORT P85  P85 PLUS INSERT
MINIMUM CLEARANCE
With front loading kit H= 635mm
For the insert to operate correctly, a minimum side and rear space
must be guaranteed, as shown in gure 2; the coatings must be
made of non-ammable material.
gure 1 gure 2
GENERAL
The insert is supplied with a sliding base in iron that allows it to be
installed in a pre-existing chimney.
This sliding base allows the insert to be removed easily to load the
pellets inside the hopper and for any maintenance or cleaning at the
end of the season.
If there is no pre-existing chimney, one can be built using an insert-
holder pedestal (optional kit). In fact, the latter xes the insert to the
ground.
ASSEMBLY: place the base in the chosen point and adjust the feet to
the desired height. Install a socket on the rear of the pedestal in a way
that the plug is accessible once installation has been performed. Fix
the pedestal to the oor using have-duty steel plugs with diameter
of 8mm. Take the sliding base and x it to the pedestal.
Please note: If our pedestal is used, a slot must be created in the ue
pipe to allow the pellet hopper level to be checked, thus avoiding
spillage when it is being topped up.
ASSEMBLY MUST BE CARRIED OUT BY QUALIFIED PERSONNEL!

12 ENGLISH
INSTALLATION
Open the door and release the latch using the poker supplied.
Remove the 6 screws and remove the ue pipe from the base.
Fix the base to the existing ue pipe.
ATTENTION! RESPECT THE 50MM HEIGHT FOR OPENING AND CLOSING THE INSERT CORRECTLY!
1
2
3a

13ENGLISH
Fix the base to the kit if it is a new installation (optional kit).
Block the rails with two screwdrivers and secure the ue pipe to the base with 6 screws.
Close the insert and block the latch.
3b
4
5

14 ENGLISH
FRESH AIR DUCTS
For correct operation, air must be allowed to recirculate inside the structure that covers the insert in order to prevent the appliance from
overheating.
To guarantee this, just realise one or more openings in the lower and upper part of the covering.
The following measurements must be respected:
LOWER PART COLD AIR INLET WITH TOTAL MINIMUM SURFACE 240 CM².
UPPER PART HOT AIR OUTLET WITH TOTAL MINIMUM SURFACE 240 CM².
The possible set-ups which must be respected are indicated below.
EXISTING INSTALLATION
FOR INSTALLATION ON AN EXISTING FLUE PIPE EXAMPLES 2 AND 3, A HOLE
MUST BE MADE ON THE SUPPORT BASE TO GUARANTEE THE CORRECT AIR FLOW.
EXAMPLE 1 EXAMPLE 2 EXAMPLE 3
A
A
B
B
B
B
A
A
C
D
A: Air convection outlet. Minimum section 120cm2.
B: air inlet from room. Minimum section 120cm2.
C: Air convection outlet.
Minimum section 240cm2.
D: air inlet from room.
Minimum section 240cm2.

15ENGLISH
NEW INSTALLATION
EXAMPLE 1 EXAMPLE 2
A
A
B
B
C
D
A: Air convection outlet. Minimum section 120cm2.
B: air inlet from room. Minimum section 120cm2.
C: Air convection outlet. Minimum section 240cm2.
D: air inlet from room. Minimum section 240cm2.
For the insert to operate correctly, a minimum side and rear space of 35 mm must be guaranteed; the coatings must be made of non-
ammable material.
IMPORTANT: ALL THE OPENINGS CREATED FOR THE CORRECT AIR CIRCULATION MUST PREVENT THE ENTRY OF
HAZARDOUS PARTS BY USING SPECIFIC GRILLES, BUT STILL GUARANTEEING THE MINIMUM AIR FLOW REQUIRED.
THE PIPE FOR FUMES OUTLET MUST ALWAYS MAINTAIN A MINIMUM DISTANCE OF 50 MM FROM INFLAMMABLE PARTS.
J
TO SAFEGUARD FROM ANY OVERHEATING, THE INSERT IS SUPPLIED WITH A PROBE THAT ANALYSES THE
TEMPERATURE INSIDE THE STRUCTURE
AND INTERVENES BY REDUCING THE FUNCTIONING POWER.

16 ENGLISH
SAFETY LATCH
Use the poker supplied to perform the release/block operation.
(Turn clockwise to release and anti-clockwise to block).
Holes present on two sides for the extraction of the insert via pokers.
Extraction of the insert allows both the pellets to be loaded inside the hopper and routine maintenance (cleaning the ash pipe at year
end) or unscheduled maintenance (replacement of mechanical parts if the product should break) to be performed.

17ENGLISH
EXTRACTION OF INSERT AND PELLET LOADING
Extraction of the insert allows both the pellets to be loaded inside the hopper and routine maintenance (cleaning the ash pipe at year end) or
unscheduled maintenance (replacement of mechanical parts if the product should break) to be performed.
To extract the insert, follow the procedure below:
Open the re door and turn the latch clockwise (using the poker supplied).
Turn the stove towards you using the pokers supplied until it blocks automatically.
THE INSERT MUST ONLY BE PULLED OUT WHEN THE STOVE IS SWITCHED OFF AND COMPLETELY COLD!
THE SURFACES MAY BE VERY HOT! ALWAYS USE SAFETY GLOVES!
THE USE OF POOR QUALITY PELLETS OR ANY OTHER MATERIAL DAMAGESTHE FUNCTIONS OFYOUR STOVE AND CAN
VOID THE WARRANTY AND THE RELEVANT RESPONSIBILITY OF THE MANUFACTURER.
TO GUARANTEE COMBUSTION WITHOUT PROBLEMS, THE PELLETS MUST BE KEPT IN A DRY PLACE.
PELLETS AND FEEDING
Pellets are made by subjecting wood shavings i.e. the rejects of pure wood (without paint) sawmill, carpenter products and products from
other activities connected to working and transforming wood, to very high pressures.
This type of fuel is fully ecological as no glues are used to hold it together. Indeed, the pellets remain compact over time due to a natural
substance found in wood: lignin.
As well as being an ecological fuel, as wood residues are made the most of, the pellet also has technical advantages.
While wood has a caloric value of 4.4 kWh/kg. (with 15% humidity, thus after 18 months of seasoning), the caloric value of the pellet is 5
kWh/kg.
Pellet density is about 650 kg/m3 and water content is equal to 8% of its weight. For this reason, the pellets do not need to be seasoned in
order to obtain a suciently adequate heat yield.
The pellet used must comply with the features described by Standards:
EN PLUS class A1, ISO 17225-2 class A1
and
UNI EN 303-5 with the following characteristics: Water content ≤ 12%, ash content ≤ 0.5% and heating value less than >17 MJ/kg (for boilers).
The manufacturer recommends using pellets with a diameter of 6 mm with its products.
PELLET STORAGE
To guarantee combustion without problems, the pellets must be kept in a dry place.
Open the hopper lid and load the pellets using a scoop.
DO NOT PLACE THE BAG DIRECTLY ON THE STOVE WHEN LOADING THE HOPPER!
ALWAYS USE A SCOOP TO LOAD THE HOPPER.

18 ENGLISH
J
IN CASE OF INSTALLATION WITH LOADING KIT OPTIONAL THE MACHINE MUST NOT BE REMOVED.
DO NOT LOAD A GREATER NUMBER OF PELLETS THAN THE CAPACITY OF THE HOPPER AND DO NOT DROP PELLETS
INSIDE THE PRODUCT.
Further information on accessories is available on the website under the category "accessories".
BULB THERMOSTAT REARM
The gure below shows the hopper rearm position. It is
recommended to contact the qualied technician if one of the
rearms should be triggered, so as to verify the cause.
FUSE
If the stove has no power supply, check the status of the fuse,
positioned laterally (right) with respect to the machine, located on
the circuit board support.
OPTIONAL LOADING ACCESSORIES
FRONT PELLET LOADING KIT
The optional pellet loading kit allows to load the pellets into the
hopper from the front without having to remove the insert (which
would require the machine to be switched o).
UPPER/SIDE PELLET LOADING KIT
The optional pellet loading kit allows to load the pellets into the
hopper without removing the insert from the installation opening
(which would require the machine to be switched o).
The kit can be assembled at a later time too.

z2 Iz1
19ENGLISH
Features:
diameter of air ducting outlet: 2x80 mm
maximum recommended air ducting length 8 m
temperature controlled air ducting
Speed regulation can be set in 2 modes: AUTO, COMFORT
FACTORy deFAUlT OpeRATiOn in AiR dUCTing MOde
Air ducting 1 and 2 are always in request by factory default (jumpers on Z1 and Z2 present), and follow the stove settings.
- No settings necessary.
OpeRATiOn in AiR dUCTing wiTh TheRMOsTAT OR pRObe (OpTiOnAl)
The stove is tted with two independent motors for air ducting. The connection of an external thermostat or temperature probe (NTC 10K)
in inputs 1 and 2, located in the rear part of the stove, makes it possible to control the air ducting motor independently of the stove.
Suce it to connect the thermostat/temperature probe and set the desired temperature.
For information on air ducting settings see chapter:" Menu - Air ducting"
WITH AMBIENT THERMOSTAT OPTIONAL
Remove the jumper on 1 and connect the ambient thermostat in the room that needs to be temperature-controlled through air ducting 1.
2 control modes:
OPERATION IN AIR DUCTING WITH AMBIENT THERMOSTAT OPTIONAL
seT congured to AUTO
(the temperature setting is not visible)
Oncethespecic activationthresholdhasbeenreachedand exceeded,attemperature
to be satised (CLOSED CONTACT) the air ducting motor will follow the stove settings.
When the temperature set on the thermostat is reached (OPEN CONTACT), the air
ducting motor will switch to minimum and then follow the stove settings again when
there is a new request.
seT congured to COMFORT
(the temperature setting is not visible)
Oncethespecic activationthresholdhasbeenreachedand exceeded,attemperature
to be satised (CLOSED CONTACT) the air ducting motor will follow the stove settings
but at a lower speed than in SET AUTO for increased acoustic/ambient comfort.
When the temperature set on the thermostat is reached (OPEN CONTACT), the air
ducting motor will switch to minimum and then follow the stove settings again, but
at a lower speed when there is a new request.
SAMe OPerAting SettingS FOr Air ducting 2 MOtOr
AiR dUCTing FeATURes inseRT p85 plUs
The model is tted with two independent air ducting outlets. The pipe used for ducting the hot air must have an internal diameter of 80 mm
and it must also be insulated or at least be protected against heat dispersion.
Air ducting 1 - 2 are enabled by factory default.

TA
20 ENGLISH
TA AddiTiOnAl TheRMOsTAT (OpTiOnAl)
The appliance is able to control the room temperature through an additional thermostat (optional).
After ignition (by pressing key 1 or in chrono mode), the stove will work to reach the set value on the thermostat, displaying wORk (closed
contact) on the screen. The room sensor incorporated into the handheld device is automatically ignored,
insTAllATiOn MUsT be peRFORMed by qUAliFied sTAFF And/OR The MAnUFACTUReR's seRviCe TeChniCiAns
TO INSTALL AND ACTIVATE:
A mechanical or digital thermostat is required.
Remove the plug from the socket.
Using the image to the side as a guide, connect the two thermostat wires (clean contact - no 230 V!) to
the respective terminals at the back of the machine, one red and the other black.
Connect the power to the stove again.
Press the key (
OK
), until the set temperature is set to lOw-TA.
The stove is now correctly congured.
It will work by checking the external additional thermostat based on the TA function.
OPERATION IN AIR DUCTING WITH NTC PROBE 10K OPTIONAL
seT congured to AUTO
Set the desired temperature ( from 7 to 37 °C)
Oncethe specic activationthresholdhasbeen reached andexceeded,attemperature
to be satised the air ducting motor will follow the stove settings.
When the temperature set on the set TEMPERATURE is reached, the air ducting motor
will switch to minimum and then follow the stove settings again when there is a new
request.
seT congured to COMFORT
Set the desired temperature ( from 7 to 37 °C)
Oncethe specic activationthresholdhasbeen reached andexceeded,attemperature
to be satised the air ducting motor will follow the stove settings but at a lower speed
than in SET AUTO for increased acoustic/ambient comfort.
When the temperature set on the set TEMPERATURE is reached, the air ducting motor
will switch to minimum and then follow the stove settings again, but at a lower speed
when there is a new request.
SAMe OPerAting SettingS FOr Air ducting 2 MOtOr
WITH PROBE NTC 10K
Remove the jumper on 1 and connect the NTC probe in the room that needs to be temperature-controlled through air ducting 1.
2 control modes: