Extraflame Comfort Maxi User manual

UK
NL
FR
ES
PT
AD
AT
CH
IT
PL
DE
BE
UK
IE
LU
MK
BG
YU
BA
HR
SI
MD
RO
UA
HU
SK
CZ
BY
RU
LP
LV
EE
FI
SE
NO
DK
AL
GR
Rev004_280411_2272575
STOVE AND PELLET INSERTS USER MANUAL

2

3
ENGLISH............................................................... 4
1. WARNINGS ..............................................................4
2. SAFETY.....................................................................4
3. SAFETY DEVICES....................................................5
4. INSTALLATION........................................................5
4.1. INSTALLATIONS ALLOWED..........................................................6
4.2. INSTALLATIONS NOT ALLOWED...............................................6
4.3. CONNECTIONTO THE SMOKE EVACUATION SYSTEM.6
4.3.1. SMOKE CHANNEL OR FITTINGS ...............................6
4.3.2. CHIMNEY OR INDIVIDUAL FLUE...............................7
4.3.3. CHIMNEY CAP.....................................................................8
4.4. CONNECTIONTO EXTERNAL AIR INLETS............................8
4.5. INSULATION, FINISHINGS, COVERING AND SAFETY
RECOMMENDATIONS.................................................................................9
4.6. NATIONAL, REGIONAL, PROVINCIAL AND TOWN
COUNCIL REGULATIONS...........................................................................9
5. INSERTS INSTALLATION.......................................9
5.1. INSERT COMPARTMENT MINIMUM MEASUREMENTS9
5.2. AIR INLETS...........................................................................................10
5.3. AIR CIRCULATION PIPES .............................................................10
5.4. STANDARD ASSEMBLY................................................................11
5.5. FRAMES ASSEMBLY EXCLUDING MODEL P80............11
5.6. INSERT EXTRACTION....................................................................12
6. HOT AIR DUCTING .............................................. 12
6.1. TOSCA PLUS  EMMA PLUS .......................................................12
6.2. ELISIR......................................................................................................12
6.3. COMFORT PLUS...............................................................................12
6.4. GRAZIOSA STEEL/LUX PLUS.....................................................13
7. PELLETS AND FEEDING ..................................... 13
8. PRODUCT FUNCTIONALITY ............................. 14
8.1. CONTROL BOARD...........................................................................14
8.2. DISPLAY ICONS KEY.......................................................................14
9. FUNCTIONING CYCLE ........................................ 15
9.1. BASIC INSTRUCTIONS..................................................................15
9.2. IGNITION..............................................................................................15
9.3. WORK.....................................................................................................15
10. ADDITIONAL THERMOSTAT ............................. 16
10.1. STOVE FUNCTIONING WITH ADDITIONAL EXTERNAL
THERMOSTAT OPTIONAL ...................................................................16
10.2. INSTALLATION .................................................................................16
10.3. ADDITIONAL THERMOSTAT FUNCTIONING FOR
DUCTING MOTOR CONTROL...............................................................16
11. THE REMOTE CONTROL..................................... 16
11.1. REPLACING THE BATTERIES......................................................16
12. SETTINGS MENU ................................................. 17
12.1. SET CLOCK..........................................................................................17
12.2. CHRONO..............................................................................................18
12.2.1.RECOMMENDATIONS..................................................18
12.2.2.PROGRAMMING EXAMPLE.......................................18
12.2.3.CHRONO MENU TABLE ..............................................19
12.3. LANGUAGE.........................................................................................20
12.4. USER.......................................................................................................20
12.4.1.DISPLAY............................................................................... 20
12.4.2.PELLETS............................................................................... 20
12.4.3.STAND  BY......................................................................... 20
12.4.3.1. STAND  BY WITH DIGITAL
THERMOSTAT AS PER STANDARD...............20
12.4.3.2. STBY WITH ADDITIONAL EXTERNAL
THERMOSTAT..........................................................21
12.4.3.3. HOW TO ACTIVATE OR DEACTIVATE
STAND  BY...............................................................21
12.4.4.KEYS LOCKED...................................................................21
12.4.5.V2  FAN............................................................................... 21
12.4.6.ENABLE V2 ......................................................................... 21
13. CLEANING THE UTILITY..................................... 23
14. CLEANING OF THE“T”FITTING FOR ELISIR... 24
15. TECHNICIANYEARLY CLEANING..................... 25
16. DISPLAYS.............................................................. 26
17. ALARMS ................................................................ 27
18. WARRANTY CONDITIONS ................................ 28

WARNINGS
4
WARNINGS1.
Installation must be carried out by qualified staff and/or
manufacturer technical assistance, who must provide the
buyer with a declaration of conformity for the system and
will assume full responsibility for final installation and as a
consequence the correct functioning of the installed product.
It is necessary to bear in mind all laws and national, regional,
provincial and town council Standards present in the country
the appliance has been installed. The manufacturer cannot
be held responsible for the failure to comply with such
precautions.
1.Electric connections: it is therefore recommended that after any
intervention on the product, that authorised sta pay particular
attention to the electric connections, especially the stripped parts
of the wires.These must not escape from the terminal board in any
situation, thus preventing possible contact with the live parts of
the wire.
2. Type of use: this stove must be destined for the use for which it
has been expressly realised.
3. Liability of the manufacturer: The manufacturer is exempt
from any liability, contractual and extracontractual, for injury/
damagecausedtopersons/animalsandobjects, duetoinstallation,
adjustment and maintenance errors and improper use.
4. Check integrity of the product: After the packaging has been
removed, check the integrity and completeness of the contents. If
this does not comply, contact the dealer where the appliance was
purchased.
5. Electric connections: All electric components that make up
the stove must be replaced with original spare parts exclusively
by an authorised after-sales centre, thus guaranteeing correct
functioning.
6. Maintenance:The stove must be serviced at least once a
year, programming it in advance with qualified staff and/or the
manufacturer's technical after-sales assistance. Nota bene: In case
of thermo product or boiler, the product or system venting is
not covered by the warranty.
SAFETY2.
For safety reasons, remember that:
The stove must not be used by persons (including children)
with reduced physical, sensorial and mental capacities or who
are unskilled persons, unless they are supervised and trained
regarding use of the appliance by a person responsible for their
safety.
Children must be controlled to ensure that they do not play
with the appliance.
Do not touch the stove when you are barefoot or when parts
of the body are wet or humid.
The safety and adjustment devices must not be modied
without the authorisation or indications of the manufacturer.
Donotpull,disconnect,twistelectriccables leaving the stove,
even if disconnected from the electric power supply mains.
It is advised to position the power supply cable in a way that
it does not come into contact with hot parts of the appliance.
The power supply plug must be accessible after installation.
Do not close or reduce the dimensions of the airing vents in
the place of installation. The airing vents are indispensable for
correct combustion.
Donotleavethe packagingelements withinreachof children
or unassisted disabled persons.
The hearth door must always be closed during normal
functioning of the product.
When the appliance is functioning and hot to the touch,
especially all external surfaces, attention must be paid
Check for the presence of any obstructions before switching
the appliance on following a prolonged standstill period.
The stove has been designed to function in any climatic
condition (also critical). In particularly adverse conditions (strong
wind, freezing) safety systems may intervene that switch the
stove o. If this occurs, contact the technical after-sales service
and always disable the safety system.
If the ue should catch re, be equipped with suitable
systems for suocating the ames or request help from the re
service.
This appliance must not be used to burn waste
Do not use any inammable liquids for ignition
During the lling phase do not allow the bag of pellets to
come into contact with the product
Themajolicasaretopqualityartisanproductsandassuch
can have micro-dots, crackles and chromatic imperfections.
These features highlight their valuable nature. Due to their
dierent dilation coecient, enamel and majolica produce
crackling, which demonstrate their eective authenticity.
To clean the majolicas, it is recommended to use a soft,
dry cloth. If a detergent or liquid is used, the latter could
penetrate inside the crackles, highlighting the same.

SAFETY DEVICES 5
ENGLISH
SAFETY DEVICES3.
SAFETY DEVICES
Key: * = present,
- = not present
STOVES
INSERTS
Circuit board: intervenes directly by sending the product
into alarm conditions until complete cooling, in the case
of:breakage ofuegas motor,pellet feed motorbreakage,
black out (if more than 10 seconds), no ignition
**
Upper door micro switch (combustion chamber): if the
combustion chamber is opened, the pellet feed motor
functioning is blocked (*in some models)
*_
Insert blockingmicroswitch: if the end run micro switch
warns that the insert is not blocked, electric energy does
not pass to power it
-*
Flow sensor: in the case of inadequate depression, it
takes the machine to alarm conditions **
F2.5 A 250V fuse (stoves): protects the machine from
violent current drops **
85°C calibrated mechanical bulb with manual rearm:
intervenes by blocking fuel feed whenever the pellet tank
t° reaches the limit of 85°C. Rearm must be performed
by qualied sta and/or the manufacturer's technical
after-sales assistance.
**
Pellet feed-box temperature control probe: if the tank
should overheat, the machine modulates automatically in
order to return to normal temperature values (* in some
models)
**
Mechanical air pressure switch: blocks the pellets in
the event of insucient depression (in the models where
envisioned)
**
INSTALLATION4.
The installation must be in compliance with:
UNI 10683 (2005) heat generators fed with wood and
other solid fuels: installation.
The chimneys must be in compliance with:
UNI 9731 (1990) chimneys: classication based on thermal
resistance.
EN 13384-1 (2006) Thermal and uid dynamic calculation
methods.
UNI 7129 point 4.3.3 Fire Department dispositions, local rules
and prescriptions.
UNI 1443 (2005) chimneys: general requisites.
UNI 1457 (2004) chimneys: clay/ceramic ue liners.
GLOSSARY
CLOSED HEARTH APPLIANCE
Heat generator which opening is only allowed through the loading
of the fuel during use.
BIOMASS
Biological material, excluding the material incorporated in
geological formations and transformed into fossils.
BIOFUEL
Fuel produced directly or indirectly by biomass.
CHIMNEY
Vertical pipe with the aim of collecting and expelling the fuel
products coming from only one appliance, at a convenient height
from the ground.
SMOKE CHANNEL OR FITTING
Pipe or connecting element between heat generator appliance
and chimney to evacuate fuel products.
INSULATION
Group of set-ups and materials used to prevent the transmission
of heat through a wall that separates rooms with dierent
temperatures.
CHIMNEY CAP
Device positioned at chimney peak to ease the dispersion of
combustion products into the atmosphere.
CONDENSATE
Liquid products which form when the fuel gas temperature is lower
or equal to the water dew point.
HEAT GENERATORS
Appliance which allows to produce thermal energy (heat) through
the rapid transformation, through combustion, of the chemical
energy of the same fuel.
GATE VALVE
Mechanism for modifying the combustion gas dynamic
resistance.
COMBUSTION PRODUCT EVACUATION SYSTEMS
Flue gas exhaust system independent from the appliance
constituted by a tting or smoke channel, chimney or individual
ue and chimney cap.
FORCED DRAUGHT
Air circulation by means of the fan activated by electric motor.
NATURAL DRAUGHT
Draught which determines in a chimney/ue due to eect of
the volume mass dierence existing between smoke (hot) and
surrounding atmosphere air, without any mechanical intake aid
installed inside it or at its peak.
RADIATION AREA
Area immediately near the hearth in which the heat caused by
combustion is diused, where there must be no combustion
materials .
REFLUX AREA
Area where leaking of the fuel products is veried, from the

INSTALLATION
6
appliance towards the installation room.
The installation must be preceded by checking the chimneys, ues
or unload terminals positioning regarding:
Installation prohibitions
Legal distances
Limitations disposed by local administrative regulations or
particular authority prescriptions.
Conventional limitations deriving from condominium
regulations, constraints or contracts.
INSTALLATIONS ALLOWED4.1.
Only appliances working in a sealed manner with respect to the
room or which do not place the room in depression with respect
to the external environment, can exist or be installed in the room
where the heat generator will be installed.
Appliances for cooking food and relative hoods without extractor
are only allowed in kitchens.
INSTALLATIONS NOT ALLOWED4.2.
In the room where the heat generator will be installed the following
must not pre-exist or be installed:
hoods with extractor
collective type ventilation pipes.
Should these appliances be in adjacent rooms, communicating
with the installation room, the simultaneous use of the heat
generator is forbidden, where a risk exists of one of the two rooms
being placed in depression respect to the other.
CONNECTION TO THE SMOKE4.3.
EVACUATION SYSTEM
UNI 10683 (2005) Standard
SMOKE CHANNEL OR FITTINGS4.3.1.
To mount the smoke channels, non-ammable elements will
have to be used, ideal for resisting combustion products and their
eventual condensing.
The use of exible metal and asbestos cement pipes to connect
the appliances to the ue is forbidden, even for pre-existing smoke
channels.
There must be continuity between the smoke channel and the ue
so that the ue does not lean on the generator. The smoke channels
must not cross rooms where the installation of the combustion
appliances is not allowed.
The mounting of the smoke channels must be carried out in order
to guarantee smoke seal for the appliance functioning conditions,
limit the formation of condensate and avoid it being transported
towards the appliance.
The mounting of horizontal routes must be avoided.
For appliances where ceiling or wall non coaxial discharges respect
to the appliance smoke outlet have to be reached, the direction
changes will have to realised using open elbows not higher than
45° (see gures below).
For the heat generator appliances equipped with electric fan for
expelling fumes, the instructions below must be followed:
45°
<
gure 1
Insulating
product
45°
<
gure 2
Flue
Inspection
The horizontal routes will have to have a minimum upward
slope of 3%
The length of the horizontal route must be minimal and,
however, not longer than 3 metres
The number of direction changes including the one for eect
of using the "T" element must not be more than 4 (if 4 bends
are used, use double wall piping with an internal diameter of 120
mm).
In any case, the smoke channels must seal the fuel and condensing
products and be insulated if they pass externally to the installation
room.
The use of counterslope elements is forbidden.
The smoke channel must allow the recovery of soot or be
brushable.
The smoke channel must have constant section. Any section
changes are only allowed at the ue coupling.
It is forbidden to have other air supply channels and pipes for
plant engineering, especially if over-sized, transit inside the smoke
channels.The mounting of manual draught adjustment devices on
forced draught appliances is forbidden.

INSTALLATION 7
ENGLISH
CHIMNEY OR INDIVIDUAL FLUE4.3.2.
The chimney or individual ue must respond to the following
requisites:
sealthecombustionproducts, be waterproofand adequately
insulated in line with the use conditions;
berealisedwithmaterialswhichresistthe normalmechanical
stresses, heat, action of the fuel products and any condensing;
have mainly vertical progress with deviations from the axis
not higher than 45°;
be adequately distanced from fuel or ammable materials
through air space or opportune insulation;
REFERENCES Inammable
objects
Non-inammable
objects
A 200 mm 100 mm
B 1500 mm 750 mm
C 200 mm 100 mm
have preferably circular internal section: the square or
rectangular sections must have round corners with a radius not
lower than 20 mm;
have constant internal section, free and independent;
have rectangular section with max. ratio between the sides
of 1.5.
It is recommended that the smoke pipe be equipped with a
collection chamber for solid materials and any condensing situated
under the smoke channel inlet, so that it can be easily opened and
inspected from airtight door.
A
S
gure 3 S= oor protection
Minimum
80 cm2
BC
A
gure 4
< 3 m
3 - 5 %
gure 5
Inspection
gure 6
Chimney cap
Flue
pipe
Inspection

INSTALLATION
8
gure 7
External pipe
that is isolated
inspection
< 3 m
45°
45°
gure 8
inspection
Appliance connection to the ue and fuel products evacuation.
The ue must receive the discharge from only one heat generator.
The direct discharge towards closed spaces is forbidden, even with
clear sky.
The direct discharge of the fuel products must be at roof and the
smoke pipe must have the features provided in the "Chimney or
individual ue" section.
CHIMNEY CAP4.3.3.
The chimney cap must comply with the following requisites:
have an internal section equivalent to that of the chimney;
haveusefuloutletsection not lowerthan double the chimney
internal section;
be built in order to avoid rain, snow, foreign bodies
penetrating the chimney and so that, in the event of winds in
any direction and inclination, the discharge of the fuel products
is assured.
be positioned in a way to guarantee an adequate dispersion
and dilution of the combustion products and, however, outside
the reux area in which the formation of counterpressures
occurs. Such area has dierent dimensions and conguration
depending on the covering inclination angle. It is therefore
necessary to adopt the minimum heights indicated in the gure
layouts below.
The chimney cap must not have mechanical intake means.
FLAT ROOF
50 cm
< 5 m > 5 m < 5 m
50 cm
gure 9
SLOPING ROOF
H min
β
>A
<A
>50 cm
Z
Z=REFLUX AREA
gure 10
CHIMNEY CAPS, DISTANCES AND POSITIONING
Roof
inclination
Distance between
the ridge and the
chimney
Minimum chimney height
(measured from outlet)
β A (m) H (m)
15° < 1,85 0.50 m over the ridge
> 1,85 1.00 m from roof
30° < 1,50 0.50 m over the ridge
> 1,50 1.30 m from roof
45° < 1,30 0.50 m over the ridge
> 1,30 2.00 m from roof
60° < 1,20 0.50 m over the ridge
> 1,20 2.60 m from roof
CONNECTION TO EXTERNAL AIR4.4.
INLETS
The appliance must be able to use the necessary air to guarantee
regular functioning through external air inlet. The air inlets must
comply with the following requisites:
have a total free section of at least 80 cm.
mustbe protectedbygrates,metalnet orsuitableprotections
as long as they do not reduce the minimum section stated in
the previous point and positioned in order to avoid them being
obstructed.
If the combustion agent air is withdrawn directly from outside
through a pipe, a downward bend must be mounted outside
or a protection against the wind and no grates or similar must
be positioned, (it is recommended that the air vent always
communicates directly with the installation room even if the air is

INSERTS INSTALLATION 9
ENGLISH
withdrawn from outside through a pipe). The air ow can also be
obtained from an adjacent room, as long as the ow takes place
freely through permanent openings communicating with the
outside.
The adjacent room, with respect to the installation room, must not
be put in depression with respect to the external environment by
means of reverse draught caused by the presence of another used
appliance or intake device in such room.The permanent openings
in the adjacent room must comply with the above-described
requisites. The adjacent room cannot be set up as garage, storage
for combustion material or activity with danger of re.
INSULATION, FINISHINGS,4.5.
COVERING AND SAFETY
RECOMMENDATIONS
The coverings, independently from the materials from which they
are made, must constitute a self-supporting construction with
respect to the heating block and not be in contact with it.
The cross members and nishings in wood or combustion
materials must be positioned outside the hearth radiation area or
adequately insulated.
If coverings in combustion material or sensitive to heat exist in the
space above the generator, an insulating and non combustible
protection diaphragm must be inserted.
Elements in combustible or inammable material like wooden
furniture, curtains, etc., directly exposed to the hearth radiation,
must be positioned at a safe distance. The appliance installation
must guarantee easy access for cleaning the appliance itself,
discharge gas pipe and ue.
NATIONAL, REGIONAL,4.6.
PROVINCIAL AND TOWN COUNCIL
REGULATIONS
It is necessary to bear in mind all laws and national, regional,
provincial and town council Standards present in the country the
appliance has been installed.
INSERTS INSTALLATION5.
The model is supplied with a sliding base in iron, which allows
it to be installed in a pre-existing chimney, allowing it to be
extracted, with the machine o, easily both for feeding pellets
intothe tankand foranymaintenanceor endof seasoncleaning.
If there is no pre-existing ue, one can be built using the insert-
holder pedestal (optional kit); in fact, the latter xes the insert
to the oor.
Image key: primary air (A), combustion gas discharge (B), frame
(C), sliding base (D), ducting (F)
C
A
B
D
Comfort Maxi
gure 11
A
B
D
C
F
Comfort Plus
gure 12
A
B
D
C
Comfort Mini/Mini Chrystal/P80
gure 13
INSERT COMPARTMENT MINIMUM5.1.
MEASUREMENTS
For correct functioning of the insert, during construction of the ue the
measurements between the insert and internal walls of the ue must
be respected. From the clearance measurements of the stove given in
the technical features, it is necessary to consider at least 50 mm of air in
the upper part and on the 2 sides. The ue outlet pipe must always
maintain a minimum distance of 50 mm from inammable parts.
COMFORT/P80
50mm
50 mm 50 mm
gure 14

INSTALLATION
10
COMFORT MAXI
85 mm 85 mm
60 mm
50 mm 50 mm
gure 15
COMFORT PLUS /MINI/CRYSTAL
35 mm 35 mm
60 mm
gure 16
AIR INLETS5.2.
Regarding the air intake box, it is possible to apply the intake pipe
above the base or below depending on requirements.
These operations must be carried out by a qualied technician
and/or the manufacturer's technical after-sales assistance.
COMFORT MAXI - MINI
gure 17
gure 18
COMFORT PLUS
gure 19
gure 20
AIR CIRCULATION PIPES5.3.
It is necessary to create air recirculation inside the structure that
coverstheinsertfor correct functioning.This preventsthe appliance
from over-heating.
To guarantee this, just realise one or more openings in the lower
part and in the upper part of the covering.
The following measurements must be respected:
Lower part (cold air inlet)total minimum surface
including openings of 600 cm.
The openings in the lower part must be realised below the
rest bottom.
Upper part (hot air outlet)total minimum surface

INSTALLATION 11
ENGLISH
including openings of 600 cm.
The openings in the upper part must be realised above the
upper clearance of the insert.
This ventilation system is totally independent from the air
intake for combustion!
COMFORT MAXI - P80
50 mm
A
B
C
gure 21
COMFORT PLUS - MINI - CRYSTAL
86 mm
A
B
C
gure 22
STANDARD ASSEMBLY5.4.
First of all, check the presence of a current socket on the rear of the
insert so that the socket is accessible once installation is completed.
After having evaluated the correct position, the machine body
must be detached in order to x the sliding base: use the supplied
Allen key to turn the lockbolt clockwise (present at the front in
the bottom left or right, depending on the model).
Fix the base using the locking screws.
Connect the conveyor pipe correctly to the piping for evacuation
of combustion products, the air vent box to the relative intake pipe
and in the case of Comfort Plus also the ducting piping.
Re-position the machine body by repeating the operations carried
out previously in the reverse order.
Finally, use the Allen wrench to turn the lockbolt anti-clockwise to
block movement.
To understand whether the insert is correctly attached to the
base, connect the plug to the socket and set the master switch at
position 1: the display should switch on. The lower grate of the
insert must lie at least 1 cm above the re surface in covering
marble.
gure 23
gure 24
FRAMES ASSEMBLY EXCLUDING5.5.
MODEL P80
Front frame
Side frames
Fix the lateral frames using 2 self-threading screws per side, which
are supplied: the right and left sides are already perforated for xing
the two frames.Any wooden beams situated above the insert
must be protected with re-proof material. Frame assembly
is important as it allows correct recirculation of the air and
consequently optimal product functioning.

HOT AIR DUCTING
12
INSERT EXTRACTION5.6.
The extraction of the Comfort allows to load pellets inside the feed-
box and to perform routine maintenance, (cleaning the ash pipe
at the end of the year) or extraordinary maintenance (replacement
of mechanical parts if the product should break). Maintenance
operations must be performed when the insert is o, with
the plug disconnected from the socket and by an authorised
technician and/or the manufacturer's technical after-sales
assistance.
Follow this procedure to extract the insert:
Take the relevant Allen wrench and insert it in the screw (see
previous paragraph).
Turn the wrench anti-clockwise.
Using the relevant re irons, pull the machine towards
yourself until it blocks automatically.
gure 25
HOT AIR DUCTING6.
The pipe destined for ducting the hot air must have an internal
diameter of 80 mm, be insulated and protected from heat loss.
The length must not exceed 2 metres.The relative pipes used
for ducting the hot air must be installed by qualified staff
and/or the manufacturer's after-sales technicians
TOSCA PLUS  EMMA PLUS6.1.
TheTosca Plus also has 2 pipes placed in the rear for ducting hot air.
TheTosca Plus also oers the possibility to decide where to aim the
hot air ow thanks to two gate valves moved by 2 lever positioned
inside the pellet tank, which must be activated via the re irons
supplied (see gures below).
gure 26 gure 27 gure 28
ELISIR6.2.
The“Elisir”model can be ducted at the rear of the machine, laterally
and from above.
gure 29 gure 30
gura 31
COMFORT PLUS6.3.
Attention: for this product it is mandatory to duct the hot air
gure 32
gure 33

PELLETS AND FEEDING 13
ENGLISH
gure 34
GRAZIOSA STEEL/LUX PLUS6.4.
2x
!F
gura 35
F= canalisation
PELLETS AND FEEDING7.
The pellets used must comply with the features
described by the Standard:
Ö-Norm M 7135
DIN plus 51731
UNI CEN/TS 14961
Extraame recommends the use of pellets with a
diameter of 6mm with its products.
WARNINGS!!!
THE USE OF EXPIRED PELLETS OR ANY OTHER
MATERIAL DAMAGES THE FUNCTIONS OF YOUR
STOVE AND CAN DETERMINE THE INVALIDITY OF THE
WARRANTY AND THE ANNEXED RESPONSIBILITY OF
THE MANUFACTURER.
To guarantee combustion without problems, the pellets must be
kept in a dry place.We recommend the use of pellets with diameter
of 6mm with our products. See the images for feeding pellets.
Open the tank lid and load the pellets using a scoop. In the
case of the inserts, only load when the machine is o and
cold, by extracting it from the compartment. In the case of
installation with feeding kit (optional) the machine must not
be extracted.
gure 36
gure 37
gure 38

PRODUCT FUNCTIONALITY
14
PRODUCT FUNCTIONALITY8.
CONTROL BOARD8.1.
D1 D2
P1 P2 P3P4 P5
gure 39
P1 ON/OFF BUTTON
P2 P3 SETTING ROOM TEMPERATURE
P4 P5 REGULATION OF FUNCTIONING POWER
D1  DISPLAY OF THE VARIOUS TEXT MESSAGES
D2  DISPLAY OF THE POWER
DISPLAY ICONS KEY8.2.
It indicates functioning of the fumes motor.
O = fumes motor not working
On = fumes motor working
Flashing = breakdown
It indicates weekly programming functioning
Indicator on = Weekly programming on
Indicator o = Weekly programming o
It indicates functioning of the tangential fan
O = not working
On = working
It indicates the stby function
O = Stby deactivated
On = Stby activated
It indicates functioning of the ducting fan
O = not working/On = working
Flashing = motor at minimum (input in additional heat board
open)
It indicates the communication between remote control and
stove. Every time a key is pressed on the remote control, the
indicator must switch-on. If the indicator is always on, it means
that the communication between remote control and stove is
blocked.*
Additional external thermostat input status
O = open contact
On = closed contact
Indicates the presence of an alarm.
On: indicates the presence of an alarm
O: indicates the absence of alarms
Flashing: indicates the deactivation of the depression sensor.
Additional thermostat input status for ducting motor control (in
the models envisioned)
O = open contact
On = closed contact
It indicates the room T°. status
On = Room T° lower than desired set
O=roomT°higher that set-point set
Feed box probe
O = normal functioning
Flashing = anomaly
Ign-plug
O = ign-plug active
On = ign-plug deactivated
Flashing = Ignition phase

FUNCTIONING CYCLE 15
ENGLISH
FUNCTIONING CYCLE9.
BASIC INSTRUCTIONS9.1.
The following recommendations must be followed the rst times
the stove is ignited:
It is possible that slight odours are produced due to the
drying of the paints and silicones used. Do not remain in the
environment for long periods.
Do not touch the surfaces as they could still be unstable.
Air the room well several times.
The hardening of the surfaces is terminated after several
heating processes.
This appliance must not be used to burn waste.
IGNITION9.2.
ATTENTION!
Removal of the divider jeopardises the safety of the product
and leads to the immediate voiding of the warranty period.
In the event of wear or deterioration request after-sales
assistance for replacement of the part (replacement that is not
under guarantee as the component is subject to wear).
gure 40
ATTENTION!!!
DO NOT USE ANY INFLAMMABLE LIQUIDS FOR
IGNITION
DO NOT ALLOW THE BAG OF PELLETS TO COME INTO
CONTACT WITH THE BOILING HOT STOVE DURING
THE FILLING PHASE
IN THE CASE OF CONTINUOUS NO IGNITION,
CONTACT AN AUTHORISED TECHNICIAN
Before lighting the stove, the following points must be veried:
the feed-box must be full of pellets
the combustion chamber must be clean
the burn pot must be completely free and clean
check the hermetic closure of the re door and the ash
drawer
make sure the power supply cable is connected correctly
thebipolar switchinthe rearrightpartmustbe positioned
on 1
Once the points listed above have been checked, press the P1
key for three seconds to ignite the stove.
Once the stove has been ignited, it will pass to start-up in order to
go to normal conditions and then normal functioning.
WORK9.3.
Once the machine has been ignited, the machine starts to work.
Regulate the desired room temperature using the P2 and P3
keys.
Set the functioning power (from 1 to 5) using the P4 and P5
keys.
ATTENTION!!!
The lid of the pellet container must always be closed. It
must only be opened during the fuel feeding phase.
The bags of pellets must be kept at least 1.5 metres
from the stove.
It is recommended that the feed-box is always half
full.
Make sure the appliance is o before lling the pellet
tank.
The appliance can control the room temperature using a digital
thermostat as per standard (installed in the factory), which can
lower the heating power to minimum when a pre-set temperature
is reached.
Attention: if the temperature setting is “low” (set below the
threshold of 7°C) the stove will always function at minimum. If the
setting is at “hot”(set higher than the threshold of 40°C) the stove
will not modulate, functioning always and only at the power set.
Regarding the ventilation of hot air the stove adjusts itself
automatically. There are two stove functioning modes, which
are dierent on the basis of the Stand- by function. See“Stand
- by”chapter.
The functioning of models with ductable air is the same as
functioning of other models with the addition of a second motor
for ducting. During normal stove functioning, the second fan will
follow the trend of the rst fan. (For management of the second
motor, see the “Additional thermostat functioning for ducting motor
control”chapter.
Stove functioning can also be set with the Stand- by function. See
“Stand - by” chapter.
SWITCHOFF
Press the P1 key for 3 seconds:
When the operation has been performed, the appliance
automatically enters the switch- o phase, blocking the supply of
pellets.
The ue exhaust motor and the hot air ventilation motor will
remain on until the temperature of the stove has dropped
below the factory parameters.

ADDITIONAL THERMOSTAT
16
ADDITIONAL10.
THERMOSTAT
N.B. : Installation must be performed by an authorised technician
It is possible to thermostat a room adjacent to the room where
the stove is positioned: just connect a thermostat following the
procedure described in the next point (it is recommended to
position the optional mechanical thermostat at a height of 1.50m
from the ground).
There are two stove functioning modes, which are dierent on
the basis of the Stand- by function. See“Stand - by”chapter.
STOVE FUNCTIONING WITH10.1.
ADDITIONAL EXTERNAL THERMOSTAT
OPTIONAL
To make the additional external thermostat function, set the
temperature set on LOW by pressing the P2 key several times.
At this point the digital thermostat supplied as per standard
will be excluded and the stove will work, only controlling the
additional external thermostat.
The desired room temperature will be set via the additional
thermostat. After ignition (by pressing the P1 key or via chrono
mode) the stove will work to reach the set set, displaying WORK
(closed contact). When the room temperature has been reached
(open contact) the stove will go to minimum, displaying LOW.
INSTALLATION10.2.
Switch the appliance o using the master switch positioned
on the rear of the stove.
Remove the plug from the socket.
Refer to the electrical layout to connect the two thermostat
cables onto the relative clamps positioned don the rear of the
machine, one is red and the other black (with STBY label).
gure 41
ADDITIONAL THERMOSTAT10.3.
FUNCTIONING FOR DUCTING MOTOR
CONTROL
For models with ducting motor there is also the possibility of
thermostatting the motor itself. The connection of an external
thermostat will allow to control the ducting motor independently
from stove functioning.
At this point just set the desired temperature on the thermostat.
The thermostat will control the functioning of the second motor:
with temperature to be reached (closed contact) the second
motor will follow the trend of the stove
when the temperature has been reached (open contact), it
takes the ducting motor to 1st speed and will be displayed by
the ashing LED relative to the ducting motor .
Two external clamps are envisioned in the Elisir and Comfort Plus
models.The ducting thermostat clamp is that tted with jumper as
per standard. See example drawing.
gure 42
THE REMOTE CONTROL11.
Nota bene: the remote control is an optional for the
“Rosy” and “Preziosa” models.
The heating power, the desired room temperature and the
appliance ignition/switch o, can be adjusted using the
remote control.
S = Indicator light indicating the pressing of every key.
Display keys correspondence with remote control keys
P1 = P3 + P5
P2 = P2
P3 = P3
P4 = P4
P5 = P5
*to switch on the stove, simultaneously press keys 3 and
5 for 1 second; the appliance will automatically enter the
ignition phase. The power can be regulated using keys 4
and 5 and using keys 2 and 3 it is possible to regulate the
desired room temperature. To switch the stove o, press and
hold keys 3 and 5 simultaneously for three seconds.
gure 43
P1
P4
P5
P3
P2
gure 44
REPLACING THE BATTERIES11.1.
gura 45 gura 46

SETTINGS MENU 17
ENGLISH
SETTINGS MENU12.
To enter the menu, press the P5 key for three seconds.
MENU
D1
FUNCTION
SCROLLING TEXT VALUE
SET
CLOCK
DAY MON...SUN Setting the day of the week
HOURS 00...24: Adjustment of the hour
MINUTES :00...59 Adjustment of the minutes
DAY 1...31 Adjustment of the day
MONTH 1...12 Adjustment of the month
YEAR 00...99 Adjustment of the year
SET
CHRONO
ENABLE CHRONO OFF Activation/deactivation of the weekly programmer
START  PRG1 OFF  00:00 Time 1st ignition
STOP  PRG1 OFF  00:00 Time 1st switch-o
MONDAY PRG1 OFF ...SUNDAY PRG1 OFF ON/OFF Ignition/switch-o consents for various days
SET PRG1 07 35 Setting room temperature for the 1st time span
START  PRG2 00:10 OFF  00:00 Time 2nd ignition
STOP  PRG2 00:10 OFF  00:00 Time 2nd switch-o
MONDAY PRG2 OFF ...SUNDAY PRG2 OFF ON/OFF Ignition/switch-o consents for various days
SET PRG2 07 35 Setting room temperature for the 2nd time span
START  PRG3 00:10 OFF  00:00 Time 3rd ignition
STOP  PRG3 00:10 OFF  00:00 Time 3rd switch-o
MONDAY PRG3 OFF ...SUNDAY PRG3 OFF ON/OFF Ignition/switch-o consents for various days
SET PRG3 07 35 Setting room temperature for the 3rd time span
START  PRG4 00:10 OFF  00:00 Time 4th ignition
STOP  PRG4 00:10 OFF  00:00 Time 4th switch-o
MONDAY PRG4 OFF ...SUNDAY PRG4 OFF ON/OFF Ignition/switch-o consents for various days
SET PRG4 07 35 Setting room temperature for the 4th time span
LANGUAGE ITAL  ENGL  DEUT  FRAN  ESPA Selecting the language
USER
DISPLAY 1...20 Selecting display brightness
PELLETS 30...+30 Selecting the percentage of pellet feed
V1FAN 10...+10 Regulation of the front air percentage
STAND  BY OFF  ON Activation or deactivation of the stand-by function
KEYS LOCKED OFF  ON Activation or deactivation of the keys locked function
V2  FAN 10...+10 Regulation of the ducted air percentage
ENABLE V2 ON/OFF Allows to deactivate the ducting motor (only in envisioned
models)
TECHNICIAN The following menu is reserved for the technical after-sales sta
SET CLOCK12.1.
Clock set allows to adjust the time and date
Controls procedure
From the OFF status, press theP5 key for 3 seconds
The stove will showSET CLOCK
Press theP5 key, DAY will be displayed
modify the day by pressing theP2 key or the P3 key, press the P5 key to continue, HOURS will be displayed, modify the value
using the P2 or P3 keys.
adjust the hours, press theP5 key
for the other values continue as indicated by consulting the table below

THE REMOTE CONTROL
18
SET CLOCK
day Mon, Tue, Wed, ...Sun
hours 0...23
minutes 00...59
date 1...31
month 1...12
year 00...99
To go back to selection of the hours, press button P4 again or
escape and conrm using button P1 .
CHRONO12.2.
The chrono allows to program 4 time spans within a day to use
every day of the week.The switch-on and switch-o time can be set
in every time span. along with the days of use of the programmed
time span and the desired temperature.
RECOMMENDATIONS12.2.1.
The ignition and switch-o times must be within the arc of
one day, from 0 to 24 and not over several days:
E.g. ignition time 07:00
switch-o time 18:00 OK
switch-on time 22:00
switch-o time 05:00 ERROR
before using the chrono function, set the current day and
time, therefore check that the points listed in the“Set clock” sub-
chapter have been followed.
to make the chrono function work, it must be activated as
well as programmed.
PROGRAMMING EXAMPLE12.2.2.
Let's suppose that the weekly programmer function is to be used
and 3 time periods are to be used in the following way:
1st time span: from 08:00 to 12:00 every day of the week, with
room temperature at 19°C, excluding Saturday and Sunday
2nd time span: from 15:00 to 22:00 only Saturday and Sunday
with room temperature at 21°C
3rd time span: not used
4th time span: not used
Let's set the weekly programmer as per example.
ACTIVATION OF THE CHRONO
Press theP5 key for three seconds, SET CLOCK will
appear
Press theP3 key once, SET CHRONO scrolling text will
appear
Press theP5 key once, ENABLE CHRONO and OFF
scrolling text will appear
Press theP3 key once, ENABLE CHRONO and ON
scrolling text will appear
Nota bene: When the weekly programmer is active, the LED of
the relative icon will switch-on on the control board.
At this point, press the P5 to conrm and continue programming.
TheSTART PRG1 OFF scrolling text will appear.
Let's set the time spans as per example:
SETTING FIRST TIME SPAN SWITCH-ON TIME
Use theP2 or P3 buttons to set the time “08:00”, which
corresponds to the switch-on time of the 1st time span. The
START PRG1 scrolling text will appear followed by the time
set
To conrmand continueprogramming,presstheP5 button.
Press the P4 button to go back to the previous parameter.
SETTING FIRST TIME SPAN SWITCH-OFF TIME
Use the P2 or P3 buttons to set the time “12:00”, which
corresponds to the switch-o time of the 1st time span. The
STOP PRG1 text will appear followed by the time set
Toconrmandcontinueprogramming,press theP5 button.
Press the P4 button to go back to the previous parameter.
ACTIVATION OF THE TIME SPAN FOR SELECTED DAYS AS PER
EXAMPLE
Activate the rst time span for every day of the week except
Saturday and Sunday. To do this use the P2 , P3 and P5 keys
in the following way:
P5
key - scrolls the various days, the scrolling text will appear
with the day of the week, followed by OFF
P2
and P3 key- enables/disables (ON/OFF) the 1st time
period for that day
to change day, press theP5 key
The table below indicates the activations and deactivations
of the week for the rst time span
Day Initial
value
Key function
P2
o
P3
Final
value
Key
function
P5
MONDAY OFF OFF to ON
and vice versa
ON (active
time span)
Go to next
day
TUESDAY OFF OFF to ON
and vice versa
ON (active
time span)
Go to next
day
WEDNESDAY OFF OFF to ON
and vice versa
ON (active
time span)
Go to next
day
THURSDAY OFF OFF to ON
and vice versa
ON (active
time span)
Go to next
day
FRIDAY OFF OFF to ON
and vice versa
ON (active
time span)
Go to next
day
SATURDAY OFF OFF to ON
and vice versa
OFF (time
span
deactivated)
Go to next
day
SUNDAY OFF OFF to ON
and vice versa
OFF (time
span
deactivated)
Go to next
day

THE REMOTE CONTROL 19
ENGLISH
SETTING THE TEMPERATURE FOR THE FIRST TIME SPAN
press theP5 key, SET PROG1 will appear followed by a
temperature
regulate the temperature using theP2 or P3 keys, SET
PRG1 will appear followed by the temperature set
press theP5 key to pass to the second time span
At this point, the second time span must be programmed
SETTING SECONDTIME SPAN SWITCH-ON TIME
Use theP2 or P3 buttons to set the time “15:00”, which
corresponds to the switch-on time of the 2nd time span. The
START PRG2 scrolling text will appear followed by the time
set
To conrmand continueprogramming,presstheP5 button.
Press the P4 button to go back to the previous parameter.
SETTING SECONDTIME SPAN SWITCH-OFF TIME
Use the P2 or P3 buttons to set the time “22:00”, which
corresponds to the switch-o time of the 2nd time span. The
STOP PRG2 text will appear followed by the time set
Toconrmandcontinueprogramming,press theP5 button.
Press the P4 button to go back to the previous parameter.
ACTIVATION OF THE TIME SPAN FOR SELECTED DAYS AS PER
EXAMPLE
Activate the second time span for Saturday and Sunday. To do
this use the P2 , P3 and P5 keys in the following way:
P5
key - scrolls the various days, the scrolling text will appear
with the day of the week, followed by OFF
P2
and P3 key- enables/disables (ON/OFF) the 2nd time
period for that day
to change day, press theP5 key
SETTING THE TEMPERATURE FOR THE SECOND TIME SPAN
press theP5 key, SET PROG2 will appear followed by a
temperature
regulate the temperature using theP2 or P3 keys, SET
PRG2 will appear followed by the temperature set
press theP5 key to pass to the second time span
Exit programming completely by pressing the P1 key several
times.
DEACTIVATION OF THE CHRONO
Press theP5 key for three seconds, SET CLOCK will
appear
Press theP3 key once, SET CHRONO scrolling text will
appear
Press theP5 key once, ENABLE CHRONO and ON
scrolling text will appear
Press theP3 key once, ENABLE CHRONO and OFF
scrolling text will appear
The manual controls, from the display or remote control, always
remain priority with respect to programming.
CHRONO MENU TABLE12.2.3.
The following table gives all weekly programmer function
parameters.
MENU
D1
VALUE
ADJUSTMENT
CONFIRMATION
KEY
SET
CHRONO
ENABLE CHRONO OFF
P2
P3
P5
START  PRG1 OFF  00:00
STOP  PRG1 OFF  00:00
MONDAY PRG1
OFF ...SUNDAY
PRG1 OFF ON/OFF
SET PRG1 07  35
START  PRG2
00:10 OFF  00:00
STOP  PRG2 00:10 OFF  00:00
MONDAY PRG2
OFF ...SUNDAY
PRG2 OFF ON/OFF
SET PRG2 07  35
START  PRG3
00:10 OFF  00:00
STOP  PRG3 00:10 OFF  00:00
MONDAY PRG3
OFF ...SUNDAY
PRG3 OFF ON/OFF
SET PRG3 07  35
START  PRG4
00:10 OFF  00:00
STOP  PRG4 00:10 OFF  00:00
MONDAY PRG4
OFF ...SUNDAY
PRG4 OFF ON/OFF
SET PRG4 07  35

THE REMOTE CONTROL
20
LANGUAGE12.3.
It is possible to select the preferred language to display the various
messages.
Controls procedure
Press the P5 key for 3 seconds. The SET CLOCK
SCROLLING TEXT WILL APPEAR. Press the P3 key
until LANGUAGE IS DISPLAYED. Press the P5 key once
and select the language with the P2 and P3 keys. Conrm
the selection using the P1 key. Press the same key several
times to exit the menu completely.
USER12.4.
The USER menu allows the nal customer dierent stove
settings.
DISPLAY12.4.1.
This menu allows to regulate the brightness of the display.
Controls procedure
Press the P5 key for 3 seconds. The SET CLOCK
SCROLLINGTEXT WILL APPEAR.Pressthe P3 keyuntil
USER IS DISPLAYED. Press the P5 key until DISPLAYis
shown and select the brightness of the display using the P2
and P3 keys. Conrm the selection using the P1 key. Press
the same key several times to exit the menu completely.
PELLETS12.4.2.
The following menu allows the adjustment of pellet feed as a
percentage.
If the stove has functioning problems owing to the quantity of
pellets, adjust pellet feeding directly from the control board.
The problems correlated to the amount of fuel can be divided into
2 categories:
NO FUEL
the stove can never develop a suitable ame, tending to
remain very low even at high powers.
at minimum power the stove tends to almost switch-o
taking the stove into “NO PELLETS”alarm condition.
when the stove displays the “NO PELLETS” alarm, there
may be non-burned pellets inside the burn pot.
EXCESS FUEL:
the stove develops a very high ame even at low power.
the panoramic glass is very dirty, obscuring it almost totally.
the burn pot tends to become encrusted, blocking the holes
for air intake due to the excessive pellet feed, as it is only burned
partially.
If the problem occurs after only a few months
working, check that routine cleaning stated in the
stove booklet, has been carried out correctly.
The regulation to be performed is a percentage. Therefore a
modication of this parameter will lead to a proportional variation
of all stove feeding speeds.
Controls procedure
Pressthe P5 keyfor3seconds.TheSETCLOCKSCROLLING
TEXT WILL APPEAR. Press the P3 key until USER IS
DISPLAYED. Press the P5 key until PELLET is displayed
and select the value using the P2 and P3 keys. Conrm the
selection using the P1 key. Press the same key several times
to exit the menu completely.
Adjustment example
NO FUEL: Increase the percentage value by 5 points and try
the stove with the new calibration for at least half an hour.
If the problem is attenuated, but not solved, increase by
another 5 points. Repeat the operation until the problem is
solved. If the problem cannot be resolved, contact the after-
sales service.
EXCESS FUEL: Decrease the percentage value by 5 points
and try the stove with the new calibration for at least half an
hour. If the problem is attenuated, but not solved, decrease
by another 5 points. Repeat the operation until the problem
is solved. If the problem cannot be resolved, contact the
after-sales service.
STAND  BY12.4.3.
The Stby function is used if immediate stove switch-o is required
when temperature has been reached.
The STBY function can be set at ON or OFF using the procedure
that will be described.
In the factory the STBY function is always set at OFF (indicator
o)
STAND  BY WITH DIGITALTHERMOSTAT AS12.4.3.1.
PER STANDARD
STBY FUNCTION SET AT ON
If the Stby function is activated (ON), if the stove reaches the
room temperature set, exceeding it by 2°C, it will switch-o after a
delay set in the factory, displaying STAND  BY.
When the room temperature is lower by 2°C than the set set,
the stove will start to work again at the power set on the display,
showing WORK.