Extraflame SHARON PLUS User manual

MADE IN ITALY
design & production
sharon plus
UK pellet stoves user Manual
004280809 - Rev.000

ENGLISH
APPLY TECHNICAL
DATA LABEL
2

3ENGLISH
ENGLISH............................................................................................................................................................................................................ 5
WarNINGS.............................................................................................................................................................................................5
SafEty...................................................................................................................................................................................................5
routINE MaINtENaNcE.....................................................................................................................................................................7
INStaLLatIoN.......................................................................................................................................................................................8
PREPARATIONS FOR MAINTENANCE ................................................................................................................................................................................... 8
HErMEtIcaLLy SEaLEd INStaLLatIoN ......................................................................................................................................... 10
COMbuSTION AIR......................................................................................................................................................................................................................10
FuMES EXHAuST SYSTEM......................................................................................................................................................................................................10
dEtaILS of SHaroN PLuS............................................................................................................................................................... 11
StoVE PoSItIoNING......................................................................................................................................................................... 12
MaNdatory WaLL MouNt ............................................................................................................................................................. 12
coMBuStIoN aIr.............................................................................................................................................................................. 13
fLuE GaS outLEt.............................................................................................................................................................................. 13
Hot aIr ductING.............................................................................................................................................................................. 13
AddITIONAl THERMOSTAT TO CONTROl THE duCT MOTOR................................................................................................................................13
oPEratIoN IN aIr ductING WItH tHErMoStat or ProBE (oPtIoNaL)................................................................................ 14
FuSE ................................................................................................................................................................................................................................................15
NotES for corrEct oPEratIoN .................................................................................................................................................. 15
PELLEtS aNd LoadING .................................................................................................................................................................... 16
PELLEt HoPPEr - PrESSurISEd cLoSurE..................................................................................................................................... 16
radIo/EMErGENcy card ............................................................................................................................................................... 17
radIo coNtroL................................................................................................................................................................................ 18
CONFIGuRATION .......................................................................................................................................................................................................................18
RAdIO CONTROl dEvICE ROOM PRObE CAlIbRATION.............................................................................................................................................18
bATTERY TYPE ANd REPlACEMENT...................................................................................................................................................................................18
radIo coNtroL dEVIcE fEaturES............................................................................................................................................... 19
dISPLay .............................................................................................................................................................................................. 20
GENEraL MENu ................................................................................................................................................................................. 21
GENERAl WARNINGS ...............................................................................................................................................................................................................21
fIrSt IGNItIoN SEttINGS................................................................................................................................................................ 22
dATE-TIME ...................................................................................................................................................................................................................................22
lANGuAGE ...................................................................................................................................................................................................................................22
dEGREES........................................................................................................................................................................................................................................22
oPEratIoN aNd LoGIc.................................................................................................................................................................... 23
ModES ................................................................................................................................................................................................ 24
froNt aIr .......................................................................................................................................................................................... 24
aIr ductING...................................................................................................................................................................................... 24
aIr ZoNE coNtroL........................................................................................................................................................................... 24
EaSy SEt-uP....................................................................................................................................................................................... 24
cHroNo.............................................................................................................................................................................................. 25
ENAblING .....................................................................................................................................................................................................................................25
PRG 1-4...........................................................................................................................................................................................................................................25
SEttINGS............................................................................................................................................................................................ 27
dISPlAY .........................................................................................................................................................................................................................................27
STANd bY ......................................................................................................................................................................................................................................27
OPERATION WITH AddITIONAl THERMOSTAT (OPTIONAl) ...................................................................................................................................27
dElTA-T..........................................................................................................................................................................................................................................28
FIRST lOAd...................................................................................................................................................................................................................................28
RESET ..............................................................................................................................................................................................................................................28
EASY CONTROl...........................................................................................................................................................................................................................28
OPERATION ANd SOluTIONS...............................................................................................................................................................................................29
addItIoNaL fuNctIoNS................................................................................................................................................................. 30
AddITIONAl THERMOSTAT INSTAllATION (OPTIONAl)..........................................................................................................................................30
dElAY SWITCH-OFF..................................................................................................................................................................................................................30
cLEaNING aNd MaINtENaNcE....................................................................................................................................................... 31
MaINtENaNcE................................................................................................................................................................................... 31
PERIOdIC ClEANING uNdER uSER'S RESPONSIbIlITY..............................................................................................................................................31
routINE MaINtENaNcE PErforMEd By QuaLIfIEd tEcHNIcIaNS ........................................................................................ 33
SHuT-dOWN (ENd OF SEASON)..........................................................................................................................................................................................33
dISPLayS ............................................................................................................................................................................................ 35
aLarMS .............................................................................................................................................................................................. 35
dISPoSaL............................................................................................................................................................................................ 36
attENtIoN
SurfacES caN BEcoME VEry Hot!
aLWayS uSE ProtEctIVE GLoVES!
During combustion, thermal energy is released that signicantly increases the heat of surfaces, doors, handles, controls, glass, exhaust
pipes, and even the front of the appliance. Avoid contact with those elements if not wearing protective clothing (protective gloves
included). Make sure children are aware of the danger and keep them away from the stove during operation.

it - AttENZiONE tASSAtiVO PrimA di mOVimENtArE lA StufA tOgliErE il riVEStimENtO iNdicAtO
PEr EVitArE dANNi.
EN - WArNiNg BEfOrE hANdliNg thE StOVE, thE cOVEriNg iNdicAtEd muSt BE rEmOVEd
tO AVOid dAmAgE.
fr - AttENtiON imPÉrAtifAVANt dE dÉPlAcEr lE POêlE, rEtirEr lE rEVêtEmENt iNdiquÉ
POur ÉVitEr tOut dOmmAgE.
dE - AchtuNg Pflicht BEVOr dEr OfEN BEWEgt Wird, muSS diE ANgEZEigtE VErklEiduNg ENtfErNt
WErdEN, um SchädEN Zu VErmEidEN.
ES - AtENciÓN tAXAtiVO ANtES dE mANEjAr lA EStufA quitE El rEVEStimiENtO iNdicAdO
PArA EVitAr dAñOS.
Pt - AtENÇÃO OBrigAtÓriO ANtES dE mOVimENtAr O AquEcEdOr, rEtirAr O rEVEStimENtO iNdi-
cAdO PArA EVitAr dANOS.
ENGLISH

5ENGLISH
Warnings
This instructions manual is an integral part of the product: make sure that
it always accompanies the appliance, even if transferred to another owner
or user, or if transferred to another place. If it is damaged or lost, request
another copy from the area technician. This product is intended for the use
for which it has been expressly designed. The manufacturer is exempt from
any liability, contractual and extracontractual, for injury/damage caused to
persons/animals and objects, due to installation, adjustment and mainte-
nance errors and improper use.
Installation must be performed by qualied sta, which assumes com-
plete responsibility for the denitive installation and consequent good
functioning of the product installed. One must also bear in mind all laws
and national, regional, provincial and town council Standards present
in the country in which the appliance has been installed, as well as the
instructions contained in this manual.
The use of the appliance must comply with all local, regional, national
and European regulations.
The Manufacturer cannot be held responsible for the failure to comply
with such precautions.
After removing the packaging, ensure that the content is intact and com-
plete. Otherwise, contact the dealer where the appliance was purchased.
All electric components that make up the product must be replaced with
original spare parts exclusively by an authorised after-sales centre, thus
guaranteeing correct functioning.
safety
THE APPLIANCE MAY BE USED BY CHILDREN 8 YEARS OF AGE OR
OLDER AND INDIVIDUALS WITH REDUCED PHYSICAL, SENSORY, OR
MENTAL CAPACITIES OR WITHOUT EXPERIENCE OR THE NECESSARY
KNOWLEDGE, PROVIDED THAT THEY ARE SUPERVISED OR HAVE
We thank you for having chosen our company; our product is a great heating solution developed from the
most advanced technology with top quality machining and modern design, aimed at making you enjoy the
fantastic sensation that the heat of a ame gives, in complete safety.

6ENGLISH
RECEIVED INSTRUCTIONS ON SAFE USE OF THE APPLIANCE AND THAT
THEY UNDERSTAND THE INHERENT DANGERS.
THE GENERATOR MUST NOT BE USED BY PERSONS INCLUDING
CHILDREN WITH REDUCED PHYSICAL, SENSORY AND MENTAL
CAPACITIES OR WHO ARE UNSKILLED PERSONS, UNLESS THEY ARE
SUPERVISED AND TRAINED REGARDING USE OF THE APPLIANCE BY A
PERSON RESPONSIBLE FOR THEIR SAFETY.
THE CLEANING AND MAINTENANCE REQUIRED BY THE USER MUST
NOT BE PERFORMED BY CHILDREN WITHOUT SUPERVISION.
CHILDREN MUST BE CHECKED TO ENSURE THAT THEY DO NOT PLAY
WITH THE APPLIANCE.
DO NOT TOUCH THE GENERATOR WHEN YOU ARE BAREFOOT OR
WHEN PARTS OF THE BODY ARE WET OR DAMP.
IT IS FORBIDDEN TO MODIFY THE APPLIANCE IN ANY WAY.
DO NOT PULL, REMOVE, TWIST THE ELECTRICAL CABLES COMING
OUT OFTHE PRODUCT EVEN IF IT IS DISCONNECTED FROM THE MAINS.
IT IS ADVISED TO POSITION THE POWER SUPPLY CABLE SO THAT IT
DOES NOT COME INTO CONTACT WITH HOT PARTS OF THE APPLIANCE.
THE POWER SUPPLY PLUG MUST BE ACCESSIBLE AFTER
INSTALLATION.
DO NOT CLOSE OR REDUCE THE DIMENSIONS OF THE AIRING VENTS
IN THE PLACE OF INSTALLATION. THE AIRING VENTS ARE ESSENTIAL
FOR CORRECT COMBUSTION.
DO NOT LEAVE THE PACKAGING ELEMENTS WITHIN REACH OF
CHILDREN OR UNASSISTED DISABLED PERSONS.
THE HEARTH DOOR MUST ALWAYS BE CLOSED DURING NORMAL
FUNCTIONING OF THE PRODUCT.
WHEN THE APPLIANCE IS FUNCTIONING AND HOT TO THE TOUCH,
ESPECIALLY ALL EXTERNAL SURFACES, ATTENTION MUST BE PAID
CHECK FOR THE PRESENCE OF ANY OBSTRUCTIONS BEFORE
SWITCHING THE APPLIANCE ON FOLLOWING A PROLONGED PERIOD
OF INACTIVITY.
THE GENERATOR HAS BEEN DESIGNED TO ADJUST ITSELF
AUTOMATICALLY IN PARTICULAR OPERATING CONDITIONS
THE GENERATOR HAS BEEN DESIGNED TO FUNCTION IN ANY
CLIMATIC CONDITION. IN PARTICULARLY ADVERSE CONDITIONS

7ENGLISH
STRONG WIND, FREEZING SAFETY SYSTEMS MAY INTERVENE
THAT SWITCH THE GENERATOR OFF. IF THIS OCCURS, CONTACT THE
TECHNICAL AFTERSALES SERVICE AND ALWAYS DISABLE THE SAFETY
SYSTEMS.
IN THE EVENT THE FLUE CATCHES FIRE, USE SUITABLE SYSTEMS
FOR SUFFOCATING THE FLAMES OR REQUEST HELP FROM THE FIRE
BRIGADE.
THIS APPLIANCE MUST NOT BE USED TO BURN WASTE
DO NOT USE ANY FLAMMABLE LIQUIDS FOR IGNITION
DURING THE FILLING PHASE DO NOT PUT THE BAG OF PELLETS TO
INTO CONTACT WITH THE PRODUCT
THE MAJOLICAS ARE TOP QUALITY ARTISAN PRODUCTS AND
AS SUCH CAN HAVE MICRODOTS, CRACKLES AND CHROMATIC
IMPERFECTIONS. THESE FEATURES HIGHLIGHT THEIR VALUABLE
NATURE. DUE TO THEIR DIFFERENT DILATION COEFFICIENT, THEY
PRODUCE CRACKLING, WHICH DEMONSTRATE THEIR EFFECTIVE
AUTHENTICITY. TO CLEAN THE MAJOLICAS, IT IS RECOMMENDED TO
USE A SOFT, DRY CLOTH. IF A DETERGENT OR LIQUID IS USED, THE
LATTER COULD PENETRATE INSIDE THE CRACKLES, HIGHLIGHTING
THEM.
SINCE THE PRODUCT CAN TURN ON AUTOMATICALLY THANKS TO
THE TIMER, OR REMOTELY USING THE DEDICATED APPLICATIONS, IT IS
STRICTLY FORBIDDEN TO LEAVE ANY COMBUSTIBLE OBJECT WITHIN
THE SAFETY DISTANCES INDICATED ON THE TECHNICAL DATA PLATE.
INTERNAL COMBUSTION CHAMBER PARTS CAN BE SUBJECT TO
EXTETICAL WARN, IT DOESN'T AFFECT THE FUNCTIONALITY
routine Maintenance
Based on Decree 22 January 2008 n°37 art.2, routine maintenance means
interventions aimed at reducing degradation due to normal use, as well
as dealing with accidental events entailing the need of rst interventions,
which however do not modify the structure of the system upon which one
is intervening or its intended use according to the requirements laid down
by the technical standards in force and by the manufacturer's use and main-
tenance manual.

8ENGLISH
INSTALLING INSERTS
When installing inserts, access must be prevented to the internal parts of the appliance and it must not be possible to access live parts during
extraction operations.
Any wiring, for example the power cable or room probe, must be positioned so as not to be damaged during movement of the insert and must
not come into contact with hot parts. If a cavity made of combustible material is installed, we recommend taking all the safety precautions
indicated by the installation standards.
VENTILATION AND AERATION OF INSTALLATION ROOMS
In case of non-airtight heater and/or installation, the ventilation must respect the minimum area indicated below (considering the highest value
among those provided):
Appliance categories Reference standard
Percentage of the
net opening section with respect to the
appliance fumes outlet section
Minimum net opening value of the
ventilation duct
Pellet stoves UNI EN 14785 - 80 cm²
Boilers UNI EN 303-5 50% 100 cm²
INSTALLATION
GENERAL
The ue gas exhaust and hydraulic connections must be carried out by qualied personnel who must issue installation conformity
documentation compliant with national standards.
The installer must provide the owner or person acting for him, according to the legislation in force, with the declaration of conformity,
supplied with:
1) the use and maintenance manual of the appliance and of the system components (such as for example, the smoke ducts, chimney, etc.);
2) photocopy or photograph of the chimney plaque;
3) system booklet (where applicable).
The installer must ask to be issued with a receipt stating that the documentation has been provided, and must keep it with a copy of the technical
documentation relating to the installation.
For installation in a condominium, prior approval from the condominium's administrator must be requested.
Where required, check the exhaust gas emissions after installation. Should a sampling point be installed, it must be airtight.
COMPATIBILITY
Do not install in rooms with a re hazard. It is also forbidden to install it in living areas with the following characteristics:
1. where there are liquid fuel appliances with continuous or discontinuous operation that draw the combustion air into the room in which they
are installed.
2. wheretherearetypeB gasappliances intended forheating,withor withoutdomestic hotwater productionand inadjacentand communicating
rooms.
3. where the depression measured in situ between the external and internal environment is greater than 4 Pa.
N.B.: Watertight appliances can also be installed in the cases indicated in points 1, 2 and 3 of this paragraph.
INSTALLATIONS IN BATHROOMS, BEDROOMS AND STUDIO FLATS
Installation in bathrooms, bedrooms and studio ats is only allowed for sealed or closed hearth appliances with ducted combustion air taken
from the outside.
oor protection
POSITIONING AND SAFETY DISTANCES
The support surfaces and/or points must have a suitable capacity to bear the overall weight
of the appliance, accessories and coverings. If the oor is made of a combustible material,
we recommend using a non-combustible material to protect the front part from any burnt
material which might fall during routine cleaning operations. The generator must be level
to function properly. The side walls, the rear walls and the oor support surface should be
made of non-combustible material.
One must also bear in mind all laws and national,
regional, provincial and town council regulations in force
in the country in which the appliance has been installed,
as well as the instructions contained in this manual.
Air inlet
Under any condition, including in the presence of extractor hoods and/or of controlled forced ventilation systems, the pressure dierence
between the generator installation rooms and the outside must always be equal to or less than 4 Pa.
MINIMUM DISTANCES PELLET STOVES
Installation next to ammable or heat-sensitive materials is permitted only if the special
safety distances specied on the label at the beginning of the manual (pag.2) are
observed. If the materials are not ammable, you must keep a side and rear distance of at
least 100 mm (without the inserts). For products equipped with rear spacers, wall-mounting
installation is permitted exclusively for the rear side.
PREPARATIONS FOR MAINTENANCE
To carry out extraordinary maintenance operations on the product, it may be necessary to move it away from the adjacent walls. This must be
done by a technician authorised to disconnect the combustion product evacuation ducts and then reconnect them. For heaters connected to the
hydraulic system, the connection between the system itself and the product must be made in such a way that, when an authorised technician is
about to carry out extraordinary maintenance operations, it is possible to move the heater at least 1 metre away from the adjacent walls.

3 - 5%
Max 3 mt
9ENGLISH
EXAMPLES OF CORRECT CONNECTION TO THE CHIMNEY
In the presence of type B gas appliances with intermittent operation not intended for heating, they must have their own aeration and/or
ventilation opening.
The air inlets must meet the following requirements:
they must be protected with grids, metal mesh, etc., but without reducing the net useful section;
they must be made so as to make the maintenance operations possible;
positioned so that they cannot be obstructed;
The clean and non-contaminated air ow can also be obtained from a room adjacent to that of installation (indirect aeration and
ventilation), as long as the ow takes place freely through permanent openings communicating with the outside.
The adjacent room cannot be used as a garage, or to store combustible material or for any other activity with a re hazard, bathroom,
bedroom or common room of the building.
FLUE GAS EXHAUST
The heat generator works in depression and is equipped with an outlet fan for ue gas extraction. There must be a single exhaust system for
the generator. Using a ue that is shared with other devices is not allowed.
The components of the ue gas exhaust system must be chosen in relation to the type of appliance to be installed in compliance with:
UNI/ TS 11278 in the event of metal chimneys, with particular attention to that stated in the specication;
UNI EN 13063-1 and UNI EN 13063-2, UNI EN 1457, UNI EN 1806 in the event of non-metallic chimneys.
The length of the horizontal section must be minimal and, in any case, no longer than 3 metres, with a minimum upward slope of 3%
There must not be more than 4 direction changes including the one due to the use of the "T" element.
A“T” tting with a condensation collection cap must be provided at the base of the vertical section.
If the exhaust is not inserted in an existing ue, a vertical section with a windproof end piece is required (UNI 10683).
The vertical duct can be inside or outside the building. If the smoke duct is inserted in an existing ue, it must be certied for solid fuel.
If the smoke duct is outside the building, it must always be insulated.
The smoke ducts must have at least one airtight inlet for ue gas sampling.
All the sections of the ue gas duct must be accessible to inspection.
Inspection openings must be provided for cleaning.
If the generator has a fume temperature lower than 160°C+ ambient temperature caused by the high yield (contact technicians) it
MUST be resistant to humidity.
A ue system that does not respect the previous points or, in general, that does not comply with the regulations, may cause condensation
phenomena inside it.
CHIMNEY CAP
The chimney caps must meet the following requirements:
they must have a useful outlet section no less than double that of the chimney/ducted system on which it is installed;
they must be adapted in order to prevent the penetration of rain and snow in the chimney/ducted system;
they must be built so that, in the event of winds coming from all directions and from any angle, the expulsion of combustion products
is in any case ensured;
Protection from rain
and wind
Condensation-proof
"T" tting with
inspection plug
Insulated ue
Insulated "T"
tting with
inspection plug
Protection from rain and wind
"T" tting with
inspection
plug
CONNECTION TO THE MAINS ELECTRIC SUPPLY
The generator is supplied with an electric power cable to be plugged into a 230V 50 Hz socket, possibly with a circuit breaker switch. The
socket must be easily accessible.
The electrical system must be compliant with standards. The eciency of the earthing circuit must be checked. Unsuitable earthing of the
system can cause malfunctioning for which the manufacturer will not be held liable.
Power supply variations beyond 10% can cause faulty operation of the product.
FOR GERMANY ONLY
The product can be connected to a shared ue (multi-connection) provided that the requirements of the regional and national regulations,
amongst which DIN EN 13384-2, DIN V 18160-1, DIN 18896 and of the MFeuV-2007 (Muster-Feuerungsverordnung) are strictly complied with,
and that the local chimney sweep has checked and approved the installation conditions.
Please also remember the following indications, which the end user must comply with:
• The device can be operated only with the doors closed.
• The doors and all setting devices must remain closed when the device is not on (except for cleaning and maintenance operations).

Max 3,5mt
Max 4 mt
Max 3,5mt
Max 4 mt
Max 3,5mt
Max 4 mt
Max 3,5mt
Max 4 mt
10 ENGLISH
installation example
One must also bear in mind all laws and national, regional, provincial and town council regulations in force in the country in which the appliance has been
installed, as well as the instructions contained in this manual.
Hermetically sealed installation
The generator is a fully sealed product with respect to the environment in which it is installed. This means that it is ideal for passive houses
because it does not take air in from within the house.
combustion air
To ensure the stove remains hermetically sealed, the connection pipe for the combustion air must be directly connected to the exterior, using
special pipes and sealed connectors.
Fumes exHaust system
• If the generator has a fumes temperature of less than 160°C+ room temperature due to the high performance (refer to technical data),
the fumes exhaust system must be completely waterproof.
• If there is a possibility that fumes may condense, an external inspection hatch must be tted.
Max. 1.5 m -
max. 2 elbows
Max. 1.5 m -
max. 2 elbows

a
c
b
G
F F
H H
I
JN OM
D
E
K L
F
11ENGLISH
DEtaILs OF sHarON PLUs
ARadio/emergency board IRear ducting
BSerial input JCombustion air inlet
CAccess to combustion chamber and ash drawer K230 V power supply
DFUSE LAdditional thermostat input (TA)
EOn/O MRoom air outlet
FSpacer NPellet hopper pressurised closure
GRear ue gas outlet OUpper fumes exhaust
HWall mount bracket

a
b
b
12 ENGLISH
J
THE BOOKLET ATTACHED SHOULD BE READ FOR INFORMATION ON THE INSTALLATION.
stOVE POsItIONING
To ensure the stove works correctly, it should always be positioned so that it is perfectly level, using a spirit level.
MaNDatOry waLL MOUNt
On the back of the machine, there are spacers (A) which determine the minimum distance to maintain from any rear support.
The spacers must not be removed.
The generator must be fastened to the wall using the brackets (B) supplied.
The brackets allow for an excursion to leave a gap from the generator based on requirements.
Wall plugs must be used that are suited to the type of wall on which the appliance is xed.

13ENGLISH
aDDItIONaL tHErMOstat tO cONtrOL tHE DUct MOtOr
For models with duct motor, it is also possible to thermostat the motor itself. The connection to an external thermostat will allow for the
duct motor to be controlled regardless of stove operation.
At this point, simply set the desired temperature on the thermostat; the thermostat will command the operation of the second motor:
at the set temperature (contact closed), the air ducting motor will follow the stove settings.
The duct thermostat terminal features a standard bridge.
See the example image.
cOMbUstION aIr
The generator has an inlet for drawing combustion air directly from the room or from outside the building.
FLUE Gas OUtLEt
The ue gas outlet is mounted on the top of the generator in the factory.
The ue gas outlet can be moved to the rear by following the instructions in the chapter“REAR FLUE GAS OUTLET ASSEMBLY”
THE CONVERSION OF THE UPPER FLUE GAS OUTLET MUST BE CARRIED OUT BY QUALIFIED PERSONNEL AND/OR THE
MANUFACTURER’S TECHNICIANS
HOt aIr DUctING
The machine leaves the factory with the ducting disabled.
The qualied technician is responsible for enabling it (using code 44 on the technical menu screen) only after installing the ducting pipes.
The pipe used for ducting the hot air must have an internal diameter of 80 mm and it must also be insulated or at least be protected against
heat dispersion.
THERELEVANTHOTAIRDUCTINGPIPEMUSTBEINSTALLEDBYQUALIFIED PERSONNELAND/ORBYTHE MANUFACTURER’S
TECHNICIANS
AIR DUCTING FEATURES
rear outlet possibility to thermostat the ducting
diameter of air ducting outlet: 80 mm 3 possible settings: OFF, COMFORT, AUTO.
maximum recommended air ducting length 8 m

14 ENGLISH
WITH PROBE NTC 10K
Remove the jumper and connect the NTC probe in the room that needs to be temperature-controlled through air ducting.
3 control modes:
OPEratION IN aIr DUctING wItH tHErMOstat Or PrObE (OPtIONaL)
The stove is tted with an independent motor for ducting. The connection of an external thermostat or temperature probe (NTC 10K) in the
input, located in the rear part of the stove, makes it possible to control the air ducting motor independently of the stove.
Suce it to connect the thermostat/temperature probe and set the desired temperature.
For information on air ducting settings see chapter:" Menu - Air ducting"
WITH AMBIENT THERMOSTAT OPTIONAL
Remove the jumper and connect the ambient thermostat in the room that needs to be temperature-controlled through air ducting 1.
3 control modes:
OPERATION IN AIR DUCTING WITH AMBIENT THERMOSTAT OPTIONAL
SET congured to OFF
(the temperature setting is not visible)
The air ducting motor will remain o unless the fumes temperature exceeds the
normal operating temperatures
SET congured to AUTO
(the temperature setting is not visible)
Oncethe specic activation thresholdhas been reachedand exceeded,at temperature
to be satised (CLOSED CONTACT) the air ducting motor will follow the stove settings.
When the temperature set on the thermostat is reached (OPEN CONTACT), the air
ducting motor will switch OFF and switch on again when there is a new request.
SET congured to COMFORT
(the temperature setting is not visible)
Oncethe specic activation thresholdhas been reachedand exceeded,at temperature
to be satised (CLOSED CONTACT) the air ducting motor will follow the stove settings
but at a lower speed than in SET AUTO for increased acoustic/ambient comfort.
When the temperature set on the thermostat is reached (OPEN CONTACT), the
ducting motor will switch o and switch on again when there is a new request.
OPERATION IN AIR DUCTING WITH NTC PROBE 10K OPTIONAL
SET congured to OFF
Set the desired temperature ( from 7 to 37 °C)
The air ducting motor will remain o unless the fumes temperature exceeds the
normal operating temperatures
SET congured to AUTO
Set the desired temperature ( from 7 to 37 °C)
Oncethe specicactivationthresholdhas been reached andexceeded,attemperature
to be satised the air ducting motor will follow the stove settings.
When the temperature set in TEMPERATURE is reached, the air ducting motor will
switch OFF and switch on again when there is a new request.
SET congured to COMFORT
Set the desired temperature ( from 7 to 37 °C)
Oncethe specicactivationthresholdhas been reached andexceeded,attemperature
to be satised the air ducting motor will follow the stove settings
but at a lower speed than in SET AUTO for increased acoustic/ambient comfort.
When the temperature set in TEMPERATURE is reached, the air ducting motor will
switch o and switch on again when there is a new request.

15ENGLISH
FUsE
If the stove is not powered, have the condition of
the fuse checked by a qualied technician.
Pellet hopper lid
Fire door
NOtEs FOr cOrrEct OPEratION
The following indications must be respected for correct pellet
stove operation:
Both during stove operation and when it is not used, all hatches
(pellet hopper, door, ash drawer) must remain closed at all times.
They can be opened only for the time required to load the fuel
and for maintenance.
Failure to comply with the above during operation will cause the
display to show the following:
"cLOsE HOPPEr - stOVE DOOr"
This indication means that you have 60 seconds to close the
hatch/door and the pellet lid.
After the 60 seconds, during ignition the stove will go into "DEPR
ALARM" mode, while during normal operation the stove will go
into "COOLING WAITING TIME" mode before automatically
resuming operation once the conditions are satised (cold stove,
etc.).
DUrING OPEratION, tHE EXtErNaL DOOr MUst aLways bE cLOsED!
External door

16 ENGLISH
PELLETS AND LOADING
Pellets are made by subjecting wood shavings i.e. the rejects of pure unpainted wood from sawmills, carpentry products and products from
other activities connected to wood working and transformation, to very high pressures.
This type of fuel is fully ecological as no glues are used for its compaction. In fact, pellet compactness is guaranteed over time by a natural
substance found in wood: lignite.
In addition to being an ecological fuel, making best use of wood residue, pellets also have a series of technical advantages.
While wood has a caloric value of 4.4 kWh/kg (with 15% moisture, therefore after approximately 18 months of curing), that of pellets is 5
kWh/kg.
Pellet density is about 650 kg/m3and water content is equal to 8% of its weight. For this reason pellets do not need to be cured to obtain a
sucient heat yield.
THE USE OF POOR QUALITY PELLETS OR ANY OTHER MATERIAL WILL COMPROMISE STOVE FUNCTIONS, VOIDING
THE WARRANTY AND RELEASING THE MANUFACTURER OF LIABILITY.
PELLET HOPPER  PRESSURISED CLOSURE.
During stove operation, the pellet hopper lid must always be closed.
Keep clean
Do not place the bag Directly on the stove to loaD the tank.
always use a scoop to loaD the tank. Do not rub or place weights on the tank seal. keep the tank cover
seal supporting surface clean at all times. check the conDitions of the seal frequently. if DamageD,
contact your local authoriseD technician.
The pellets used must be class A1 certied according to standard
ISO 17225-2 (ENplus-A1, DIN Plus or NF 444 of the following
category: “High quality NF biocombustible wood pellets”).
UNI EN 303-5 with the following characteristics: water content
≤ 12%, ash content ≤ 0.5% and lower caloric value >17 MJ/kg (in
the case of boilers).
The Manufacturer recommends using pellets with a diameter of
6mm with its products.
PELLET STORAGE
To guarantee combustion without problems, the pellets must be
kept in a dry place.
Open the tank lid and load the pellets using a scoop.

L2
P1
P2
L1
L6
L4
L5
L3
17ENGLISH
Radio/emeRgency caRd
The stove is tted with an emergency radio card which allows for basic control of the stove in the event of a fault or if the remote control is
malfunctioning.
The functions that can be managed from the emergency card are:
L1: Yellow LED LED
o: radio communication not available.
LED on: radio communication available.
L4: Yellow LED LED on: 5^ power set (by the user).
L2: Red LED LED o: normal operation.
LED on: alarm present. L5: Yellow LED LED on: 1^ power set (by the user).
L3: Green LED
LED o:: stove o.
LED on: stove on.
LED ashing: stove cleaning cycle under way, alarm,
stand by/cooling waiting/or blackout stand by.
L6: Green LED LED for WI-FI control: See WI-FI chapter
P1 On/O stove.
P2 Power setting.
The power increases or decreases when pressed continuously.
-

18 ENGLISH
BATTERY TYPE AND REPLACEMENT
To insert/replace the batteries, simply remove the battery
protection cover at the back of the radio control device (gure 1).
Insert the batteries according to the symbols imprinted on the
radio control device and on the battery itself.
3 AAA batteries are required for the radio control device to
function.
CONFIGURATION
RADIO CONTROL DEVICE CODING PROCEDURE:
1. Disconnect the power supply to the stove.
2. Press the keys
OK
and
OK
at the same time until the UNIT selection screen appears.
3. Using keys
OK
and
OK
select the new UNIT'.
4. Power the stove. Within 10 seconds (the LED on the emergency module will ash) conrm the selected unit by pressing
OK
on the
radio control device.
5. The LED on the emergency module will remain on for 5 seconds to conrm the new conguration.
6. If the conguration was not successful, " " will appear on the display. In this case, repeat the procedure.
J
THE RADIO CONTROL DEVICE IS ALREADY CONFIGURED WITH "UNIT 0". IF THERE IS ANOTHER STOVE, TO AVOID
INTERFERENCES, A NEW CONFIGURATION MUST BE PERFORMED, MODIFYING ONE OF THE TWO STOVES.
SOME RADIO FREQUENCY DEVICES E.G. MOBILE PHONES, ETC. MAY CAUSE INTERFERENCE WITH
COMMUNICATION BETWEEN THE RADIO CONTROL DEVICE AND THE STOVE.
Respect the environment!
Used batteries contain metals that are harmful to the environment, and therefore must be disposed of separately in
special containers.
RADIO CONTROL
(gure 1)
RADIO CONTROL DEVICE ROOM PROBE
CALIBRATION
This mode allows calibration of the room temperature detected by
the radio control device (with ventilation active only). For correct
calibration, it is recommended to position the radio control in a
room with constant temperature and wait for at least two hours.
Below nd the calibration procedure:
Access the menu and reach“TECH MENU”.
Set the access key "F4". - "ADJ REMOTE PROBE"
Using the keys
OK
or
OK
adjust the desired room
calibration.
Save and exit with the key
OK
.

2
3
1
4
5
6
7
8
19ENGLISH
RADIO CONTROL DEVICE FEATURES
1. DISPLAY
2. SET POWER/ scroll through menus / increase - select a setting
3. SET THERMOSTAT room/ scroll through menus / decrease - deselect a setting
4. Back key
5. Key to access MENU and CONFIRM
6. ON/OFF stove or restore from sleep mode.
7. Serial cable input
8. Battery compartment
The radio control device is tted with an LCD backlit display. The display remains lit for 5 seconds. After a certain period of time, in order
to minimise battery consumption, the display turns o (sleep mode).
It turns back on after pressing the ON/OFF key (6).
CAUTION!
Do not place the radio control device in direct or indirect contact with water. The radio control device may not work properly in the
presence of humidity or if exposed to water.
FREQUENCY BANDS MAXIMUM POWER TRANSMITTED
868.3 MHz 4 mW ERP
869.85 MHz 4 mW ERP

20 ENGLISH
SCREEN IN OPERATION
SCREEN WITH EXTERNAL THERMOSTAT CONNECTED TO THE TERMINAL“TA”
DISPLAY
Display text
Temperature detected in room
Set room temperature
Power 1-5^ Time
Chrono active
STAND BY
active
Battery low
display text
Time
Indicates contact of
the additional outdoor
thermostat
Tangential fan active in COMFORT mode
Tangential fan active
SCREEN IN OPERATION
Air ducting active