Extron electronics IPCP Pro Series User manual

1
IMPORTANT:
Go to www.extron.com for the complete
user guide, installation instructions, and
specifications bef
ore connecting the
pr
oduct to the po
wer source.
IPCP Pro Series • Setup Guide
The Extron IPCPPro Series IPLink®Pro Control Processors integrate Ethernet connection into AV systems to allow users to
remotely control, monitor, and troubleshoot AV equipment, including display devices and switchers. All models include an
embedded web server. Depending on the model, an IPCPPro control processor can include multiple bidirectional serial ports,
relays, IR/serial ports, digital I/O, flex I/O, switched 12 VDC power output ports, a volume control port, or contact input ports for
use in applications that require control and monitoring of multiple devices within a large-scale AV system.
All models include an Extron eBUS port, which allows a variety of eBUS devices to be connected to a single control processor.
eBUS devices include an array of button panels as well as power and signal hubs. eBUS devices are automatically recognized by
the control processor and can be added or removed at any time.
IPCP Pro Control Processors with AV LAN provide a secure network dedicated for the connection and isolation of AV devices.
This guide provides instructions for an experienced installer to install an IPCPPro Series control processor and to create a basic
configuration.
Use Extron Toolbelt software to discover and manage the IPCPPro control processor and other Extron control products.
Configure the control processor using Extron Global Configurator®software running in Global Configurator Professional
(GCProfessional) or Global Configurator Plus (GC Plus) mode, or program the control processor using Extron Global Scripter®(GS).
The IPCP integrates seamlessly with Extron GlobalViewer®Enterprise (GVE) software and Extron Control apps for remote control
applications. These control processors support multiple TouchLink®Pro touchpanel interfaces over a standard Ethernet network.
Global Configurator and other useful software applications are available at www.extron.com.
Setup Checklist: How to Proceed With Installation
Get Ready
Familiarize yourself with the features of the control processor (see Front Panel Features — Models Without AV LAN on
page4, Front Panel Features — Models With AV LAN on page5, Rear Panel Features — Models Without AV LAN
on page6, and Rear Panel Features — Models With AV LAN on page7) and of any TouchLinkPro touchpanels that
will be part of the system.
Download and install the latest version of the following:
• Toolbelt software — for discovering the control processor and other control products on the network, for managing
core settings, and for upgrading firmware when needed.
• Global Configurator (GC) software — for configuring the control system.
• Global Scripter software — for programming the control processor (as an alternative to GC)
• GUI Designer software — for designing layouts for Extron TouchLinkPro touchpanels and third party touch interfaces
• IPLinkPro device drivers — for use with GC, to make control of AV devices possible
• IR Learner Pro software — for use with models that have IR receiver ports. Use this to create your own IR drivers using
the remote control of an AV device, if drivers are not already available from Extron
All are available from www.extron.com (see Locating Software, Firmware, and Driver Files on the Extron Website on page15).
Obtain network information for the unit from the network administrator. You also need the following details for each IPLinkPro
device:
DHCP setting (on or off) Subnet mask Username
Device (IPCP Pro, TouchLinkPro, IPLPro) LAN IPaddress Gateway IP address Passwords
AVLAN IPaddress (for models with AV LAN)
Write down the MAC address of each network interface on each IPLinkPro device to be used.
Obtain model names and setup information for devices the IPCP will control.
Using a dedicated AVLAN allows you to separate device control and
traffic from a corporate or campus communication network and to
safeguard AV systems from outside intrusion or interference.

2
IPCP Pro Series • Setup Guide (Continued)
Each control processor comes with a factory-installed Secure Sockets Layer (SSL) security certificate. If you intend to install
a different SSL certificate, contact your IT department to obtain the certificate or for instructions on how to obtain one. See
“Secure Sockets Layer (SSL) Certificates” in the IPCPProSeries User Guide for requirements and guidelines regarding SSL
certificates.
Mount and Cable All Devices
Mount the unit to a rack or furniture (see Mounting on the next page).
Cable devices to the control processor (see Cabling and Features on page 8).
Connect power cords and power on all the devices.
Set Up the Control Processor and Touchpanels for Network Communication
Connect the PC that you will use for setup, the LAN (or AV LAN) port of the control processor, and the touchpanels to the
same Ethernet network. For control processor LAN and AV LAN connections, see Control, Bidirectional — LAN and AV LAN
(Ethernet) on page9.
Start Toolbelt and use it to set the IP address, subnet, gateway IP address, DHCP status, and related settings. See the
flowchart in Network Communication Setup on the next page.
NOTE: When setting up DHCP during network configuration or if using a host name instead of an IP address, the user
must enter a qualified host name (Username.HostName.Domain). For example: somename.extron.com.
Configure or Program the Control Processor and Touchpanels
The most basic steps are outlined below in the recommended order.
NOTE: See the Toolbelt Help File, Global Configurator Help File, Global Scripter Help File, and GUI Designer Help File as
needed for step-by-step instructions and detailed information. The help file for GC includes an introduction to the software
and how to start a project and configuration.
If TouchLinkPro or third party touchpanels are part of the system, start and use GUI Designer to design, save, and build the
graphical user interface (GUI) layout for the touchpanels.
NOTE: To redeem (activate) a LinkLicense®, go to www.extron.com//llredeem and follow the online instructions.
Using GC, create a new GCProfessional or GCPlus project and configure the control processor and other IP Link Pro
devices. The configuration tells the control processor:
• How its ports function • What to monitor
• How to control other products • When to do things
• Which touchpanels to interact with • Whom to notify, how, and under what circumstances
Configure ports on the control processor.
Select device drivers and link them to each serial, IR/serial, or Ethernet port.
Select settings (serial protocol, relay behavior, digital I/O or flex I/O settings) as needed.
Add eBUS devices and set them up:
Ensure that the hardware address set on each device is distinct and matches the address used in the configuration.
Assign button functions as desired.
Set up monitors, schedules, macros, and local variables.
Add touchpanels and set them up:
• Add the GUI configuration for each touchpanel to the GC project using Global Configurator.
• Assign any appropriate functions, monitors, or schedules to the touchpanels and their buttons.
If not using GC Professional or GC Plus, use Global Scripter to program the control system as desired.
Program ports on the control processor.
• Program each serial, IR/serial, or Ethernet port.
• Program relay behavior, digital I/O, and flex I/O settings as needed.
Add eBUS devices and set them up:
• Ensure that the hardware address (eBUS ID) set on each device is distinct and matches the address programmed
for it in the IPCP.
• Program button functions as desired.
Rev. E: Updated
wording regarding
adding touchpanel
GUIs.

3
Add touchpanels and set them up:
• Upload the GUI configuration for the touchpanels.
• Program the touchpanel buttons.
Save and build the project.
Upload the system configuration to the control processor.
Test and Troubleshoot
Test the system (see the IPCPProUser Guide for an outline of the system testing procedure).
Make adjustments to wiring or configuration as needed.
Network Communication Setup
Network setup is essential prior to configuration. Use the following flowchart as a guide to setting up the control processor for
network use.
Open the Toolbelt software from within
Global Congurator (GC Professional or
GC Plus mode) or as the stand-alone
application.
Start Device Discovery.
Toolbelt displays a list of all Extron control
devices connected to the network.
Using the MAC address, locate the desired
control processor in the list and select it.
Network Communication Setup
Connect the PC and the LAN port or AV LAN
port of the control processor to
the same network.
Apply power to all devices.
For each network interface
(LAN, or LAN and AV LAN), use the Set IP
feature in Toolbelt or use the
Toolbelt Manage > Network Settings tab
feature to enter the IP address and
subnet address, then congure other
network settings as needed.
Figure 1. Network Setup
Mounting
Securely mount the control processor and other devices and attach cables using the wiring section (see Cabling and Features
on page8) as a wiring guide. Optional 1U rack shelves and furniture mounting bracket kits are available for use with the control
processor. Read the instructions and UL guidelines that come with the rack shelf or mounting kit for installation procedures. See the
product-specific page at www.extron.com for a list of compatible accessories for mounting your control processor.

4
IPCP Pro Series • Setup Guide (Continued)
Panels and Locations of Features
Location and quantity of LEDs and corresponding connectors vary by model, but the functions and port wiring are identical
across models for each port type.
Front Panel Features — Models Without AV LAN
R
IPCP PRO 350
1000
LINK
ACT
IR
LAN
123
21
LIMIT
RIR
Tx
Rx
Tx
Rx
RTS
CTS
COM
IR/SERIAL RELAYS FLEX
I/O
S LIMIT
eBUS
SWITCHED
12 VDC 1000
LINK
ACT
IPCP PRO 550
OVER
43 12345678
OVER
5678
21
3 4
2134
5678
2134
COM
I/O RELAYS
IR/S
3
1
4
2
3
1
4
21
2231
S LIMIT
eBUS
OVER
Rx
CTS
RTS
Tx
S LIMIT
eBUS
OVER
RTS
1
CTS
Tx
2
Rx
COM
3
1
4
2
I/O RELAYS
1
2
IR/S
R
1000
LINK
ACT
IR
IPCP PRO 250
S
LIMIT
eBUS
OVER
Rx
CTS
RTS
Tx
COM
I/O RELAYS
IR/S
3
1
4
2
3
1
4
21
2231
NOTE: Numbers adjacent to LEDs correspond to
the like-numbered rear panel ports.
Switched
12 VDC
LEDs
COM (Serial)
LEDs
COM
(Serial)
LEDs
IR/Serial
LEDs
IR/
Serial
LEDs
Flex I/O
LEDs
Reset
Button
(recessed)
Reset Button
(recessed)
eBUS LEDs
eBUS
LEDs
IR Receiver
Relay
LEDs
Relay
LEDs
eBUS LEDs
IR Receiver
IR Learning
Angle and
Distance
LAN/
Network
LEDs
Digital I/O LEDs
IR Receiver
LAN/
Network
LEDs
Digital
I/O
LEDs
Power
LED
Power
LED
Power
LED
1 2 3
4 5 6
7 8
0
9
2–12"
(4–30 cm)
15˚ 15˚
IPCP Pro Embedded Control Processor Without AV LAN
(within another device)
NOTES:
• For reset mode information, see the IPCPProSeries User Guide.
• The Reset button and power LED for the IPCPPro embedded control processors are located next to the rear panel
connectors.
• The embedded control processors do not have an IR learning sensor.
Figure 2. Front Panels: IPCP Pro Series Rack Mountable Models
Without AV LAN

5
Front Panel Features — Models With AV LAN
This section shows the front panels of a couple representative AV LAN models, not all models.
R
IPCP PRO 360
1000
LINK
ACT
IR
AV LAN
123
LAN
COM
I/O RELAYS
IR/S
3
1
4
2
3
1
4
21
2231
LIMIT
eBUS
OVER
Rx
CTS
RTS
Tx
ERROR
LINK
BUSY
COM (Serial)
LEDs
IR/Serial
LEDs
Reset
Button
(recessed)
eBUS LEDs
IR
Receiver
Relay
LEDs
LAN
LEDs
AV LAN
LEDs
Digital I/O
LEDs
Power
LED
Figure 3. IPCPPro360 Front Panel
LIMIT
eBUS
OVER
Rx
CTS
RTS
Tx
ERROR
LINK
BUSY
COM
I/O RELAYS
IR/S
12 121
COM
(Serial)
LEDs
IR/
Serial
LEDs
eBUS
LEDs
Relay
LEDs
Digital
I/O
LEDs
IPCP Pro Embedded Control Processor With AV LAN
(within another device)
Figure 4. Figure 3: IPCP Pro Embedded Control Processors With AV LAN — Front Panel
Rev. E: Added
IPCP Pro 355M
front panel.

6
IPCP Pro Series • Setup Guide (Continued)
Rear Panel Features — Models Without AV LAN
LAN
123
GTx Rx GTx Rx
COM 2 COM 3
RELAYS
2143CC
LAN
eBUS
FLEX I/ORELAYSIR/SERIALCOM12 VDC
Tx Rx GTxRxG Tx Rx GTxRxG SGSG SGSG
SGSG SGSG
RTSCTS
IPCP PRO 550
Tx Rx GTxRxG Tx Rx GTxRxG RTSCTS
1.2A MAX
SWITCHED 12 VDC
40W MAX TOTAL
COM 1
GTx Rx RTS CTS
IR/SERIAL
1
SG
2
SG
POWER
R
12V
1.0A MAX
1234G
DIGITAL I/O
eBUS
+V +S -S G
PWR OUT = 6W
23
GTx Rx GTx Rx
COM 2COM 3
RELAYS
2143CC
COM 1
GTx Rx RTS CTS
IR/SERIAL
1
SG
2
SG
1234G
DIGITAL I/O
eBUS
+V +S -S G
PWR OUT = 6W
3 4
1 1 2 3 7
8
4 5 6
2 1 2
5 6
3 4
7 8
1 2
5 6
3 4
783214G
+V +S -S G
PWR OUT = 12W
100-240V ~ 50-60Hz
IPCP PRO 350
PWR OUT = 6W
VCG
VOL
POWER
12V
1.0A MAX
G
Tx Rx
RTSCTS
COM 1
3
12 4G
DIGITAL I/O
G
Tx Rx
COM 2
-S+V +S G
eBUS
C12
RELAYS
SG
IR/S
LAN
IPCP PRO 250
1
MAC: 00-05-A6-XX-XX-XX S/N: ####### E######
00-05-A6-XX-XX-XX
MAC: 00-05-A6-XX-XX-XX
S/N: ####### E######
00-05-A6-XX-XX-XX
MAC: 00-05-A6-XX-XX-XX
S/N: ####### E######
DDDDE
EEE
I
PCP Pro 550
I
PCP Pro 350
DDDDEEEE
IPCP Pro 250
AAAA
A
AAA
C
CCCBBBBDDDDEEEEHHHH
I
III
D
DDDEEEEIIIIIIII
KKKK
J
JJJ
J
JJJ
J
JJJ
F
FFF
F
FFF
GGGG
G
GGG
F
FFFGGGG
L
LLL
L
LLL
L
LLL
LLLL
M
MMM
M
MMM
M
MMM
JJJJFFFFGGGG
IPCP Pro Embedded
Cont
rol Processor
Withou
t AV LAN
(w
ithin another
de
vice)
Figure 5. IPCPPro Control Processors Without AV LAN —Rear Panels
APower input connector (external power supply) HFlex I/O ports (digital input/output or analog input)
BPower input connector (internal power supply) IDigital I/O ports (digital input/output)
cSwitched 12 VDC power output ports JeBUS ports
D3-pole COM ports (RS-232-only) KVolume control port
E5-pole COM ports (RS-232/RS-422/RS-485) LLAN connectors and LEDs (Ethernet)
FIR/serial output ports MMAC address label
GRelay ports

7
Rear Panel Features — Models With AV LAN
This section shows rear panels of some representative models with AV LAN.
12
PWR PWR
3
PoE+ OUT PoE+ OUT
GTx Rx GTx Rx
COM 2 COM 3
RELAYS
2143CC
AV LAN
LAN
COM 1
GTx Rx RTS CTS
IR/SERIAL
1
SG
2
SG
1234G
DIGITAL I/O
eBUS
+V +S -S G
PWR OUT = 6W
IPCP PRO 360
PWR OUT = 6W
VCG
VOL
POWER
12V
1.0A MAX
G
Tx Rx
RTSCTS
COM 1
3
12 4G
DIGITAL I/O
G
Tx Rx
COM 2
-S+V +S G
eBUS
C12
RELAYS
SG
IR/S
LAN
AV
LAN
50-60 Hz
100-240V ~ 1.5A MAX
R
LAN
GTx Rx GTx Rx
COM 2COM 3
RELAYS
2143CC
COM 1
GTx Rx RTS CTS
IR/SERIAL
1
SG
2
SG
1234G
DIGITAL I/O
eBUS
+V +S -S G
PWR OUT = 6W
AV LAN 2
AV LAN 1
AV LAN 3
MAC: 00-05-A6-XX-XX-XX
S/N: ####### E######
MAC: 00-05-A6-XX-XX-XX
S/N: ####### E######
MAC: 00-05-A6-XX-XX-XX
S/N: ####### E######
00-05-A6-XX-XX-XX
IPCP LAN
MAC: 00-05-A6-XX-XX-XX
S/N: ####### E######
00-05-A6-XX-XX-XX
IPCP AV LAN
DDDDE
EEE
I
PCP Pro 360
DDDDEEEE
IPCP Pro 255
AAAA
I
III
L
LLLIIII
KKKK
J
JJJ
J
JJJ
F
FFFGGGG
F
FFFGGGG
N
NNN
N
NNN
LLLL
MMMM
M
MMM
BBBB
D
DDDEEEEIIII
LLLLNNNNJJJJFFFFGGGG
IPCP Pro Embedded
Cont
rol Processor
With
AV LAN
(w
ithin another
de
vice)
Figure 6. IPCP Pro Control Processors With AV LAN — Rear Panels
APower input connector (external power supply) IDigital I/O ports (digital input/output)
BPower input connector (internal power supply) JeBUS ports
D3-pole COM ports (RS-232-only) KVolume control port
E5-pole COM ports (RS-232/RS-422/RS-485) LLAN connectors and LEDs (Ethernet)
FIR/serial output ports MMAC addresses
GRelay ports NAV LAN connector and LEDs (Ethernet), some with PoE+
and PoE+ LEDs
The following ports are not shown in figure 6 but are available in some AV LAN models such as the IPCPPro555.
cSwitched 12 VDC power output ports HFlex I/O ports (digital input/output or analog input)

8
IPCP Pro Series • Setup Guide (Continued)
Cabling and Features
Attach cables using the following wiring diagrams as a guide. Full details are available in the IPCPPro Series User Guide.
ATTENTION:
• Installation and service must be performed by experienced personnel.
• L’installation et l’entretien doivent être effectués par du personnel expérimenté.
Power Input — External
POWER
12V
x.xA MAX R
Ground all devices.
External
12 VDC
Power Supply
+12 VDC input
– Return
Ridged
Smooth
To
AC
power
Front Panel
Power Input, External Power Supply
• Front panel LED ( ) blinks during
boot-up and remains lit when the
IPCP is powered and operational.
• Connect to
included 12 VDC
power supply.
NOTE: Check the polarity of the power
supply before connecting it to the IPCP.
Ridged
Smooth
Tie Wrap
3/16"
(5 mm)
Max.
Power Input — Internal
R
1.2A MAX
100-240V 50-60Hz
Power Input, Internal Power Supply
• Front panel LED ( ) blinks
during boot-up and remains lit
when the IPCP receives power.
• Connect to 100 to
240 VAC.
Rear
Panel
Front Panel
Power Output — Switched 12 VDC Power Output
21 LIMIT
SWITCHED
12 VDC
OVER 43
12 VDC
SWITCHED 12 VDC
40W MAX TOTAL
3 4
1 2
Lights if total power drawn
is 41-46 watts.
Lights if total power drawn
exceeds 47 watts.
Power output shuts off
until the user corrects the
overload.
Switched 12 VDC
Power Output
• Total output for all four ports
combined:
12 VDC, 40 watts (max.)
• Corresponding front panel
green LEDs ( ) light when
power is available at each port.
3/16"
(5 mm)
Max.
Rear
Panel
Front
Panel
Tie Wrap
Power Output — PoE+
The IPCPPro360 can output PoE+ on AV LAN ports 2 and 3. For details, see the PoE+ output information on page 11.
ATTENTION:
• Always use a power
supply supplied or
specified by Extron. Use
of an unauthorized power
supply voids all regulatory
compliance certification and
may cause damage to the
supply and the unit.
• Utilisez toujours une source
d’alimentation fournie par
Extron. L’utilisation d’une
source d’alimentation non
autorisée annule toute
certification de conformité
réglementaire et peut
endommager la source
d’alimentation que l’unité.
Rev. E: replaced
isometric power
supply with
orthogonal version.
Updated French
translation of 2nd
paragraph.

9
Control, Bidirectional — Serial (COM)
GTx Rx GTxRxG
RTS
Tx Rx GTxRxG RTSCTS
CTS
COM 1
GTx Rx RTS CTS
I
I
R
/S
E
R
R
IAL
1
S
S
G
2
S
G
1 7
8
4
GTx Rx Tx Rx
COM 2 COM
RE
EL
REL
2
2
1
C
T
T
T
T
T
T
T
T
T
Tx
x
x
x
x
Rx
M
M
M
M
COM
LA
A
A
A
A
Y
Y
YS
L
A
A
A
A
A
A
Y
Y
Y
YS
4
3
3
3
Tx
Rx
1
Tx
Rx
Tx
Rx
RTS
CTS
COM
12345678
COM
231
Rx
CTS
RTS
Tx
NOTE: If you use cable that has a drain wire, tie the drain wire to ground at both ends.
Projector, Panel
Display, PC, or Other
RS-232, RS-422, or
RS-485 Device
RS-232-
Controllable
Device
Receive (Rx)
Transmit (Tx)
Transmit
Receive Receive (Rx)
Transmit (Tx)
Ground
Request to send
Clear to send
Transmit
Rx Receive
Tx
CTS
RTS
GGround
Rx
G
Tx
Strip wires
3/16" (5 mm) max.
CO
COM
Front Panels
5-pole COM
(RS-232, RS-422, RS-485)
3-pole COM
(RS-232)
Select protocol via software.
COM port default protocol:
• 9600 baud
• 8 data bits • 1 stop bit
• no parity • no ow control
NOTE: The 5-pole COM ports support both
hardware and software ow control.
The 3-pole COM ports support software
ow control only.
Serial (COM) Ports
Rear
Panels
Heat Shrink
To 3-pole
COM port
To 5-pole
COM port
Heat Shrink
Over Shield Wires
or or
RTS = Request to Send
CTS = Clear to Send
Tx = Transmitting Data
Rx = Receiving Data
RS-232
Tx
Rx
Ground
RTS
CTS
RS-422
Tx-
Rx-
Ground
Tx+
Rx+
RS-485
Ground
5-pole COM Pin Configurations
Data-
(pins 1 & 2
tied together)
Data+
(pins 4 & 5
tied together)
Pin
1(Tx)
2(Rx)
3(G)
4(RTS)
5(CTS)
Control, Bidirectional — LAN and AV LAN (Ethernet)
Default port IP addresses and recommended connections vary depending on whether or not the IPCP model includes AV LAN
ports.
Models without AV LAN — LAN ports
1000
LINK
ACT
LAN
123
LAN
LAN
12
RJ-45
Connector
Insert
Twisted Pair Wires
Pins: 12345678
Rear Panel,
Rack Mount
Models
Front Panel,
Rack Mount
Models
NOTE: IPCPs with more than one LAN port function as
multiport, unmanaged network switches so you can
connect additional devices to the same network.
Ethernet
Link
LED
Activity
LED
1000 Mbps
Connection
Network is
active.
Data is being
sent/r
eceived.
or
TCP/IP
Network
LAN (Ethernet) — Models Without AV LAN
Default protocol, public ports: Default login
credentials:
• Username:
admin
• Password:
extron
• IPCP IP address: 192.168.254.250
• Gateway IP address: 0.0.0.0
• Subnet mask: 255.255.255.0
• DNS address: 127.0.0.1
• DHCP client: off
• Link speed and duplex level: autodetected
• Data rates: 10/100/1000Base-T
PC
3/16"
(5 mm)
Max.
7/8"
(22 mm)
Heat Shrink
on Outer
Jacket to
Inner
Conductor
Transition
Extron
STP 20-2P Cable
TIP: STP 20-2P
cable, shown
at left, is
recommended
for these
connections.
For best
results,
insulate the
common or
drain wires
using heat
shrink.

10
IPCP Pro Series • Setup Guide (Continued)
Models with AV LAN — LAN ports
1000
LINK
ACT
AV
LAN
1
2
3
LAN
1
L
LAN
A
AV
LA
A
N
MAC: 00-05-A6-XX-XX-XX
S/N: ####### E######
MA
C
:
00
-
0
05
-A
6-
YY-YY-Y
Y
Y-
Y
Y
S/
N: ###
#
#
###
E###
E
##
#
##
#
LAN
2
1
PWR
PWR
3
P
o
o
E+ OU
T
P
oE+
O
O
UT
A
AV
L
AN
A
AV L
AN
MAC: 00-05-A6-YY-YY-YY
S/N: ####### E######
00-05-A6-XX-XX-XX
IPCP LAN
MAC: 00
00
-
05
-A
6-
XX
-
XX
X
-
X
X
S/
N:
#
#
#
#
#
#### E###
#
#
#
#
00
-
-
0
0
5-A6-XX-XX-
X
X
X
I
P
C
C
P AV LA
N
RJ-45
Connector
Insert Twisted
Pair Wires
Pins:
12345678
Rear
Panels
Front
Panels
NOTE: IPCPs with more than one LAN or AV LAN port function as multiport, unmanaged
network switches so you can connect additional devices to the same network.
Link
LED
Activity
LED
1000 Mbps
Connection
Network is
active.
Data is being
sent/r
eceived.
or
LAN (Ethernet) —
Models With AV LAN
Default protocol, LAN
ports:
• LAN IP address:
192.168.253.250
• Gateway IP address:
0.0.0.0
• Subnet mask:
255.255.255.0
• DNS address: 127.0.0.1
• DHCP client: off
• Link speed and duplex
level: autodetected
• Data rates:
10/100/1000Base-T
Default login
credentials:
• Username: admin
• Password: extron
Ethernet
Corporate
TCP/IP
Network
Ethernet
Corporate
TCP/IP
Network
PC
PC
Models with AV LAN — AVLAN ports
1000
LINK
ACT
AV LAN
123
L
A
N
1
L
LA
AN
AV
LAN
MA
C
:
00
-
0
05
-A
6-
XX-XX-X
X
X-
X
X
X
S/
N: ###
#
#
###
E###
E
##
#
##
#
MAC: 00-05-A6-YY-YY-YY
S/N: ####### E######
LAN
21
PWR PWR
3
PoE+ OUT PoE+ OUT
AV LAN
M
A
C
:
00
-
-05
-A
6-
YY
-
YY
-
YY
S/
N: ##
#
#
#### E#####
#
00-
0
0
5-A6-XX-X
X
X
-XX
I
PCP LAN
MAC: 00-05-A6-XX-XX-XX
S/N: ####### E######
00-05-A6-XX-XX-XX
IPCP AV LAN
RJ-45
Connector
Insert Twisted
Pair Wires
Pins: 12345678
NOTE: IPCPs with more than one LAN or AV LAN
port function as multiport, unmanaged network
switches so you can connect additional
devices to the same network.
Rear
Panels Front Panels
Link
LED
Activity
LED
1000 Mbps
Connection
Network is
active.
Data is being
sent/received.
or
AV LAN (Ethernet)
Default protocol,
AV LAN:
• IP address:
192.168.254.250
• Subnet mask:
255.255.255.0
• DNS address: 127.0.0.1
• DHCP client: off
(disabled)
• DHCP server off
(disabled)
• Link speed and duplex
level: autodetected
• Data rates:
10/100/1000Base-T
Default login
credentials:
• Username: admin
• Password: extron
Ethernet
Ethernet
PC
AV LAN DHCP Server
The AV LAN DHCP Server is disabled by default. It can be enabled to dynamically assign
IP addresses to DHCP clients on the AV LAN.
AV
Network
PC
AV
Network
Default protocol, AV LAN when
DHCP server is enabled:
• DHCP server IP address: 192.168.254.1
• Subnet mask: 255.255.255.0
• DNS address: 192.168.254.1
• DHCP dynamic address range for client
devices: 192.168.254.100 -
192.168.254.149
• Maximum served addresses when
DHCP server is enabled: 50
• DHCP client address lease time: 24 hours.
To use DHCP in the AV LAN:
1. Using Toolbelt, enable the DHCP server
for the AV LAN within the control
processor (see the software or
programming help le for details).
2. Enable DHCP on each client AV device
(see the user guide for each product).
3. Connect client AV devices to the AV LAN.

11
PoE+ output: The IPCPPro360 offers Power over Ethernet+ (PoE+) output on AV LAN ports 2 and 3.
These RJ-45 connectors, labeled “PoE+ Out,” can output a maximum of 30watts per port.
The corresponding PowerLED lights when the port provides power. PoE+ ports can be monitored for status
and power consumption, and power output can be scheduled.
For details, see the IPCP Pro Series User Guide and the Global Configurator Help File.
ATTENTION:
• Power over Ethernet (PoE) is intended for indoor use only. It is to be connected only to networks or circuits that are not
routed to the outside plant or building.
• L’alimentation via Ethernet (PoE) est destinée à une utilisation en intérieur uniquement. Elle doit être connectée
seulement à des réseaux ou des circuits qui ne sont pas routés au réseau ou au bâtiment extérieur.
All models (with or without AV LAN)
MAC address: Each network interface of the control processor is assigned a unique
user hardware ID number (MAC address) (for example, 00-05-A6-05-1C-A0). You may need this
address during control processor configuration. A label that indicates the MAC address is located
on the rear or side panel of the unit.
Control, Unidirectional — IR/Serial
IR/SERIAL
5678
2134
IR/S
1
2
IR/SERIAL
1
SG
2
SG
IR/SERIAL
SGSG SGSG
SGSG SGSG
1 2
5 6
3 4
7 8
Rear Panels Front Panels
To the IR Receiver of a
Projector, Display, or
Source Device
S
G
(-)
(+)
(-)
(+)
(+)
(-)
Two Single IR Emitters
Ground
IR Output Signal
Unidirectional
IR
IR or RS-232
Output
Ground
To a Projector,
Panel Display, or the
Wired IR Remote or
RS-232 Port of a
Source Device
IR/Serial LEDs
Light when signals are transmitted
on the corresponding IR/serial port.
IR/Serial Ports
Output options:
• IR (30 kHz to 300 kHz,
with or without carrier signals)
• Unidirectional RS-232
or or
or
Control, Unidirectional — Relays
RELAYS
2143CC
RELAYS
1 2
5 6
3 4
7 8
RELAYS
5678
2134
Rear Panels Front Panels
Normally
Open (2)
Common
Normally
Open (1)
Common
To Room
Control
Equipment
To Room
Control
Equipment
Closed
Normally
Open
21C 21C
Relays
• Connect devices for contact control.
• Do not exceed a total of 24V at 1A for each port.
or
Common
Relay 2
Relay 1
All relays
are
normally
open.
Relay LEDs
Light when the corresponding relays
are activated (tied to GND, closed).
PW
R
PoE+ OUT
MAC: 00-05-A6-XX-XX-XX
S/N: ####### E######
00-05-A6-XX-XX-XX
MAC: 00-05-A6-XX-XX-XX
S/N: ####### E######
MAC
Address

12
IPCP Pro Series • Setup Guide (Continued)
Control, Unidirectional — Flex I/O or Digital I/O
1234G
DIGITAL I/O
FLEX I/O
3214G
FLEX
I/O
34
21
I/O
3
1
4
2
Digital I/O (digital input/output)
Congure each port as a digital input or output,
with or without +5 VDC pull-up.
Use these ports to:
• Monitor or trigger events and functions (toggle relays,
issue commands, send e-mail), once congured.
• Power LEDs or other devices that accept a
TTL signal.
Flex I/O (digital input/output or analog input)
Congure each port as an analog input or as a digital
input or output with or without +5 VDC pull-up.
Switch,
Sensor
2
1
3
4
G
Heat
Shrink
Over
Shield
Wires
(Switches, sensors,
LEDs, relays, or
similar items)
Rear PanelFront Panel
Digital I/O
LEDs
Light when the
corresponding
ports are active.
Flex I/O LEDs
Light when the
corresponding
ports are active.
Ground
Share the same ground among
I/O connections.
Device 4
Device 3
Device 2
Device 1
Wire
Nut
Control — eBUS
eBUS
eBUS
+V +S -S G
PWR OUT = 6W
+V +S -S G
PWR OUT = 12W
MUTE
VOLUME
VIDEO
DVD
PC
DOC CAM
LAPTOP
VIDEO
PC
VOLUME
DISPLAY
OFF
ON
SLIMIT
eBUS
OVER
LIMIT
eBUS
OVER
ERROR
LINK
BUSY
Rear Panels,
Rack Mount Models
eBUS Accessory Port
Connect the rst eBUS device to this port, then connect other
eBUS devices and accessories to that device in the desired
topology (daisy chain, star, or combination).
• Wire the connectors the same at both ends for every eBUS
device.
• See the eBUS Technology Reference Guide for the
recommended distance from the control processor to the
last eBUS device and maximum quantity of devices per
control processor.
• The IPCP Pro can provide power to the button panel devices.
Front Panels,
Rack Mount Models
eBUS Link LED (green)
Lights steadily and remains lit
when the unit detects connected
eBUS devices, there are no ID
conicts, and eBUS rmware is
not currently being synchronized.
eBUS Busy LED (amber)
Blinks while eBUS rmware is
being synchronized.
eBUS Error LED (red)
Blinks if the unit detects an
eBUS ID conict.
eBUS Status LED (green)
LED is not lit — This indicates one of the following
conditions:
• No power is present.
• No eBUS devices are detected.
LED is blinking fast — An eBUS ID conict has
occurred: two devices have the same bus ID number.
LED is blinking slowly — A rmware update is in
progress: the control processor is synchronizing
rmware of the eBUS panel(s).
LED is lit steadily — Power is present with conrmed
communication and there are no eBUS ID conicts
in the entire system.
eBUS port
on an
eBUS device
(button
panel or
similar
device)
+S
+V
-S
G
+ Signal
+12 VDC
- Signal
Ground
Drain Wires
eBUS Limit LED
(amber)
Lights steadily and
remains lit while the
eBUS port uses the
maximum threshold
power.
eBUS Overload LED
(red)
Lights steadily when the
eBUS port exceeds
maximum threshold
power usage and enters
the fault state.
During this fault state,
eBUS port power is
shut down until the
power usage falls back
below the threshold.
The Over LED remains
lit during the fault state.

13
+V G -S +S+V G -S +S+V G -S +S
eBUS DISTRIBUTION HUB
PWR OUT = 6W
-S+V +S G
eBUS
IPCP Pro
Rear Panel
+
V+
S G
–
S
eBUS port on an
EBP or other
eBUS device
G - S+S
+V
Tie drain wires to ground.
X
G - S+S
G - S+S
Tie drain wires to ground.
G
- S
+S
+V
+Signal
- Signal
+12 VDC
Ground
G - S+S
+V
G - S+S
+V
Powered
eBUS
device(s)
eBUS Connections
• Connect up to four (4) eBUS devices to the
eBUS distribution hub (EBDB MINI).
• Wire the connectors the same at both ends.
ATTENTION: Do NOT
connect the power pin
to any device that is
already powered by the
IPCP Pro control
processor or by an
additional power supply.
ATTENTION:
• Do NOT connect the power pin to
any device that is already powered
by the IPCP Pro control processor
or by an addi tional power suppl y.
• NE connectez PAS la broche
d'alimentati on à un appareil déjà
alimenté par le processeur de
contrôle IPCP Pro ou par une autre
source d'alimentati on.
3/16" (5 mm) Max.
EBDB MINI
Rear Panel
(or use
an EBDB
10-port hub)
Control — Volume
VCG
VOL
VCG
10V 50mA
GCV
REMOTE
10V 50mA
GCV
10V
REMOTE
VOL/MUTE
REMOTE
VOL/MUTE
10V 50mA
G STANDBY
10V 50mA
GCV
VCG
VOL
Ground (Gnd)
C
G
V
Ground
Reference voltage
C
G
Control voltage
V
Reference voltage input (from amplier) – This allows the IPCP Pro to detect when the amp is present.
Control voltage (variable output to amp from IPCP Pro) – This signal controls the amp volume.
Control voltage output:
0 - 10 VDC
Reference
voltage: ≤10 VDC
Example:
Connecting to
Extron Amplifiers
IPCP Pro
Rear
Panel
Rear Panel
Volume Control
This port can be used to control the volume and mute or
unmute the audio for Extron half rack width audio ampliers.
• Connect to an Extron audio amplier to permit volume
control via touchpanel controls, macros, or schedules.
• Do not exceed 10 VDC input voltage.
Congure the maximum and minimum voltage limits. Set
Soft Start mode off or on (default). Soft Start mode allows
volume to gradually increase from mute to the previous level
after muting or power-on to prevent loud audio bursts.
C or VOL/MUTE
V or 10V G or
MPA 401 Series
MPA 181T,
MP 101 Series
MPA 152MPA 152 Plus
XPA 1002
NOTE: Use shielded
cable and place the
control processor as
close as possible to
the amplier to avoid
picking up background
noise via the cable.
Ideal cable length is
six feet (1.8 m) or less.
NOTE: When audio mute is active,
the control processor sets output
voltage to 0 VDC, even if the
voltage range (minimum and
maximum voltage limits) has been
set to levels above zero, such as
2 V to 8 V.

14
IPCP Pro Series • Setup Guide (Continued)
Reset Modes: a Brief Summary
The IP Link Pro control processors offer the following reset modes:
• Use Factory Firmware: Press and hold the front panel Reset button while applying power to the unit. Keep holding the
button down until the Power LED blinks twice, or for 6 seconds, then release the button. The
control processor enters factory firmware mode. For units with firmware prior to version 2.x, the
LED blinks quickly. Use this mode to revert to factory firmware in the event of a firmware failure.
Do not continue to operate the control processor using the factory rmware version. If you want
to use the factory default rmware version, you must upload that version again.
• Project Recovery: See the IPCP Pro Series User Guide for instructions. Use this mode to recover the project in the
event of a lost user name and password.
• Run/Stop Program: Hold down the Reset button for about 3 seconds, until the Power LED blinks once. Release
and press the Reset button momentarily (for <1second) within 1second. (Nothing happens if
the momentary press does not occur within 1second.) The LED blinks 2 times if the program is
starting. The LED blinks 3 times if the program is stopping. This mode allows you to restart any
programs stopped by an IP settings reset.
• Toggle DHCP Client: Press the Reset button five times (consecutively). Release the button. Do not press the button
within 3seconds following the fifth press. Use this mode to enable or disable the DHCP client
for the LAN port.
• The Reset LED blinks 6 times if the DHCP client is enabled.
• The Reset LED blinks 3 times if the DHCP client is disabled.
NOTES:
• DHCP toggle mode is supported on firmware version 3.0 or higher.
• By default DHCP is off and the unit uses a static IP address.
• When you disable the DHCP client, the unit reverts to using the previously-set static
IP address.
• Reset All IP Settings: Press and hold the front panel Reset button for 6 seconds. After the Power LED blinks twice,
release and momentarily press the Reset button. Use this mode to reset all network settings
to factory default values without affecting user-loaded files. This reset mode also stops any
running programs. This resets the settings for both LAN and AV LAN ports, including turning
DHCP off.
• Reset to Factory Defaults: Press and hold the front panel Reset button for 9 seconds. After the Power LED blinks
three times, release and momentarily press the Reset button. Use this mode to return the
control processor to factory default settings. This mode also deletes all user-loaded files and
configurations.
For detailed information on each mode and its use, see the IPCP Pro Series User Guide at www.extron.com.
Resources
Obtaining Control Drivers
Extron provides an extensive selection of device drivers available on the Extron website. If the system requires a control driver
that is not already available, you have additional options:
• Request a new serial (RS-232) or Ethernet driver from Extron.
• Create your own custom IR device driver using IRLearnerPro software. Follow the directions in the IRLearnerPro Help File
to create a driver by using the remote control for that device and the IR receiver port on the front panel of the IPCPPro.
Obtaining Instructions, Information, and Assistance
A checklist of basic setup steps is provided at the beginning of this guide. For additional information see the help files and the
IPCPProSeries User Guide, available at www.extron.com.
If you have questions during installation and setup, call the ExtronS3 Sales & Technical Support Hotline or the ExtronS3
Control Systems Support Hotline [phone]).
Rev. B: Added Run/
Stop Program mode
and new DHCP toggle
mode.
For Use Factory FW:
Per peer reviewer
(Sean), added “ Do not
continue to operate
the control processor
using the factory
firmware version.
If you want to use
the factory default
firmware version,
you must upload that
version again. “

15
Locating Software, Firmware, and Driver Files on the Extron Website
There are three main ways to find software, firmware, and device drivers within www.extron.com:
• Via links from the web page for the specific product
• Via the Download page (Click on the Download tab at the top of any page within www.extron.com.)
• Via links from search results
NOTES:
• For some software you have the option to click the Download Now button to begin downloading the software file. For other
software there is a link for contacting an Extron support representative who can provide you access to the latest version.
To obtain Extron control product software, you must have an Extron Insider account. Extron provides training to our
customers on how to use the software. Access to the full features of Global Configurator Professional is available to
those who successfully complete Extron Control Professional Certification.
• New RS-232 and Ethernet drivers are required. You must use serial and Ethernet drivers developed specifically
for the IPLinkPro platform. With the exception of IR device drivers, drivers used for the previous generation
IPLink (non-Pro) control processors are not compatible.
Rev. E: replaced GC-specific
wording about downloads with
generic “Extron control product
software” wording.

16
IPCP Pro Series • Setup Guide (Continued)
© 2014-2018 - Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
68-2438-50
Rev. E
08 18
Overall Configuration Procedure for the Control Processor
Configure the IP settings of
the control processor and the
TouchLink Pro touchpanels.
See Network
Communication Setup
Create GUI layouts for the
touchpanels or other interfaces:
1. Start GUI Designer.
2. Create GUI layout designs for each
TouchLink Pro, third party
touchpanel (with a TouchLink
Interface), or a computer or
mobile device (with LinkLicense).
3. Save and build the GUI layout le.
Or...
Download existing GUI layouts
from identical touchpanels.
Create monitors, schedules, timers,
macros, and local variables.
Add touchpanels or other interfaces
(if used) to the project.
Congure ports on the
control processor.
Import GUI layouts and congure the
touchpanels or other interfaces.
Test the system, make adjustments,
nalize conguration.
Save the project.
Build and upload the conguration to
the control processor.
If desired or required, install a new
security certicate (via Toolbelt).
Will
TouchLink Pro or
third party touchpanels or
other user interfaces
be used?
No Yes
Create a new GC Professional or GC Plus project
and add the control processor to it.
Within Global Configurator
(GC Professional or
GC Plus mode):
Figure 7. Overall Configuration Steps
Network
Communication Setup
on page3.
For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the
Extron Safety and Regulatory Compliance Guide on the Extron website.