Extron electronics HD CTL 100 User manual

IMPORTANT:
Go to www.extron.com for the
complete user guide, installation
instructions, and specifications.
HD CTL 100 Workspace Controller • Setup Guide
Attaching a Logitech®Tap
This supplementary setup guide provides instructions for
setting up the HD CTL 100 with the Logitech Tap.
The Extron HD CTL 100 is a compact workspace controller
designed for automatic display control in small meeting
rooms and huddle spaces. It features an HDMI pass-through
port that detects signal presence and can facilitate automatic
display power. When an active signal is connected to the
HDMI input from the Logitech Tap, the HD CTL 100
automatically turns on the display via CEC control. When
no signal is detected, the HD CTL 100 powers off the display
after a predetermined period.
NOTE: For more details about installation, conguration,
and operation, see the HD CTL 100 User Guide,
available at www.extron.com.
HD CTL 100 Panels
The front and rear panel connectors include:
POWER
12V
0.3A MAX
INPUT
OUTPUT
+V OUTDIGITAL I / O
HDMI/CECHDMI
G24
IR / S
SG
21G43G
AA BB CC DD EE FF
CONFIG
RSIGNAL
HD CTL 100
HH
II JJ
Rear Panel Front Panel
G
APower input connector EVoltage output connector HReset button
BHDMI input connector FIR/S control connector IUSB configuration port
CHDMI/CEC output connector GPower LED JSignal LED
DDigital I/O ports
Figure 1. HD CTL 100 Rear and Front Panels
Connecting the Logitech Tap to the HD CTL 100
1. Connect the supplied Logitech power supply to the Tap Power connector (see figure2).
HDMI
POWER
USB-C
USB-A
Power USB-C HDMI USB-A
Figure 2. Tap Rear Connections
1
2
1
Example of Logitech Tap Room Setup
POWER
12V
0.3AMAX
INPUT
OUTPUT
+VOUT
DIGITALI/ O
HDMI
G24
IR/S
SG
21 G 43 G
HDMI/CEC
RegionalSales
0
30
60
90
120
150 SOUTH
NORTH
EAST
WEST
Logitech Tap
Laptop
(HDMI)
HD CTL 100
(HDMI & CEC)
logitech
logitech
Logitech
MeetUp
Intel NUC
logitech

HD CTL 100 with Logitech Tap • Setup Guide (Continued)
2
2. If needed, the Tap offers the ability for external source devices to be presented on the presentation display, by connecting a
source device, such as a laptop, to the HDMI connector of the Tap.
NOTE: Figure 4 and figure5 show the Logitech MeetUp Camera connected to the Intel NUC. The USB-A port on the
Tap can also be used for the camera connection if desired.
4. Connect the supplied Logitech Strong (USB-C to USB-A) cable from the Tap USB-C connection (see figure2) to one of the
Intel NUC USB-A connectors (see figure3).
HDMI
SS
19V
-+
HDMI
Out
USB-A USB-C
LANPower
Figure 3. Intel NUC Connections
5. For a Single Display system, connect an HDMI cable from the Intel NUC HDMI Out connector to the HD CTL 100 Input
connector (see figure3 and figure4).
POWER
12V
0.3A MAX
INPUT
OUTPUT
+V OUTDIGITAL I / O
HDMI/CECHDMI
G24
IR / S
SG
21G 43G
HD CTL 100
HDMI
HDMI
Display
Laptop
HDMI/CEC
Logitech MeetUp
USB
Intel NUC
HDMI
SS
19V
-+
Logitech Strong Cable
(USB-C to USB-A)
Logitech Tap
y
Di l
logitech
logitech
Figure 4. HD CTL 100 Cabling Diagram (Single Display)
3
4

6. For a Dual Display system:
• A second HD CTL and an Extron USBC-HDM/6 (USB-C to HDMI) cable are needed for the second display.
• Connect an HDMI cable from the Intel NUC HDMI Out to the Input connector of one HD CTL 100.
• The USBC-HDM/6 cable is connected from the Intel NUC USB C connector to the HDMI Input connector on the second
HD CTL 100 (see figure3 and figure5).
POWER
12V
0.3A MAX
INPUT
OUTPUT
+V OUTDIGITAL I / O
HDMI/CECHDMI
G24
IR / S
SG
21G 43G
HD CTL 100
HDMI
Logitech Tap
DisplayDisplay
Laptop
HDMI/CEC
POWER
12V
0.3A MAX
INPUT
OUTPUT
+V OUTDIGITAL I / O
HDMI/CECHDMI
G24
IR / S
SG
21G 43G
HDMI/CEC
HD CTL 100
Logitech
MeetUp
HDMI
SS
19V
-
+
HDMI USBC-HDM/6
USB
logitech
Di l
MODEL80
FLATPA NEL
Di l
D
MODEL80
FLATPA NEL
itech
ogitech
logitec
ogitec
logitech
L
Intel NUC
Logitech Strong Cable
(USB-C to USB-A)
Figure 5. HD CTL 100 Cabling Diagram (Dual Display)
NOTE: Figure4 and gure5 show the laptop (source device), the Logitech Tap, the Intel NUC, HD CTL 100(s), a Logitech
MeetUp camera, and the display(s). Each display is controlled via CEC. For displays that have limited or no CEC control,
use software to congure the HD CTL 100 to communicate to the display via IR or one-way serial control.
5 figure 5
3

HD CTL 100 with Logitech Tap • Setup Guide (Continued)
Logitech Tap System Setup Configuration
1. With the Intel NUC power ON, select the More icon (1) on the right of the Tap main presentation window.
2. Select Settings (2). (Enter Admin credentials if needed.)
3. Select Windows Settings (3) from the menu on the left of the screen.
4. From the window to the right of that screen, select Go to Admin Sign-in (4).
4

5. On the Windows login page, select the appropriate user account to sign in as administrator and enter Admin credentials.
Select the Right Arrow (5) when done.
6. From the Windows Start menu in the lower left corner, select Settings (6) from the list of applications.
7. Select System (7).
8. To ensure the system turns off the presentation display when not in use, select Power &sleep on the System menu.
The Screen time (8) for display can be set to any specific value. The suggested Screen time is 10 minutes and the
suggested setting for Sleep is Never.
9. The Intel NUC outputs a wake display signal to the HD CTL 100 when the Logitech Tap detects motion from the frontward
located sensor. The HD CTL 100 then sends a power command to the display, and the Main Skype Room screen is displayed
on the display monitor.
NOTE: Plugging in a source device, such as a laptop, when the screen is in sleep mode, does not wake the Tap.
5

© 2019 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876
68-3064-53 Rev. A
11 19
HD CTL 100 with Logitech Tap • Setup Guide (Continued)
For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the
Extron Safety and Regulatory Compliance Guide on the Extron website.