Extron electronics DTP R HWP 4K D series User manual

IMPORTANT:
Go to www.extron.com for the complete
user guide, installation instructions, and
specifications before connecting the
product to the power source.
1
DTP R HWP 4K D Series • Setup Guide
This setup guide provides instructions for an experienced installer to set up and operate the Extron DTP R HWP 4K 231 D and
DTP R HWP 4K 331 D extenders.
Installation
Step 1 — Disconnect Power
Disconnect all equipment power sources.
Step 2 — Prepare the Mounting Surface
ATTENTION:
• Installation and service must be performed by authorized personnel.
• L’installation et l’entretien doivent être effectués par le personnel autorisé uniquement.
• The unit must be installed in accordance with the National Electrical Code and with local electrical and safety
codes.
• L’unité doit être installée conformément au National Electric Code et aux normes électriques et de sécurité locales.
NOTE: Use the included mud ring (MR 200) or a UL approved 1-gang RACO wall box (not supplied) with a depth of at
least 3.0 inches (7.6 cm). For more information, see the full product user guide at www.extron.com.
a. Place either the mud ring (see gure on page 1) or the wall box (see gure on page 2) against the installation surface and
mark the opening guidelines.
TIP: Use a level to mark the opening.
b. Cut out the material from the marked area.
c. Either:
• Insert the mud ring into the opening, rotate the locking
arms, and secure it with the supplied screws,
or
• Secure the wall box to the wall stud with 10-penny nails
or #8 or #10 screws, leaving the front edge ush with the
surface.
TLP 1000T
V
IN1608
100-240V~ -- A MAX
1
2
CONFIGURABLE
HDMIHDMI
5
6
78
C
RS-232 IR
RS-232 IR
Tx Rx Tx RxG
Tx Rx Tx RxG Tx Rx Tx RxG
HDMI
A
B
3
4
INPUTS OUTPUTS
Tx Rx
RS-232
G
LAN
2x25W(8Ω)/2x50W(4Ω)
RESET
AUDIO INPUTS OUTPUTS
REMOTE
LL1R R
L2 R
L
3
R
CLASS2 WIRING
L4R
L5R
+48V
+48V
12
LR
VARIABLE
IN1608SA
2
MIC/LINE
L6R
SIG LINK
DTPIN
SIG LINK
DTPIN
SIG LINK
DTPOUT
50/60Hz
RS-232 IR
OVERDTP
OVERDTP
OVERDTP
AMPLIFIED OUTPUT
VOLUME
SCALINGPRESENTATION SWITCHER
IN1608
INPUTS
1
HDCP
SIGNAL
OUTPUTS
ENTER
MENU
Extron
2 3 4 5 6 7 8 A B C
INPUTS
1 2 3 4 5 6 7 8
CONFIG
Extron
DTP T UWP 232 D
Transmitter
Extron
DTP T HWP 232 D
Transmitter
Extron
DTP R HWP 4K 331 D
Receiver
Ethernet
Network
XTP DTP 24 Cable
230'
AUTOSW
CONFIG
IROUT
HDMI IN
AUDIO IN
S
G
HDCP
1
AUDIO IN
VGA IN
AUTOSW
CONFIG
IROUT
HDMI IN
AUDIO IN
S
G
HDCP
1
HDMI IN
AUDIO IN
HDCP
1
2
HDMI OUT
G
Tx Rx
Tx Rx
OVERDTP
RS-232 IR
Projector
HDMI
IPCP PRO 550
21 LIMIT
RIR
Tx
Rx
Tx
Rx
RTS
CTS
COM
IR/SERIALRELAYS FLEX
I/O
SLIMIT
eBUS
SWITCHED
12 VDC
1000
LINK
ACT
IPCP PRO 550
OVER 4312345678 OVER 5678
21
34
2134
5678
2134
Rotate locking arm
and insert into wall
opening.
Mud Ring

2
DTP R HWP D 4K Series • Setup Guide (Continued)
d. Run all required cables (see steps 3, 4, and 5),
thread the cables through the mud ring or walll
box, and secure them with cable clamps.
TIP: In order to t the unit in the junction
box, do not install boots on TP cables
and RJ-45 connectors.
Step 3 — Run Cables Between Units
Connect the rear panel transmitter output to a rear panel receiver input using twisted pair cable.
Wire the cable as shown in the diagram to the right.
For optimal performance, Extron highly recommends the following:
• RJ-45 termination with shielded twisted pair cable must comply with TIA/EIA-T568B
wiring standard for all connections. For more information on TP cable wiring and
termination, see the DTP R HWP 4K 231 and 331 D User Guide at www.extron.com.
• Use shielded twisted pair cable, 24 AWG solid conductor or better, with a minimum cable
bandwidth of 400 MHz.
ATTENTION:
• Do not use Extron UTP23SF-4 Enhanced Skew-Free AV UTP cable to link the device with DTP transmitters or
receivers.
• N’utilisez pas le câble AV Skew-FreeUTP version améliorée UTP23SF d’Extron ou le câble STP201 pour relier
le appareil avec les émetteurs ou les récepteurs DTP.
NOTE: Extron XTP DTP 24 Shielded twisted pair cable is strongly recommended for
optimal performance.
• Use shielded RJ-45 plugs to terminate the cable.
• Limit the use of RJ-45 patches. Overall transmission distance capabilities vary
depending on the number of patches used. If possible, limit the number of patches to
two total.
• If RJ-45 patches must be used in the system, shielded patches are recommended.
Step 4 — Connect Output Device
Front Panel
A DTP RS-232 and IR connectors — To pass serial or infrared data or control signals,
such as serial control of a projector, connect the master device to the transmitter and
the slave device to the receiver via the RS-232 and IR captive screw connectors on both
units.
B HDMI output connector — Connect an HDMI cable between this port and the input on
a sink device.
HDMI OUT
Extron
OVER DTP
A
B
DTP R HWP 4K 231 D
and DTP R HWP 4K 331 D
Front Panel
5
Pin
1
2
3
6
7
8
4
Wire color
White-green
Green
White-orange
White-blue
Orange
White-brown
Brown
Blue
TIA/EIA
T568-B
TP Wires
12345678
Pins:
Wall Stud
Screws
or Nails
Signal
Output
Cabl
e
Decora Faceplate
Extron
DTP R HWP 4K 231 D
HDMI OUT
Extron
OVER DTP

3
DTP R HWP D 4K Series • Setup Guide (Continued)
Rear Panel
A DC power input connector — Wire and plug the included external 12 VDC power supply into either this 2-pole
connector or the power input connector on the transmitter (see the DTP R HWP 4K 231 and 331 D User Guide at
www.extron.com for wiring information).
B DTP IN connector — Connect the opposite end of the twisted pair cable from the
transmitter output connector to this RJ-45 connector.
ATTENTION:
• Do not connect these outputs to a telecommunications or computer
data network.
• Ne connectez pas ces appareils à des données informatiques ou à un
réseau de télécommunications.
NOTES:
• The DTP R HWP 4K 231 D models can receive video, control, and audio (if
applicable) signals up to 230 feet (70 meters).
• The DTP R HWP 4K 331 D models can receive video, control, and audio (if
applicable) signals up to 330 feet (100 meters).
Signal LED — Lights when the unit is receiving any valid signal on the DTP In connector.
Link LED — Link is established between the units on the DTP cable.
C Audio Output connector — Connect a balanced or unbalanced stereo or mono audio device to the receiver via the
Audio captive screw connector. See the drawing below.
Tip
Ring
Sleeve (s)
Tip
Ring
Tip
Sleeve (s
)
Tip
See Caution
See Caution
LR
LR
Unbalanced Balanced
CAUTION: For unbalanced audio, connect the sleeves to the ground contact. DO NOT connect the sleeves to the
negative (–) contacts.
ATTENTION : Pour l’audio asymétrique, connectez les manchons au contact au sol. Ne PAS connecter les
manchons aux contacts négatifs (–).
Step 5 — Power the Units
The units can be powered one of two ways:
• Locally with the included power supply. A compatible transmitter can then be powered remotely through the DTP line.
• Remotely via the DTP line by a locally powered DTP transmitter.
NOTE: See the DTP R HWP 4K 231 and 331 D User Guide at www.extron.com for wiring information.
Step 6 — Final Installation
a. Make all connections, power the units, and test the system for satisfactory operation.
b. At the power outlet, unplug the power supply.
c. Mount the receiver into the wall box, and attach the supplied Decora® faceplate to the unit.
d. At the power outlet, reconnect the power supply to power up both units.
SIG LINK
DTP IN
AUDIO
POWER
12V
A MAX
LR
- -
DTP IN
DTP R HWP 4K 231 D
A
BC
DTP R HWP 4K 231 D
and DTP R HWP 4K 331 D
Rear Panel

68-2816-50 Rev. A
04 16
Extron Headquarters
+1.800.633.9876 (Inside USA/Canada Only)
Extron USA - West Extron USA - East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX [phone] FAX
Extron Europe
+800.3987.6673
(Inside Europe Only)
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.299.1800
+971.4.299.1880 FAX
Extron Australia
+61.8.8351.2188
+61.8.8351.2511 FAX
Extron India
1800.3070.3777
(Inside India Only)
+91.80.3055.3777
+91.80.3055.3737 FAX
© 2016 Extron Electronics All rights reserved. www.extron.com
Operation
After all devices are powered up, the system is fully operational.
Receiver LED
A Power LED —
Amber — The unit is receiving power, either locally or remotely (on the DTP cable).
Green — The unit is powered on and is receiving an active HDMI signal, transmitted on the
DTP cable.
If any problems are encountered, verify that the cables are routed and connected properly. If
your problems persist, call the Extron S3 Sales and Technical Support Hotline that is
closest to you, at the number shown below.
HDMI OUT
Extron
OVER DTP
DTP R HWP 4K 231 D
and DTP R HWP 4K 331 D
Front Panel
A