Extron electronics DSC HD-3G A User manual

1
IMPORTANT:
Go to www.extron.com for the complete
user guide,
installation instructions,
and
specifications bef
ore connecting the
pr
oduct to the po
wer source.
DSC HD-3G A Scaler • Setup Guide
The Extron DSC HD-3G A is an HDMI to 3G-SDI scaler that converts HDMI signals to 3G-SDI, HD-SDI, and SD-SDI. It accepts
computer and SMPTE video resolutions up to 1920x1200 and 2K, and offers multiple output rates from 480i up to HDTV
1080p @ 60 Hz and 2K. The DSC HD-3G A features advanced Extron video signal processing with 1080i deinterlacing and Deep
Color processing for optimal image quality. Dual SDI outputs, stereo audio embedding, and genlock are also provided. This
setup guide provides step-by-step instructions for an experienced user to set up and configure a DSC HD-3G A. It covers how to
perform basic operations using the front panel controls and selected Simple Instruction Set™(SIS™) commands.
NOTE: For full installation, configuration, menu, connector wiring, and operation details, see the DSC 3G-HD A and
DSC HD-3G A User Guide, available at www.extron.com.
Installation
Rear Panel Features
Mounting and Cabling the DSC HD-3G A
1. Disconnect power — Turn off or disconnect all equipment power sources.
2. Mount the unit: (Optional) Mount the DSC HD-3G A either in a rack using
shelf mounting brackets (RSU 129 or RSB 129) or under furniture using
furniture mounting brackets (MBU 125) (see gures 1 and 2 at right). A false
half-rack faceplate can be tted next to the DSC if desired.
3. Connect the input — Connect an HDMI video source to the HDMI input
connector C.
4. Connect analog audio input — (Optional) Connect analog audio from the
source to the captive screw audio input connector B.
NOTE: To embed audio from this input, set it up using the on-screen
display (OSD) (see page 2) or SIS commands (see page 4).
5. Connect the output — Connect one or two SDI display devices to the
3G/HD/SD-SDI output connectors Efor SDI output with optional embedded
analog or HDMI audio.
6. Connect a sync device — (Optional) Attach an external sync device
to the input (right) Sync connector (D). Connect any downstream
device to be synchronized by genlocking to the output (left) Sync
connector (D).
7. Connect a control device — For remote control via SIS commands
or the PCS Windows®-based control software:
zRS-232 — For serial RS-232 control, connect a host computer or
control system to the 3-pole captive screw RS-232 connector F.
RS-232 protocol default values are 9600 baud, 1 stop bit, no
parity, 8 data bits, no ow control.
zUSB — Connect a host computer or control system to the front
panel mini USB port (Bin the front panel illustration on page 2)
for conguration and control via Extron PCS software.
8. AC power connector — Connect the supplied US IEC power cord
to this connector Afrom a 110-220 V, 50-60 Hz AC, power source.
Figure 2. Under-furniture Mounting
DVC 501 SD
DIGITALVIDEO CONVERTER
(2) 4-40 x 3/16" screws
Use 2 mounting holes on
opposite corners.
Half-rack
false front panel
uses 2 front holes.
AAC power connector
B5-pole captive screw audio input
connector
CHDMI video input connector
DGenlock sync connectors
E3G/HD/SD-SDI output connectors
F3-pole RS-232 captive screw
connector
AA B
BCCD
DE
EF
F
100-240V ~ .3A MAX
50-60 Hz
DSC HD-3G A
REMOTEOUTPUT
LR
HDMI 3G/HD/SD-SDI
SYNC
AUDIO
INPUT
GENLOCK
RS-232
Tx Rx G
MBU 125 Mounting Bracket
#8 Screw
(4) Places
Each Side
Mounting
Screws
(2) Places
Each Side
Figure 1. Rack Mounting

DSC HD-3G A • Setup Guide (Continued)
2
Front Panel Overview
DSC HD-3G A
AUTO-
IMAGE
ExtronMENU
ENTER HOLD FOR 720p 1080i
INPUT OUTPUT
SYNC
2.97 Gbps
1.485 Gbps
270 Mbps
SIGNAL
2CH-LPCM
MULTI-CH PCM
ANALOG
CONFIG
AA B
BC
CDD EE FF
AStatus LED — Lights amber steadily when there is power but no signal, blinks amber every 3 seconds when the unit is in
standby mode, and lights green steadily when both power and an input signal are present.
BUSB configuration port — Connect a control system or computer to this mini USB port (cable not supplied) for device
configuration, control, and firmware upgrading.
CInput LEDs — The Signal LED lights to indicate presence of an HDMI input signal. An audio signal LED (2CH-LPCM, Multi-
CH PCM, or Analog) lights to indicate the type of audio signal (two-channel LPCM, multi-channel PCM, or analog) if present.
DOutput LEDs — Light to indicate the presence of sync and the rate specified for the output:
zSync: Sync is present (does not light if video sync is muted).
z2.97 Gbps: SMPTE 424M
z1.485 Gbps: SMPTE 292M
z270 Mbps: SMPTE 259M
EMenu and Enter buttons — Let you access the OSD and select submenus and items from the menus.
FNavigation buttons — Press these right , left , up , and down arrow buttons to step through the OSD
submenus, to lock the front panel (see the next section), perform Auto-Image (press ), and reset the output rate (hold for
5 seconds).
Locking the Front Panel (Executive Mode)
To prevent unauthorized access or accidental changes to DSC settings, you can lock the front panel controls, making control
available only by SIS commands. (The default state is unlocked.) You can lock and unlock the front panel as follows:
zUsing the front panel buttons: To lock, press the Menu and buttons simultaneously and hold them until the OSD
displays Executive Mode Enabled (approximately 5 seconds). To unlock, repeat this process.
zSIS commands: To lock (enable executive mode), enter 1X. To unlock (disable executive mode), enter 0X.
Configuring the DSC HD-3G A
The DSC HD-3G A can be configured through a host connected to
the RS-232 or USB port, using Extron PCS configuration software
(available at no charge at www.extron.com) or SIS commands
(see page 4 for a selection of basic commands). You can also
configure it using the OSD menu system, described below.
On-Screen Display (OSD) Menu System
The OSD menu system consists of seven submenus and two
information screens. To access the menus, press the front panel
Menu button. With the main menu displayed, use the arrow
buttons to step through the submenus and submenu items.
Press the Enter button to select the item that you highlight. The
Communication and Device Info screens are read-only and do
not provide selections.
•Quick Setup •User Presets •Picture Controls
•Input •Output •Audio
•Advanced •Communication •Device Info
NOTE: The OSD times out and closes after 1 minute if no
buttons are pressed.

To use any menu:
1. Press the Menu button to access the main menu. The menu opens with the Quick Setup menu shown on the display device.
2. Press the and buttons repeatedly to cycle through to the desired submenu (each button press outlines the next item).
3. Press the Enter button to access the desired submenu. The rst item is outlined in yellow.
4. Press the and buttons to cycle through the items of the selected submenu until the desired item is outlined.
5. Press the Enter button to select the outlined item (the selected item is highlighted).
6. Press the and buttons to adjust the values within the item. For the items on the Picture Controls submenu, press the right
or left arrow button to select the item on the right or left, then press the and buttons to adjust the settings.
7. Press the Enter button to conrm your changes. The yellow highlighting is replaced by the yellow outline on the submenu screen.
8. Press the or to move to another submenu item or press the Menu button to exit the submenu. To exit the menu system, press
the Menu button twice.
Setting Up the DSC HD-3G A Using the OSD Menu
The Quick Setup submenu is displayed when the OSD opens. Use this submenu to perform a basic system setup and get
started quickly using the DSC. Select the following items from it as needed:
zAuto-Image™ — Performs an Auto-Image on the video input to adjust the horizontal and vertical size and positioning to the
selected aspect ratio (ll the screen or follow the input device aspect ratio). To perform an Auto-Image, select this item, then
press Enter again to initiate the Auto-Image.
zInput EDID — Matches the input EDID (extended display identication data) to the output rate or sets a discrete EDID. After
selecting Input EDID, press the or button to view the available EDIDs (the default is to match the DSC output rate).
zOutput Resolution — Lets you select the resolution and refresh rate for the current output from 42 available
factory-installed rates (see "Output Scaler Rates"). Select the Output Resolution submenu, then press the and 
buttons to cycle through the available rates.
zAuto Memory — Sets the DSC to automatically save the current input conguration and picture control values according
to the most recent conguration for each different rate. After selecting Auto Memory, press any arrow button to toggle Auto
Memories on and off.
zAspect Ratio — Lets you specify how much of the display the image lls. The submenu items are Fill (lls the entire
screen) or Follow (uses the aspect ratio of the input). After selecting Aspect Ratio, press any arrow button to toggle
between Fill and Follow.
zInput Audio Format — Lets you select the format of the audio to embed in the output. After selecting Input Audio
Format, press any arrow button to cycle through the items: None (mute the audio), Analog (embed analog audio onto the
SDI output), LPCM-2CH (use the rst channel pair), Multi-Ch (use the rst four channel pairs).
zTest Pattern — Lets you select from seven test patterns to aid in setting up the DSC and the output display.
Output Scaler Rates
Output rates can be set using the OSD menu or SIS commands. The table below gives the rates and their SIS variables (see
page 4 for the commands).
SIS Variables for DSC HD-3G A Resolutions and Refresh Rates (X2) = 68 through 303)
Resolution 23.98 Hz 24 Hz 25 Hz 29.97 Hz 30 Hz 50 Hz 59.94 Hz 60 Hz
480i 93
576i 94
720p 95 96 68 69 70 71 72* 73
1080i 74 75 76
1080p 77 78 79 80 81
1080p (level A) 82 83 84
1080p (level B) 301 302 303
2048x1080 (2K) 85 86 87 88 89 90 91 92
*Default output resolution
Output Rate Reset
If an image cannot be displayed due to an incompatible output rate, you can reset the output rate as follows:
With the OSD closed, press and hold the button for approximately 5 seconds to toggle between 1080i @ 59.94 Hz and
720p @ 59.94 Hz.
3

DSC HD-3G A • Setup Guide (Continued)
NOTE: X# = Input video format: 0= no signal; 1= HDMI, 2= DVI, 3= invalid signal (up to 30 Hz);
4 = 3G-SDI 1080p (@ 50, 59.94, and 60 Hz), 2K; 5= unknown.
X2) = Output scaler rate: 0= automatic (match output rate), 1= custom rate 1, 2= custom rate 2, 3= custom rate 3,
9 = match input (see the SIS variables table on page 3 for more rate variables).
X2* = Output sync timeout duration in seconds (1-500 in 1-second increments): 501 = never (default), 0= immediate timeout
X4) = Screen saver mode: 1= black (default), 2= blue
X4@ = Video mute: 0= off (unmuted), 1= on (muted to black screen), 2= on (all output sync and video muted)
X6@ = Power save setting: 0= full power (default), 1= low power state
X6# = Screen saver status: 0= active, timer not running; 1= no active input, timer running, output sync active;
2= No active input, timer expired
Extron Headquarters
+1.800.633.9876 (Inside USA/Canada Only)
Extron Asia
+65.6383.4400
Extron China
+86.21.3760.1568
Extron Korea
+82.2.3444.1571
Extron Europe
+31.33.453.4040
Extron Japan
+81.3.3511.7655
Extron Middle East
+971.4.2991800
Extron India
+91.80.3055.3777
© 2015 Extron Electronics — All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
Basic SIS Commands
The DSC HD-3G A can be configured with specific SIS commands via RS-232 or USB connection. This table lists a selection
of basic commands (all responses to View commands are shown in verbose mode with tagged responses). For a full list of SIS
commands and variables see the DSC 3G-HD A and DSC HD-3G A User Guide, online at www.extron.com.
Command ASCII Command
(Host to Scaler)
Response
(Scaler to Host) Additional Description
View input video format 1*\Vtyp 1*X# ]View detected input video format X#.
Audio Input Format — select between analog (5-pole captive screw connector) and digital (embedded in HDMI input) audio sources.
Set to none EI1*0AFMT }Afmt I1*0]Mute all audio for the input.
Set to analog EI1*1AFMT }Afmt I1*1]Select analog audio for the input.
Set to LPCM-2CH digital EI1*2AFMT }Afmt I1*2]Select LPCM 2-channel digital audio for the input (default).
Set to Multi-CH digital EI1*3 AFMT }Afmt I1*3]Select multi-channel digital audio for the input.
Execute Auto-Image AImg ]Perform an Auto-Image on the current input.
Output Configuration
Set output scaler rate EX2) RATE }Rate X2) ]Select output resolution and refresh rate X2) (see the
output SIS variables table on page 3).
View output rate ERATE }Rate X2) ]Show the current output rate for the DSC HD-3G A.
Video Mute (Defaults to unmuted after a power cycle.)
Mute video to black 1*1B Vmt 1 *1]Mute the video and display a black screen.
Mute video and output sync 1*2B Vmt 1 *2]Mute all TMDS signals on the SDI video output.
Unmute video 1*0B Vmt 1 *0]Unmute the output video.
View video mute status 1B Vmt 1 *X4@ ]View output video mute status (X4@).
Screen Saver Mode (Active when no signal is detected on the input)
Set screen saver mode EMX4) SSAV }Ssav MX4) ]Set the screen saver mode to X4) (default = 1 = black).
View screen saver mode EMSSAV }Ssav MX4) ]View current screen saver mode X4).
Set sync timeout duration ETX2* SSAV }Ssav TX2* ]Set the period before sync timeout to X2* seconds
(default = 501 = never).
View sync timeout duration ETSSAV }Ssav TX2* ]View the amount of time X2* before sync timeout.
View screen saver status ESSSAV }Ssav SX6# ]View the screen saver status X6#.
Reset device to factory settings EZXXX }Zpx ]Resets all device settings to the factory defaults.
Power Save Mode
Power save off E0PSAV }Psav 0]Set the DSC to run in full power mode (default).
Power save on E1PSAV }Psav 1]Place the DSC in low power mode. (This mode can be
exited only via the E0PSAV }command or by cycling
power to the unit.)
View power save setting EPSAV }Psav X6@ ]View power save status X6@.
4
68-2261-50 Rev. B
07 15