Extron electronics DVC 501 SD User manual

Product Category
1
DVC 501 SD • Setup Guide
The Extron DVC 501 SD receives SD-SDI, HD-SDI, and 3G-SDI serial digital video signals and converts them to DVI-D and
analog RGB or component video. It is compliant with SMPTE 259M, 292M, 424M, and ITU digital video standards. The RGB
output can be set for RGBHV, RGBS, and RGsB. Bi-level or tri-level sync can be selected when the unit is set for component
video output. The DVC 501 SD features extraction of embedded AES3 audio, RS-232 and USB serial control, and a buffered
loop-through that delivers reshaped and restored multi-rate SDI signals.
NOTE: For full installation, configuration, and operation details, see the DVC 501 SD User Guide, available at
www.extron.com.
Rear Panel Features and Connections
100-240V ~ 0.3A MAX
50/60 Hz
3G / HD / SD-SDI
BUFFERED
INPUT
LOOP-THROUGH RGB/R-Y,Y,B-Y
OUTPUT
DVI-D
LR
RS-232
N/A Tx Rx
AUDIO
12456
3
7
aAC power connector dDVI-D output connector fAudio output connector
b3G/HD/SD-SDI input connector eRGB/YUV output connector gRS-232 connector
cBuffered Loop-through connector
Installation Steps
1. Disconnect power from all equipment.
2. (Optional) Mount the unit to a rack or furniture.
3. Connect the video input. Connect an SD-SDI, HD-SDI, or 3G-SDI source to the 3G/HD/SD-SDI port of the BNC input
connector (bin the rear panel illustration above).
4. (Optional) Connect a monitor or recording device. Attach a monitor or video recording device to the Buffered
Loop-through BNC connector (c).
5. Connect the video output. Connect a display or other output device to the DVD-D digital video connector (d) or to
the RGB/R-Y,Y,B-Y analog RGB (RGBHV, RGBS, and RGsB) or YUV component video connector (e).
6. Connect a control device. Connect a host device, such as a computer or touchpanel control system to one or both of
the following DVC ports to configure and control the DVC via Simple Instruction Set (SIS™) commands.
zRS-232 port (rear panel) — Connect a host device to the Tx, Rx, and _(ground) pins of this 5-pole captive screw
connector (g). The first and second pins of this connector are not used. The default protocol for this port is
9600 baud, 1 stop bit, no parity, 8 data bits, and no flow control.
zCong port (front panel) — Connect a USB cable (USB A to USB mini B) between a USB port on your computer
and this port (aon the front panel illustration on the next page).
7. Connect the audio output. Connect an amplifier or other audio output device to the 5-pole captive screw audio
connector (fon the rear panel illustration), as shown below.
Do not tin the wires!
Balanced Audio Output
Tip
Ring
Tip
Ring
LR
Sleeves
Unbalanced Audio Output
Tip
Tip
LR
Sleeves
CAUTION: For unbalanced audio, connect the sleeves to the ground contact. DO NOT connect them to negative (–)
contacts.
8. Connect power to the DVC 501 SD by plugging a standard IEC power cord (provided) from a 100 to 240 VAC, 50-60 Hz
power source into the power receptacle (a).

68-1518-50 Rev. C
09 11
2©2011 Extron Electronics All rights reserved. www.extron.com
Front Panel Features
Extron
NEXT
MENU
DVC 501 SD
DIGITAL VIDEO CONVERTER
ADJUST
CONFIG
1235
4
aUSB Config port bLCD screen cMenu button dNext button eAdjust knobs
Conguring the DVC 501 SD Using the Front Panel
Menu selections are displayed on the LCD screen. To use any menu, press the Menu button repeatedly until the desired
menu is displayed (see the menu flow diagram below). Press the Next button repeatedly until the desired submenu appears.
Rotate an Adjust knob to select an item from a submenu. To return to the main menu at any time, press the Menu button.
After 30 seconds of inactivity, the screen displays the default cycle.
1. From the Output Config submenus, use the Adjust knobs to select the output signal
type and the sync polarity to match the requirements of the display device.
2. From the Advanced Config menu, Test Pattern submenu, select the Crop, Crosshatch,
Colorbars, and Grayscale test patterns to confirm that the settings of the display device
are correct.
NOTE: Test pattern timings are based on the incoming SDI signals and are not
displayed if an active signal is not present.
3. Use the Audio Config submenus to configure the audio as desired.
Supported Input Resolutions
Supported
Resolutions 23.98 Hz 24 Hz 25 Hz 29.97 Hz 30 Hz 50 Hz 59.94 Hz 60 Hz
720p X X X X X X
1080i X X X
1080p X X X X X X X X
NTSC X
PAL X
NOTE: The output resolution always matches the input resolution.
Simple Instruction Set (SIS) Commands
When setting up the DVC 501 SD, you can issue SIS commands from your computer via RS-232 or USB as an alternative to
the front panel controls. See the DVC 501 SD Series User Guide for a complete list of available SIS commands.
Command ASCII command
(Host to Converter)
Response
(Converter to Host) Additional Description
Mute video 1B Vmt1]Mute the video output.
Unmute video 0B Vmt0 ]Display the video output.
Mute audio 1Z Amt1 ]Mute the audio output.
Unmute audio 0Z Amt0 ]Unmute the audio output.
Enable lock (executive) mode 1X Exe1]Lock all front panel functions.
Disable lock mode 0X Exe0 ]Enable all front panel functions.
AUDIO
CONFIG
30 sec.
Default
Cycle
Menu
EXIT MENU
PRESS NEXT
OUTPUT
CONFIG 30 sec.
30 sec.
Menu
ADVANCED
CONFIG
30 sec.
Menu
Menu
Menu
Next