Extron electronics HAE 100 4K Plus User manual

HAE 100 4K Plus •Setup Guide
The Extron HAE 100 4K Plus is an audio de-embedder that extracts the audio from an HDMI signal, including audio from 4K sources.
The HAE 100 4K Plus provides an analog output for stereo or dual mono signals, as well as a S/PDIF digital audio output that
supports two-channel or digital multi-channel signals.
Mounting
The HAE 100 4K Plus can be placed on a desktop or tabletop using the included rubber feet, or mounted to a rack or furniture (see
the HAE 100 4K Plus User Guide, available at www.extron.com, for mounting options and instructions).
Cabling
Rear Panel Features and Cabling
SIGNAL
IN OUT
CONFIG
HDCP
AUDIO IN
2-CH LPCM
BITSTREAM
HAE 100 4K PLUS
HAE 100 4K PLUS
12V
0.6A MAX
POWER
INPUT OUTPUT AUDIO OUTPUTS
S/PDIF ANALOG
LR
BB EE CC
AA DD
AA BB DD
CC
Figure 1. HAE 100 4K Plus Rear Panel
APower input — Connect the provided power supply to the 3.5 mm, 2-pole captive
screw power receptacle (see the image at right).
ATTENTION:
• Do not connect the power supply before reading the Attention in the Power
Supply section of the HAE 100 4K Plus User Guide.
• Ne branchez pas la source d’alimentation externes avant d’avoir lu les mises
en garde dans la section «PowerSupply» du HAE 100 4K Plus User Guide.
BHDMI input — Connect an HDMI input source into this female HDMI type A connector.
NOTE: By default, the EDID stored at the HDMI input is set to 1080p at 60 Hz with 2-channel audio. EDID can be
congured using Extron PCS software (see Configuration on the next page).
CHDMI output — Connect an HDMI output device into this female HDMI type A connector.
NOTE: It is not required to connect an HDMI output device to extract audio from the HDMI input signal.
DS/PDIF audio output — Connect a S/PDIF audio output device into this female RCA connector. This connector outputs digital
S/PDIF audio formats (2-channel LPCM, Dolby Digital, or DTS) that are extracted from the HDMI input signal.
EAnalog audio output — Connect an audio output device to this 5-pole, 3.5 mm captive screw connector (see figure 2 below for
connector wiring). This connector outputs 2-channel LPCM (converted to analog) that is extracted from the HDMI input signal.
Do not tin the wires!
Balanced Audio Output
Tip
Ring
Tip
Ring
Sleeves
Unbalanced Audio Output
Tip
No Ground Here
No Ground Here
Tip
Sleeves
LR
LR
Figure 2. Analog Output Connector Wiring
ATTENTION:
• Connect the sleeve to the ground (Gnd) terminal. Connecting the sleeve to a negative (-) terminal will damage the
audio output circuits.
• Connectez le manchon à la terminaison terre (Gnd). Connecter le manchon à une terminaison négative (-)
endommagera les circuits de la sortie audio.
SECTION A–A
AA
Power Supply
Output Cord
Captive Screw
Connector
Ridges
Smooth
3/16"
(5 mm) Max.

Front Panel Features and Cabling
SIGNAL
IN OUT
CONFIG
HDCP
AUDIO IN
2-CH LPCM
BITSTREAM
HAE 100 4K PLUS
HAE 100 4K PLUS
12V
0.6A MAX
POWER
INPUT OUTPUT AUDIO OUTPUTS
S/PDIF ANALOG
LR
BB EE CC
AA DD
AA BB DD
CC
Figure 3. HAE 100 4K Plus Front Panel
APower LED — The LED indicator lights when the unit is receiving power.
BConfig port — Connect a control PC to this female Mini-B USB Cong port to update the rmware, congure various
functions of the unit, and view the current status of the unit.
CInput and Output LEDs — These four LEDs provide the status of the HDMI input and output:
• Signal — Input LED lights when the unit is receiving a signal on the HDMI input.
Output LED lights when a sink device is connected to the HDMI output.
• HDCP — Input LED lights when the input signal is HDCP encrypted.
Output LED lights when an HDCP compliant sink device is detected and the output is encrypted.
DAudio input LEDs — These two LEDs provide the status of the various audio input functions:
• 2-CH LPCM — This LED lights when the incoming embedded audio signal is a 2-channel Digital LPCM audio format.
• Bitstream — This LED lights when the incoming embedded audio signal is a Dolby Digital or DTS audio format.
Configuration
Several HAE 100 4K Plus features can be congured using Extron PCS software or SIS commands:
• Extron Product Configuration Software (PCS): To congure the unit using PCS, download the software from
www.extron.com (see the HAE 100 4K Plus Series User Guide for details).
• Simple Instruction Set™ (SIS) commands: SIS commands can be sent from a PC to the HAE 100 4K Plus using Extron
DataViewer or other command interface (see the “SIS Commands” section of the HAE 100 4K Plus Series User Guide).
68-3113-50
Rev. A
03 20
© 2020 Extron Electronics — All rights reserved. www.extron.com
All trademarks mentioned are the property of their respective owners.
Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876
For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the
Extron Safety and Regulatory Compliance Guide on the Extron website.