Extron electronics MTP R 15HD RSA D User manual

Setup Guide — MTP R 15HD RSA D
This guide provides basic instructions for an
experienced installer to set up and operate the
Extron MTP R 15HD RSA D receiver.
Pre-installation
The MTP R 15HD RSA D receiver can be
installed in a one-gang electrical wall box
with a Decora wall plate cover (supplied).
Choose a location that allows cable runs
without interference. Allow enough depth
for both the wall box and the cables. The
box should be at least 2.5” (6.4 cm) deep to
accommodate the connectors and cables.
Install the cables into the wall, furniture, or
conduits before installing the receiver.
Figure 1 details the recommended
termination of TP cables with RJ-45
connectors in accordance with the
TIA/EIA T568A or TIA/EIA T568B wiring
standards. You can use either standard
with CAT 5/5e/6 cable, but ensure that
you use the same standard on both ends of
the cable.
Power Supply Wiring (Figure 2)
Wire the power connector. Verify the
polarity before connection by pluging
in the power supply with no load and
checking the output with a voltmeter.
For more information and warnings,
see “Power supply wiring” in the
MTP R 15HD RSA D User’s manual.
Installation
Connect/Configure the Rear
Panel (Figure 3)
aDC power connector —
If applicable, plug the external
12 VDC power supply into this
2-pole captive screw connector. See
figure 2 for power wiring details.
b Input connector — Connect the TP
cable from the transmitter to this
pigtail RJ-45 female connector. See
Figure 1 to wire the RJ-45 connectors.
c DIP switches — Set the DIP switches
to the desired preference. See the
reverse side for more details.
5
Pin
1
2
3
6
7
8
4
Wire color
White-green
NOTE If you are using Enhanced
Skew-Free™ A/V cable, use the
TIA/EIA T568A standard only.
Green
White-orange
White-blue
Orange
White-brown
Brown
Wire color
T568A T568B
White-orange
Orange
White-green
White-blue
Green
White-brown
Brown
Blue Blue
Insert
TP Wires
Pins:
12345678
Power Supply
Output Cord
Captive Screw
Connector
35
SECTION A–A
Ridges
Smooth
A A
Tie Wrap
MTP 15HD RSA D Rx Rear Panel
INPUT
H SYNC +
V SYNC +
C SYNC
SOG
VIDEO
Bi-RS232
H SYNC +
V SYNC +
C SYNC
SOG
VIDEO
Bi-RS232
2
1
3
Figure 1 – TP Cable Termination
Figure 3 – Rear Panel Connections
Figure 2 – Power Connector Wiring

Extron USA - West
Headquarters
+800.633.9 876
Inside USA / Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron USA - East
+800.633.9 876
Inside USA / Canada Only
+1.919.86 3.1794
+1.919.86 3.1797 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.765 5
+81.3.3511.765 6 FAX
Extron China
+400.883.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.299180 0
+971.4.299188 0 FAX
© 2009 Extron Electronics. All rights reserved.
Setup Guide — MTP R 15HD RSA D (cont’d)
Set the DIP Switches
(Figures 3 and 4)
H Sync and V Sync switches — Set these
switches on (right) for positive sync or
off (left) for negative sync.
Composite Sync, SOG, and Video
switches — Set these switches as shown in
figure 3 to output the indicated format.
BI-RS232 — Set this switch on (right) to select
bidirectional communications when serial data
is present on the audio/RS-232 wire pair;
off (left) to select unidirectional
communications.
Mount the Receiver (Figure 5)
Before mounting, test the transmitter/receiver
system. Make any cabling adjustments
before final installation, as the cables will be
inaccessible afterwards.
After testing, do the following:
1. At the power outlet, unplug the power
supply.
2. Mount the receiver into the box, and attach
the supplied Decora faceplate to the unit.
3. At the power outlet, reconnect the power
supply.
Connect/Configure the Front Panel
(Figures 6 and 7)
d Output video connector — Connect a
projector or other high resolution video
device to this 15-pin HD connector.
e Audio/RS-232 output connector — Insert
a 3.5 mm, 5-pole captive screw connector
into this jack for mono audio and/or a RS-
232 serial output. See figure 7 for wiring
for wiring details.
f Level control — Adjust this control while
viewing the displayed image to set the
level/boost that provides the best picture
quality.
Peaking control — Adjust this control to
obtain the optimum picture sharpness.
g Power LED — This LED indicates power
is applied to the MTP.
68-1463-50
Rev. A
10 09
Output signal
format from
the receiver
Receiver's DIP
switch settings
C Sync SOG Video
RGBHV
RGBS
RGsB
Component*
S-video*
Composite*
* Input video format must match
Figure 5 – Mounting the Receiver
Receive (Rx)
Transmit (Tx)
Ground ( )
Bidirectional
Mono Audio Output RS-232 Output
Tip
Ring
Sleeve
RxTx
RS-232
Device
Ground ( )
Receive (Rx)
Transmit (Tx)
RxTx
Do not tin the wires!
Figure 4 – DIP Switches
MTP 15HD RSA D Rx Front Panel
OUTPUT
PEAKING
LEVEL
AUDIO RS-232
Tx Rx
4
6
5
7
Wall opening
is flush with
edge of box.
Wall Box
Decora
Faceplate
Extron
MTP R 15HD RSA D
OUTPUT
PEAK
LEVEL
AUDIO RS-232
Tx Rx
Figure 6 – Front Panel Connections
Figure 7 – Audio/RS-232 Wiring