Extron electronics SW USB Pro Series User manual

1
IMPORTANT:
IMPORTANT:
Go to www.extron.com for the complete
user guide, installation instructions, and
specifications before connecting the
product to the power source.
SW USB Pro Series • Setup Guide
The SW USB Pro Series switchers make it possible for two or four host computers to share and switch among up to four
peripheral USB devices, such as USB storage devices, USB cameras, keyboards, and mice. The switchers support USB 3.2,
2.0, and 1.x host and peripheral devices, with data rates up to 10 Gbps. They are compatible with all major computer operating
systems.
The SW USB Pro Series provide control via front panel buttons, USB, Extron Product Control Software (PCS), Ethernet, RS‑232,
and auto‑switching for integration with any control system. Front panel LED indicators provide immediate visual conrmation of
signal presence for each input and output.
MODEL80
FLATPA NEL
SW2 USB PRO
POWER
--A MAX
12V
HOSTSDEVICESREMOTE
SS 10GSS 10GUSB HID
2
900 mA
100 mA
USB-C
1
1.5A
USB-C
1
USB-C
23
4
RS-232
Tx Rx G
R
LAN
USBCHARGER
POWER STANDBY
Extron
Cable Cubby 100
Cable Access Enclosure
Extron
SW2 USB Pro
SuperSpeed
USB Switcher
PC
Mouse
USB Mic
USB
Camera
La
ptop
HDMI
HDMI
USB
USB
USBUSB
USBUSB
Display
Keyboard
Figure 1. Application Diagram
This guide provides instructions for an experienced installer to set up and operate these switchers. For full installation,
conguration, and operation details, see the SW USB Pro Series User Guide, available at www.extron.com.
1

2
SW USB Pro Series • Setup Guide (Continued)
Rear Panel Features and Connections
AAA
SW2 USB PRO
POWER
1.6A MAX
12V
HOSTS DEVICESREMOTE
SS 10G SS 10G USB HID
2
900 mA
100 mA
USB-C
1
1.5A
USB-C
1
USB-C
23
4
RS-232
Tx Rx G
R
LAN
DDD
BBBEEEFFFGGGHHHIII
Figure 2. Rear Panel — SW2 USB Pro
SW4 USB PRO
POWER
1.6A MAX
12V
HOSTSDEVICESREMOTE
SS 10G SS 10G USB HID
2
900 mA
100 mA
USB-C
1
1.5A
USB-C
1
USB-C
23
4
RS-232
Tx Rx G
R
LAN
34
AAADDD
BBBEEEFFFGGGHHHIII
CCC
Figure 3. Rear Panel — SW4 USB Pro
A 2-pole DC Power connector F Outputs 3 and 4 — USB Type A connectors
for USB 2.0 and 1.x
B USB-C host connectors
C USB Type B host connectors (SW4 USB Pro only) GRemote RS-232 port
D Device 1 — USB-C connector for USB 3.2, 2.0, and 1.xHLAN (Ethernet) connector
E Device 2 — USB Type A connector for USB 3.2, 2.0, and 1.xIReset (R) button and LED
Installation Steps
1. (Optional) Mount the switcher to a rack shelf or furniture.
2. Connect host PCs to the SW USB Pro USB‑C input connectors (see gure 2 or 3, B). The USB‑C host connectors do not
provide power to the connected host PCs.
3. Connect one or more peripheral USB devices (for example, keyboards, mice, or USB cameras) to the SW USB Pro output
device ports (Dthrough F).
If host emulation will be used, attach a standard keyboard or mouse to USB host port 3 or 4 (C). If host emulation is not
used, connect devices to any desired port.
4. (Optional) Connect an RS‑232 cable between the SW USB Pro RS‑232 port (G) and a host computer or control system, or
connect the SW USB Pro Ethernet port (H) to the network via a standard Ethernet cable (see the SW USB Pro Series User
Guide, available at www.extron.com).
Default LAN settings:
• Rear panel LAN IP address — 192.168.254.254
• Front Panel USB-C port IP address — 203.0.113.22 at port 22023
• Subnet mask: 255.255.255.0
• Gateway: 0.0.0.0
• DNS: 0.0.0.0
• Username: admin
• Password: The product unit serial number. If an absolute system reset is performed, all passwords on this device are
reset to extron.
NOTES:
• The computer used for RS‑232 control should not be one of the host devices connected to any of the input ports.
• The LAN IP address can be changed, however, the USB‑C port IP address is fixed at 203.0.113.22 and cannot be
changed.
2
3

3
5. Connect the included power supply to the switcher power connector (see figures 2 and 4, A).
6. (Optional) Congure the switcher using PCS as necessary for functions such as autoswitching, front panel lock mode, and
emulation (see the SW USB Pro Help File within PCS, available at www.extron.com).
7. Power on the host devices. The switcher is now ready for operation.
Front Panel Features
SW2 USB PRO
USB SWITCHER
EXEC
MODE
AUTO
SWITCH
CONFIG
INPUTS
1 2
STATUS
HOSTS
DEVICES
1234
A
A
AB
B
BC
C
CD
D
DE
E
E
F
F
F
Figure 4. Front Panel — SW2 USB Pro
SW4 USB PRO
USB SWITCHER
EXEC
MODE
AUTO
SWITCH
CONFIG
INPUTS
1
STATUS
HOSTS
DEVICES
1234
2 3 4
A
A
AB
B
BC
C
CD
D
D
E
E
E
F
F
F
Figure 5. Front Panel — SW4 USB Pro
A Exec Mode LED D Input selection buttons and LEDs
B Auto Switch LED E Host LEDs
C USB Config port F Device LEDs
A Exec Mode LED — Lights when front panel lock mode has been enabled. This can be configured via PCS or SIS
commands.
B Auto Switch LED — Lights when auto‑switching is enabled. This can be configured via PCS or SIS commands.
C USB Config port — Connect a USB cable (USB Type A to USB‑C) between a computer or control system and this female
USB‑C port to configure the switcher via SIS commands or PCS, and to update the firmware. This USB‑C port uses IP over
USB communication. The port IP address is 203.0.113.22 at port 22023.
D Input selection buttons and LEDs — Press one of these buttons to select an input to switch to the output. The LED at the
right of each button lights when the corresponding input is selected.
If auto‑switching is in effect, these input selection buttons are disabled, but the LEDs continue to light to indicate the
selected input. The input buttons are also used to initiate a system reset and to enable and disable front panel lockout (see
the SW USB Pro Series User Guide for more information).
EHost status LEDs — Light if a host is connected to the corresponding host port, whether or not the input is currently
selected.
FDevice status LEDs — Light when a peripheral device is connected to the corresponding device port and has been
enabled by the selected host.
4
5

4
SW USB Pro Series • Setup Guide (Continued)
68-3537-50 Rev. A
12 21
For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the
Extron Safety and Regulatory Compliance Guide on the Extron website.
© 2021 Extron — All rights reserved. www.extron.com
All trademarks mentioned are the property of their respective owners.
Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876