Extron electronics TLP 700MV User manual

TLP 700MV • Setup Guide
Overview
The Extron TLP 700MV is a wall-mounted TouchLink®Panel that provides simple and versatile conguration and control for a range of
IPLink®control systems.
Graphic and text objects are displayed on the screen. These objects have system control functions associated with them and the
touch overlay allows you to activate or regulate those functions.
The TLP 700MV communicates with the congurable IP Link controller through an Ethernet connection to an IPLinkdevice. Two BNC
connectors allow the screen to be used to preview composite video or S-video.
NOTE: The RJ-45 output on the rear panel of the TLP 700MV must be connected to a network switch, hub, or router that is
connected to an Ethernet LAN or the Internet. An Extron IP Link controller must also be connected to the same network.
Suggested models include IPL T S series (for example, IPL T S4), IPL 250, IPL T CR 48, or IPL T SFI 244.
This guide provides basic instructions for experienced installers to mount and perform initial conguration on the TLP 700MV. Full
instructions and reference material can be found in the TLP 700MV and TLP 700TV User Guide, which is available on the Extron
website (www.extron.com).
TLP 700MV Front Panel Features
LIGHTS
ON
DISPLAY
MUTE
AUDIO
MUTE
SPEECH
MUTE
AUTO
IMAGE
FREEZE
LIGHTS
OFF
SCREEN
SCREEN
HELP
?
4
4
4
5
5
5
6
6
6
1
1
1
2
2
2
3
3
3
LIGHTS
ON
DISPLAY
MUTE
AUDIO
MUTE
SPEECH
MUTE
AUTO
IMAGE
FREEZE
LIGHTS
OFF
SCREEN
SCREEN
HELP
?7
7
7
8
8
8
9
9
9
¢
¢
¢
Figure 1. TLP 700MV Front Panel (left) and Front Panel with Bezel Removed to Show Recessed Buttons (right).
1Buttons — These ten backlit push-buttons (ve on either side of the screen) can be congured, using the Extron Global
Congurator software, to control commonly used functions.
2Motion detector — This detector is capped with a small Fresnel lens that focuses light onto the sensor. When no motion has
been detected for a user-dened period of time, the unit goes into sleep mode. When motion is detected in the vicinity of the
panel, the screen display is restored and all buttons are active.
3Encoder knob — This knob is used for volume control.
4Light sensor — This sensor monitors the level of ambient light and adjusts the screen brightness and button backlighting.
5LCD screen — This 800x480 resolution LCD screen has a touch overlay. The Extron GUI Congurator software is used to
design a graphic user interface, which displays buttons, text, or icons on the screen. The Extron Global Congurator software is
used to program these screen objects to perform user-dened functions.
6Speaker — A single 2 W speaker provides audible feedback for the user.
7Reboot button — This button is recessed behind the bezel. It shuts down and restarts the unit without changing any of the
parameters.
8Reset button — This button is recessed behind the bezel and is used to select from the four different reset modes that are
available with TouchLink panels (see Reset Modes on page 3).
9Menu button — This button is recessed behind the bezel. It activates the on-screen menus for setting up the panel and
calibrating the unit.
¢Reset LED — This LED is recessed behind the bezel. It is visible only when the faceplate has been removed. It lights as an
indicator for the Reset modes.
1
Product Category
IMPORTANT:
Go to for the
complete user guide and installation
instructions before connecting the
product to the power source.
www.extron.com

Mounting the TLP 700MV
A variety of mounting kits are available for the TLP 700MV (see www.extron.com for a complete list). These kits must be purchased
separately. The touchpanel must be mounted by following the instructions provided with the mounting kit.
To mount the TLP 700MV in the wall, follow these instructions and see the gure below. The steps can be easily adapted if the unit is
mounted in furniture (such as a podium or table).
1. Remove the TLP 700MV from its packaging and determine the best location for installation.
2. Remove the bezel from the TLP 700MV.
3. Download the TLP 305MV template from www.extron.com. Print at 100% (do not scale).
4. Use the template to mark the wall or furniture and cut a hole.
5. Ensure all the locking arms are ush with the top and bottom surfaces of the unit.
6. Insert the trim ring and the TLP 700MV to test the hole is the correct size. If necessary, use a rasp or a coarse le to enlarge the
hole.
7. Run the network cable, two BNC video cables, and power supply cables inside the wall of the hole, leaving enough slack in the
cables to connect them to the back of the TLP 700MV. Use the provided power supply for correct operation.
ATTENTION:
• Do not connect any external power supplies until you have read the Attention notications in the Power Supply section
of the TLP 700MV and TLP 700TV User Guide.
• Ne branchez pas de sources d’alimentation externes avant d’avoir lu les mises en garde dans la section
«PowerSupply» du TLP 700MV and TLP 700TV User Guide.
8. Secure the TR700M trim ring (recommended by Extron) to the wall using four screws (see the gure below).
9. Plug the cables into the rear panel connectors.
10. Push excess cables into the wall cavity and t the TLP 700MV into the hole.
11. Use a Phillips head screwdriver to tighten the screws. As the screws tighten, the locking arms rotate into position behind the wall
and hold the unit in place.
ATTENTION:
• Do not overtighten the screws as this can damage the catches or the wall.
• Ne serrez pas trop les vis au risque d’endommager les attaches ou le mur.
Bezel snaps to unit
(4 places on each side).
Tighten screws to
rotate locking arms.
Tr im Ring (recommended)
secured to the wall
with screws (4).
Figure 2. Mounting the TLP 700MV in the Wall
12. Do not replace the bezel at this time because you will need access to recessed Menu and Reset buttons to congure the unit.
Figure 2
2
TLP 700MV • Setup Guide (Continued)

Configuring the TLP 700MV (Initial Setup)
Before using the TLP 700MV, it is essential to congure it using the on-screen menus. There are ve different screens (Main, Volume,
Time, Network, and Video) that can be selected by pressing the appropriate button at the left side of the screen. There is also an Exit
button at the bottom left corner of the screen for leaving the menus.
Setup Menu
Press the recessed Menu button to activate the top-level menu screen. The
menu opens at the Main Setup Page.
Touch an area of the screen to bring it into focus and use the Up and Down
buttons or the volume control knob to adjust the value. Some options
have a single button and toggle between Off and On when the button is
pressed.
Use the different menu pages to adjust the following options. For
more details, see the TLP 700MV and TLP 700TV User Guide at
www.extron.com.
Main (see gure 3) — Adjusts the Sleep timer, Backlight, Auto
Backlight, LED Backlight, and Wake on Motion functions.
Volume — Adjusts the Master, Click, Sounds, and Line In volume
settings.
Time — Sets the correct time and date.
Network — Sets the IP address and the subnet mask, and enables or
disables Dynamic Host Conguration Protocol.
Video — Provides a small video preview window and the controls to set up
the video contrast, color, brightness, and tint.
Figure 3. Setup Menu
Calibration Menu
While in the Setup menu, press the Menu button a second time to open
the calibration-screen. When all four points have been calibrated, the
screen reopens to the Setup screen.
Press Exit to close the on-screen menus.
Reattach the faceplate (see Figure 2 on page 2).
Figure 4. Calibration Screen
Reset Modes
The TLP 700 MV has four reset modes that can be initiated by pressing the Reset button.
NOTE: See the TLP 700MV and TLP 700TV User Guide at www.extron.com for additional details.
• Factory Firmware Mode — Hold the Reset button while applying power to reset the unit back to the base rmware shipped
with the unit.
• Run/Stop Events Mode — Hold the Reset button until the reset LED blinks once (3 seconds), then release and press Reset
momentarily (less than 1 second) within 1 second.
This mode turns events on or off.
• Reset All IP Settings Mode — Hold the Reset button until the reset LED blinks twice (6 seconds), then release and press
Reset momentarily (less than 1 second) within 1 second.
This mode resets the IP address, subnet, gateway, port mapping, and DHCP settings back to factory defaults. The reset LED
blinks 4 times in quick succession, conrming the reset and turning events off. If necessary, reset the IP address, using ARP and
the MAC address.
• Reset Factory Defaults Mode — Hold the Reset button until the reset LED blinks 3 times (9 seconds), then release and press
Reset momentarily (less than 1 second) within 1 second.
This mode causes a reset to factory defaults for everything except rmware.
NOTES:
• The factory congured passwords for all accounts on this device have been set to the device serial number. Passwords
are case sensitive.
• If the device is reset to default settings, the password will be the default password conguration. The default password
is extron.
3
Product Category

TLP 700MV • Setup Guide (Continued)
Software
NOTES:
• To congure the TLP 700MV, use GUI Congurator and Global Congurator 3. This touchpanel is not compatible with GUI
Designer or Global Congurator Plus and Professional.
• These software programs can be downloaded from the Extron website (www.extron.com). For information about
downloading software see the TLP 700MV and TLP 700TV User Guide.
• See the GUI Configurator Help File or the Global Configurator 3 Help File for information about using these programs.
Figure 5. GUI Configurator
Figure 6. Global Configurator 3
Configuring the TLP 700MV Interface
with Global Configurator 3
Install the Global Congurator3 software on a PC and
use it to assign functions to the screen elements that
were created with GUI Congurator.
Open the program by clicking on the desktop icon or
by using Windows Explorer to navigate to the correct
le on your computer. When the program opens (see
the opening screen in gure 6), follow the on-screen
instructions to congure the IP address of the units.
Open the project created with GUI Congurator3 and
assign functions to the buttons and screen graphics and
text.
When the functions have been assigned to all screen
objects, build the project and upload it to the IP Link
controller. For complete information, consult the user
guide for the controller.
Designing the TLP 700MV Interface with
GUI Configurator
Install the GUI Congurator software on a PC and
use it to design the interface that will appear on the
TLP700MV screen.
Open the program by clicking on the desktop icon
or by using Windows® Explorer to navigate to the
correct le on your computer. When the program
opens (see the opening screen in gure 5), you have
an option of opening an existing project, opening an
existing template, or starting a new project to design a
completely new interface.
468-1378-50 Rev. C
01 20
For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the
Extron Safety and Regulatory Compliance Guide on the Extron website.
For information about replacing and disposing of batteries, see the TLP 700MV and TLP 700TV User Guide at www.extron.com.
© 2008 - 2020 Extron Electronics — All rights reserved. www.extron.com
All trademarks mentioned are the property of their respective owners.
Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876