exway Flex User manual

electric skateboard
Manual

① Front of The Board
② Waterproof Grip Tape
(Do not ride in the rain
when it' s broken)
③ Rear of The Board
④ Truck
⑤ Charge Port
⑥ Power Button
⑦ Battery
⑧ ESC
⑨ Motor
⑩ Rear Drive Wheel
Max. Speed：
Max. Climbing Grade：
Range：
Gross Weight：
Torque：
Maximum Power:
Rated Motor Power：
MAX Input Current：
Input Voltage：
Battery Capacity：
Charging Time：
Truck：
Braking Mode：
Applicable Age Range：
Maximum Load：
Water Proof Level：
25mph / 40kph
30% / 16.8°
20Miles / 32km
Riot/Hub 17lbs（7.7kg）
Riot 5.2Nm×2 / Hub 4.6Nm×2
Riot 1700W×2 / Hub 1500W×2
Riot 750W×2 / Hub 600W×2
2A
100-240VAC,50 / 60Hz
259Wh
4.5h ( Standard Charger)
Exway Trist 45°- 8”
Regenerative Braking
16 ~ 50 Years old
120kg / 440lbs
IP55
（Actual data varies depending on rider weight and
riding conditions.）
③
①
②
⑤
⑥
⑧
⑨
⑩
④
⑦
Riot Hub
01

SAFETY WARNING：
1. When the skateboard battery has 5% left, the power output will be cut off to better protect the battery.
(In free mode, both the power output and brakes will be restricted)
2. Connect the magnetic port on the charger to the power button on the board before plugging into the wall outlet.
(Only use an origina l Exway X1 pro charger)
SPECIAL NOTES：
1. The Exway board can be fully charged in about 4 hours 30 minutes. When fully charged the battery charger
indicator light is green.
2. Please refer to the Exway APP or the official website for the latest version of the product manual.
Operation & The state of the indicator lights:
02
Battery Level
with the power off, short press
power Button, light will flash to
indicate battery level.
(1 bar = 25% battery capacity)
Turn On The Board
long press power button for
2 seconds.
Turn Off The Board
With the power on, long press
PowerButton for 3 seconds.
Pairing Mode
With the power off, long press power
Button for 8 seconds.
(light will flash in an anticlockwise
direction)
Brick Recovery/Firmware
Upgrade Mode
With the power off, short press Power
Button for around 7 times.
(light will flash in a clockwise direction)
Charging
light Flashes Continuously.

Screen OLED 0.9 inch:
:2.4GHzWireless Solution
:5V 1AInput Voltage
How to operate the remote:
Accelerate/Brake
Roll the remote wheel forward to accelerate and roll the remote wheel back
Wirelessly Switch Off The Board (Standby Mode)
long press Button A for 3 seconds
Switch Gears
Short Press Button A
Switch Directions
short press button A for 3 times to switch directions
Accelerating
(Roll the remote wheel forward)
Roller
Braking
(Roll the remote wheel backward)
Multifunctional Button A
OLED Screen
03

Setting-Calibration
Remote Control Alert Instructions:
Push the roller forward to the
bottom withot letting go, press A
button to Confirm.
Enter lnto Pairing Mode
Completely turn off the board and then long press the board′s power
button for 8 seconds.
Enter lnto Setting Mode
Long press the remote′s button A for 5 seconds.
Choose the first option “RE-PAIR”
Choose the corrsponding Exway board and
then “YES”
Calibrate the neutral position,
release the roller to make it frss,
press A button to confirm.
Press A button to confirm when
calibration is complete and the
calibration interface is
automatically exited.
04

Remote Control Alert Instructions
ESC OVERHEAT (100℃）
ESC temperature is too high
ESC OVERHEAT
MOTOR OVERHEAT (100℃）
Motor temperature is too high
MOTOR OVERHEAT
ESC OVERHEAT (120℃）
ESC temperature is too high (Danger risk ! Cool it down
before use)
ESC OVERHEAT
MOTOR OVERHEAT (120℃）
Motor temperature is too high (Danger risk ! Cool it down
before use)
MOTOR OVERHEAT
LOW TEMPERATURE
Temperatures below 0 ℃ (be cautious of slippery road conditions)
BATTRY OVERHEAT(55℃）
TBattery temperature is too high
BATTRY(55°)
MOTOR BREAKOOWN
Motor Seizing
MOTOR BREAKDOWN
05

HIGH VOLTAGE(51V)
Voltage is too high
HIGH VOLTAGE(51V)
HIGH VOLTAGE(51.8V)
Voltage is too high (Danger risk ! Discharge it Before use)
HIGH VOLTAGE(51.8V)
LOW TEMPERATURE
Low Charge temperature
LOW TEMPERATURE
DISCONNECTED
The remote is disconnected from the Board
DISCONNECTED
LOW TEMPERATURE
High Charge Temperature
BEATTRY OVERHEAT
Battery or BMS Error
Please check battery communications port
BMS ERROR
06

Flex Hub Part List
⑤ ⑥
①
⑦
④② ③ ④ Remote Cable
② Remote
③ Charger
① Exway Flex Hub
⑥ Manual
⑤ T Skate Tool
⑦ 2.5mm Allen Wrench
④ Remote Cable
② Remote
③ Charger
① Exway Flex Hub
⑥ Manual
⑤ T Skate Tool
⑦ 2.5mm Allen Wrench
⑧ 2.0mm Allen Wrench
Flex Riot Part List
② ③ ④
⑤ ⑧
⑥ ⑦
①

1. Please read and understand the user manual before riding your electric skateboard.
You are responsible for the operation and control of the electric skateboard and you must
know how to control it before you ride.
2. Riding an Exway electric skateboard is extremely dangerous. Whenever you ride your
Exway board you risk great bodily injury, disability, or death from loss of control, collision,
or falls.
3. The Exway electric skateboard can lose connection with the remote control. If this happens
the skateboard becomes a non motorized longboard.
Please always ride within your ability to control the board in case power loss occurs.
Prepare to lose your ability to brake at any time.
4. Skate only in an open area free from vehicles and pedestrian traffic, and other physical
obstacles. You are responsible for learning the basic features of the board such as braking,
accelerating, and switching gears. Always wear a helmet and full protective gear while riding.
5. Do not ride on slippery or uneven surfaces. Only ride in areas with good visibility.
Avoid riding in close proximity to vehicle and pedestrian traffic.
6. The Exway electric skateboard is not a toy and is not intended for children under 16.
7. Please refer to the Exway APP or the official website for the latest version of the
product manual.
8. Do not store board at 100% battery charge for extended periods of time, doing so will
permanently damage the battery. Maintain around 60% charge when storing for a long
time and do not allow battery charge to go below 40%.
Security Warning & Disclaimer:

09
iOS Android
Scan the QR code to download the APP to get the ·electronic version of the manual
扫描二维码下载APP获得电子版说明书
掃描二維碼下載APP獲得電子版說明書
QRコードをスキャンしてAPPをダウンロードし、電子版のマニュアルを取得します
QR 코드를 스캔하여 전자 버전의 설명서를 받으려면 APP를 다운로드하십시오.
Scannen Sie den QR-Code, um die APP herunterzuladen und die elektronische Version des
Handbuchs zu erhalten.
Scannez le code QR pour télécharger l'application pour obtenir la version électronique du
manuel.
·
·
·
·
·
·
·

FCCCaution
Thisdevice complieswithpart15 oftheFCCRules. Operation issubjecttothe
followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)
thisdevice mustacceptanyinterferencereceived, including interferencethatmay
causeundesired operation.
AnyChangesormodifications notexpresslyapprovedbythepartyresponsiblefor
compliance could void theuser's authorityto operatetheequipment.
Note: Thisequipmenthasbeentestedand foundtocomplywiththelimitsforaClass
Bdigitaldevice,pursuanttopart15 oftheFCCRules. Theselimitsare designedto
providereasonableprotection againstharmfulinterferenceinaresidentialinstallation.
Thisequipmentgeneratesusesand canradiateradiofrequencyenergyand, ifnot
installedand usedinaccordancewiththeinstructions, maycauseharmfulinterference
toradiocommunications. However,there isno guaranteethatinterference will not
occurinaparticular installation. Ifthisequipmentdoescauseharmfulinterferenceto
radioortelevision reception, whichcanbedeterminedbyturning theequipmentoff
and on, theuser isencouragedtotrytocorrecttheinterferencebyoneormore ofthe
followingmeasures:
-Reorientorrelocatethereceivingantenna.
-Increasetheseparation between theequipmentand receiver.
-Connecttheequipmentintoanoutleton acircuit differentfromthattowhichthe
receiver is connected.
-Consult thedealer oranexperienced radio/TVtechnician forhelp.
Thedevice has been evaluated to meetgeneralRF exposure requirement.Thedevice
can beused in portableexposure condition withoutrestriction.