Factoryfurniture north Manual

Factory Furniture Ltd |The Stableyard |Coleshill |Swindon SN6 7PT |T [phone] |F [phone]
[email protected] |www.factoryfurniture.co.uk
We reserve the right to change specification without notice. © 2016 Factory Furniture Ltd
NORTH picnic table
Operation & Maintenance Manual

Introduction
Design
Design, shop drawings and development by Factory Furniture Ltd
Manufacture
Factory Furniture manufactured components. Products are assembled in Factory workshops, checked and dispatched ready
for installation. Replacement products or components thereof should be ordered direct from Factory Furniture Ltd
Copyright
The design copyright for the product and drawing copyright remains the sole property of Factory Furniture Ltd
General Specifications
NORTH Picnic Table
Metric length 3000mm | width 1480mm | height 735mm
Imperial length 9’ 10” | width 4’ 10½” | height 2’ 5”
Approx Weight 182kg
Fixing Centres 1680mm (5’ 6”) x 500mm (1’ 7½”)
Detailed Material & Finish Specifications
Table & Seat Slats
• Manufactured from FSC®certified tanalised timber.
• Slats are profiled and left untreated as standard.
• Fixed to galvanised mild steel frame.
Frame
• Manufactured from mild steel with a hot dip galvanised finish.
• Upper and lower sections of frame bolted together with timber seat slats in between.
• Anchored to ground using 4 no. zinc-coated M10 x 75mm sleeve anchors per table.
General Maintenance (Recommended Schedule & Guidelines)
Daily/Weekly/Monthly (or as adopted)
Visual checks of timber table slats and frame - check all items for superficial or physical damage.
Three Monthly
Clean all items as detailed below check all fixings are seated correctly; inspect timber for serious damage and splinters.
Six Monthly
Secure all fixings; full clean as detailed below; check that table is firmly secured to the ground
Specific Maintenance Details
FSC Tanalised Timber
Clean with a stiff brush once per year, especially in more exposed locations, in order to prevent a verdigris type build up on
the timber surface. Ideally this should be completed in early spring. During the cleaning stage, all exposed timber surfaces
should be inspected for splits and splinters. Any splinters and graffiti should be removed and the surface sanded with 100
grit sandpaper in order to remove any uneven / sharp edges or surfaces.
Galvanised Surfaces
For general cleaning using a damp cloth and warm soapy water only. Scourers and abrasive cleaners are NOT suitable for
this type of finish and may damage it. Before using any cleaning agents to remove graffiti etc. try on a small, inconspicuous
area first to avoid causing more unsightly damage.
2NORTH PICNIC TABLE specification
)6&&
5HVSRQVLEOH
)RUHVW0DQDJHPHQW

Repairs
FSC Tanalised Timber
For light damage, please see section on specific maintenance details above. For instances of heavy damage, the timber item
should be replaced. Please order against the part number reference in the reordering section towards the end of this manual.
Galvanised Surfaces
For light damage to hot dipped galvanised finishes repair using a high performance cold galvanising zinc spray (70% zinc or
above). Spray application should be carried out in accordance with approved methods detailed by the product manufacturer.
Please note that it is advisable to use professional painters to achieve best results when touching up larger areas.
Heavy Damage
In the event of serious damage to any component, replacements should be ordered from Factory Furniture Ltd. In this event
(or if the product needs to be disassembled for any reason), please contact Factory Furniture for detailed technical advice.
Reordering / Spares
Part No. Item Description
P2008 / 01 1 no. North picnic table top slat set (4 slats)
P2008 / 02 1 no. North picnic table seat slat set (2 slats)
Instructions For Reordering
If possible, please specify job name or number at the time of reordering to enable identification of details such as the original
species of timber used, stainless steel finishes and polyester powder coat colours etc. In any event where either, additional
orders are required, or spares and replacements are required please contact Factory Furniture Ltd. Using the part numbers
given above as reference should help us to process your enquiry more efficiently.
Note - All fittings required to assemble ordered parts will automatically be included in the order.
AutoCAD Drawing List
FF2008 / 01 NORTH PICNIC TABLE GENERAL ARRANGEMENT DRAWING
FF2008 / 02 NORTH PICNIC TABLE X-SECTION DRAWINGS
FF2008 / 03 NORTH PICNIC TABLE TIMBER PARTS DETAIL DRAWINGS
FF2008 / 04 NORTH PICNIC TABLE STEEL PARTS DETAIL DRAWINGS
FF2008 / 05 NORTH PICNIC TABLE SETTING OUT DRAWING
Contacts
Factory Furniture Ltd,
The Stableyard,
Coleshill,
Swindon.
Wiltshire SN6 7PT
U.K.
Tel [phone]
Fax [phone]
Email [email protected]
Web www.factoryfurniture.co.uk
3NORTH PICNIC TABLE repairs

           
   
       
 

  
   
 

 
 
   


      


 


    

 

     
  

 



  
     

  
!    !    "    
      
    #
   $

 
   

 



  
%
& ' ' ' ( ) * '
( ) ' '
+
,
-
.
,
-
/' ' 0 1 2 3 4 5( 6 * ' 0 1 2 3 4 5
7 8 9 : ; < 2 = 8 : > & ' ' ? & ' ' ? @ ' ' A A
1 B ' C 8 : C 3 D 2 D E F 8 C G 0 3 D C 8 A A D : ; D ; 5
77H
Installation Instructions
ALL INSTALLATION WORKS TO BE CARRIED OUT BY COMPETENT PERSONNEL - INSTALL AS
COMPLETE UNIT.
Table - Surface fix
North Picnic Table
1. Install suitable foundation pads (see illustration) each with top face at ground level.
2. Position table in correct orientation with bases centrally on foundation pads; mark hole positions through frame.
3. Remove the table; drill holes Ø12mm x 75mm deep (or as bolt manufacturer’s recommendations).
4. Clear debris from holes.
5. Reposition table and fix to foundation pads using 4 no. zinc-coated M10 x 75mm sleeve anchors tightened to 50Nm (or as
per manufacturer’s instruction). Ensure table remains level during fixing process.
4NORTH PICNIC TABLE installation