Factoryfurniture Quay Cycle Stands Manual

factoryfurniture.co.uk
Quay Cycle Stands
OPERATION & MAINTENANCE MANUAL

factoryfurniture.co.uk
Introduction
Design
Design, shop drawings and development by
Factory Furniture Ltd.
Manufacture
Factory Furniture manufactured components. Products
are assembled in Factory workshops, checked and
dispatched ready for installation. Replacement products
or components thereof should be ordered direct from
Factory Furniture Ltd.
Copyright
The design copyright for the product and drawing
copyright remains the sole property of Factory Furniture
Ltd.
General Specifications
QUAY Cycle Stand A
Metric L 335mm | W 80mm | H 725mm *
Imperial length 1’ 1” | width 3” | height 2’ 4½” *
* Not incl. +200mm (8“) below ground level for sub-surface fix
Approx Weight 13kg
QUAY Cycle Stand B
Metric L 480mm | W 80mm | H 725mm *
Imperial length 1’ 7” | width 3” | height 2’ 4½” *
* Not incl. +200mm (8“) below ground level for sub-surface fix
Approx Weight 14kg
QUAY Bollard
Metric L 140mm | W 100mm | H 740mm *
Imperial length 5½” | width 4” | height 2’ 5” *
* Not including +200mm (8”) below ground level for sub-surface fix
Approx Weight 16kg
Detailed Material & Finish
Specifications
Timber Slat(s)
• Manufactured from FSC® certified timber.
• Slats are profiled and left untreated as standard.
• Fixed to galvanised mild steel frame.
Frame
• Manufactured from mild steel with a hot dip
galvanised finish. (Option for polyester powder
coated finish available on request (any RAL colour).
• Root fixed 200mm (8”) below ground level
General Maintenance
(Recommended Schedule & Guidelines)
Daily/Weekly/Monthly (or as adopted)
Visual checks of timber slat(s) and frame - check all
items for superficial or physical damage.
Three Monthly
Clean all items as detailed below check all fixings are
seated correctly; inspect timber for serious damage and
splinters.
Six Monthly
Secure all fixings; full clean as detailed below; check
that product is firmly secured to the ground
Specific Maintenance Details
FSC Timber
Clean with a sti brush once per year, especially in more
exposed locations, in order to prevent a verdigris type
build up on the timber surface. Ideally this should be
completed in early spring. During the cleaning stage,
all exposed timber surfaces should be inspected for
splits and splinters. Any splinters and grati should
be removed and the surface sanded with 100 grit
sandpaper in order to remove any uneven / sharp edges
or surfaces.
Galvanised & Polyester Powder Coated Surfaces
For general cleaning using a damp cloth and warm
soapy water only. Scourers and abrasive cleaners are
NOT suitable for this type of finish and may damage it.
Before using any cleaning agents to remove grati etc.
try on a small, inconspicuous area first to avoid causing
more unsightly damage.
Repairs
FSC Timber
For light damage, please see section on specific
maintenance details above. For instances of heavy
damage, the timber item should be replaced. Please
order against the part number reference in the
reordering section towards the end of this manual.
Galvanised Surfaces
For light damage to hot dipped galvanised finishes
C005669
Responsible
Forest Management

factoryfurniture.co.uk
repair using a high performance cold galvanising zinc
spray (70% zinc or above). Spray application should
be carried out in accordance with approved methods
detailed by the product manufacturer. Please note that
it is advisable to use professional painters to achieve
best results when touching up larger areas.
Polyester Powder Coated Surfaces
For light damage (scratches, chips etc.) repair using
touch-up paint to match original colour (available
from Factory Furniture Ltd). Paint application should
be carried out in accordance with approved methods
detailed by the paint manufacturer. Please note that
it is advisable to use professional painters to achieve
best results when touching up larger areas. Products
for respraying larger areas are available from Factory
Furniture Ltd.
Heavy Damage
In the event of serious damage to any component,
replacements should be ordered from Factory Furniture
Ltd. In this event (or if the product needs to be
disassembled for any reason), please contact Factory
Furniture for detailed technical advice.

factoryfurniture.co.uk
Installation Instructions
All installation works to be carried out by competent
personnel - install as complete unit.
Bike Stands / Bollard
(sub-surface fix only)
1. Install suitable foundation pad (see illustration) with
top face at ground level
2. As soon as possible after pouring concrete for pad,
position bike stand / bollard in correct orientation
centrally in foundation pad. Maintain bike stand /
bollard at correct height (200mm below ground)
and vertical whilst concrete sets (at least 24 hours).
Cycle Stand B
Gnd
Lvl
Gnd
Lvl
8048080335
Foundation
1 no. pad
500x300x400mm in
C20 concrete
(recommendation only)
Foundation
1 no. pad
600x300x400mm in
C20 concrete
(recommendation only)
200 725 200 725
Cycle Stand A
Bollard
Gnd
Lvl
100140
Foundation 1 no. pad
400x400x400mm in
C20 concrete
(recommendation only)
200 740
Bike Stands (Sub-surface Fix Only)
Bollard (Sub-surface Fix Only)
5 Pioneer Road, Faringdon,
Oxfordshire SN7 7BU
[phone]
[email protected].uk