Factoryfurniture SKOP Series Manual

Factory Furniture Ltd |5 Pioneer Road |Faringdon |Oxfordshire SN7 7BU |T [phone]
[e-mail] |www.factoryfurniture.co.uk
We reserve the right to change specification without notice. © 2017 Factory Furniture Ltd
Operation & Maintenance Manual
SKOP bin

Introduction
Design
Design, shop drawings and development by Factory Furniture Ltd.
Manufacture
Factory Furniture manufactured components. Products are assembled in Factory workshops, checked and
dispatched ready for installation. Replacement products or components thereof should be ordered direct from
Factory Furniture Ltd.
Copyright
The design copyright for the product and drawing copyright remains the sole property of Factory Furniture Ltd.
General Specifications
Bin
Metric length 450mm | width 450mm | height 900mm
Imperial length 1’ 5½” | width 1’ 5½” | height 2’ 11½”
Approx Weight 50kg
Liner Capacity 90ltr
Fixing Centres 360mm (1’ 2”) x 250mm (10”)
Detailed Material & Finish Specifications
Bin
• Manufactured from stainless steel with satin polished finish
• Hinged door panel opens to allow access to removable bin liner - secured with standard 8mm tri-drive
slam lock
• Hinges for door manufactured from stainless steel
• Anchored using 4 no. zinc-coated steel M10 x 75mm sleeve anchors per base
Liner
• Liner is removable
• Manufactured from pre-galvanised mild steel sheet
General Maintenance (Recommended Schedule & Guidelines)
Daily/Weekly/Monthly (or as adopted)
Visual checks of bin and liner - check all items for superficial or physical damage.
Three Monthly
Clean all items as detailed below check all fixings are seated correctly.
Six Monthly
Secure all fixings; full clean as detailed below; check that bin is firmly secured to the ground
Specific Maintenance Details
Stainless Steel (polished stainless steel only)
Clean as required, but at least every three months, using a stainless steel polish and a lint free cloth. To remove
ground in dirt, a stainless steel finishing pad may be required.
Galvanised
For general cleaning using a damp cloth and warm soapy water only. Scourers and abrasive cleaners are NOT
suitable for this type of finish and may damage it. Before using any cleaning agents to remove graffiti etc. try
on a small, inconspicuous area first to avoid causing more unsightly damage.
2SKOP BIN specification

Repairs
Stainless Steel
Light damage (surface scratches etc.) can be removed using an emery pad (240 grit) and freeing oil such as
‘WD40’. Care should be taken to follow the direction of the brushing grain. It is recommended that a trial repair
be carried out on an unimportant surface first. No corrosive cleaners or other abrasives should be used. Any
contamination, particularly carbon steel scuffs from vehicles, should be quickly removed to avoid corrosion.
Galvanised Surfaces
For light damage to hot dipped galvanised finishes repair using a high performance cold galvanising zinc spray
(70% zinc or above). Spray application should be carried out in accordance with approved methods detailed by
the product manufacturer. Please note that it is advisable to use professional painters to achieve best results
when touching up larger areas.
Heavy Damage
In the event of serious damage to any component, replacements should be ordered from Factory Furniture Ltd.
In this event (or if the product needs to be disassembled for any reason), please contact Factory Furniture for
detailed technical advice.
Reordering / Spares
Part No. Item Description
P3002 / 01 1 no. Skop bin liner
P3002 / 02 1 no. Skop bin lock & key
P3002 / 03 1 no. Skop bin key
Instructions For Reordering
If possible, please specify job name or number at the time of reordering to enable identification of details such
as the stainless steel finishes and polyester powder coat colours etc. In any event where either, additional
orders are required, or spares and replacements are required please contact Factory Furniture Ltd. Using the
part numbers given above as reference should help us to process your enquiry more efficiently.
Note - All fittings required to assemble ordered parts will automatically be included in the order.
AutoCAD Drawing List
FF3002 / 01 SKOP LITTER BIN OVERVIEW DRAWING
FF3002 / 02 SKOP LITTER BIN LASERCUT & BENT PARTS DETAIL DRAWING (PART 1)
FF3002 / 03 SKOP LITTER BIN LASERCUT & BENT PARTS DETAIL DRAWING (PART 2)
FF3002 / 04 SKOP LITTER BIN VARIOUS PARTS DETAIL DRAWING
FF3002 / 05 SKOP LITTER BIN ASSEMBLY & X-SECTION DRAWINGS
FF3002 / 06 SKOP LITTER BIN BIN LINER FABRICATION DRAWING
FF3002 / 07 SKOP LITTER BIN SET OUT DRAWING
Contacts
Factory Furniture Ltd
5 Pioneer Road
Faringdon, Oxon
SN7 7BU UK
Tel [phone]
Email [e-mail]
Web www.factoryfurniture.co.uk
3SKOP BIN repairs

450
450
360 Ctrs250 Ctrs
900
Ground Level
Foundation -
500x500x400mm
C20 concrete block
(recommended)
400 (Liner)
590 (Liner)
400 (Liner)
85
Ø12
360 (Ctrs)
M10 x 75mm
sleeve anchor
into 12mm hole
in foundation
Ø13mm
clearance hole
in foot base
360 (Ctrs) 7070
500
250 (Ctrs) 125125
500
Installation Instructions
ALL INSTALLATION WORKS TO BE CARRIED OUT BY COMPETENT PERSONNEL - INSTALL AS COMPLETE UNIT
Skop Bin (Surface Fix Only)
Skop Bin (surface fix only)
1. Install suitable foundation pad (see illustration) with top face at ground level
2. Position bin in correct orientation with base centrally on foundation pad, then mark hole positions through
base plates.
3. Remove the bin; drill holes Ø12mm x 85mm deep or as manufacturer’s instructions
4. Clear debris from holes.
5. Reposition bin unit and fix to foundation pads using 4 no. zinc-coated M10 x 75mm sleeve anchors tightened
to 50Nm (or as per manufacturer’s instruction). Ensure bench remains level during fixing process.
IMPORTANT NOTE:
Ensure that stainless steel is protected during site cutting of stone – contamination from disc cutters will
produce corrosion on stainless steel components.
4SKOP BIN installation