Factoryfurniture UTIL table Manual

Factory Furniture Ltd |The Stableyard |Coleshill |Swindon SN6 7PT |T [phone] |F [phone]
[email protected] |www.factoryfurniture.co.uk
We reserve the right to change specification without notice. © 2008 Factory Furniture Ltd
UTIL table
Operation & Maintenance Manual

Introduction
Design
Design, shop drawings and development by Factory Furniture Ltd
Manufacture
Factory Furniture manufactured components. Products are assembled in Factory workshops, checked and dispatched ready
for installation. Replacement products or components thereof should be ordered direct from Factory Furniture Ltd
Copyright
The design copyright for the product and drawing copyright remains the sole property of Factory Furniture Ltd
General Specifications
Table
Metric length 1900mm | width 700mm | height 750mm
Imperial length 6’ 3” | width 2’ 3½” | height 2’ 5½”
Approx Weight 50kg
Fixing Centres 1860mm (6’ 1”) x 570mm (1’ 10½”)
The Util table can be combined with a couple of Util benches to create an outdoor dining set.
Detailed Material & Finish Specifications
Table Slats
• Manufactured from FSC®certified tropical hardwood (other FSC timber options available upon request)
• Profiled and left untreated as standard (oil or microporous woodstain treatment available on request)
• Supported on frame and attached with 8 no. fixing points per slat
Frame
• Manufactured from stainless steel square section tubing with satin polished finish
• Anchored using 4 no. zinc-coated M10 x 75mm sleeve anchors per table (1 no. per leg)
General Maintenance (Recommended Schedule & Guidelines)
Daily/Weekly/Monthly (or as adopted)
Visual checks of table top and frame - check all items for superficial or physical damage.
Three Monthly
Clean all items as detailed below check all fixings are seated correctly; inspect timber for serious damage and splinters.
Six Monthly
Secure all fixings; full clean as detailed below; check that table is firmly secured to the ground
Specific Maintenance Details
FSC Timber
Clean with a stiff brush once per year, especially in more exposed locations, in order to prevent a verdigris type build up on
the timber surface. Ideally this should be completed in early spring. During the cleaning stage, all exposed timber surfaces
should be inspected for splits and splinters. Any splinters and graffiti should be removed and the surface sanded with 100
grit sandpaper in order to remove any uneven / sharp edges or surfaces.
During the first few months after installation the tannin naturally occurring in the timber may leach out and cause a brown
staining on the bases. This may be removed with a light solution of household bleach and water.
Stainless Steel (polished stainless steel only)
Clean as required, but at least every three months, using a stainless steel polish and a lint free cloth. To remove ground in dirt,
a stainless steel finishing pad may be required.
2UTIL TABLE specification
)6&&
5HVSRQVLEOH
)RUHVW0DQDJHPHQW

Repairs
FSC Timber
For light damage, please see section on specific maintenance details above. For instances of heavy damage, the timber item
should be replaced. Please order against the part number reference in the reordering section towards the end of this manual.
Stainless Steel
Light damage (surface scratches etc.) can be removed using an emery pad (240 grit) and freeing oil such as ‘WD40’. Care
should be taken to follow the direction of the brushing grain. It is recommended that a trial repair be carried out on an
unimportant surface first. No corrosive cleaners or other abrasives should be used. Any contamination, particularly carbon
steel scuffs from vehicles, should be quickly removed to avoid corrosion.
Heavy Damage
In the event of serious damage to any component, replacements should be ordered from Factory Furniture Ltd. In this event
(or if the product needs to be disassembled for any reason), please contact Factory Furniture for detailed technical advice.
Reordering / Spares
Part No. Item Description
P2001 / 01 1 no. Util Table slat set (8 slats in total)
Instructions For Reordering
If possible, please specify job name or number at the time of reordering to enable identification of details such as the original
species of timber used, stainless steel finishes and polyester powder coat colours etc. In any event where either, additional
orders are required, or spares and replacements are required please contact Factory Furniture Ltd. Using the part numbers
given above as reference should help us to process your enquiry more efficiently.
Note - All fittings required to assemble ordered parts will automatically be included in the order.
AutoCAD Drawing List
FF2001 / 01 UTIL TABLE FABRICATION DRAWING
FF2001 / 02 UTIL TABLE PARTS DETAILS DRAWING
FF2001 / 03 UTIL TABLE SETTING OUT DRAWING
Contacts
Factory Furniture Ltd,
The Stableyard,
Coleshill,
Swindon.
Wiltshire SN6 7PT
U.K.
Tel [phone]
Fax [phone]
Email [email protected]
Web www.factoryfurniture.co.uk
3UTIL TABLE repairs

       



          
 
                 
                 

 

     

              ! "
#     
$ % & ' ( ) * + % ' , ' % - . ) ( /
0 1 1 2 , 1 1 2 3 1 1 4 4 + '
5 , 1 6 % ' 6 7 8 * 8
9 7 8 6 % 4 4 8 ' ( ) * + % ' % ' : ; <
= > 1 2 ? @ 4 4 / : 8 8 A 8
) ' 6 B % 7 + ' * % > , 4 4 B % : 8
+ ' C % & ' ( ) * + % ' D + * B
) ' * + E A ) ' ( ) : ) 7 4 % & 7 7 + ' F
G
H
> ,
Installation Instructions
ALL INSTALLATION WORKS TO BE CARRIED OUT BY COMPETENT PERSONNEL - INSTALL AS
COMPLETE UNIT.
Util Table (Surface Fix Only)
Util Table (surface fix only)
1. Install suitable foundation pads (see illustration) each with top face at ground level
2. Position table in correct orientation with bases centrally on foundation pads; then mark hole
positions through fixing lugs.
3. Remove the table; drill holes Ø12mm x 75mm deep (or as bolt manufacturer’s
recommendations).
4. Clear debris from holes.
5. Reposition table unit and fix to foundation pads using 4 no. zinc-coated M10 x 75mm sleeve
anchors tightened to 50Nm (or as per manufacturer’s instruction). Ensure table remains level
during fixing process. Finally hammer an anti-vandal armour ring over each bolt head to
prevent tampering.
6. Check level & re-instate ground level if necessary (sub-surface fix).
IMPORTANT NOTE:
Ensure that stainless steel is protected during site cutting of stone – contamination from disc cutters will produce corrosion on
stainless steel components.
4UTIL TABLE installation

                 
             
            
                   
             
                 
              
    !                "
#
$
 
% & ' ( ) * + , & ( - ( & . / * ) 0 - 1 1 1 2 3 1 1 2 4 1 1 5 5
, ( 6 - 1 7 & ( 7 8 9 + 9 : 8 9 7 & 5 5 9 ( ) * + , & ( & ( ; < =
>
?
@
A
?
@
B ( )
; 9 C 9 ;
4 3 1
D E F G H I J K L M N
1
D E F G H I J K L
4 3 1
D E F G H I J K L
O -
M
O -
M
3
N
1
N
1 1 3
N
1
O P 1 1 O Q P 1
O Q R 1 : % , 2 , ( S 6 + 8 0 =
O
N
R 1 : % , 2 , ( S 6 + 8 0 =
O Q 1 1
- 1 1 1
T
@
@
O 3 O 13 1 1 3 1 1
Installation Instructions
ALL INSTALLATION WORKS TO BE CARRIED OUT BY COMPETENT PERSONNEL - INSTALL AS
COMPLETE UNIT.
Setting out dimensions
Util Outdoor Dining Set (surface fix only)
1. Install suitable foundation pads (see illustration) each with top face at ground level
2. Position table and benches in correct orientation with bases centrally on foundation pads;
then mark hole positions through fixing lugs.
3. Remove the table and benches; drill holes Ø12mm x 75mm deep (or as bolt manufacturer’s
recommendations).
4. Clear debris from holes.
5. Reposition table and benches and fix to foundation pads using 4 no. zinc-coated M10 x
75mm sleeve anchors (per unit) tightened to 50Nm (or as per manufacturer’s instruction).
Ensure table and benches remain level during fixing process. Finally hammer an anti-vandal
armour ring over each bolt head to prevent tampering.
6. Check levels.
IMPORTANT NOTE:
Ensure that stainless steel is protected during site cutting of stone – contamination from disc cutters will produce corrosion on
stainless steel components.
5UTIL (Dining Set) installation