Factoryfurniture TORD Manual

Factory Furniture Ltd |The Stableyard |Coleshill |Swindon SN6 7PT |T [phone] |F [phone]
[email protected] |www.factoryfurniture.co.uk
We reserve the right to change specification without notice. © 2013 Factory Furniture Ltd
TORD bench
Operation & Maintenance Manual

Introduction
Design
Design, shop drawings and development by Factory Furniture Ltd
Manufacture
Factory Furniture manufactured components. Products are assembled in Factory workshops, checked and dispatched ready
for installation. Replacement products or components thereof should be ordered direct from Factory Furniture Ltd
Copyright
The design copyright for the product and drawing copyright remains the sole property of Factory Furniture Ltd
General Specifications
Bench
Metric length 2300mm | width 400mm | height 450mm
Imperial length 7’ 6½” | width 1’ 3½“ | height 1’ 5½”
Approx weight 68kg
Fixing centres 1200mm (3’ 11”) x 160mm (6½”)
Detailed Material & Finish Specifications
Bench Slats
• Manufactured from FSC®certified tropical hardwood
• Slats are profiled and left untreated as standard (oil or microporous woodstain treatment available on
request)
• Spacers and end caps in aluminum (stainless steel available on request) fastening 4 no. zinc-coated
mild steel threaded tie rods per bench top
Bench Frames
• Manufactured from hot dipped galvanised mild steel rectangular box section and featuring an all welded construction
General Maintenance (Recommended Schedule & Guidelines)
Daily/Weekly/Monthly (or as adopted)
Visual checks of bench - check all items for superficial or physical damage.
Three Monthly
Clean all items as detailed below check all fixings are seated correctly.
Six Monthly
Secure all fixings; full clean as detailed below; check that bench is firmly secured to the ground
Specific Maintenance Details
FSC Timber
Clean with a stiff brush once per year, especially in more exposed locations, in order to prevent a verdigris type build up on
the timber surface. Ideally this should be completed in early spring. During the cleaning stage, all exposed timber surfaces
should be inspected for splits and splinters. Any splinters and graffiti should be removed and the surface sanded with 100
grit sandpaper in order to remove any uneven / sharp edges or surfaces.
During the first few months after installation the tannin naturally occurring in the timber may leach out and cause a brown
staining on the bases. This may be removed with a light solution of household bleach and water.
Galvanised Surfaces
For general cleaning using a damp cloth and warm soapy water only. Scourers and abrasive cleaners are NOT suitable for
these types of finish and may damage them. Before using any cleaning agents to remove graffiti etc. try on a small,
inconspicuous area first to avoid causing more unsightly damage.
2TORD specification
)6&&
5HVSRQVLEOH
)RUHVW0DQDJHPHQW

Repairs
FSC Timber
For light damage, please see section on specific maintenance details above. For instances of heavy damage, the timber item
should be replaced. Replacements should be ordered from Factory Furniture Ltd
Galvanised Surfaces
For light damage to hot dipped galvanised finishes repair using a high performance cold galvanising zinc spray (70% zinc or
above). Spray application should be carried out in accordance with approved methods detailed by the product manufacturer.
Please note that it is advisable to use professional painters to achieve best results when touching up larger areas.
Heavy Damage
In the event of serious damage to any component, replacements should be ordered from Factory Furniture Ltd. In this event
(or if the product needs to be disassembled for any reason), please contact Factory Furniture for detailed technical advice.
Reordering / Spares
Part No. Item Description
P1036 / 01 1 no. Tord bench slat set and ties (not including bases) - (2 no. outer slats and 3 no. inner slats total)
Instructions For Reordering
If possible, please specify job name or number at the time of reordering to enable identification of details such as the original
species of timber used, stainless steel finishes and polyester powder coat colours etc. In any event where either, additional
orders are required, or spares and replacements are required please contact Factory Furniture Ltd. Using the part numbers
given above as reference should help us to process your enquiry more efficiently.
Note - All fittings required to assemble ordered parts will automatically be included in the order.
AutoCAD Drawing List
FF1036 / 01 TORD BENCH GENERAL ARRANGEMENT DRAWING
FF1036 / 02 TORD BENCH PARTS DETAIL DRAWINGS
Contacts
Factory Furniture Ltd,
The Stableyard,
Coleshill,
Swindon.
Wiltshire SN6 7PT
U.K.
Tel [phone]
Fax [phone]
Email [email protected]
Web www.factoryfurniture.co.uk
3TORD Repairs




               
  
        
         
                 
              
          
                   
    
!
"
#
$ $ % & & ' ( ) *
+ , - . / 0 . 0 - 1 0
/ 2 3 , 1 - - . 4 5 2 6 5 '. 0
5 2 + 1 7 ) 8 & & , 1 9 .
( ) * : ; :
3 / < 2 = +
>
?
8 * * ' 8 * * ' 8 * * & &
@ $ * @ 1 2 3 - . + . A / 4 .
B- . 3 1 & & . 2 0 . 0 C
D- 1 = 2 0 9 . E . 9
7) 8
Installation Instructions
ALL INSTALLATION WORKS TO BE CARRIED OUT BY COMPETENT PERSONNEL - INSTALL AS
COMPLETE UNIT.
Surface Fix
Tord Bench (surface fix only)
1. Install suitable foundation pads (see illustration) each with top face at ground level
2. Position bench in correct orientation with bases centrally on foundation pads, then mark hole positions through base frame.
3. Remove the bench; drill holes Ø14mm x 175mm deep
4. Clear debris from holes.
5. Fill the holes to within approximately 35mm from the top with Hilti HY150 resin (or similar). Lift the bench (with threaded
anchor rods/capnuts in place) and carefully lower the anchors into the holes, leave for two hours before using.
6. Using a torque wrench, tighten nuts and washers over base frame to 30Nm to fasten down the bench.
7. Check level
IMPORTANT NOTE:
Ensure that stainless steel is protected during site cutting of stone – contamination from disc cutters will produce corrosion on
stainless steel components.
4TORD installation