FALCON RIDGE AC-12PROWLER-FC05 Installation manual

2515 Bypass Rd. Flemingsburg, KY 41041
606-845-7439
Instructions for Installation and Care of Arctic Cat Prowler 2012 to Present
Full Cab Fits Poly Windshield
AC-12PROWLER-FC05
Notice: Do not smoke inside the cab or expose the enclosure to direct flames. Cab is Flammable.
Be sure to read these instructions thoroughly before opening and installing the enclosure. The installation is
best done when the temperature is 70 degrees F. or warmer. The temperature affects the adhesive Velcro, if
conditions prevent installing in warmer weather it helps to store the adhesive Velcro at room temperature
prior to installation.
1. Carefully open the carton and remove the enclosure on a large flat surface that is clean and free of dirt.
2. Check over the parts included in the carton with the parts list shown below:
2” Adhesive Velcro Hook Strips: 30 each------------3”
“ “ ““4 each------------6”
“ “ ““4 each------------8”
““ ““2 each------------20”
1” Adhesive Velcro Hook Strips: 2 each------------19”
70” Para Cord 2 each
Webbing Straps with Velcro 4 each
Webbing Straps with Grommet 2 each
Snap Stud with Screw 6 each (1 Extra)
Cab Enclosure 4 panels
If any parts are damaged or missing please contact customer service at [phone].

3. The majority of the door is held in place by double-sided Velcro strips sewn perpendicular to the edges.
You need to wrap the roll cage with one of the 6” adhesive Velcro strips first and then wrap the double-
sided Velcro around the adhesive strip to provide a secure hold. Below are photos showing how these
should look.
4. While locating the positions for the adhesive Velcro the best place to start is the front corner. Place a 6”
adhesive Velcro strip at the bottom of the front roll cage as shown on the next page.

5. Now install the 16” long 1” wide adhesive Velcro strip down the front of the fender as shown below.
6. After the Velcro is placed at the bottom of the roll cage and along the fender line attach the front of the
door to place it where it needs to be. This helps to assure that all the remaining Velcro will be at the
correct locations to hang the door right. The photo on the next page shows how the front of the door
should look.
7. Now move on to wrapping the adhesive Velcro around the roll cage at where each double-sided strip is
sewn to the edge as shown on the first page.

8. To finish off the door attach the 20” adhesive Velcro strip down the rear portion of the door as shown
below. Then attach the door to the Velcro.
9. Once the door is in place install the rear window. The top of the windshield is held in place by two 8”
Velcro tabs sewn along the edges on both sides of the brake light. Attach the adhesive Velcro strips on
the top bar as shown in the photo below.
10. Now take the rear window and attach the two 8” tabs to the adhesive Velcro centering the cutout across
the top under the rear brake light. The photo below shows how it should look.
11. Next attach the four double-sided strips to the roll cage as you did with the door.

12. Also at this point before you lace the Rear Window to the door you should wrap a 6” strip of adhesive
Velcro to the roll cage a little less than halfway up the rear bar. Then wrap the double-sided strip with
the strap sewn to it around the adhesive strip with the webbing strap facing the top of the vehicle. This
will be for holding the Soft Top in place later. The photo below shows how this should look.
13. Now take the two 70” cords and lace the Door Panel to the Rear window as you would a pair of shoes.
Run the cord through the top holes from the inside out so that you have two equal length pieces coming
out of each hole. Then lace the cording down the remaining holes to the bottom and tie them off cutting
off any remaining cord. Be sure to melt the ends to prevent fraying. The photo below show how this
should look.
14. Now time to install the roof panel. Included in your package are two sets of webbing straps. One set
has grommet holes in one end and these are used for the front of the top. The other set has double-sided
Velcro sewn to one end and is used for the rear of the top.