FALCON RIDGE BC-3400-FC05 Installation manual

2515 Bypass Rd. Flemingsburg, KY 41041
606-845-7439
Instructions for Installation and Care of Bobcat 3400 Polaris Ranger
Full Cab Enclosure Fits Lexan
BC-3400-FC05 (NEW STYLE)
Notice: Do not smoke inside the cab or expose the enclosure to direct flames. Cab is Flammable.
Be sure to read these instructions thoroughly before opening and installing the enclosure. The installation is
best done when the temperature is 70 degrees F. or warmer. The temperature affects the adhesive Velcro, if
conditions prevent installing in warmer weather it helps to store the adhesive Velcro at room temperature
prior to installation.
1. Carefully open the carton and remove the enclosure on a large flat surface that is clean and free of dirt.
2. Check over the parts included in the carton with the parts list shown below:
Adhesive Velcro Hook Strips:
Soft Doors
“ “ ““18 each------------3"
“ “““2 each------------38"
Snap Screw Studs 15 each ( 1 extra )
---------------------------------------------------------------------------
Adhesive Velcro Hook Strips: Rear Window
“ “ ““8 each------------3"
“ “ ““1 each------------30"
““““1 each------------55"
---------------------------------------------------------------------------
Top Cap
31” Webbing Straps w/ Grommet 2 each
31” Webbing Straps w/Hook 2 each
45” Webbing Straps w/ Loop 2 each
Adhesive Velcro Hook Strips: 2 each------------6”
The cab for your Ranger is made up of 5 different components that work together to enclose your vehicle.
Install the cab in the following order.
1) Soft Doors
2) Rear Window
3) Poly Windshield
4) Top Cap
If any parts are damaged or missing please contact customer service at [phone].

Soft Doors:
1. Begin by holding the door up to the frame and attach it using the double-sided Velcro strips sewn
perpendicular to the edge of the door. At each of the double-sided strips take one of the 3" adhesive
Velcro strips and adhere it to the inside of the frame. Then wrap the double-sided strip around it so that
the adhesive strip holds it firmly in place. the following diagrams shows how it should look.

2. Next take the 38" adhesive Velcro strips and run it down the back of the roll cage facing towards the
rear of the vehicle. Start at the bottom and work your way up the bar. You will see the double-sided
Velcro tabs sewn along the back of the doors. See photos below.
3. Once all the Velcro is in place the last thing to do is install the screw snap studs. NOTE: The best way
to install the snap studs is to put them in the sockets in the door first. Then push them into the
plastic to make an mark. Then pull the screw stud out and screw it into the plastic where the
mark was made. See Photos Below.

REAR WINDOW:
4. Begin by placing the 30" adhesive Velcro strip centered across the top of the roll cage. Make sure to
place them on top of the bar.
5. Next place the 55” strip across the bottom of the frame. It goes on the metal strip that faces the rear of
the vehicle.
6. Then take the Rear Window and attach it across the bottom first making sure that it is centered properly.
Pull it up and attach the top.
7. Next attach the sides of the Rear Window to the tabs on the back of the doors. See photo below.
POLYCARBONATE WINDSHIELD:
8. Install using the directions included with the windshield.

TOP CAP:
9. After the windshield is installed take the soft Top Cap and put it over the top of the vehicle and make
sure you have the on correctly. When put on correct the sides will match up with the shape of the roll
cage. On the front you will take the shorter straps and wrap the looped end around the roll cage just
below the bottom clamp on the top section of the windshield. Run the other end of the strap through the
loop and pull it tight. Then run the strap up and through the buckle sewn to the corner of the top. The
front strap should look like the photo below.
10. Next take the other two long straps and wrap them around the roll cage in the rear just under door and
rear window at the very bottom of the roll cage. Pull the strap up and connect to the buckle at the rear of
the top.