FALCON RIDGE CF Moto U-Force 1000 Installation manual

2515 Bypass Rd. Flemingsburg, KY 41041
606-845-7439
Instructions for Installation and Care of CF Moto U-Force 1000
Soft Door Rear Window Combo
CF-U-1000-DRW01
Notice: Do not smoke inside the cab or expose the enclosure to direct flames. Cab is Flammable.
Be sure to read these instructions thoroughly before opening and installing the enclosure. The installation is best done
when the temperature is 70 degrees F. or warmer. This is to allow the Velcro to stick to the roll cage better, if you must
install outside in the cold it will help to warm the Velcro inside at room temperature until ready to install.
1. Carefully open the carton and remove the rolled up Cab Enclosure on a large flat surface that is clean and free of
dirt or other material that may soil or scratch the windows of the Cab.
2. Check over the parts included in the carton with the parts list shown below:
1" Adhesive Velcro Strip 2 each 10” long
1 each 54” long
2" Adhesive Velcro Strip
“ “ 1 each 54” long
“ “2 each 29” long
“ “ 2 each 26” long
“ “ 2 each 22” long
“ “ 2 each 18” long
2 each 5" long
Snap studs 24 each ( 2 extra )
Door Panels 2 each
If any parts are damaged or missing please contact customer service at [phone].
3. Begin by cleaning the roll cage and plastic that surrounds the doors. Using rubbing alcohol is preferable. This step
is very important for the Velcro strips to properly adhere.

SOFT DOORS:
4. Now start installation by placing the 2" adhesive Velcro strips around the outside edges of the upper door frame.
Starting at the front of the frame just above the rear view mirror, place the 26" strip as shown in the photo on the
next page.
5. Next place the 29" strip across the top of the frame as shown below.
6. Next place another 18" strip down the rear bar as shown on next page.

7. Next place the 5" strip just below the bracket along the back of the roll cage
8. Last piece of Velcro will be the 10” strip that is 1” wide. This goes on the frame just behind the rear-view mirror as
shown in the photo below.

9. Lastly install the snap studs into the plastic for the bottom portion of the door. It works best to put the screw studs
into the snap sockets on the door first. Then one by one pull the door in place and push the screw into the plastic
making sure to put enough pressure to leave a mark. Then remove the screw stud from the door and install it where
the mark was left behind at. The following pictures show what it looks like.
REAR WINDOW:
1. Begin by cleaning the roll cage that surrounds the rear window. Using rubbing alcohol is preferable. This step is
very important for the Velcro strips to properly adhere.

2. Installing the Rear Window is simple. Take the 1" wide, 54" long adhesive strip and place it across the top of the
Rear Window frame. Then place the two 22" adhesive strips down the sides and then the 2” wide, 54” strip across
the bottom. Once all the Velcro is in place just attach the Rear Window to the frame. The following photos show
how it should look.

Cleaning and Storage Recommendations:
1. Before removing the Cab for storage, make sure it is very clean in order to prevent scratching of the
window panels. Clean with a soft rag or sponge using a mild liquid detergent soap and warm water
solution. Never rub the windows with a dry cloth or rag! Let the Cab dry thoroughly before attempting
to roll for storage.
2. It is important that the Cab be rolled up for storage rather than folding. Folding will cause damage to
the windows!!! Carefully roll up the Cab similar to the way it was when it was packed at the factory.
On a large, clean and flat surface, fold the doors over the rear panel first, then, interleave the top and
windshield on top of the doors. Begin rolling the Cab into a roll approximately 8 inches in diameter.
Put the rolled Cab back into the carton for storage at a normal room temperature. It is best not to expose
the Cab to either extreme hot or cold temperatures when storing.
3. A special cleaner conditioner is available from Falcon Ridge that will greatly increase the service life of
the Cab Enclosure. In addition, if additional hook and loop sets are needed, they can also be ordered.
Thank you for your purchase!

Return Policy
If for any reason you choose to return this product it must be returned within 30 days from date item is
received. You MUST package the product exactly as it was originally packaged from the factory to get a
full refund for the product!
The vinyl windows should never be folded when packaging in the box or for storage purposes. Lay all the
windows on top of each other with the canvas folded in between and the paper (if available) on both sides of the
windows.
All returned products will be inspected upon arrival at the production facility and must be in unused,
factory new condition to receive refund - a 25% restocking fee will apply.
If ordered from Falcon Ridge please call at 606-845-7439 to gain a return authorization number, use our
preferred shipping carrier (UPS) to return the item (unless the item is defective, you are responsible for paying
the shipping to return the item.) Any returns submitted to Falcon Ridge without a return authorization
number will be charged a 20% restocking fee. If ordered from one of Falcon Ridge’s many distributors, you
must first call them and see what their return policy is. Once your item reaches our production facility, our
customer satisfaction team will inspect your item to ensure unused, factory new condition. NOTE: All
windshields must be returned with the original protective film intact and not removed. Do NOT
REMOVE if you have any intentions of returning the item. Refund/ replacement of a windshield will only
be processed on items with original protective film or if the windshield is defective.
Items must be properly packaged in the original shipping carton to protect them during transit and ensure your
returned item arrives back factory fresh, and in new resalable condition (any returned items that have been
used, altered or damaged in any way will not be subject for a refund.) All contents including instruction
manuals, accessories, hardware, Velcro, etc. must be included in your return shipment. Only items in OEM
factory new condition will be approved. Once returned items are received, credit will be issued to the original
credit card/ payment method used for the purchase. Outbound shipping and return shipping cost will not be
refunded. Please allow 4 to 6 weeks for your refund to be processed.
Warranty
To The Owner of this Product:
Thank you for purchasing one of our Falcon Ridge Cab Enclosures, Tops &/or Windshields! Below are the
terms under which your product is covered under our manufacturer’s warranty.
30 Day Warranty which includes and is not limited to replacing the enclosure, tops and/or windshield due to
defect of the product. Please refer to the return policy in this case for more information.
1 Year Warranty includes any defect in material or workmanship within this time frame we will gladly correct
the problem or replace the enclosure, tops &/or windshield. Upon submitting for the correction or replacement
we will need to receive pictures of the defect in material or workmanship along with the receipt from the date of
purchase.