FALCON RIDGE 50-50221KIT User manual

Installation & Operations Manual : FR Flip-Up Windshield, Polaris Mid-Size Pro-Fit Ranger
Part Number 50-50221KIT; 50-50838KIT
1
Installation Information:
This product does not require any modifications to your vehicle. Please familiarize yourself with all the steps before
beginning assembly.
Falcon Ridge was established to help UTV owners adapt their vehicles for the great outdoors, Falcon Ridge
provides innovative, practical, and rugged UTV products to provide owners the confidence to work, play, or explore
in whatever conditions they may encounter.
Were fueled by your passion!
Parts List:
1. 50-50221; 50-50838 MS Ranger Windshield
2. 54-91032 Gasket
3. 54-96047 Tube Assembly
4. 54-96061 Brace Mounting Block Cover
5. 54-96064 T Handle
6. 54-96058 Shim (2)
7. 54-96080 Ball Bracket, Driver
8. 54-96081 Ball Bracket, Pass.
9. 54-96086 Gas Spring (2)
10. 54-96071 Center Retainer
11. 54-96072 Rub Plate
12. 54-96089 Strike Plate, Driver
13. 54-96090 Strike Plate, Pass.
14. 54-96085 Hinge Half, Upper (2)
15. 54-96084 Hinge Half, Lower (2)
16. 54-96055 Ball Stud Clamp (2)
17. 54-96053 MS Ranger Hardware Bag
Tools Needed:
•4mm, 5mm, 6mm Allen Wrenches
•10mm, 12mm, 13mm Open End Wrench
•Socket Wrench with 13mm Socket
•Small Flathead Screwdriver
•T40 Torx Socket
Installation Video
Scan code with your phone’s
camera and follow the link

14
Brace Mounting Block Small Mounting Block End Mounting Block
Parts
2
x 2 x 2 x 2
x 2
x 2
15
1
2
78
6
5
9
10 11 12 13
3
Brace Mounting Block Small Mounting Block End Mounting Block
4
16

In Tube Assembly:
M6x50 Button Head M6x45 Button Head M6x40 Button Head
M8x50 Button Head M8x30 Socket Head M8x16 Button Head
M6x30 Button Head M6x20 Socket Head M6x18 Button Head
M6 Flange Nylon Lock Nut M8 Jam Nut M6 Nylon Lock Nut
M6 Nylon Lock Nut
M8 Nylon Lock Nut M8 Rod End
x 2
x 2 x 2
x 1 x 8
x 3
x 2
x 2
x 2 x 7
x 6 x 2 x 2
x 2
x 12
Hardware
In Hardware Bag:
3

M6x40
M6x45
M6x50
7
Repeat for the other half of windshield so that the
windshield looks like this. Make sure the fasteners are
tight, but you can still rotate the ball brackets by hand
with some resistance.
Take the Tube Assembly out of its box. The tube
should be bowed with the latches curved in towards
you. Using a 4mm Allen wrench, remove all the bolts
and nuts from the mounting blocks except the M6x45
Button Head Bolt in the middle of the Brace Mounting
Block. Use picture above to remember which size bolt
goes with each mounting block.
Place the windshield down on a large flat surface with
something under it to prevent scratching. It should be
oriented with the Gasket bulb-side up. This is the
inside of the windshield. There are two holes about
1.5” apart in the middle of the top of the windshield.
Make sure they are slightly right of center.
Take the Ball Brackets and orient them on the inside
of the windshield as shown. Shown above is Ball
Bracket, Driver. Gather a 4mm allen wrench and a
10mm open wrench. Fasten an M6x18mm Button
Head Bolt through top hole in each ball bracket with a
M6 Flange Nylon Insert Lock Nut on the inside of the
windshield
.
Leave this middle
bolt fastened
1 2
3 4
4
..

Place the Tube assembly on the inside of the
windshield with the pockets for captive nuts in each of
the mounting blocks facing upwards.
Insert two M6x45 Button Head Bolts through the
windshield, and then through the Brace Mounting
Block. Put the outer two M6 Nylon Lock Nuts in their
captive pockets to fasten until just a few threads
engage. At this point just tighten by hand or finger-
tight using a 4mm Allen wrench.
Use a M6x40mm Button Head Bolt and a M6 Nylon
Lock Nut to repeat this process for each Small
Mounting Block. The hole alignment of the mounting
blocks to the holes in the windshield can be adjusted
at any time by rotating the tube within the mounting
blocks.Because of this, it is important to leave all
fasteners loose during steps 6-9.
Check the alignment on the End Mounting Blocks and
rotate the tube if needed. Now gently flex the
windshield towards the tube so that you can insert a
M6x50 Button Head Bolt through the other side of the
windshield, through the bottom hole of the Ball
Bracket, and then through the End Mounting Block.
Use an M6 Nylon Lock Nut in the captive pocket to
fasten the bolt. Only engage about 2-3 threads.
Repeat for other side.
5 6
7 8
5
..

There is a gap for the Shim to be snapped in place
over the M6x50mm Button Head Bolt in between the
End Mounting Block and the Ball Bracket. Insert the
shims in this gap in each side by snapping in from
the bottom side of the windshield. Now, working from
the middle out, tighten all bolts along the tube
assembly except the middle bolt of the Brace
Mounting Block
Remove the two M8 ball studs from each Gas Spring.
There will be 4 total ball studs. Do this by prying up
the metal retaining clip with a small flat blade
screwdriver and pulling the ball stud out. Once the ball
stud has been removed make sure the retaining clip is
back in place.
910
Install one Ball Stud onto each Ball Bracket using an
M8 Nylon Insert Lock Nut. Orient the Ball to face
inwards towards the middle of the windshield, and
fully tighten using 12mm and 13mm open end
wrenches.
11
6
Install the T Handle onto the cylinder with the
M8x30mm Socket Head Bolt. You will need a 6mm
hex key.
12

7
Now install the Center Retainer on the inside of the
windshield using 2 -M6x30 Button Head Bolts and 2 -
M6 Nylon Lock Nuts.
14
Now attach each Hinge Half, Lower to the outer side
of the windshield with the angle coming away from the
polycarbonate. Fasten loosely with 4 –M8x16mm
Button Head Bolts and 4 –M8 Nylon Insert Lock Nuts.
The bolt heads should be on the metal side and the
nuts on the inside of the windshield
15
10
Remove the two bolts holding the buckle on from the
outside. Use two M8x50 Button Head Bolts and two
M8 Nylon Lock Nuts to attach the Strike Plate. Once
in place use a 5mm hex key to tighten the bolt from
the inside and use a 13mm wrench or socket wrench
to fasten the M8 Nylon Lock Nut from the buckle side.
Make sure the Strike Plate stays aligned as shown.
Repeat for the other side.
Shown is the Strike Plate, Passenger Orient the part
as shown.
16
15
15
15

.125”
Thread one M8 Ball Stud into each Ball Stud Clamp
Thread one M8 Jam Nut onto each Rod End until the
nut is 1/8” from the end of the threads
Thread each M8 Rod End into the Hinge Half, Upper
as shown. This is the left upper hinge assembly.
Mirror and repeat for the right side.
17 18
19 20
8
Attach the Ball Stud Clamp to the vehicle frame by
loosening it’s two M8x30 Socket Head Bolts until able
to fit clamp over the tubing. Space the Ball Stud
Clamp from the Strike Plate so that its bottom edge is
12.0 inches away from the top edge of the strike plate.
This will position the ball stud clamps properly for gas
spring installation later. Tighten the M8x30 bolts very
tight!

Use a 5mm hex and a 13mm socket wrench to loosely
fasten two M8x16mm button head bolts and two M8
Nylon Lock Nuts for each Hinge Half, Upper on each
side of the vehicle. Driver side shown
Line up the holes in each side of the top hinges and
insert the M8x50 button head bolt first through the
Rod End and then through the Hinge Half, Lower Use
the M8 Nylon Lock Nuts to secure the bolt. Mirror and
repeat on other side. Tighten both sides. The
windshield can be horizontally aligned by tightening or
loosening these bolts on each side
Shown above is both assembled Hinge Halves, Upper
and their orientations on the frame of the vehicle.
Taking care to keep the Center Retainer under the
header panel, place the windshield on the frame of
vehicle.
21 22
23 24
9

Now that both strikers are engaged in the Strike
Plates, by loosening the two set screws shown above
in the Brace Mounting Block the cable length can be
changed so that the strikers bottom out in the Strike
Plates without having any excess length that would
make closing the windshield difficult. If there was not
enough length originally, when you loosen the screws
above, the strikers should then bottom out in the
Strike Plates (you may have to compress the gasket
near the strike plates by hand to facilitate this) Pull on
the cut end of the cable to remove any slack and then
re-tighten the screw. Repeat for other cable.
Press the bottom corners of the windshield in gently to
latch the strikers in the Strike Plates.
*do not slam the
windshield closed yet *
it isn’t aligned yet and it may
damage the End Blocks and/or Strike Plates. Once
both strikers are latched in the Strike Plates you can
move to the next step.
25 26
27
10
Twist the T Handle to open the windshield and lift it
until it is parallel with the ground. Have a helper (or
stick) hold the windshield in this position. You will
need it to be open while you do the next few steps.
28
Check the alignment of the windshield. These two
bolts on either side of the windshield can be loosened
to allow for adjustment of the windshield alignment.
Use a rubber mallet to tap them and align the
windshield. Once aligned, tighten all bolts.