Farmet K-300P User manual

web: www.farmet.cz
e-mail: [e-mail]
IČ: 46504931
DIČ: CZ46504931
Farmet a. s.
Jiřinková 276
552 03 Česká Skalice, CZ
telefon: [phone]
fax: [phone]
GSM: [phone]
OPERATING MANUAL
KOMPAKTOMAT
K300P | K400PS | K450PS
Edition: 1 | effective from: 1. 1. 2019

Manual
KOMPAKTOMAT K300P | K400PS | K450PS
2 │44
Dear customer,
Semi-carried machines KOMPAKTOMAT are quality products of Farmet a.s. Česká Skalice.
You can fully utilise the advantages of your machine after thoroughly studying the operating manual.
The serial number of the machine is punched on the production label and written in the operating manual
(see MACHINE SPECIFICATION). This machine serial number must be stated whenever ordering spare parts for
possible repairs. The production label is located on the middle frame near the tow bar.
Use only original spare parts for these machines according to the Spare parts catalogue officially issued by
the manufacturer, Farmet a.s. Ceska Skalice.
POSSIBILITIES OF USE OF YOUR MACHINE
KOMPAKTOMAT je is intended for presowing preparation of soil as a subsequent operation after
ploughing or stubble breaking with incorporated plant residues.
MACHINE SPECIFICATION:
TYPE OF MACHINE KOMPAKTOMAT
SERIAL NUMBER OF MACHINE
USED EQUIPMENT:
...................................................................................................................................................................................
...................................................................................................................................................................................
...................................................................................................................................................................................
...................................................................................................................................................................................
...................................................................................................................................................................................

Manual
KOMPAKTOMAT K300P | K400PS | K450PS
3 │44
CONTENTS
BASIC DESCRIPTION OF THE KOMPAKTOMAT MACHINE .......................................................... 4
Machine limit parameters.......................................................................................................... 6
Safety statement........................................................................................................................ 6
A. GENERAL INSTRUCTIONS FOR USE..................................................................................... 6
Protective tools .......................................................................................................................... 7
B. MACHINE TRANSPORT USING TRANSPORT MEANS .......................................................... 7
C. MACHINE HANDLING USING LIFTING EQUIPMENT ........................................................... 8
D. WORK SAFETY LABELS ........................................................................................................ 8
1. DESCRIPTION.................................................................................................................... 13
2. AGREGATION TO A TRACTOR........................................................................................... 14
3. WORKING PARTS.............................................................................................................. 14
4. MACHINE ASSEMBLY AT THE CUSTOMER........................................................................ 17
5. COMMISSIONING ............................................................................................................. 17
5.1 Agregation to a tractor .............................................................................................. 18
5.2 Hydraulic of the machine .......................................................................................... 19
5.3 Folding and unfolding the machine........................................................................... 22
5.3.1 Folding the machine into the transport position............................................... 22
5.3.2 Unfolding the machine into the working position ............................................. 23
6. MACHINE TRANSPORT ON ROADS................................................................................... 24
7. ADJUSTING THE WORKING PARTS OF THE MACHINE...................................................... 25
7.1 Adjusting the position and depth of the track cultivators ........................................ 25
7.2 Adjusting the spring-mounted front leveller............................................................. 27
7.3 Adjusting the components of working rollers........................................................... 29
7.3.1 RR –ring rollers .................................................................................................. 29
7.4 Adjusting the depth of the share section.................................................................. 29
7.4.1 MCD - mechanical depth setting........................................................................ 30
7.4.2 HD - hydraulic depth setting .............................................................................. 30
7.5 Adjusting the leveller height behind shares.............................................................. 30
7.6 Setting the finishing section features........................................................................ 31
7.6.1 Setting the angle of the rear leveller ..................................................................... 31
7.6.2 setting the pressure of the finishing roller ............................................................ 32
8. AGGREGATION WITH OTHER EQUIPMENT ...................................................................... 32
8.1 Aggregation with pneumatic drill machine ............................................................... 36
9. MAINTENANCE AND REPAIRS OF THE MACHINE............................................................. 37
9.1 Lubrication plan for the machine .............................................................................. 38
9.2 Replacement of worn shares..................................................................................... 39
9.2.1 Replacement of worn shares on the central frame ........................................... 39
9.2.2 Replacement of worn shares of the side frame................................................. 39
10. MACHINE STORAGE –LONG-TERM MACHINE SHUTDOWN:........................................ 40
11. PROTECTION OF ENVIRONMENT .................................................................................. 41
12. MACHINE DISPOSAL AFTER SERVICE LIFE EXPIR ........................................................... 41
13. SERVICING AND WARRANTY CONDITIONS ................................................................... 41
CE CERTIFICATE OF CONFORMITY................................................................................ 43

Manual
KOMPAKTOMAT K300P | K400PS | K450PS
4 │44
BASIC DESCRIPTION OF THE KOMPAKTOMAT MACHINE
The modular concept of the Kompaktomat machine design allows for variable use of its various alternatives.
The machine can be attached to the tractor either via the rear arms of the three-point hitch or via the fixed
bottom hitch. Furthermore, to improve the function in particular conditions, it is possible to change the
working parts of the machine such as the type and number of track cultivators, type of front levellers, type of
front rollers, type of share sections and type of rear rollers. To increase productivity, Kompaktomat machines
can be additionally equipped with hydraulic control of the front leveller position and share depth setting.
The standard version of the semi-carried machine consists of the following parts:
-Carrier bar for connecting to the three-point hitch of the pulling vehicle
-Towing forks with adjustable tractor track cultivators
-Supporting frames of the machine
-The machine is standardly equipped with a mechanical drawbar that secures the side frames in the
transport position
-The machine is standardly equipped with front and rear safety plates with oblique red-and-white hatching
and with taillights and a reflective plate for vehicle marking according to EHK No. 69
Standard Version Working parts
1)
Three-point hitch carrier bar 3
2)
Automatically spring-loaded track cultivators with sweeps
3)
Automatically spring-loaded front levellers with mechanical height adjustment
4)
Front 12-piece slatted roller 400mm
5)
Sweep section on formed springs with a levelling bar and mechanically controlled depth
6)
Rear cross-kill roller with a cleaner
7)
Rear leveller with the option of mechanical adjustment of the leveller angle
1
2
3
4
5
6
7

Manual
KOMPAKTOMAT K300P | K400PS | K450PS
5 │44
TECHNICAL PARAMETERS
K300P
K400PS
K450PS
Working width (mm)
3000
4000
4500
Transport width (mm)
3000
Transport height (mm)
1650
2670
3030
Total length of the machine
(mm)
5965
Working depth (mm)
0-100
Number of shares A/B/C
13/30/12
18/39/16
20/47/20
Working performance (ha/hour)
2,2-3,2
3-4
3,5-4,5
Working speed (km/hour)
8-12
Maximum transport speed
(km/hour)
20
Maximum slope accessibility (°)
6
Tyre dimensions (type)
400/60-15,5 145A8
Tyre pressure (kPa)
350
Max. weight of the machine
(standard version)
2360
3010
3340
Oil filling HLP 46 DIN51524-2 (l)
4
7
Requirement for the engine
power of the tractor (kW)*
70
90
110
Requirement for tractor
aggregation
STANDARD EQUIPMENT
Spacing of the bottom
hitch joints (as
measured on the joint
axes)
870 +/- 1,5 mm
of the bottom hitch
joint holes for the hitch
pins of the machine
STANDARD EQUIPMENT
37.5mm
ABOVE-STANDARD EQUIPMENT
29mm
Requirement for the hydraulic
system of the tractor
STANDARD EQUIPMENT
- Side frame folding
circuit
Pressure in the circuit 200bar, 2 sockets for snap
coupling ISO 12.5
STANDARD EQUIPMENT
- Axle lifting circuit
Pressure in the circuit 200bar, 2 sockets for snap
coupling ISO 12.5
ABOVE-STANDARD
EQUIPMENT
- Front leveller control
circuit
Pressure in the circuit 200bar, 2 sockets for snap
coupling ISO 12.5
ABOVE-STANDARD
EQUIPMENT
- Share depth control
circuit
Pressure in the circuit 200bar, 2 sockets for snap
coupling ISO 12.5
ABOVE-STANDARD
EQUIPMENT
- Drill machine drive fan
circuit
PRESSURE BRANCH –circuit with oil supply
priority
Pressure in the circuit 130bar, 1 socket for snap
coupling ISO 12.5,
Maximum flow 40 l/min
WASTE BRANCH –free waste into the oil tank
Pressure in the circuit 5bar, 1 socket for snap
coupling ISO 20
Requirement for the air system of
the tractor
ABOVE-STANDARD
EQUIPMENT
- Machine axle braking
circuit
Pressure in the circuit at least 6bar –max. 15bar,
2 coupling heads of single-circuit two-hose brakes
* These values are only as recommended tractive equipment. The actual tractive force may substantially differ according to the processing
depth, soil conditions, slope of the land, wear and tear of working parts and their adjustment.

Manual
KOMPAKTOMAT K300P | K400PS | K450PS
6 │44
MACHINE LIMIT PARAMETERS
(x) The machine is to be used for presowing preparation of soil after ploughing or stubble breaking with
working depth from 0 mm to 100 mm for soil cultivation in agriculture. Other uses exceeding the
determined purpose is forbidden.
(x) Machine operation is performed by one person –the tractor driver.
(x) Machine operator must not use the machine in a different way, especially:
(x) Transport of persons and animals on the machine structure,
(x) Transport of burdens on the machine structure,
(x) Aggregation of the machine with another towing equipment than stated in Chapter „5.1./p.18“.
SAFETY STATEMENT
A. GENERAL INSTRUCTIONS FOR USE
A.1 (x) The machine is made in accordance with the latest equipment state and approved safety regulations.
However, dangers of user or third person injury or machine damage or creation of other material
damage may arise during use.
A.2 (xx) Use the machine only in a technically sound condition, in accordance with its purpose, aware of
possible dangers, and while adhering to the safety instructions of this operating manual!
The Manufacturer is not liable for damages caused by the use of the machine that is in contradiction
with the limit parameters of the machine and with the instructions for the use of the machine (Chapter A
and 5). The User bears the risk.
Immediately remove especially the failures that may negatively affect safety!
A.3 (7) Machine operation may be performed by a person authorised by the operator under these conditions:
(8) It must own a valid driver's licence of the corresponding category,
(9) It must be demonstrably familiarised with the safety regulations for work with the machine and
must practically master the machine operation,
(10) The machine may not be operated by juveniles,
(11) It must know the meaning of the safety signs located on the machine. Their respecting is
important for safe and reliable machine operation.
A.4 (12) Maintenance and servicing repairs on the machine may only be performed by a person:
(13) Authorised by the operator,
(14) Educated in the machinery field with knowledge of repairs of similar machines,
(15) Demonstrably familiarised with safety regulations for work with the machine,
16) During a repair of a machine connected to a tractor, it must own a driver's licence of the
corresponding category.
A.5 (17) Machine operator must secure the safety of other persons when working with the machine or
transporting the machine.
This warning sign warns about an immediate dangerous situation
ending with death or severe injury.
This warning sign warns about a dangerous situation ending with
death or severe injury.
This warning sign warns about a situation that may end with a smaller
or slight injury. It also warns about dangerous actions related to the
activity that could lead to an injury.

Manual
KOMPAKTOMAT K300P | K400PS | K450PS
7 │44
A.6 (18) During machine work in the field or during transport, the operator must control the machine from the
tractor's cabin.
A.7 (19) The operator may enter the machine structure only with the machine at rest and blocked against
movement, namely only for these reasons:
(20) Adjustment of the machine working parts,
(21) Repair and maintenance of the machine,
(29) Release and securing of spherical valves of the axle,
(27) Securing of spherical valves of the axle before folding the side frames,
(28) Adjustment of the working parts of the machine after unfolding the side frames.
A.8 (xxx) When stepping on the machine, do not step on tyres of the axles or other rotary parts. Those may
turn and you can cause very serious injuries by the subsequent fall.
A.9 (22) Any changes or modifications of machine may be performed only with written consent of the
manufacturer. For possible damage arisen due to ignoring this instruction, the producer bears no
responsibility. The machine must be maintained equipped with prescribed accessories and equipment
including safety marking. All warning and safety signs must be legible and in their places. In case of
damage or loss, these signs must be immediately renewed.
A.10 (23) The operator must have the Operating Manual with the work safety requirements available at any
time when working with the machine.
A.11 (24) The operator must not consume alcohol, medicines, narcotic and hallucinogenic substances that
decrease his attention and coordination capabilities while using the machine. If the operator must use
medicines prescribed by a physician or uses freely sold medicines, he must be informed by a physician,
whether he is capable of responsible and safe operation of the machine under these circumstances.
PROTECTIVE TOOLS
For the operation and maintenance use:
Tight clothes
Protective gloves and goggles for protection against dust and sharp parts of the machine
B. MACHINE TRANSPORT USING TRANSPORT MEANS
B.1 (1) The transport means designed for machine transport must have the load capacity minimally identical
with the weight of the transported machine. The total weight of the machine is stated on the production
label.
B.2 (2) The dimensions of the transported machine including the transport means must comply with the valid
regulations for road traffic (decrees, laws).
B.3 (3) The transported machine must be always fastened to the transport means so that its spontaneous
loosening could not happen.
B.4 (4) The carrier is responsible for damage caused by the loosening of incorrectly or insufficiently fastened
machine to the transport means.
B.5 (xx) The carrier shall observe the instructions of the responsible employees of Farmet in charge of loading
concerning proper binding and securing of the machine on the transportation vehicle, particularly with
regard to the potential damage of the machine to be transported.

Manual
KOMPAKTOMAT K300P | K400PS | K450PS
8 │44
C. MACHINE HANDLING USING LIFTING EQUIPMENT
C.1 (1) The lifting equipment and tying means designed for handling of the machine must have their load
capacity at least identical with the weight of the handled machine.
C.2 (2) Machine fastening for handling may only be performed in places designed for that and marked with
self-adhesive labels showing the "chain" symbol.
C.3 (3) After fastening (suspending) at designated points, it is forbidden to move in the space of possible
reach of the handled machine.
C.4 Table with approximate weights of the parts according to the loading alternative
K300P
K400PS
K450PS
TOWING FORK
(kg)
200
200
200
CENTRAL FRAME
(kg)
800
800
800
FORK+CENTRAL FRAME
(kg)
1000
1000
1000
RIGHT SIDE FRAME
(kg)
1140
1100
1300
LEFT SIDE FRAME
(kg)
-
1100
1300
EXTERIOR RIGHT SIDE FRAME
(kg)
-
-
-
EXTERIOR LEFT SIDE FRAME
(kg)
220
-
-
AXLE
(kg)
2360
300
300
MACHINE
(kg)
200
3150
3400
D. WORK SAFETY LABELS
Warning safety labels serve for operator protection.
THE FOLLOWING APPLIES GENERALLY:
D.1 Strictly observe the warning safety labels.
D.2 All safety instructions also apply to other users.
D.3 The operator shall ensure completeness and readability of labels on the machine, i.e. the operator shall
replace any damaged labels with new ones.
D.4 The appearance and exact meaning of the warning safety labels on the machine are specified in the
following table.
WARNING SAFETY LABELS
TEXT TO THE LABELS
POSITION ON THE
MACHINE
Before handling the machine, carefully read the
operating manual.
Observe the instructions and safety regulations
for machine operation during use.
P 1 H
When connecting or disconnecting, do not step
between the tractor and the machine, also do
not enter this space, if the tractor and the
machine are not at rest and the engine is not
turned off.
P 2 H
Stay outside the reach of the tractor -
agricultural machine set, if the tractor engine is
in operation.
P 6 H

Manual
KOMPAKTOMAT K300P | K400PS | K450PS
9 │44
Secure the side frames against unfolding and the
axle against sudden fall prior to the
transportation of the machine.
P 13 H
When unfolding the side frames into the
transport position, do not reach into the area of
contact with the central frame.
P 20 H
Driving the machine and transportation on its
construction is strictly forbidden.
P 37 H
When working and transporting the machine,
maintain safe distance from the electric
appliances.
P 39 H
Stay outside the reach of the unsecured side
frames of the machine.
P 50 H
Do not approach the rotary parts of the machine
unless they are standing still, i.e. they are not
rotating.
P 53 H
It is strictly folding and unfolding the side frames
on slopes or inclined surfaces.
P 100 H
The shown positions of the handle and the
function of the hydraulic ball valve located on
the piston-rod.
P 101 H
This indicates areas for hanging using handling
equipment.
D.5 The positions of the warning safety labels on the machine are shown in the following pictures.

Manual
KOMPAKTOMAT K300P | K400PS | K450PS
10 │44
K300P - Front view
K300P - Rear view
P1H
P1H
P101H, P13H
P101H, P13H
P37H
P53H
P37H
P53H
P1H
P2H
P6H
P101H
P1H

Manual
KOMPAKTOMAT K300P | K400PS | K450PS
11 │44
K400PS, K450PS –Front view
P1H
P2H
P6H
P101H
P1H
P20H
P39H
P50H
P37H
P53H
P101H, P13H
P101H, P13H
P37H
P53H
P39H
P50H
P1H
P20H
P13H
P13H

Manual
KOMPAKTOMAT K300P | K400PS | K450PS
12 │44
K400PS, K450PS –Rear view
P37H
P53H
P37H
P53H
P39H
P50H
P39H
P50H
P1H
P20H

Manual
KOMPAKTOMAT K300P | K400PS | K450PS
13 │44
1. DESCRIPTION
Kompaktomat is structurally designed as a semi-carried folding machine aggregated behind a tractor. The
machine consists of a towing fork and supporting frames where the individual working parts are installed. The
modular design of the machine allows selecting various types of working parts so that the machine meets the
high demands of any soil conditions.
The basic version of the machine (see p. 4) combines seven soil-processing operations in a single pass.
The control for folding the side frames into the transport or working position is designed as a single
independent hydraulic circuit controlled by the driver in the tractor cabin.
The control of the axle in the transport or working position is designed as a single independent hydraulic
circuit controlled by the driver in the tractor cabin.
All Kompaktomat machines meet the regulations for road transportation.
The design of the Kompaktomat machine allows using a whole range of additional equipment to increase
productivity and efficiency, such as the automatic front leveller position control system using an independent
hydraulic circuit controlled by the driver in the tractor cabin, or the automatic share depth control using an
independent hydraulic circuit controlled by the driver in the tractor cabin. Kompaktomat may also be equipped
with a rear three-point hitch 2 which allows aggregating other pieces of equipment for soil processing or a
pneumatic drill machine behind Kompaktomat.
Track cultivator
with sweeps
Front leveller
Front bar roller
Sweep section
Levelling bar
Rear crumbling
roller
Rear finishing
leveller
3-point hitch
towing work 3

Manual
KOMPAKTOMAT K300P | K400PS | K450PS
14 │44
2. AGREGATION TO A TRACTOR
VERSION –TBZ
Aggregation of the machine to the rear arms of the tractor in the
category TBZ (three-point hitch). You can choose pins for categories
TBZ2=ø28mm, TBZ3=ø36mm, TBZ4=ø50mm.
VERSION –C40; C50; C70
Aggregation of the machine to the fixed bottom hitch with a pulling
loop with the diameter of 40mm, 50mm or 70mm.
This is offered as the optional equipment of the machine.
VERSION –K80
Aggregation of the machine to the fixed bottom hitch with a K80
ball.
This is offered as the optional equipment of the machine.
3. WORKING PARTS
TRACK CULTIVATOR
CA –Track Cultivator with Sweep
Automatically released tractor track cultivator with a sweep. Suitable for
loose types of soil where there is no risk of formation of wet clods. Possibility
of mechanical depth setting up to 80mm. Possibility of setting the position
directly behind the tractor wheels.
CC –Track Cultivator with Chisel Share
Automatically released tractor track cultivator with a chisel share. Suitable
for heavier types of soil where there is no risk of formation of wet clods.
Possibility of mechanical depth setting up to 80mm. Possibility of setting the
position directly behind the tractor.
FRONT LEVELLERS
FL –Front Fixed Serrated Levelling Bar
Automatically released levelling bar with a serrated section. Massive
construction for precise levelling of coarse furrows. You can choose either
manual adjustment of the leveller height or hydraulically controlled leveller
height.
L –Front Levelling Bar with Flexible Segments
Automatically released levelling bar with separate flexible segments. Better
clod crumbling. You can choose either manual adjustment of the leveller
height or hydraulically controlled leveller height.

Manual
KOMPAKTOMAT K300P | K400PS | K450PS
15 │44
WORKING ROLLERS
SB –Spiral Bar Roller - 40 cm - 60 kg/m
Quality clod crumbling. Suitable for humid conditions.
This type of roller can be used as the FRONT or REAR roller.
BR –Bar Roller - 40 cm - 60 kg/m
High-quality clod crumbling. Not suitable for humid conditions.
This type of roller can be used as the FRONT or REAR roller..
RR –Ring Roller 40 cm - 115 kg/m
Quality work in all types of soil, good depth guiding, suitable for more humid
soils.
This type of roller can be used as the FRONT or REAR roller.
CR - Cross-kill Roller - 40 cm - 170 kg/m
Excellent work in light, medium and heavy soils, quality compaction and clod
crumbling.
This type of roller can be used as the REAR roller only.
DCR –Double-row Cross-kill Roller - 40 cm / 40 cm - 175 kg/m
Excellent work in light, medium and heavy soils, quality compaction and clod
crumbling.
This type of roller can be used as the REAR roller only.
BR
SB
CR
DCR
RR
Crumbling
●●●○
●●●○
●●●●
●●●●
●●○○
Compacting
●●●○
●●●○
●●●●
●●●●
●●●●
Depth guiding
●●●●
●●●●
●○○○
●●○○
●●●●
Resistance to clogging
●●○○
●●●○
●●●○
●●●●
●●●●
Suitable for rocky soils
●●●○
●●●○
●●○○
●○○○
●●●○
Suitable for wet soils
●○○○
●●●○
●●○○
●●●○
●●●●
Heavy soils
●●○○
●●○○
●●●○
●●●○
●●●○
Medium soils
●●●○
●●●○
●●●●
●●●●
●●●○
Light soils
●●●●
●●●●
●●●●
●●●●
●●●○
● –MAX / ○ - MIN
SHARE SECTIONS
AL –Section
The share section is equipped with sweeps with the width of 25 cm
in two rows. Each sweep is protected by a leaf spring. This section
is suitable for lighter soil conditions without plant residues. There
is a leveller behind the sweeps.

Manual
KOMPAKTOMAT K300P | K400PS | K450PS
16 │44
CF –Section
The share section is equipped with slim chisels with the width of 7
cm in four rows. The section is suitable for processing soil in spring
when it is not suitable to pull wet soil out to the surface, or for
heavy soils. There is no leveller behind the chisels.
AP –Section
A universal share section is equipped with sweeps with the width
of 25 cm in two rows. The sweeps are mounted to frames with
geometry improving the permeability of plant residues. Therefore,
this section is suitable for land with a higher occurrence of crushed
plant residues as well as for heavy soils. There is a leveller behind
the sweeps.
AL
CF
AP
Number of rows of shares (pieces) / Row
spacing (mm)
2 / 400
4 / 240
2 / 490
Leveller behind shares
●●●●
○○○○
●●●●
All-area processing
●●●●
●●●○
●●●●
Suitable for light soils
●●●●
●●●●
●●●●
Suitable for medium soils
●●●○
●●●○
●●●●
Suitable for heavy soils
●●●○
●●●○
●●●●
Suitable for rocky soils
●●●○
●●●○
●●●●
Suitable for wet soils
●●○○
●●●●
●●○○
Resistance to clogging
●●○○
●●●○
●●●○
● –MAX / ○ - MIN
LEVELLING BARS BEHIND SHARES
LEVELLING BAR BEHIND SHARES
The levelling bar is applied behind the share sections. The bar is used
for levelling the loosened soil in front of the rear roller.
FINISHING OPERATIONS
LF - REAR FINISHING LEVELLING BAR
The levelling bar behind the rear roller levels and evenly spreads the
loosened soil.
RF - REAR FINISHING ROLLER
The finishing roller actively disintegrates any remaining clods behind the
rear roller. Be careful –the finishing roller cannot be used behind the two-
row crosskill rollers.

Manual
KOMPAKTOMAT K300P | K400PS | K450PS
17 │44
4. MACHINE ASSEMBLY AT THE CUSTOMER
Always assemble the machine on a flat and reinforced surface.
Use the Spare Parts Catalogue with 3D views as reference for assembly.
The operator must perform the assembly according to the instructions of the producer, best in
cooperation with the expert servicing technician determined by the producer.
The operator must secure a functional test of all assembled parts after the completion of the machine
assembly.
The operator must secure that the handling of the machine using lifting equipment during its assembly is
in accordance with chapter „C“/p.8.
Example of a loaded machine, K800PS, on the truck platform
Unloading the K800PS machine from the truck platform using a forklift truck
5. COMMISSIONING
Before taking over the machine, test and check, whether damage occurred during transport and
whether all parts contained in the bill of delivery were supplied.
Before commissioning the machine, carefully read this operating manual, especially Chapters A-D page
6-11. Before the first use of the machine, familiarise yourselves with its controls and overall function.
During work with the machine, observe not only the instructions of this operating manual but also
generally valid regulations of work safety, health protection, fire and transport safety, and
environmental protection.

Manual
KOMPAKTOMAT K300P | K400PS | K450PS
18 │44
The operator must check the machine before every use (commissioning) from the standpoint of
completeness, work safety, work hygiene, fire safety, transport safety, and environmental protection.
A MACHINE SHOWING SIGNS OF DAMAGE MUST NOT BE COMMISSIONED!!
Aggregation of the machine with the tractor is to be performed on a flat and hardened surface.
When working on slopes, observe the lowest slope grade of the set TRACTOR - MACHINE.
Before starting the tractor motor, check whether no person or animal is in the working space of the set
and push the warning sound signal.
The operator is responsible for the safety and all damage caused by the operation of the tractor and the
connected machine.
The operator is obliged to adhere to the technical and safety regulations of the machine determined by
the producer when working.
The operator must raise the machine when turning at the plough turning end, i.e. the working parts
must not be in the ground.
The operator is obliged to observe the prescribed working depths and speeds stated in the manual in
table page 5 when working with the machine.
The operator is obliged to lower the machine to the ground and secure the set against movement
before leaving the tractor cabin.
When connecting, no persons may stay in the space between the tractor and the machine. Exercise
utmost caution!
5.1 AGREGATION TO A TRACTOR
The machine can be connected only to a tractor, whose curb weight is identical or higher than the
overall weight of the connected machine.
The machine operator must observe all generally valid regulations of work safety, health protection, fire
safety, and environmental protection.
The operator may connect the machine exclusively to a tractor that is equipped with a rear three-point
hitch or lower agro tow bar and a functional undamaged hydraulic system.
The controlling distributors in the tractor must be secured or blocked when the machine is in the
transport position or when the machine is not in use to prevent accidental or third-party (children,
passengers) caused movement of the hydraulics.
Aggregate the machine with the tractor using type and dimensionally consistent components
corresponding to the output requirements. For example, do not aggregate a machine with ø50mm
pulling loop to ø40mm pin!
The design allows selecting from several versions of aggregation to the tractor.
Aggregation to the rear TBZ hitch Aggregation to the agro tow bar

Manual
KOMPAKTOMAT K300P | K400PS | K450PS
19 │44
5.2 HYDRAULIC OF THE MACHINE
Parts of the hydraulic system of the machine, which are under pressure, are forbidden to disassemble.
Hydraulic oil that penetrates the skin under high pressure causes severe injuries. In case of injury, seek a
physician immediately.
Connect the hydraulics only when the hydraulic circuits of the machine and the tractor (aggregate) are in
a pressure-less condition.
The hydraulic system is under high pressure. Regularly check for leaks and immediately remove obvious
damage of all lines, hoses, and pipe unions.
When seeking and removing leaks, use only the suitable tools.
For connecting the hydraulic system of the machine to the tractor, use the plug (on the machine) and
the socket (on the tractor) of the quick-couplers of the same type.
For simplification, the hydraulic circuits are marked by different colours.
STANDARD EQUIPMENT OF THE MACHINE
HYDRAULIC CIRCUIT FOR SIDE FRAME FOLDING
- ONE RED RING
Pressurizing this branch of the circuit folds side frames into the transport position.
HYDRAULIC CIRCUIT FOR SIDE FRAME FOLDING
- TWO RED RINGS
Pressurizing this branch of the circuit unfolds side frames into the working position.
HYDRAULIC CIRCUIT FOR AXLE CONTROL
- ONE YELLOW RING
Pressurizing this branch of the circuit brings the axle into the position when the
machine rides on the working rollers and the axle wheels are in the air.
HYDRAULIC CIRCUIT FOR AXLE CONTROL
- TWO RED RINGS
Pressurizing this branch of the circuit lifts the transport axle into the transport
position, i.e. the machine rides on the axle tyres.
OPTIONAL EQUIPMENT OF THE MACHINE
HYDRAULIC CIRCUIT FOR FRONT LEVELLER POSITION CONTROL
- ONE BLUE RING
Pressurizing this branch of the circuit brings the leveller up from the surface.
HYDRAULIC CIRCUIT FOR FRONT LEVELLER POSITION CONTROL
- TWO BLUE RINGS
Pressurizing this branch of the circuit recesses the leveller to the surface.
HYDRAULIC CIRCUIT FOR SHARE WORKING DEPTH CONTROL
- ONE GREEN RING
Pressurizing this branch of the circuit brings shares out of the processed profile.
HYDRAULIC CIRCUIT FOR SHARE WORKING DEPTH CONTROL
- TWO GREEN RINGS
Pressurizing this branch of the circuit recesses shares into the processed profile.
HYDRAULIC CIRCUIT FOR DRILL MACHINE FAN FLUID MOTOR DRIVE
- ONE BLACK RING
The Dn20 circuit branch is used for draining oil directly into the oil tank of the tractor.
The maximum permissible pressure in the waste hose is 5 bar; higher pressure
pushes the shaft sealing out which damages the fluid motor fan.
If no suitable outlet into the tank is not installed in the tractor, consult the
manufacturer (dealer) of the tractor who will provide information about the
possibilities of a free waste end piece.
HYDRAULIC CIRCUIT FOR DRILL MACHINE FAN FLUID MOTOR DRIVE
- TWO BLACK RINGS
The Dn12 circuit branch is connected to the circuit with oil delivery priority.
Pressurizing this branch of the circuit delivers oil to the fluid motor drive of the fan.
The maximum permissible pressure is 130 bar, maximum flow rate is 40 l/min.

Manual
KOMPAKTOMAT K300P | K400PS | K450PS
20 │44
Hydraulic diagram K300P
1-Control distributor in the tractor
2-Hydraulic snap couplings
3-Hydraulic cylinders of share depth control
4-Hydraulic closing valve for share depth
cylinders
radlic
1-Control distributor in the tractor
2-Hydraulic snap couplings
3-Hydraulic cylinders of leveller control
4-Hydraulic closing valve for leveller
cylinders
1-Control distributor in the tractor
2-Hydraulic snap couplings
3-Hydraulic cylinders of the axle control
4-Closing taps of the axle cylinders