Farmet KOMPAKTOMAT K1250PS User manual

web: www.farmet.cz
e-mail: [e-mail]
IČ: 46504931
DIČ: CZ46504931
Farmet a. s.
Jiřinková 276
552 03 Česká Skalice, CZ
telefon: [phone]
fax: [phone]
GSM: [phone]
OPERATING MANUAL
KOMPAKTOMAT
K1250PS | K1570PS
Edition: 5 | effective from: 1. 1. 2021

Manual
KOMPAKTOMAT K1250PS | K1570PS
2 │46
Dear customer,
Semi-carried machines KOMPAKTOMAT are quality products of Farmet a.s. Česká Skalice.
You can fully utilise the advantages of your machine after thoroughly studying the operating manual.
The serial number of the machine is punched on the production label and written in the operating manual
(see Tabl.1). This machine serial number must be stated whenever ordering spare parts for possible repairs.
The production label is located on the middle frame near the tow bar.
Use only original spare parts for these machines according to the Spare parts catalogue officially issued by
the manufacturer, Farmet a.s. Ceska Skalice.
Possibilities of Use of Your Machine
Kompaktomat is intended for presowing preparation of soil as a subsequent operation after ploughing
or stubble breaking. The machine is intended for tractors with the output of 243-316 kW (See Chapter E.3/Page
5-6). Optimal speed for soil processing is 8-12 km/hour.
Tabl. 1- Characteristics of the machine
TYPE OF MACHINE
SERIAL NUMBER OF MACHINE
SPECIAL VERSION OR ACCESSORIES:
...................................................................................................................................................................................
...................................................................................................................................................................................
...................................................................................................................................................................................
...................................................................................................................................................................................
...................................................................................................................................................................................

Manual
KOMPAKTOMAT K1250PS | K1570PS
3 │46
CONTENTS
A. LIMITING PARAMETERS.................................................................................................................................. 4
B. MACHINE TRANSPORT USING TRANSPORT MEANS ....................................................................................... 5
C. MACHINE HANDLING USING LIFTING EQUIPMENT ........................................................................................ 5
D. ASSEMBLY AT THE CUSTOMER´S PLACE ......................................................................................................... 5
E. AGREGATION WITH THE TRACTOR................................................................................................................. 5
F. FOLDING AND UNFOLDING THE MACHINE..................................................................................................... 6
G. ROAD TRANSPORTATION................................................................................................................................ 6
H. OPERATING THE MACHINE IN THE FIELD ....................................................................................................... 7
I. MACHINE ADJUSTMENT ................................................................................................................................. 7
J. STORAGE......................................................................................................................................................... 7
K. MACHINE REPAIRS.......................................................................................................................................... 8
L. REPLACEMENT OF WORN-AND-TORN SHARES .............................................................................................. 8
M. MACHINE DISPOSAL AFTER ITS SERVICE LIFE ................................................................................................. 8
1. MACHINE DESCRIPTION................................................................................................................................ 12
1.1 Aggregation to a tractor ...................................................................................................................... 12
1.2 Working parts ...................................................................................................................................... 12
2. SPECIFICATIONS............................................................................................................................................ 16
3. OPERATIONAL SAFETY RULES ....................................................................................................................... 17
4. ROAD TRANSPORT RULES............................................................................................................................. 17
5. SETTING TO WORK ....................................................................................................................................... 18
6. AGREGATION WITH THE TRACTOR............................................................................................................... 22
7. PROCEDURE FOR UNFOLDING INTO THE WORKING POSITION.................................................................... 22
8. PROCEDURE FOR FOLDING INTO THE TRANSPORT POSITION...................................................................... 25
9. ADJUSTING THE WORKING PARTS OF THE MACHINE................................................................................... 27
9.1 Adjusting the position and depth of the track cultivators................................................................... 28
9.2 Adjusting the spring mounted front leveller ....................................................................................... 29
9.2.1 FL + FH –Front fixed serrated levelling bar..................................................................................... 30
9.3 Adjusting the components of RING rollers .......................................................................................... 30
9.4 Adjusting the depth of the share section ............................................................................................ 31
9.4.1 MCD-mechanical depth setting....................................................................................................... 32
9.4.2 HD-hydraulic depth setting ............................................................................................................. 32
9.5 Adjusting the leveller height behind shares ........................................................................................ 32
9.6 Setting the finishing section features .................................................................................................. 33
9.6.1 Setting the angle of the rear leveller............................................................................................... 33
9.6.2 Setting the pressure of the finishing roller...................................................................................... 33
9.7 Pre-stressing tractive ropes................................................................................................................. 34
10. FIELD WORK POSSIBILITIES FOR THE MACHINE............................................................................................ 35
11. BRAKE DISTRIBUTION OF THE MACHINE...................................................................................................... 37
12. EXCHANGING THE WORKING TOOLS............................................................................................................ 37
12.1 Replacement of the working roller bearings ....................................................................................... 37
12.1.1 Using spacer................................................................................................................................ 38
13. MAINTENANCE AND REPAIRS....................................................................................................................... 39
14. LUBRICATION PLAN FOR THE MACHINE....................................................................................................... 43
15. ENVORONMENTAL PROTECTION.................................................................................................................. 44
16. MACHINE DISPOSAL AFTER SERVICE LIFE EXPIRY......................................................................................... 44
17. SERVICES AND WARRANTY CONDITIONS ..................................................................................................... 44

Manual
KOMPAKTOMAT K1250PS | K1570PS
4 │46
A. LIMITING PARAMETERS
A.1 (1) Operator(s) may use the machine for agricultural purposes only as an exchangeable implement
aggregated with a tractor.
A.2 (25) Operator(s) may use the machine only for soil preparation before sowing as a follow-up operation
after ploughing or stubble ploughing in the field.
A.3 (3) Operator(s) must not use the machine for other purposes, especially:
(4) Transporting persons on the machine,
(5) Transporting loads on the machine,
(6) Aggregating the machine with a towing vehicle other than that mentioned in Chapter „E.3“.
A.4 (7) Machine operation may be performed by a person authorised by the operator under these
conditions:
(8) It must own a valid driver's licence of the corresponding category,
(9) It must be demonstrably familiarised with the safety regulations for work with the machine and
must practically master the machine operation,
(10) The machine may not be operated by juveniles,
(11) It must know the meaning of the safety signs located on the machine. Their respecting is
important for safe and reliable machine operation.
A.5 (12) Maintenance and servicing repairs on the machine may only be performed by a person:
(13) Authorised by the operator,
(14) Educated in the machinery field with knowledge of repairs of similar machines,
(15) Demonstrably familiarised with safety regulations for work with the machine,
(16) During a repair of a machine connected to a tractor, it must own a driver's licence of the
corresponding category.
A.6 (17) Machine operator must secure the safety of other persons when working with the machine or
transporting the machine.
A.7 (18) During machine work in the field or during transport, the operator must control the machine from
the tractor's cabin.
A.8 (19) The operator may enter the machine structure only with the machine at rest and blocked against
movement, namely only for these reasons:
(20) Adjustment of the machine working parts,
(21) Repair and maintenance of the machine,
(29) Release and securing of spherical valves of the axle,
(27) Securing of spherical valves of the axle before folding the side frames,
(28) Adjustment of the working parts of the machine after unfolding the side frames.
A.9 (22) Any changes or modifications of machine may be performed only with written consent of the
manufacturer. For possible damage arisen due to ignoring this instruction, the producer bears no
responsibility. The machine must be maintained equipped with prescribed accessories and equipment
including safety marking. All warning and safety signs must be legible and in their places. In case of
damage or loss, these signs must be immediately renewed.
A.10 (23) The operator must have the Operating Manual with the work safety requirements available at any
time when working with the machine.
A.11 (24) The operator must not consume alcohol, medicines, narcotic and hallucinogenic substances that
decrease his attention and coordination capabilities while using the machine. If the operator must use
medicines prescribed by a physician or uses freely sold medicines, he must be informed by a physician,
whether he is capable of responsible and safe operation of the machine under these circumstances.

Manual
KOMPAKTOMAT K1250PS | K1570PS
5 │46
B. MACHINE TRANSPORT USING TRANSPORT MEANS
B.1 (1) The transport means designed for machine transport must have the load capacity minimally identical
with the weight of the transported machine. The total weight of the machine is stated on the production
label.
B.2 (2) The dimensions of the transported machine including the transport means must comply with the valid
regulations for road traffic (decrees, laws).
B.3 (3) The transported machine must be always fastened to the transport means so that its spontaneous
loosening could not happen.
B.4 (4) The carrier is responsible for damage caused by the loosening of incorrectly or insufficiently fastened
machine to the transport means.
B.5 (5) If transported on another vehicle, the machine must be disassembled.
C. MACHINE HANDLING USING LIFTING EQUIPMENT
C.1 (1) The lifting equipment and tying means designed for handling of the machine must have their load
capacity at least identical with the weight of the handled machine.
C.2 (2) Machine fastening for handling may only be performed in places designed for that and marked with
self-adhesive labels showing the "chain" symbol.
C.3 (3) After fastening (suspending) at designated points, it is forbidden to move in the space of possible reach
of the handled machine.
D. ASSEMBLY AT THE CUSTOMER´S PLACE
D.1 (1) The operator should assemble the machine according to the manufacturer's instructions. Cooperation
with a serviceman/technician authorized by the manufacturer is advisable.
D.2 (2) After the assembly is completed, the operator should ensure that all the assembled parts are
functional and work smoothly
D.3 (3) The operator should ensure that handling the machine by using the hoisting mechanism when
assembling it is in compliance with Chapter „C“ above.
E. AGREGATION WITH THE TRACTOR
E.1 (1) The operator must observe all general labour-safety, fire-protection and environmental regulations.
E.2 (2) The operator may hitch up the machine solely to such a tractor that is provided with a rear three-
point suspension and a functional undamaged hydraulic system.
E.3 (3) Towing vehicle requirements.
(5) Tractor Engine Output Requirements for K 1250 PS
243 kW
(5) Tractor Engine Output Requirements for K 1570 PS
316 kW
(xx) Tractor three-point suspension
requirements
(xx) of the lower hitch bolt
50 mm
(xx) lower hitch height
480 - 550 mm
(9) Tractor hydraulic system requirements
(xx) side frame unfolding and trail
cultivator recess control circuit
The pressure in the
circuit: 200 bar, two
ISO 12.5 quick coupler
sockets

Manual
KOMPAKTOMAT K1250PS | K1570PS
6 │46
(xx) catch and tracing wheel control
circuit
The pressure in the
circuit: 200 bar, two
ISO 12.5 quick coupler
sockets
(xx)position of the track cultivators
control circuit
The pressure in the
circuit: 200 bar, two
ISO 12.5 quick coupler
sockets
(xx) supporting leg control circuit
The pressure in the
circuit: 200 bar, two
ISO 12.5 quick coupler
sockets
(xx) K 1570 PS side frame unfolding
circuit
The pressure in the
circuit: 200 bar, two
ISO 12.5 quick coupler
sockets
(12) Tractor air system requirements
(13) The machine axle brake circuit
(16) The pressure in the
circuit: min.6 bar –
max. 8 bar, one single-
circuit brake coupling
head
E.4 (xx) Before aggregating the machine with the tractor (especially with those not provided with a quick
suspension device), the operator must secure the tractor against undesirable movement. Especially with
tractors not provided with a quick suspension device, the operator should arrange for another trained
person to cooperate. Such a person must not step into the suspension area before the tractor is secured
against undesirable movement. With tractors provided with a quick suspension device, this operation
can be made by the operator from the tractor driver's seat.
E.5 (17) Aggregating the hydraulic system of the machine with the hydraulic system of the tractor should be
performed according to Chapter 5of this Operating manual.
F. FOLDING AND UNFOLDING THE MACHINE
F.1 (xx) Operator(s) must ensure that no person or animal is within the reach of the lateral frames when
folding and/or unfolding them. Nobody should insert the fingers into the joint space.
F.2 (xx) Before unlocking the connecting rod, the operator(s) must secure the set against undesirable motion
and check (from the tractor cab) by using the hydraulic system control levers whether or not there is oil
in the piston rods. Only after the operator is sure that there is oil in the piston rod, may he proceed to
unlocking the connection rod.
G. ROAD TRANSPORTATION
G.1 (1) The transportation speed of the tractor with the machine should not exceed the maximum transport
speed and the maximum slope accessibility indicated.
G.2 (2) When transported on public roads, increased guardedness should be observed due to the machine
dimensions.
G.3 (3) When transporting on public roads the machine should be provided with a functional set of warning
lights that must be on. If possible, the highest point of the set (usually the tractor roof) should be
provided with a yellow flashing beacon. Moreover, the machine should be provided with the
"maximum-speed" sign, with red-and-white-hatched boards at the machine contours and with rear
reflectors and reflecting board according to the respective regulations.
G.4 (6) The machine should not be transported at poor visibility.

Manual
KOMPAKTOMAT K1250PS | K1570PS
7 │46
G.5 (7) Note that the driving properties of the set change when towed by a tractor on the road due to
different axle loads. Please have this in mind when transporting the machine. The respective road-
transport rules should be strictly observed.
G.6 (8) The operator is obliged to produce the respective certificate of roadworthiness (the MOT Certificate)
if necessary.
G.7 (9) When transporting the machine on public roads, all the respective traffic rules and traffic signs should
be observed.
G.8 (10) When making U-turns or driving reverse gear, be especially careful. Ensure a good outlook from the
tractor cab and use another (instructed and authorized) person if necessary.
G.9 (11) When transporting the machine off public roads, operator(s) should not exceed the lowest maximum
transport speed and the lowest maximum slope accessibility indicated wherever on the set.
G.10 (xx)The operator must secure the folded side frames by the connecting rod to prevent their unfolding
before the start of transportation on ground communications.
H. OPERATING THE MACHINE IN THE FIELD
H.1 (1) The operator should acquaint himself with the machine controls before the first use of the machine.
H.2 (2) Before setting the machine to work, please read the Instructions for use carefully. Pay attention to
labour protection, safe operation and transportation, environmental protection, setting the machine
and its maintenance.
H.3 (3) The operator is responsible for all damages incurred by improper operation of the tractor and the
coupled machine.
H.4 (4) When operating the machine, the operator is obliged to observe all the technical and safety regulation
set by the manufacturer.
H.5 (6) When operating the machine, the operator should observe the prescribed working depths and speeds
given in Chapter 2/Page 16 of this manual.
H.6 (7) When leaving the tractor cab, the operator is obliged to lower the machine onto the ground and
secure it against undesirable motion.
I. MACHINE ADJUSTMENT
I.1 (1) When adjusting the working tools of the machine, the operator should follow the values
recommended in Chapter 9/Pages 27 to 34. Please observe the labour safety principles.
I.2 (2) The machine working tools may be adjusted at rest only with the machine secured against undesirable
motion.
I.3 (3) Working tools adjustments should be done on a flat and paved surface so that the soil cultivation is
performed evenly.
J. STORAGE
J.1 (1) Before storing the machine, the machine should be thoroughly cleaned and preserved in such a
manner that no damage can occur. Special attention should be paid to all the lubrication points
indicated. These points should be lubricated thoroughly according to the Lubrication Chart, see Chapter
14./Page 43.

Manual
KOMPAKTOMAT K1250PS | K1570PS
8 │46
J.2 (xx)It is recommended to store the machine in the transport position, i.e. the side frames folded and
secured by the connecting rod and the machine resting on the supporting leg. The operator must secure
the stored machine from spontaneous movement by activating the hand brake of the machine.
J.3 (3) The operator is obliged to secure the storage place against unauthorized persons' entrance.
K. MACHINE REPAIRS
K.1 (1) Servicing and maintaining the machine can only be carried out by qualified persons duly authorized by
the operator, see Chapter A.4.
K.2 (2) Any machine repairs may only be made at rest, i.e. the machine does not work. If it is necessary for
the machine to be coupled with the tractor during the repair, the ignition key must be removed from
the switchbox.
K.3 (5) All kinds of the machine hydraulic circuit repairs may only be made under the following conditions:
(6) The lateral frames are unfolded,
(7) The machine must rest on the shares and rollers;
(8) The machine must be secured against undesirable motion;
(9) The machine hydraulic circuit must be disconnected from the tractor hydraulic circuit;
(10) The machine vicinity must be protected from being contaminated by hydraulic oil;
(11) The machine must not rest on the axle.
K.4 (3) Any machine repairs should be made in service shops.
K.5 (12) Before repairing the machine hydraulic circuits, the repairman must eliminate pressure in the
hydraulic circuits with the control levers in the tractor cab. This should be done by moving the levers to
their extreme positions back and forth (approx. five times) with the tractor engine stopped.
K.6 (4) When handling the machine with a lifting device, the regulations set forth in Chapter Cshould be
strictly observed.
L. REPLACEMENT OF WORN-AND-TORN SHARES
L.1 (xx) The operator or the serviceman must observe generally valid safety regulations during any
replacement of working bodies.
L.2 (1) The shares should be replaced by the serviceman or operator on a flat and paved surface only.
L.3 (2) When replacing the shares, the machine must be aggregated with the tractor according to Chapter E.
When replacing the shares, the tractor engine must be stopped and the tractor cab secured against
unauthorized entrance or operation.
L.3 (5) If there is a leakage from the tractor hydraulic system, the repairing person is obliged to support the
machine shaft mechanically.
M. MACHINE DISPOSAL AFTER ITS SERVICE LIFE
M.1 (xx) The owner shall observe generally valid safety regulations in case of any disposal.
M.2 (1) The operator must ensure that the machine is secured against undesirable motion before starting the
disposal operations.
M.3 (2) The operator must ensure that metal parts are separated from those parts that contain hydraulic oil
or grease.

Manual
KOMPAKTOMAT K1250PS | K1570PS
9 │46
M.4 (3) Steel parts must be cut up and delivered to the respective salvage point. The other secondary raw
materials should be disposed according to the applicable waste management regulations.
M.5 (4) The operator should ensure that handling the machine with the lifting device is in compliance with
Chapter C.
M.6 (5) Before disposing the machine hydraulic circuits, the repairman must eliminate pressure in the
hydraulic circuits with the control levers in the tractor cab. This should be done by moving the levers to
their extreme positions back and forth (approx. five times) with the tractor engine stopped.
N. LABOUR-PROTECTION STICKERS
The labour-protection stickers protect operators.
Generally:
A) Strictly adhere to the labour-protection stickers instructions.
B) All the labour-protection stickers instructions apply to other users as well.
C) In case of damaging or destroying a LABOUR-PROTECTION STICKER located on the machine,
operators are obliged to REPLACE IT OR PROVIDE THE MACHINE WITH A NEW ONE IMMEDIATELY.
The position, design and exact meaning of the labour-protection stickers located on the machine are given in
the following table (Tab. 2) and in Figure (Fig.1).
Table 2 - The Labour-protection stickers located on the machine
WARNING SAFETY LABELS
TEXT TO THE LABELS
POSITION ON THE MACHINE
Before handling the machine,
carefully read the operating manual.
Observe the instructions and safety
regulations for machine operation
during use.
P 1 H
Driving the machine and
transportation on its construction is
strictly forbidden.
P 37 H
When connecting or disconnecting,
do not step between the tractor and
the machine, also do not enter this
space, if the tractor and the machine
are not at rest and the engine is not
turned off.
P 2 H
Stay outside the reach of the
unsecured side frames of the
machine.
P 50 H
Stay outside the reach of the tractor
- agricultural machine set, if the
tractor engine is in operation.
P 6 H

Manual
KOMPAKTOMAT K1250PS | K1570PS
10 │46
When unfolding the side frames into
the transport position, do not reach
into the area of contact with the
central frame.
P 20 H
Secure the side frames against
unfolding and the axle against
sudden fall prior to the
transportation of the machine.
P 13 H
When working and transporting the
machine, maintain safe distance
from the electric appliances.
P 39 H
Secure the machine from
undesirable movement by activating
the hand brake.
P 52 H
Do not approach the rotary parts of
the machine unless they are standing
still, i.e. they are not rotating.
P 53 H
It is strictly folding and unfolding the
side frames on slopes or inclined
surfaces.
P 100 H
Lubrication of house bearings.

Manual
KOMPAKTOMAT K1250PS | K1570PS
11 │46
Fig.1 –The Labour-protection stickers located on the K 1250 PS, K 1570 PS
P37H, P53H
P1H, P2H, P6H, P39H, P50H, P52H, P100H
P20H
P20H
P37H, P53H
P37H, P53H
P37H, P53H
P37H, P53H
P37H, P53H
P20H
P20H
P20H
P20H

Manual
KOMPAKTOMAT K1250PS | K1570PS
12 │46
1. MACHINE DESCRIPTION
The machine has been designed as semi-mounted and folding. The basic version of the machine includes a
chassis and drawn working sections. The machine is structurally designed so that the transport width is up to 3
m and the transport height is up to 3.5 m.
The chassis with the drawn appliance aggregates with a height-adjustable hole for a tractive bolt with 50
mm. The chassis includes a supporting leg that supports the machine when it is disconnected from the tractor
and there are two firm delayed axles, out of which one is equipped with an automatic parking brake function.
Furthermore, the chassis includes hydraulically controlled catches securing the side frames in the transport
position. The chassis also includes automatically spring-loaded trail cultivators.
The working section is attached to the chassis by swinging segments that allow continuous height tracing of the
field behind the tractor and chassis. Furthermore, the working section is connected to the chassis by main
piston rods and tractive ropes that transfer the tractive force from the tractor to the machine during the work
in the field. The working section of the machine consists of a massive spring-loaded, height-adjustable variable
leveller, crumbling front rollers, height-adjustable ploughshare section with a leveller and compactors with a
rear leveller. Furthermore, the working section includes auxiliary wheels that are used for unfolding the
machine into the working position or folding it into the transport position.
Fig. 2 - Machine Description K 1250 PS - K 1570 PS
1.1 Aggregation to a tractor
HITCH VERSION –K80; C40; C50; C70
Aggregation of the machine to the fixed bottom hitch with a K80
ball or with a pulling loop with the diameter of 40mm, 50mm or
70mm.
1.2 Working parts
TRACK CULTIVATOR
CA –Track Cultivator with Sweep
Automatically released tractor track cultivator with a sweep. Suitable for loose
types of soil where there is no risk of formation of wet clods. Possibility of
mechanical depth setting up to 80mm. Possibility of setting the position directly
behind the tractor wheels.
CC –Track Cultivator with Chisel Share
Automatically released tractor track cultivator with a chisel share. Suitable for
heavier types of soil where there is no risk of formation of wet clods. Possibility
of mechanical depth setting up to 80mm. Possibility of setting the position
directly behind the tractor.
CHASSIS
WORKING
SECTION

Manual
KOMPAKTOMAT K1250PS | K1570PS
13 │46
FRONT LEVELLERS
FL - FH–Front Fixed Serrated Levelling Bar
Automatically released levelling bar with a serrated section. Massive
construction for precise levelling of coarse furrows.
Possibility to adjust the height of the leveller; the leveller spring
preloading may be changed.
You can choose either manual adjustment of the leveller height or
hydraulically controlled leveller height.
FRONT WORKING ROLLERS
SB –Spiral Bar Roller - 40 cm - 60 kg/m –9 bars
Quality clod crumbling.
Suitable for humid conditions.
This type of roller can be used as the FRONT or REAR roller.
BR - Bar Roller - 40 cm - 60 kg/m –12 bars
Very good quality clod crumbling.
Not suitable for humid conditions.
This type of roller can be used as the FRONT or REAR roller.
RR –Ring Roller 40 cm - 115 kg/m
Quality work in all types of soil.
Good depth guiding.
Suitable for more humid soils.
This type of roller can be used as the FRONT or REAR roller.
BR
SB
RR
Crumbling
●●●○
●●●○
●●○○
Compacting
●●●○
●●●○
●●●●
Depth guiding
●●●●
●●●●
●●●●
Resistance to clogging
●●○○
●●●○
●●●●
Suitable for rocky soils
●●●○
●●●○
●●●○
Suitable for wet soils
●○○○
●●●○
●●●●
Heavy soils
●●○○
●●○○
●●●○
Medium soils
●●●○
●●●○
●●●○
Light soils
●●●●
●●●●
●●●○
● –MAX / ○ - MIN

Manual
KOMPAKTOMAT K1250PS | K1570PS
14 │46
SHARE SECTIONS
AL –Section of shares with sweeps in two rows
The share section is equipped with sweeps with the width of 25 cm
in two rows. Each sweep is protected by a leaf spring. This section is
suitable for lighter soil conditions without plant residues. There is a
leveller behind the sweeps.
CF –Section of chisel shares in four rows
The share section is equipped with slim chisels with the width of 7
cm in four rows. The section is suitable for processing soil in spring
when it is not suitable to pull wet soil out to the surface, or for
heavy soils. There is no leveller behind the chisels.
AP –Section of shares with sweeps in two rows
A universal share section is equipped with sweeps with the width of
25 cm in two rows. The sweeps are mounted to frames with
geometry improving the permeability of plant residues. Therefore,
this section is suitable for land with a higher occurrence of crushed
plant residues as well as for heavy soils. There is a leveller behind
the sweeps.
AL
CF
AP
Number of rows of shares (pieces) / Row
spacing (mm)
2 / 400
4 / 240
2 / 490
Leveller behind shares
●●●●
○○○○
●●●●
All-area processing
●●●●
●●●○
●●●●
Suitable for light soils
●●●●
●●●●
●●●●
Suitable for medium soils
●●●○
●●●○
●●●●
Suitable for heavy soils
●●●○
●●●○
●●●●
Suitable for rocky soils
●●●○
●●●○
●●●●
Suitable for wet soils
●●○○
●●●●
●●○○
Resistance to clogging
●●○○
●●●○
●●●○
● –MAX / ○ - MIN
LEVELLING BARS BEHIND SHARES
LEVELLING BAR BEHIND SHARES
The bar can be used behind all types of share sections. The bar is sued for
spreading the loosened soil before the rear roller. The height adjustment
is performed using a chain, which the bar is suspended from.

Manual
KOMPAKTOMAT K1250PS | K1570PS
15 │46
REAR WORKING ROLLERS
SB –Spiral Bar Roller - 40 cm - 60 kg/m –9 bars
Quality clod crumbling.
Suitable for humid conditions.
This type of roller can be used as the FRONT or REAR roller.
BR - Bar Roller - 40 cm - 60 kg/m –12 bars
Very good quality clod crumbling.
Not suitable for humid conditions.
This type of roller can be used as the FRONT or REAR roller.
RR –Ring Roller 40 cm - 115 kg/m
Quality work in all types of soil.
Good depth guiding.
Suitable for more humid soils.
This type of roller can be used as the FRONT or REAR roller.
CR –Cross-kill Roller with Cleaner - 40 cm - 170 kg/m
Quality clod crumbling and backwards compaction.
Excellent work in light, medium and heavy soils.
Not suitable for more humid soils.
Not suitable for soils with a large quantity of rocks.
This type of roller can be used as the REAR roller only.
DCR –Double-row Cross-kill Roller - 40 cm / 40 cm - 175 kg/m
Quality clod crumbling and backwards compaction.
Mixes the processed soil more intensely.
Excellent work in light, medium and heavy soils.
Can work in slightly moist conditions.
Not suitable for rocky soils.
This type of roller can be used as the REAR roller only.
BR
SB
CR
DCR
RR
Crumbling
●●●○
●●●○
●●●●
●●●○
●●○○
Compacting
●●●○
●●●○
●●●●
●●●○
●●●●
Depth guiding
●●●●
●●●●
●○○○
●●○○
●●●●
Resistance to clogging
●●○○
●●●○
●●●○
●●●●
●●●●
Suitable for rocky soils
●●●○
●●●○
●●○○
●○○○
●●●○
Suitable for wet soils
●○○○
●●●○
●●○○
●●●○
●●●●
Heavy soils
●●○○
●●○○
●●●○
●●●○
●●●○
Medium soils
●●●○
●●●○
●●●●
●●●●
●●●○
Light soils
●●●●
●●●●
●●●●
●●●●
●●●○
● –MAX / ○ - MIN

Manual
KOMPAKTOMAT K1250PS | K1570PS
16 │46
FINISHING OPERATIONS
LF - REAR FINISHING LEVELLING BAR
The levelling bar behind the rear roller levels and evenly
spreads the loosened soil. Possibility to change the angle of
the leveller using backstop plates  thus increasing the
efficiency of the leveller.
SUPPORT END STOPS OF THE FINISH LEVELLER
The end stops are used for the optional change in the finish
leveller angle. When needed, it may improve the work of
the leveller and the quality of the cultivated soil.
RF - REAR FINISHING ROLLER Ø220mm
The finishing roller actively disintegrates any remaining
clods behind the rear roller. Possibility to change the
preloading of the draw spring tension  thus increasing
the efficiency of the finishing roller.
!!Be careful –the finishing roller cannot be used behind the
two-row cross-kill rollers.
2. SPECIFICATIONS
Table 3 - Specifications
PARAMETERS
K 1250 PS
K 1570 PS
Operating width (mm)
12500
15700
Transport width (mm)
3000
Transport height (mm)
3500
Transport lenght of the machine (mm)
9550
Working lenght of the machine (mm)
11550
Working depth (mm)
0-100
Number of shares
53
67
Working performance (ha/hour)
10-15
12,4-18,5
Working speed (km/hour)
8-12
Towing means (kW)
243
316
Maximum transport speed (km/hour)
25
Maximum slope accessibility (°)
6
Tyre dimensions (type)
19.0/45-17 14PR
Tyre pressure (kPa)
400
Weight of the machine (ver.II)
10500
12500

Manual
KOMPAKTOMAT K1250PS | K1570PS
17 │46
3. OPERATIONAL SAFETY RULES
Before you take over the machine, please check that is has not been damaged during transportation and
that all its parts have been supplied according to the delivery note.
Before setting the machine to work, please read these Operating manual carefully.
Before starting to work, please acquaint yourself with the overall functioning of the machine and its
controls.
Please observe not only the rules of these Manual but also general labour-protection, fire-protection
and environment-protection regulations as well as transportation safety rules.
The machine may only be operated by a person, which meets requirements of the item A.3 above.
Before setting the machine to work, please check its condition. In case of showing any signs of
damaging, the machine must not be operated.
When aggregating the machine with the tractor, follow the Instruction given in Chapter E/Page 5 to 6.
Execute aggregation of the machine with the tractor on an even and compact surface.
Before uncoupling the tractor and the machine in the transport position, the machine must be secured
against accidental and undesirable unfolding, i.e. the folded lateral frames must be locked by the
connecting bar.
When working on slopes, observe the slope accessibility of the whole TRACTOR-MACHINE set.
It is strictly forbidden to unfold or fold the machine on slopes –see the P100H labour-protection (safety)
sticker located on the machine.
Before starting up the tractor, check that there is no unauthorized person within the operating reach of
the set and sound the horn.
Operators should pay attention to any person's not approaching the machine during operation in the
field.
It is forbidden to dismantle the parts of the machine hydraulic system that are under pressure.
Hydraulic oil penetrating the skin under high pressure causes serious injuries. Should this happens, call
the doctor immediately.
4. ROAD TRANSPORT RULES
The transport speed of the tractor with the machine should not exceed 25 km p.h.
When transporting the machine on public roads, follow the instruction given in Chapter G/Page 6.
When transporting the machine on roads, the operator(s) should observe the applicable law and
regulations including those which specify the tractor axle load depending on the transport speed.
When transporting the machine on ground communications, the side frames must be secured by the
connecting rod and the machine must be fitted with safety shields with a functional light set.
Considering the size of the machine, the operator transporting the machine must be very careful and
considerate to other road users.

Manual
KOMPAKTOMAT K1250PS | K1570PS
18 │46
Checking the nuts on the transport axle
Use the plastic arrow “Check Point” to check for loose nuts. It promptly shows the condition of the
nuts, whether they are loose or not.
Always check the Check Points before driving.
When the arrows are not facing one another, the nuts have to be tightened to the required torque and
the Check Point arrows have to point against one another as shown in the green picture.
Torque for the axle nuts:
M18x1,5 - 265Nm
M20x1,5 - 343Nm
M22x1,5 - 440Nm
5. SETTING TO WORK
When aggregating the machine with the tractor and setting it to work, the steps given in Chapter E, F
/Page 5 to 6 should be followed.
Aggregate the machine with a tractor with the use of the bottom hitch with a 50 mm or 70 mm
bolt or with K80 tow ball.
Place the trail cultivators on the chassis so that they cultivate the compacted layer of soil made by the
tyres of the chassis and the tractor. The range of the position of cultivators may be selected even for
tractors with a pair assembly, i.e. up to the width of 3.9 m. The maximal recess of cultivators is 60 mm
below the level of the tractor wheel trail.
To interconnect the hydraulic systems, use the quick-couplers of the identical model (the socket on the
machine and the plug on the tractor) - the machine is normally provided with the ISO 12.5 quick
couplers.
Always fold and unfold the machines on a flat surface. Or meet the requirement of the P100H safety
label (see p. 10).
Attach the hoses of the individual hydraulic circuits to the tractor in the order in which the hoses are
labelled. The hydraulic circuits are designated with coloured rings (see Fig. 4).

Manual
KOMPAKTOMAT K1250PS | K1570PS
19 │46
Hydraulic of the machine
Parts of the hydraulic system of the machine, which are under pressure, are forbidden to disassemble.
Hydraulic oil that penetrates the skin under high pressure causes severe injuries. In case of injury, seek a
physician immediately.
Connect the hydraulics only when the hydraulic circuits of the machine and the tractor (aggregate) are in
a pressure-less condition.
The hydraulic system is under high pressure. Regularly check for leaks and immediately remove obvious
damage of all lines, hoses, and pipe unions.
When seeking and removing leaks, use only the suitable tools.
For connecting the hydraulic system of the machine to the tractor, use the plug (on the machine) and
the socket (on the tractor) of the quick-couplers of the same type.
For simplification, the hydraulic circuits are marked by different colours.
Fig.4-designation of the hydraulic circuits
CIRCUIT A –the circuit for folding and unfolding side frames. Hydraulic circuit designated with RED rings. This
hydraulic circuit must always be turned on when working in the field.
DRAWING-OUT PISTON = UNFOLDING INTO THE WORKING POSITION
The side frames are unfolded into the working position when this circuit branch is pressurised.
PISTON RETRACTION = FOLDING INTO THE TRANSPORT POSITION
The side frames are folded into the transport position when this circuit branch is pressurised

Manual
KOMPAKTOMAT K1250PS | K1570PS
20 │46
CIRCUIT B –the circuit for the control of transportation bolts together with auxiliary wheels. Hydraulic circuit
designated with WHITE rings. This hydraulic circuit does not need to be turned on when working in the field.
DRAWING-OUT PISTON = FOLDING INTO THE TRANSPORT POSITION
By pressurising this circuit branch, the bolts lift the side frames into the transport position and the
auxiliary wheels are folded to the frames into the transport position when the side frames have been
lifted.
PISTON RETRACTION = UNFOLDING INTO THE WORKING POSITION
By pressurising this circuit branch, the auxiliary wheels are unfolded from the frames. Once unfolded,
the bolts start to open and lower the side frames.
CIRCUIT C –the circuit for the control of the supporting leg of the chassis. Hydraulic circuit designated by
BLACK rings. This hydraulic circuit does not need to be turned on when working in the field.
DRAWING-OUT PISTON = SETTING THE TRANSPORT POSITION
The supporting leg stands on the ground when this circuit branch is pressurised.
PISTON RETRACTION = SETTING THE WORKING POSITION
The supporting leg is lifted from the ground when this circuit branch is pressurised.
CIRCUIT E –the circuit for controlling the position of the track cultivators behind the chassis wheels. Hydraulic
circuit designated by MULTI-COLOUR rings. This hydraulic circuit must always be turned on when working in
the field.
Attention! Do not manipulate with this circuit when the machine is standing on hard surface (asphalt,
concrete) as it could damage the track cultivators or the surface.
DRAWING-OUT PISTON = SETTING THE WORKING POSITION
Hydraulic circuit designated by a YELLOW + GREEN ring. The track cultivators are set into the working
position when this circuit branch is pressurised.
PISTON RETRACTION = SETTING THE TRANSPORT POSITION
Hydraulic circuit designated by a RED + BLUE ring. The track cultivators are set into the transport
position when this circuit branch is pressurised.
CIRCUIT D –the circuit for folding and unfolding the external 1.5m side frames. Hydraulic circuit designated by
YELLOW rings. This hydraulic circuit is only installed in K1570PS.
This hydraulic circuit does not need to be turned on when working in the field.
UNFOLDING SIDE 1.5m FRAMES INTO THE WORKING POSITION
The external side frames are open into the working position when this circuit branch is pressurised.
FOLDING SIDE 1.5m FRAMES INTO THE TRANSPORT POSITION
The external side frames are open into the transport position when this circuit branch is pressurised.
OPTIONAL EQUIPMENT OF THE MACHINE
HYDRAULIC CIRCUIT FOR FRONT LEVELLER POSITION
CONTROL
- ONE BLUE RING
Pressurizing this branch of the circuit brings the leveller up
from the surface.
Flow limiters
reducing the speed
of the piston-rod
operation are used
in the circuit.
The precise position
can be found in the
Spare Parts
Catalogue.
HYDRAULIC CIRCUIT FOR FRONT LEVELLER POSITION
CONTROL
- TWO BLUE RINGS
Pressurizing this branch of the circuit recesses the leveller
to the surface.
HYDRAULIC CIRCUIT FOR SHARE WORKING DEPTH
CONTROL
- ONE GREEN RING
Pressurizing this branch of the circuit brings shares out of
the processed profile.
HYDRAULIC CIRCUIT FOR SHARE WORKING DEPTH
CONTROL
- TWO GREEN RINGS
Pressurizing this branch of the circuit recesses shares into
the processed profile.