FAS DS Series User manual

--
lliti
Magnetic Lock Wiring Instructions
fatt Ac.e .. 11 Security Corp.
A.12VDC Input:
Required power 0.5 amp (Maximum).
Connect the ground( -) lead from a 12VDC power source to terminal 2.
Connect the positive( +) lead from a 12VDC power source to terminal 1.
Checkjumperfor 12VDC operation.
B.24VDC input:
Require power 0.25 amp (Maximum).
Connect the ground(-) lead from a 24VDC power source in terminal2.
Connect the positive(+) lead from a 24VDC power source to terrninal1.
Check jumper for 24 VDC operation.
C.Contacts:
Reed switch dry contacts are rated max 3W(max switching contact 0.2SA) at 30VDC/AC for safe
operation. Do not exceed this rating.
If you require a normally open switch,connect the wires from the system to terminal4 and terminal 3.
If you require a normally closed switch,connect the wires from the system to terminal4 and terminalS.
Important!
1. The product should only be powered by a LlL listed power supply.
2. If power switch is not wired between DC source voltage and magnet .it will take a longer time to
de-energize the magnet simulating residual magnetism.(see below)
/~~, ~~
/ ::,,, c-. -..J", s: -~- ~=
,
,
,
OR
24V
------------------------
Correct Incorrect
Printed Circuit Board Schematic
o~ 0
-G 0 " --- -- Mag Bond Sensor
Timer 0- 90 sec
ED
0 S2 ~ I ~ I C]IO:e.;-~ III------------
L. .
pOwJe~mSpe~~ctor
o - 0
1881
- ---------------------- [j]] ~
~ ~ c ~ ~ ~~ ~~~ 2" , m
,
,
POWER SUPPLY =====----.J
,
Magnet
Dry Contact
WG001-F

Instructions For Magnetic Locking Devices
Important :Please Read Before Attempting To Install Magnetic Lock
A. Handle the equipment with care, damaging the mating surfaces of the magnet or
armature plate may reduce locking efficiency.
B. The magnet mounts rigidly to the door frame. The armature plate mounts to the
door with hardware. Kit provided that allows it to pivot about its center to com-
pensate for door wear and misalignment.
C. Template use must take place with the door in its normally closed position.
D.Before installing,please add the threadlockerto all screws. Firmly tighten the screws to Avoid
fastening loosen.
Typical Insta"ation:
DOOR FRAME
DOOR FRAME
DOOR FRAME
Plate
II..!::::=::;:=~~~ Stringer Door
L---Armature
I
Mou nti ng
-Magnet
-Magnet
Magnet
'----Armature Plate
Plate
LArmature Plate
Armature Plate Mounts To The Door
r-----Door
Nut
~Spacer
Armature Plate
I-::=waSher
Id
~/ Door
~c::::::6-
'::t.-, -:.,..----=:--Hole For Guide Pin
-=----.::.....,."::--:::;::o~~- Hole For Nut
1.0i!~=--~~;:-:::'---+-- Rub be
r Washer
~Illi~;;:..--<"------i- Steel Washer
----+-Armature Plate
35mm
'---------- Guide Pin
**Important: Fix the armature plate not too tightly, and make the rubber washer more flexible, in order
to make the armature plate automatically adjust its proper position with the magnet.

OS Series Magnetic Lock Wiring Instructions
Connect the positive (+) lead from the power source to BLACK wire
of the DOOR STATUS SENSOR.
Connect the negative (-) lead from the power source to one end of
the LIGHT, BUZZER ... for door status.
Connect the GREEN wire of the DOOR STATUS SENSOR to one end
of the LIGHT, BUZZER ... for door status.
Reed switch dry contacts are rated 0.5 Amp at 30VDC/AC for safe operation, do not
exceed this rating.
DOOR STATUS SENSOR
.- -
I NO I
Green
LIGHT
I I I
t
+
-
BLACK
ICOM
L i
I
REED SWITCH i
-~-----
.- -- -
--
RUZZER
SW
~
I
--
.....,.
ON I PCB I I
2
R
---
--
-
MAGNETIC LOCI<:
I
*'Nne"'! ~SW· is O!=~ "'"1e C::::" S:a::....5
Sensor(REED S'~\·'T':':':...; ::e:ec: t
door IS wei· c!osec
Door Sensor (Reed SW )
~o GREEN
C NO
For 2 wires
Door Sensor (Reed SW. )
NC RED
~
C
0_---
NO GREEN
For 3 wires
Armature Plate Mounts To The Door
Spacer
Nut,
Door sensor detector \
L-- _______ Guide Pin
Door
r--::= Washer
I ~ Armature Plate
**Important: Do not Fix the armature plate too tightly, and allow rubber washer more flexibility
to let armature plate adjust automatically into position with the magnet
WG-D I