FDS FD70ARM User manual

Document Number:
MAN –FD70ARM
Rev:
G
Revision Date:
05/22/2017
Page 1 of 13
©2017 FDS Avionics Corp.
All Rights Reserved.
TECHNICAL SUPPORT
470-239-7421 or FDSAvionics.com
Installation and Operation Manual
FD70ARM
7” Widescreen LED on Arm

Document Number:
MAN –FD70ARM
Rev:
G
Revision Date:
05/22/2017
Page 2 of 13
©2017 FDS Avionics Corp.
All Rights Reserved.
TECHNICAL SUPPORT
470-239-7421 or FDSAvionics.com
Table of Contents
General Information............................................................................................3
Front View............................................................................................................3
Additional Information........................................................................................3
Specifications......................................................................................................4
Installation Instructions......................................................................................4
Power...................................................................................................................4
Wiring Suggestions ............................................................................................5
VGA Wiring..........................................................................................................5
Mounting and Base Information ........................................................................6
Power and Ground Wiring..................................................................................6
Power/Video ........................................................................................................7
Operation Instructions .......................................................................................8
Monitor Control Buttons.....................................................................................8
Remote Control Buttons.....................................................................................9
Technical Drawing ............................................................................................10
Technical Support.............................................................................................11
Instructions for Continued Airworthiness......................................................11
Warranty ............................................................................................................12
Log of Revisions...............................................................................................13

Document Number:
MAN –FD70ARM
Rev:
G
Revision Date:
05/22/2017
Page 3 of 13
©2017 FDS Avionics Corp.
All Rights Reserved.
TECHNICAL SUPPORT
470-239-7421 or FDSAvionics.com
General Information
The FD70ARM is a 7” Widescreen LED on a pivoting, rotating Arm. Built with retrofit
aircraft integration in mind, this display can switch between three video input sources
using the buttons on the bezel or the Infrared Remote.
The arm has both a hinge and a pivot point, and it can rotate 180° around the attach point
at the base and 180° at the bottom of the center of the LED. This mount will allow the
monitor to tilt back away from the passenger up to 15°.
Front View
Additional Information
The FD70ARM is made of all metal components. The milled aluminium arm represents
the evolution of several design enhancements for an optimum removable mounting
solution.
The 7” Widescreen LED utilizes a state of the art digital video decoding chipset for the
analog video input. The three video sources in order of picture quality are VGA (computer
graphics, like Moving Maps), and two Composite Video (DVD, Camera or VCR). Both
NTSC and PAL formats are auto-detected.
The FD70ARM can also be connected to existing video switchers and can take a
composite video input from a selector interface box. In this case, multiple input sources
can be selected and displayed on the monitor.

Document Number:
MAN –FD70ARM
Rev:
G
Revision Date:
05/22/2017
Page 4 of 13
©2017 FDS Avionics Corp.
All Rights Reserved.
TECHNICAL SUPPORT
470-239-7421 or FDSAvionics.com
Specifications
Display Type
7” TFT Color LCD (LED backlight)
Aspect Ratio
16:9
Screen Resolution
800x480 pixels
Maximum Supported Resolution
1600x1200 pixels
Brightness
500 cd/m2
Contrast
400:1
Video Sources
1x VGA, 2x Composite
Composite Video Type Supported
PAL/NTSC
Power Consumption
12V DC @ 0.80 AMPS,
28V DC @ 0.40 AMPS
Monitor Overall Size
7.72”(W) x 4.88”(H) x 1.42”(D)
Viewable Area
6.00”(W) x 3.60”(H)
Enclosure Materials
Plastic/Aluminum
Weight with Base
2.31 lbs
Certifications
DO-160 Sec. 7 Cat. B, PMA Approved
Installation Instructions
All cabin entertainment equipment, such as the FD70ARM, should be installed on a non-
essential bus and have a dedicated circuit breaker. It is a requirement that a switch be
installed in the cockpit so that the pilot can de-energize the entertainment system should it
become necessary.
It is recommended that you leave approximately ¼ inch of space around the rear of the
display to have circulating air.
Power
This is a 28V DC monitor that requires .4 AMPS of power to operate.

Document Number:
MAN –FD70ARM
Rev:
G
Revision Date:
05/22/2017
Page 5 of 13
©2017 FDS Avionics Corp.
All Rights Reserved.
TECHNICAL SUPPORT
470-239-7421 or FDSAvionics.com
Wiring Suggestions
All shields should be grounded to the connector at the source, and floating at the display.
Avoid routing video wiring parallel to:
AC wiring
Strobe wiring
DC motor supply cables
Inverter cabling
Or any other potential noise source.
VGA Wiring
Recommended cable for VGA purpose is ECS P/N 453005. This is a single shielded
cable containing 5 separate coaxial cables, color-coded to match the functions of the
wires.
The individual wires should be extended with 6” 22awg wires using an environmental
splice for the red & green wires, and Raychem caps for the blue, white, and black wires.

Document Number:
MAN –FD70ARM
Rev:
G
Revision Date:
05/22/2017
Page 6 of 13
©2017 FDS Avionics Corp.
All Rights Reserved.
TECHNICAL SUPPORT
470-239-7421 or FDSAvionics.com
Mounting and Base Information
The FD70ARM mates with a drink rail mount, FDBASE (left), or a wall mount, FDBASE-W
(right).
The connector seats deeply in the mount and is held in place by either gravity or a locking
pin. The secure High Density DB15 pin and connector can only be connected one
direction. The mount is keyed to prevent inadvertent misalignment.
Power and Ground Wiring
22 AWG wire is recommended for Power and Ground applications.

Document Number:
MAN –FD70ARM
Rev:
G
Revision Date:
05/22/2017
Page 7 of 13
©2017 FDS Avionics Corp.
All Rights Reserved.
TECHNICAL SUPPORT
470-239-7421 or FDSAvionics.com
Power/Video
Pin out for (High Density DB-15 inset in the bottom of the arm)
This male DB-15 has Power, Composite Video #1, Composite Video #2 and VGA
connections.
Part Numbers for DB-15 connectors, manufactured by Tyco or Amp.
High density, D-sub, 15 contact receptacle (female) P/N 748565-1
HD15F pins P/N M39029/57-354
Pin
Number
Description
1
28V DC Power
2
28V DC Ground
3
N/C
4
Composite Video #1 - Signal
5
Composite Video #1 - Shield
6
N/C
7
Composite Video #2 –Signal
8
Composite Video #2 - Shield
9
Red Video (Pin 1 on Standard VGA)
10
Green Video (Pin 2 on Standard VGA)
11
Blue Video (Pin 3 on Standard VGA)
12
Red Ground (Pin 6 on Standard VGA)
13
Green Ground (Pin 7 on Standard VGA)
14
Horizontal Sync (Pin 13 on Standard
VGA)
15
Vertical Sync (Pin 14 on Standard VGA)

Document Number:
MAN –FD70ARM
Rev:
G
Revision Date:
05/22/2017
Page 8 of 13
©2017 FDS Avionics Corp.
All Rights Reserved.
TECHNICAL SUPPORT
470-239-7421 or FDSAvionics.com
Operation Instructions
The FD70ARM is continuously on but can be de-energized by removing power from the
entertainment system. No pilot or aircrew action is necessary during flight or ground
operation.
The passengers will be able to change the video output from the FD70ARM using the
video source select switch on the LED monitor, or remotely throughout the cabin with the
included IR remote. Point the IR remote at the top of the LED to make changes.
When applying power, the display will turn on and look for a valid input on the last known
source. If no input is found, the display will go to standby mode. Pressing the Input Select
button (S) will select a new video input.
Monitor Control Buttons
Located at the bottom of the FD70ARM LED are five buttons and one status LED.
Operations are as follows:
BUTTON
FUNCTION
DESCRIPTION

Adjust UP
Incremental adjustment or Menu selection

Adjust DOWN
Incremental adjustment or Menu selection
S
INPUT
SELECT
Press and select between VGA, Composite #1
and Composite #2.
M
MENU
Pressing this will activate the Menu.

Status Light
Green –on and operating; None –Off or standby
Light Sensor
Senses level of outside lighting
POWER
On/Off

Document Number:
MAN –FD70ARM
Rev:
G
Revision Date:
05/22/2017
Page 9 of 13
©2017 FDS Avionics Corp.
All Rights Reserved.
TECHNICAL SUPPORT
470-239-7421 or FDSAvionics.com
Remote Control Buttons
See “Button Controls” above for Remote Control Button functions.
Power
Menu
Source

Document Number:
MAN –FD70ARM
Rev:
G
Revision Date:
05/22/2017
Page 10 of 13
©2017 FDS Avionics Corp.
All Rights Reserved.
TECHNICAL SUPPORT
470-239-7421 or FDSAvionics.com
Technical Drawing