Federal Signal Corporation SmartSiren Platinum Series Mounting instructions

Control Pad Conguration
Software Manual
2562418C
REV. C 411
Printed in U.S.A.

Arjent®, Legend®, Raydian®,SmartSiren®, Solaris®, Impaxx®, and Viper®are registered trademarks of Federal Signal Corp.
Convergence is a trademark of Federal Signal Corporation.
Pentium®is a registered trademark of Intel Corporation.
Windows®is a registered trademark of Microsoft Corporation in the United States and other countries.
InstallShield is a registered trademark and/or service mark of InstallShield Corporation.

3SmartSiren Platinum Series
Table of Contents
CHAPTER 1 Safety Messages .....................................................................7
Safety Messages to Users of This Software ............................................................................7
Safety Messages to Installers of Federal Signal Electronic Sirens and Sound/Light Systems ..........7
CHAPTER 2 Preparing to Program the Control Pad ..................................10
System Requirements.......................................................................................................10
Installing the Software......................................................................................................11
Connecting the Control Pad to Your Computer in Windows XP.................................................12
Connecting the Control Pad to Your Computer in Windows Vista/7........................................... 16
CHAPTER 3 Exploring the Interface......................................................... 21
An Overview of the SmartSiren Platinum Conguration Software ............................................ 21
Application Header ...........................................................................................................23
Minimize Window (–) Button and Close Program (X) Buttons..................................................23
Connection Status Pane ....................................................................................................23
The Four Programming Modules .........................................................................................24
The Button Conguration Module ................................................................................... 24
The Button Selection Module ......................................................................................... 25
SignalMaster and Warn Buttons .................................................................................25
Slide Switch Buttons................................................................................................. 26
The Device Selection Module .........................................................................................26
Device Selection Tabs ...............................................................................................27
Option Buttons and Checkboxes................................................................................. 27
Drop-Down Lists ......................................................................................................27
Escape Button .........................................................................................................28
The Button Control Module............................................................................................28
Inputs 1 to 4 ...................................................................................................................29
Horn Ring .......................................................................................................................30
File Transfer Status Panes .................................................................................................30
Uploading Conguration Files ........................................................................................30
Downloading Conguration Files ....................................................................................30
CHAPTER 4 Conguring the Lightbar....................................................... 34
An Overview of the Lightbar Pane.......................................................................................34
Lightbar Default Settings...................................................................................................35
Assigning Lightbar Functions to Buttons ..............................................................................35
Linking Buttons to Slide Switch Positions (Lightbar Pane)....................................................... 39
CHAPTER 5 Conguring the SignalMaster................................................ 44
An Overview of the SignalMaster Pane ................................................................................ 44
SignalMaster Default Settings ............................................................................................45
Assigning SignalMaster Control to the SignalMaster Button .................................................... 46

Table of Contents
4SmartSiren Platinum Series
Assigning SignalMaster Control to the Warn Button ...............................................................48
Assigning SignalMaster Control to Buttons 1 to 15 and Inputs ................................................51
Assigning SignalMaster Control to the Slide Switch ............................................................... 54
CHAPTER 6 Conguring the Siren............................................................ 59
An Overview of the Siren Pane ........................................................................................... 59
Siren Default Settings.......................................................................................................60
Siren Functions for Buttons 1–15 .......................................................................................60
Siren Functions for Slide Switch 1–3 ................................................................................... 63
Siren Input Control for Inputs 1–4......................................................................................66
CHAPTER 7 Conguring the Internal Relays ............................................ 71
An Overview of the Internal Relays..................................................................................... 71
Relay Default Settings ......................................................................................................72
Conguring the Internal Relays (Buttons 1 to 15 and Inputs) .................................................72
Conguring the Internal Relays for the Slide Switch Buttons .................................................. 76
CHAPTER 8 Conguring the External Relay ............................................. 81
An Overview of the External Relay......................................................................................81
Conguring the External Relay ........................................................................................... 82
Conguring the External Relay for the Slide Switch Buttons ................................................... 85
CHAPTER 9 Conguring the ILS System .................................................. 89
An Overview of the ILS System ..........................................................................................89
Conguring the ILS System ...............................................................................................90
Conguring the ILS System for the Slide Switch Buttons .......................................................93
CHAPTER 10 Completing the Control Pad Conguration ..........................98
Final Steps in Completing the Conguration .........................................................................98
Saving Your Completed Conguration File............................................................................98
Printing a Record of Your Conguration File..........................................................................99
Uploading the Conguration File to the Control Pad............................................................. 101
Putting the Control Pad into Operation Mode ...................................................................... 101
Testing the SmartSiren Platinum System ........................................................................... 102
APPENDIX.............................................................................................. 103
Troubleshooting Your IP Connection in Windows XP............................................................. 103
Resetting the IP Address in Windows XP............................................................................ 105
Troubleshooting Your IP Connection in Windows Vista/7....................................................... 108
Resetting Your IP Address in Windows Vista/7 .................................................................... 110
The Default Conguration................................................................................................ 115
Button Layout Worksheet ................................................................................................ 116

Table of Contents
5SmartSiren Platinum Series
Tables of Functions
Button Control Capabilities.........................................................................................................31
Menu Commands......................................................................................................................32
Lightbar Auxiliary Functions ....................................................................................................... 42
SignalMaster Types ...................................................................................................................57
SignalMaster ILS Directional Patterns ..........................................................................................58
Fast and Low Power Options.......................................................................................................58
Siren Function (Buttons 1–15)....................................................................................................69
Siren Control (Buttons 1–15) ..................................................................................................... 69
Siren Control (Horn Ring) .......................................................................................................... 69
Siren Control (Inputs 1–4).........................................................................................................70
Siren Control (Slide Switch 1–3)................................................................................................. 70
Pins for Internal Solid State Relay...............................................................................................79
Switch Positions for Internal Solid State Relays ............................................................................79
Flash Functions for Perimeter Lights: Internal Relays .....................................................................80
Flash Functions for Perimeter Lights: External Relay .....................................................................88
ILS System Functions................................................................................................................97

6

7SmartSiren Platinum Series
CHAPTER 1
Safety Messages
Safety Messages to Users of This Software
People’s lives depend on your safe installation and usage of Federal Signal products. It is
important to read, understand, and follow all instructions shipped with the products. In
addition, listed below are some other important safety instructions and precautions you
should follow:
• The SmartSiren® Platinum enables installers to easily change the conguration and functions of
the sound and light warning systems of an emergency vehicle. To avoid conguration errors, it is
important to carefully read this manual before using this software.
To help you plan your conguration, use the worksheet is on page 116.
Failure to follow all safety precautions and instructions may result in property damage,
serious injury, or death to you or others.
Safety Messages to Installers of Federal Signal Electronic Sirens and
Sound/Light Systems
People’s lives depend on your proper installation and servicing of Federal Signal products. It
is important to read and follow all instructions shipped with this product. In addition, listed
below are some other important safety instructions and precautions you should follow:
Before Installation
Qualications
• To properly install an electronic siren you must have a good understanding of automotive electrical
procedures and systems, along with prociency in the installation and service of safety warning
equipment. Always refer to the vehicle’s service manuals when performing equipment installations on
a vehicle.
Sound Hazards
• Your hearing and the hearing of others, in or close to your emergency vehicle, could be damaged
by loud sounds. This can occur from short exposures to very loud sounds, or from longer exposures
to moderately loud sounds. For hearing conservation guidance, refer to federal, state, or local
recommendations. OSHA Standard 1910.95 offers guidance on “Permissible Noise Exposure.”

Safety Messages
8SmartSiren Platinum Series
All effective sirens and horns produce loud sounds (120 dB) that may cause permanent hearing loss.
Always minimize your exposure to siren sound and wear hearing protection. Do not sound the siren
indoors or in enclosed areas where you and others will be exposed to the sound.
• Federal Signal siren ampliers and speakers are designed to work together as a system. Combining
a siren and speaker from different manufacturers may reduce the warning effectiveness of the siren
system and may damage the components. You should verify or test your combination to make sure
the system works together properly and meets federal, state and local standards or guidelines.
During Installation
• Do NOT get metal shavings inside the product. Metal shavings in the product can cause the system
to fail. If drilling must be done near the unit, place an ESD-approved cover over the unit to prevent
metal shavings from entering the unit. Inspect the unit after mounting to be sure there are no
shavings present in or near the unit.
• Do NOT connect this system to the vehicle battery until ALL other electrical connections are made,
mounting of all components is complete, and you have veried that no shorts exist. If wiring is
shorted to vehicle frame, high current conductors can cause hazardous sparks resulting in electrical
res or ying molten metal.
• To avoid a battery explosion, always disconnect the negative battery cable rst and reconnect it last.
Avoid causing a spark when connecting near tot to the battery. The gases produced by a battery can
cause a battery explosion that could result in vehicle damage and serious injury.
• Be sure the siren amplier and speaker(s) in your installation have compatible wattage ratings.
• In order for the electronic siren to function properly, the ground connection must be made to the
NEGATIVE battery terminal.
• Sound output will be severely reduced if any objects are in front of the speaker. If maximum sound
output is required for your application, you should ensure that the front of the speaker is clear of any
obstructions.
• Install the speaker(s) as far forward on the vehicle as possible, in a location which provides maximum
signaling effectiveness and minimizes the sound reaching the vehicle’s occupants. Refer to the
National Institute of Justice Guide 500-00 for further information.
• Mounting the speakers behind the grille will reduce the sound output and warning effectiveness of
the siren system. Before mounting speakers behind the grille, make sure the vehicle operators are
trained and understand that this type of installation is less effective for warning others.
• Sound propagation and warning effectiveness will be severely reduced if the speaker is not facing
forward. Carefully follow the installation instructions and always install the speaker with the projector
facing forward.
• Do NOT install the speaker(s) or route the speaker wires where they may interfere with the operation
of airbag sensors.
• Installation of two speakers requires wiring speakers in phase.
• Never attempt to install aftermarket equipment, which connects to the vehicle wiring, without

Safety Messages
9SmartSiren Platinum Series
reviewing a vehicle wiring diagram available from the vehicle manufacturer. Insure that your
installation will not affect vehicle operation and safety functions or circuits. Always check vehicle for
proper operation after installation.
• Do NOT install equipment or route wiring or cord in the deployment path of an airbag.
• If a vehicle seat is temporarily removed, verify with the vehicle manufacturer if the seat needs to be
recalibrated for proper airbag deployment.
• Locate the control head so the vehicle, controls, and microphone can be operated safely.
• When drilling into a vehicle structure, be sure that both sides of the surface are clear of anything that
could be damaged.
After Installation
• After installation, test the siren system and light system to ensure that it is operating properly.
• Test all vehicle functions, including horn operation, vehicle safety functions and vehicle light systems,
to ensure proper operation. Ensure that the installation has not affected vehicle operation or changed
any vehicle safety function or circuit.
• After testing is complete, provide a copy of these instructions to the instructional staff and all
operating personnel.
• File these instructions in a safe place and refer to them when maintaining and/or reinstalling the
product.
Failure to follow all safety precautions and instructions may result in property damage,
serious injury, or death.
RETAIN AND REFER TO THESE MESSAGES

10 SmartSiren Platinum Series
CHAPTER 2
Preparing to Program the Control Pad
PRECAUTIONS FOR CONFIGURING THE SMARTSIREN PLATINUM CONTROL PAD
Property damage, serious injury, or death may result if the SmartSiren Platinum control
pad is improperly congured. Conguration is to be performed at the time of the software
installation. It is NOT intended for operators to “customize” the operation of the control pad
for their individual preferences. It is the installer’s responsibility to determine compatibility,
suitability, and ensure proper programming of the system. In addition, the person responsible
for programming MUST be familiar with local codes and procedures for the safe operation of
emergency-vehicle siren and lights.
System Requirements
The SmartSiren Platinum Conguration Software is supported on laptops and desktops meeting these
minimum requirements:
• 1 GHz Pentium®3 processor or compatible (32-bit and 64-bit)
• Microsoft Windows® XP with Service Pack 2, Windows Vista or Windows 7 (32-bit and 64-bit versions)
• 512 MB RAM for Windows XP
1 GB RAM for Windows Vista and Windows 7
Depending on your system, more memory may be required.
• 15 MB available disk space
• 1024 x 768-pixel monitor resolution, 16-bit display (32-bit recommended)
• CD-ROM drive
• One free RJ-45 Ethernet port for connection to the SmartSiren Platinum control pad with the included
Ethernet cable (Federal Signal part number 1751532)
This chapter explains how to install the SmartSiren Platinum Conguration Software on your computer.
It also explains how to establish an IP address between the control pad and your computer in
Windows XP, Windows Vista and Windows 7. A local area connection (LAN) is not needed because the
SmartSiren Platinum Conguration software creates a network between your computer and the control
pad. Finally, the chapter walks you through the process of setting up the control pad for programming.
To wire the control pad for 12 Vdc power, which is needed for programming, refer to the SmartSiren
Platinum Installation, Maintenance, and Service manual, document number 2562502 or the Quick
Connect Guide, document number 2562417.

Preparing to Program the Control Pad
11 SmartSiren Platinum Series
Before you begin programming the SmartSiren Platinum control pad, read this manual to understand
the programming process and decide how you want the control pad to operate. To help you plan your
conguration, a worksheet provided in the appendix on page 116. After you nish programming the
control pad, you can also print a copy of each conguration window. See “Printing a Record of Your
Conguration File” on page 99.
Installing the Software
To install the control pad conguration software:
1. Close all applications that are running on your computer.
NOTE
Uninstall the SmartSiren Platinum Conguration Software
If you have a version of the SmartSiren Platinum software installed on your
computer, uninstall the software before installing the latest version by selecting
Start > Control Panel > Add or Remove Programs > SmartSiren Platinum
3000 > Remove.
2. Insert the SmartSiren Platinum Series CD into your CD or DVD drive.
3. When the InstallShield® Wizard appears, click Next to continue. Follow the on-screen instructions
to complete the installation. If the InstallShield Wizard does not appear automatically, navigate
to the CD-ROM drive and double-click setup.exe. If you are using Windows Vista, right-click
setup. exe and choose Run as Administrator.

Preparing to Program the Control Pad
12 SmartSiren Platinum Series
4. Create and name a folder on your hard drive in which to store your conguration les.
Connecting the Control Pad to Your Computer in Windows XP
This section explains how to establish an IP address between the control pad and your computer in
Windows XP after you have installed the SmartSiren Platinum Conguration Software. The network you
create by following the steps in this section enables you to program the control pad.
1. In the Start menu click Connect to and select Open.

Preparing to Program the Control Pad
13 SmartSiren Platinum Series
2. Right-click Local Area Connection and select Properties.
3. Select Internet Protocol (TCP/IP) and click Properties.

Preparing to Program the Control Pad
14 SmartSiren Platinum Series
4. Select Obtain an IP address automatically and Obtain DNS Server Address Automatically.
Click OK.
CONTROL PAD DAMAGE
To avoid damage to the control pad, do not plug the black Federal Signal serial cable into
the computer programming port on the control pad labeled PC CONNECT ONLY.
5. Plug the connector of the orange Ethernet crossover cable into the computer programming port on
the side of the control pad.
ORANGE
ETHERNET CABLE
(P/N 751532)
PROGRAMMING
PORT ON
CONTROL PAD

Preparing to Program the Control Pad
15 SmartSiren Platinum Series
6. Plug the other end of the cable into the RJ-485 Ethernet connector on your computer.
ORANGE ETHERNET CABLE
(P/N 1751532)
ETHERNET
(RS-485) PORT
NOTE
The control pad must be connected to 12 Vdc
To establish the Ethernet connection in the next step, the control pad must be
wired for 12 Vdc power. For connection instructions, refer to the SmartSiren
Platinum Installation, Maintenance, and Service manual, document number
2562502 or the Quick Connect Guide, document number 2562417.
7. Set up the control pad for programming by putting it into Program Mode:
a) Press and hold Button 6 while powering up the control pad.
6
b) During the long beep, release Button 6.
c) Press Button 6 again. The rst LED on the control pad lights to indicate you are in
Programming Mode.

Preparing to Program the Control Pad
16 SmartSiren Platinum Series
d) Press Button 13. In approximately 30 seconds the rst LED blinks and the control pad beeps
to indicate that your Ethernet port is on.
13
If you cannot connect to the Convergence Network, refer to the troubleshooting instructions in the
appendix on page 103.
Connecting the Control Pad to Your Computer in Windows Vista/7
This section explains how to establish an IP address between the control pad and your computer in
Windows Vista and Windows 7 after you have installed the SmartSiren Platinum Conguration Software.
The network you create by following the steps in this section enables you to program the control pad.
1. In the Start menu, right-click Network and select Properties.

Preparing to Program the Control Pad
17 SmartSiren Platinum Series
2. In the Network and Sharing Center, click the link Manage Network Connections.
3. Right-click your Local Area Connection and select Properties.

Preparing to Program the Control Pad
18 SmartSiren Platinum Series
4. Select Internet Protocol Version 6 and click Properties.
5. Select Obtain an IPv6 address automatically and click OK.

Preparing to Program the Control Pad
19 SmartSiren Platinum Series
CONTROL PAD DAMAGE
To avoid damage to the control pad, do not plug the Federal Signal serial cable into
the computer programming port on the control pad labeled PC CONNECT ONLY.
6. Plug the connector of the orange Ethernet crossover cable into the computer programming port
on the side of the control pad.
ORANGE
ETHERNET CABLE
(P/N 751532)
PROGRAMMING
PORT ON
CONTROL PAD
7. Plug the other end of the cable into the RJ-485 Ethernet connector on your computer.
ORANGE ETHERNET CABLE
(P/N 1751532)
ETHERNET
(RS-485) PORT
NOTE
The control pad must be connected to 12 Vdc
To establish the Ethernet connection in the next step, the control pad must be
wired for 12 Vdc power. For connection instructions, refer to the SmartSiren
Platinum Installation, Maintenance, and Service manual, document number
2562502 or the Quick Connect Guide, document number 2562417.

Preparing to Program the Control Pad
20 SmartSiren Platinum Series
8. Set up the control pad for programming by putting it into Program Mode:
a) Press and hold Button 6 while powering up the control pad.
6
b) During the long beep, release Button 6.
c) Press Button 6 again. The rst LED on the control pad lights to indicate you are in
Programming Mode.
d) Press Button 13. In approximately 30 seconds the rst LED blinks and the control pad beeps
to indicate that the Ethernet port is on.
13
If you cannot connect to the Convergence Network, refer to the troubleshooting instructions in the
appendix on page 108.