Feelworld Master MA6P User manual

5.5" Super Lightweight On-Camera Monitor
Stabilizer Gimbal Best Partner
Guide Manual
Thank you for choosing Feelworld monitor.
Please read this manual carefully before you use.
MA6P
工艺：击凸
工艺：丝网银墨

Contents
Caring For Your MA6P Monitor
What Should Be In The Box
Product Description
Button Instruction
Port Instruction (bottom)
Port Instruction (left)
Menu Operation Instruction
Menu Function Instruction
Technical Parameters
Trouble Shooting
01
02
03
11
12
17
19
Power Input
Mount Points
Sunshade
07
08
10
04
05
06

1
CARING FOR YOUR MA6P MONITOR
• Do not attempt to disassemble the monitor. Doing so voids
warranty.
•Water damage is not covered by warranty, but taking the right
precautions when a water event occurs can sometimes preserve
unit functionality.
• Clean the screen with a high quality microber cloth only.
Never spray the screen directly with any sort of cleaning uid.
• Keep away from the heat source and avoid long exposure to
the sun.
• Do not cover the vents in case of overheating problems.
• For better product lifetime, try not to impact, crush or scratch
on the monitor.
Caring For Your MA6P Monitor

2 3
WHAT SHOULD BE IN THE BOX
What Should Be In The Box
PRODUCT DESCRIPTION
Product Description
• MA6P Monitor
• HDMI to Mini HDMI Cable
• HDMI to Micro HDMI Cable
• Tilt Arm
• Carrying bag
• Sunshade
• Manual
• Front Panel and Back Panel
DC OUT 8.4V USB UPGRADE
FW568&S55
20181206
144.0 27.5
87.0
DC OUT 8.4V USB UPGRADE
FW568&S55
20181206
144.0 27.5
87.0

4 5
PRODUCT DESCRIPTIONPRODUCT DESCRIPTION
• Port Instruction (bottom)
DC OUT 8.4V: DC power output interface, polarity as the
output power
Barrel output for powering your camera with a separately
available DC coupler via adaptor (like NP-FW50 Sony & LP-E6
Canon&DMW-BLF19 Panasonic).
: 3.5mm Earphone port output
USB UPGRADE: Firmware USB upgrade port
Function when OSD is
not displayed
Decrease the volume
Decrease or adjust value of
selected parameter
Increase the volume
Increase or adjust value of
selected parameter
MENU Display OSD Main menu Return to previous OSD menu
F1/ Custom button 1 Select next menu item
F2/ Custom button 2 Select previous menu item
F3 Custom button F3 /
Power On/Off
Button Function when OSD is displayed
• Button Instruction
DC OUT 8.4V USB UPGRADE
FW568&S55
20181206
144.0 27.5
87.0
DC OUT 8.4V USB UPGRADE
FW568&S55
20181206
144.0 27.5
87.0

6 7
PRODUCT DESCRIPTIONPRODUCT DESCRIPTION
• Power Input
(1) The rear cover of the monitor is equipped with F970 and
E6dual-purpose battery plate, which is applicable to F970
series of batteries and E6 series of batteries.
(2) Barrel (5.5mm outer, 2.1mm inner) at the left side of the
monitor, DC 7~24V Input.
Remark: Different specications of the battery have different
capability. The working time for the monitor will be different.
Higher capability (working time) will be longer. Please take off
the battery from the monitor if you don’t use the monitor in a
long time.
• Port Instruction (left)
DC OUT 8.4V USB UPGRADE
FW568&S55
20181206
144.0 27.5
87.0
HDMI IN: V1.4, HDMI signal input, up to
4K@30Hz.
HDMI OUT: V1.4, HDMI signal output, up to
4K@30Hz.
DC IN 12V: DC power input interface, polarity
as the input power .

8 9
PRODUCT DESCRIPTIONPRODUCT DESCRIPTION
• Mount Points
(1) 1/4" Screw Lock Installation
The 1/4 screw lock can be installed on the monitor (bottom,
right side).
①Fasten the 1/4" screw lock with the monitor.
②Use 2 screws to fasten the1/4" screw lock and the monitor.
(2) Tilt Arm Mounting
The monitor secures to your camera using the included Tilt Arm
via shoe mount or 1/4"-20 thread. The Tilt Arm enables 180° of
tilt for convenient monitoring at nearly any angle. A cold shoe
on the Tilt Arm lets you secure equipment (like a microphone,
LED light, or wireless receiver) that would otherwise be
displaced from the camera's accessory shoe.

10 11
PRODUCT DESCRIPTION
• Sunshade
① Velcro
③Sunshade
② Sunshade Frame
④Sunshade Application
Attach the Velcro (hook side) ①to the outside of the sunshade
frame of the monitor, open the sunshade ③, and align the
Velcro (loop side) on the inside of the sunshade with the
Velcro (hook side) ②on the monitor sunshade frame, and then
complete the sunshade installation ④.
• Press “MENU” button to enter OSD main menu, and press “ ”
or “ ” button to go through the secondary menu function.
• Then press “F1/ ” button to enter secondary menu. Press
“F1/ ” or “F2/ ” button to move cursor and select the items
in the secondary menu.
• After select the items in the secondary menu, press “ ” or
“ ” button to adjust the item parameters.
• Press “MENU” button to conrm the item adjustment and exit
the menu.
Menu Operation Instruction
After correctly connect to the power supply, the indicator will
turn (Red), press to turn on monitor power, the indicator will
be Yellow, and then input HDMI signals, the indicator will turn
Green from Yellow.
MENU FUNCTION INSTRUCTION

12 13
MENU FUNCTION INSTRUCTION
Menu Function Instruction
Image
Pic. Mode Standard, Mild, User, Dynamic
Brightness 0~100
Contrast 10~100
Saturation 0~100
Sharpness 0~100
Color Temp 6500, 9300, User
Tint 0~100
• Image
MENU FUNCTION INSTRUCTION
Setting
Language
English, 简体中文 , Español, Português,
Français, Nederlands, Deutsch, 日本語 ,
繁體中文
Aspect Ratio Just Scan, Panorama, Auto., 4:3, 16:9, P2P
No Signal White Screen, Blue Screen, Red Screen,
Green Screen, Black Screen
OSD Trans. Off, Low, Middle, High
OSD H 0~100
OSD V 0~100
OSD Time Off, 10Sec, 20Sec, 30Sec
Backlight 0~100
Power On Auto., Manual
USB Upgrade Copy the le to the U disk, connect the
USB cable, press “ ” button to conrm
Reset Press “ ” button to conrm, back to
original setting
• Setting

14 15
Zoom
Nine Grid Zoom Off, On
Zoom Off, 4X, 9X, 16X
Zoom Mode Off, Mode1, Mode2
Scan Mode Under Scan, Over Scan
• Zoom
• Function
Function
Center Marker Off, On
Safe Frames Off, 80%, 85%, 90%, 93%, 96%, 2.35:1
Nine Grid
Off, On
Image Freeze Off, On
Image Flip Off, H_V Flip, H Flip, V Flip
OSD Flip
Off, On
Function
Anamorphic Off, 1.3X, 2.0X, 2.0X MAG, User
Anamorphic nX 1.20X~2.00X
Check Field Off, Mono, Red, Green, Blue
Histogram Off, On
False Colors Off, On
Focus Assist Off, On
Peaking Color Red, Green, Blue
Over Exposure Off, On
Exposure Lever 1～100 IRE
Embedded Audio Off, On
Ratio Marker Off, 4:3, 13:9, 14:9, 15:9, 16:9, 1.85:1,
2.35:1
Mark Color Red, Green, Blue, Black, White
Mark Width 1～7
Modied Mark 0～6
MENU FUNCTION INSTRUCTION MENU FUNCTION INSTRUCTION

16 17
TECHNICAL PARAMETERS
For example: When in OSD menu “ F ” , press “F1/ ” button
to select F1, press “ ” or “ ” button to pop-up function
items and press “F1/ ” or “F2/ ” button to select one of
them, such as “Focus Assist”, and press “MENU” button to
conrm.
So when you exit OSD menu, you could press F1 directly on
the front of panel to turn on “Focus Assist” function.
Same setting for F2, F3 .
• Custom Button Setting F1~F3
★F1/ F2/F3: Center Marker, Safe Frames, Check Field, Focus
Assist, Aspect Ratio, Image Flip, Image Freeze, Histogram,
False Colors, Over Exposure, Embedded Audio, Nine Grid,
Zoom, Anamorphic.
To set the 3 shortcut custom button F1, F2, F3 on the panel.
Panel Size 5.5" IPS
Resolution 1920x1080 pixels
Dot Pitch 0.0639 (W) x 0.0213 (H) mm
Aspect Ratio 16:9
Brightness 500cd/m2
Contrast 1300:1
Viewing Angle 178° H/178° V
Backlight LED
Input HDMI
Output HDMI, DC OUT 8.4V, Barrel (5.5mm outer,
2.1mm inner)
Audio 3.5mm Stereo Headphone
Technical Parameters
MENU FUNCTION INSTRUCTION

18 19
HDMI Support Format
480i/576i/480p/576p
720p (60/59.94/50/30/29/25/24/23.98)
1080i (60/59.94/50)
1080p (60/59.94/50/30/29.97/25/24/24sF/23.98/
23.98sF)
4K UHD 3840×2160p (30/29.97/25/24/23.98 Hz)
4096×2160p (24Hz)
DCI 4K 4096×2160p (24Hz)
Input Voltage DC7~24V
Power Consumption ≦ 9W
Battery Plate F970/ LP-E6 Dual-purpose Battery Plate
Install Way 1/4-20 mount points (bottom, right)
Working Tem. - 20℃～ 55℃
Storage Tem. - 30℃～ 65℃
Unit Size 142Lx87.2Hx27.5D (mm)
Unit Weight 175g
• Only black and white or monochrome picture display:
①please check saturation, brightness & contrast adjustment.
②Please check "Check Field" is in black, white or monochrome
image or other condition.
• NO Image after put on the power
①Check if signal cable connecting is in good condition.
② Check signal cable connecting, and make sure to use the
standard adapter to connect the monitor. If power is supplied
by battery, please check if the battery is fully charged.
• No sound
① Check if Volume control do not open, press the volume
button, and try to increase the volume.
Trouble Shooting
TECHNICAL PARAMETERS TROUBLE SHOOTING

20
TROUBLE SHOOTING
■If there are still other problems, please contact with our
related technologists.
★As we are improving product features and product
performance, specications are subject to change without prior
notice.