Rosen Aviation 1060-001 User manual

Document Number 106282
Rev D
ELECTRONIC REVISION
CONTROLLED

Rosen Aviation 10.6” HD Widescreen Bulkhead Display
Document Number: 106282
Revision: D
Date: 03/20/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 2 of 30
Technical Manual, 10.6” HD Widescreen Bulkhead Display
© 2013 by Rosen Aviation, LLC
All Rights Reserved
The information contained herein is proprietary to Rosen Aviation, LLC. No part of this publication
may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any
language in any form by any means without the written authorization from Rosen Aviation, LLC,
except as allowed under copyright laws.
Disclaimer of Liability
The information contained in this document is subject to change without notice. Because we are
continuously improving and adding features to our products, Rosen Aviation, LLC reserves the right
to change specifications without prior notice. Rosen Aviation, LLC shall not be liable for technical or
editorial errors or omissions contained herein.
Rosen Aviation, LLC
1020 Owen Loop South
Eugene, OR 97402
541.342.3802
888.668.4955
Fax: [phone]
www.rosenaviation.com

Rosen Aviation 10.6” HD Widescreen Bulkhead Display
Document Number: 106282
Revision: D
Date: 03/20/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 3 of 30
Contents
1. INTRODUCTION.................................................................................................................5
1.1. System Overview..........................................................................................................5
1.1.1. Control Options................................................................................................................. 6
1.1.2. Display Connections......................................................................................................... 6
2. INSTALLATION GUIDELINES ...........................................................................................6
2.1. Mounting Configurations...............................................................................................6
2.2. Cooling and Ventilation.................................................................................................7
2.3. Electrical Requirements................................................................................................7
2.4. Video Connections........................................................................................................7
2.5. Pinout Connections.......................................................................................................7
3. INITIAL POWER UP ...........................................................................................................7
4. IR REMOTE CONTROL......................................................................................................8
5. OSD MENU OPTIONS........................................................................................................9
5.1. Exit................................................................................................................................9
5.2. User Menu..................................................................................................................10
5.2.1. Backlight......................................................................................................................... 10
5.2.2. Aspect Ratio................................................................................................................... 10
5.2.3. Scheme.......................................................................................................................... 11
5.2.4. Source............................................................................................................................ 11
5.2.5. Auto Adjust..................................................................................................................... 12
5.3. Image Adjust Menu.....................................................................................................12
5.3.1. Scheme.......................................................................................................................... 12
5.3.2. Picture-quality Controls................................................................................................... 12
5.3.3. Reset Scheme................................................................................................................ 13
5.3.4. Image Adjust Advanced (Submenu) ............................................................................... 13
5.4. Info..............................................................................................................................16
6. TECHNICIAN MENU.........................................................................................................17
6.1. Advanced Technician Submenu .................................................................................18
6.1.1. Factory Reset................................................................................................................. 18
6.1.2. Comp/RGB 1.................................................................................................................. 18
6.1.3. 3D Comb Filter ............................................................................................................... 19
6.1.4. Composite Sig (Signal)................................................................................................... 19
6.1.5. AGC (Automatic Gain Control)........................................................................................ 19
6.2. Mode Menu.................................................................................................................19
6.2.1. Power Mode ................................................................................................................... 20
6.2.2. Operation Mode.............................................................................................................. 20
6.2.3. SDI Overscan................................................................................................................. 21
6.2.4. SDI Overscan %............................................................................................................. 21
6.3. OSD Timeout..............................................................................................................21
6.4. Network ID..................................................................................................................22
6.5. Splash Screen ............................................................................................................22

Rosen Aviation 10.6” HD Widescreen Bulkhead Display
Document Number: 106282
Revision: D
Date: 03/20/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 4 of 30
6.6. Source Mode Submenu..............................................................................................22
6.6.1. Momentary Mode............................................................................................................ 23
6.6.2. Constant Mode............................................................................................................... 24
7. TECHNICAL REFERENCES AND SUPPORT.................................................................24
7.1. Troubleshooting..........................................................................................................25
7.2. Cleaning the Display...................................................................................................25
7.3. RTCA DO-160F Qualifications for Displays................................................................26
7.4. Supported Video Resolutions .....................................................................................28
7.4.1. VGA Resolutions............................................................................................................ 28
7.4.2. CVBS/Composite Resolutions ........................................................................................ 28
7.4.3. SDI Resolutions.............................................................................................................. 28
8. DEFINITIONS....................................................................................................................29
9. REVISION HISTORY ........................................................................................................30

Rosen Aviation 10.6” HD Widescreen Bulkhead Display
Document Number: 106282
Revision: D
Date: 03/20/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 5 of 30
1. INTRODUCTION
Rosen’s 10.6” bulkhead display (model 1060-001) brings stunning HD widescreen picture quality
into a small aircraft’s cabin interior.
Although you can use this display in standard analog systems, via Composite and/or VGA video
inputs, the 3G HD-SDI input allows you to use it in high definition systems and connect directly to
a Rosen Blu-ray player.
This manual describes how to install these all-in-one displays onto your aircraft. It contains
everything you need to know to wire the display and confirm that it is functioning correctly.
Note: Only trained and qualified personnel should perform installation and service.
The Outline & Installation drawing and the Technical Manual are available on the Rosen Aviation
website at www.rosenaviation.com.
From the Rosen Aviation home page, select the Products tab and browse by product category.
Please contact Technical Support at 541.342.3802 if you cannot find the documentation that you
need.
1.1. System Overview
The 1060-001 high-definition display enables viewers to watch digital video signals as well as
analog video signals in both high definition and standard resolutions.
Composite and SDI are the default video signals in Auto Detect mode. The Auto Detect mode
continually searches between Composite and SDI for a valid signal and then switches to that
input. In this mode, you remain connected to either input without having to set the source. If both
Composite and SDI are connected and active, then Composite is displayed by default.
Composite, SDI, Component, and RGB are all available in Standard Operation mode. RGB-1
and Component-1 share the VGA connector. Although there are four signal choices, you can
only select from three at any given time.
Figure 1 Single display installation
VGA
SDI
Composite
RosenView MX

Rosen Aviation 10.6” HD Widescreen Bulkhead Display
Document Number: 106282
Revision: D
Date: 03/20/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 6 of 30
1.1.1. Control Options
Although the 10.6” display does not have a built-in IR sensor, it provides 3.3V DC
@100mA output to power an external IR receiver. The IR Receiver (P/N 0500-006) and
RC5 Remote Control (P/N 0500-019) (sold separately) enables control options inputs to
adjust the on-screen display settings.
Alternatively, you can control the 10.6” display via a cabin management system using
RS-485 and/or RS-232. For a copy of the RS-232 External Controller Message Formats
(P/N 9002934) or RS485 Network Message Definitions document (P/N 9002933), please
contact Rosen Aviation Technical Support at 541.342.3802.
Note: For directions on operating the optional universal remote control, refer to the user’s
guide enclosed with the remote.
1.1.2. Display Connections
The following cable connections are available:
Optional HD15 Male VGA connector kit (P/N 0300-055)
Required Female 15-pin P1 connector kit (P/N 0300-053)
Optional 90-degree connector kit (P/N 0300-058)
Optional HD BNC Plug to BNC Jack (P/N 106221), an adapter for a standard BNC
connector running CVBS or SDI
The 10.6” display connectors exit straight down. The 90-degree connector kit
(P/N 0300-058) contains the following adapters to route the harnesses away from the
display:
Two –HD BNC Plug to BNC Jack
Two –right-angle BNC Plug to Jack
One –right-angle D-sub 15
One –right-angle HD15
2. INSTALLATION GUIDELINES
2.1. Mounting Configurations
The 10.6 display can be flush mounted to the bulkhead, or secured to a separate mounting
structure from the top and bottom, sides, or back of the unit. Installation requirements include
minimum mounting fasteners: four 8-32 screws.
minimum clearance: ¼” on the sides, top, and bottom; or ⅛” to the back of the unit; or
secure the display to an aluminum structure to act as a heat sink.
Consult the Outline and Installation drawing to assist with the installation process. Pay close
attention to the dimensions and fastener depths required when considering installation
requirements.
Touching the LCD with excessive force may leave pressure spots
that show in video display. Handle with care.

Rosen Aviation 10.6” HD Widescreen Bulkhead Display
Document Number: 106282
Revision: D
Date: 03/20/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 7 of 30
2.2. Cooling and Ventilation
The 10.6 chassis does not have vent holes for conductive cooling, nor does it require any
external forced-air cooling.
2.3. Electrical Requirements
Nominal voltage 28VDC / .66 A
Max Power Consumption: 20 W
2.4. Video Connections
The 1060-001 display uses the following connectors.
Figure 2 10.6 bulkhead display connections
2.5. Pinout Connections
There are several ways to connect the remote display system to an aircraft’s entertainment
system.
Pay close attention to the pinout descriptions on the Outline and Installation drawings to assist in
completing the wiring connections.
Note: This display is for entertainment purposes only; connect to a non-critical power bus.
3. INITIAL POWER UP
Make sure that power is turned off and perform the following steps.
1. Ensure a low impedance ground connection on the chassis from any one of the 8-32
mounting holes.
2. Connect the power supply and video source to the appropriate connectors.
3. An optional, 90-degree connector kit (P/N 0300-058) allows you to route the harness
towards the back, if desired.
4. Supply power and wait for a video signal on the screen. The default video mode is
Auto Detect and the default power mode is Auto On.
5. The display will search for a valid video signal by priority—Composite first and then
SDI. To use VGA, change the Operation Mode from Auto Detect to Standard
in the on-screen display (OSD).
Do not plug or unplug the display connector while power is
applied.
When cycling power, leave unit off for 20 seconds before restoring
power.

Rosen Aviation 10.6” HD Widescreen Bulkhead Display
Document Number: 106282
Revision: D
Date: 03/20/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 8 of 30
4. IR REMOTE CONTROL
The 10.6” displays may use an optional remote control to adjust the on-screen display (OSD)
settings. The instructions in this manual use the RC5 IR remote in describing how to navigate the
OSD. Table 1 shows the RC5 IR remote layout and the button descriptions.
Table 1 RC5 IR remote control
Note: The AUTO button works
only when an RGB source is
active. The MUTE and
VOLUME ± buttons are not
used.
How it Works
SOURCE
Switches between any enabled video inputs. Press the SOURCE
button twice to switch inputs. The first command sent will only display
the current source name in the upper-left corner of the monitor; the
second command switches the source.
POWER
Turns the display’s power on and off.
MENU
Opens the Main Menu to access other settings and fine-tune the
display’s picture quality. For details, see Section 5, OSD Menu
Options, on page 9.
EXIT
Closes the OSD and saves settings. Exit does not close control bars.
ENTER
Accepts changes to menu settings. Selects menu options, accepts
settings, and closes the control bars.
◄►▲▼
Controls the navigation in the on-screen display menus. Navigate
between the OSD menu pages, options, and change settings.
ASPECT
Changes the aspect ratio or proportions of the picture depending on
the video format. Switches between Full Screen, Pillar Box, and
Letterbox Expanded. See also Section 5.2.2,Aspect Ratio, on
page 10.
INFO
Opens the Info page on the OSD. Use INFO to verify source and
resolution values. Also quick access to open the Technician Menu.
See also Section 5.4, Info, on page 16.
AUTO
(RGB only) Performs an auto-adjust function without a menu. Forces
the display to evaluate the RGB signals and ensure it is interpreting
them correctly. See also Section 5.2.5, Auto Adjust, on page 12.
BRIGHT ±
Opens the backlight control bar. See also Section 5.2.1,Backlight, on
page 10.

Rosen Aviation 10.6” HD Widescreen Bulkhead Display
Document Number: 106282
Revision: D
Date: 03/20/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 9 of 30
5. OSD MENU OPTIONS
The OSD contains screen settings and options in menus and informational readouts that display
over the image, as shown below. Press MENU on the remote to open the Main Menu, as shown in
Section 5.1.
Press the ▲▼ buttons to navigate within the menu pages. Press the ►◄ buttons to navigate
between the menu page, options, and values columns. The yellow highlighted area shows the
currently selected option in the menu.
Figure 3 OSD menu pages
The available menu options will vary depending on which source signal is active.
Press MENU to choose a setting or an option.
Select the Back option to switch menu pages.
Press EXIT to close the OSD and save settings.
Note: The on-screen display will timeout and close automatically after no screen activity for a
preset amount of time, which is adjustable on the Technician MenuOSD Timeout option. See
Section 6.3, OSD Timeout on page 21.
5.1. Exit
Use Exit to close the OSD. When you press MENU, the OSD opens to this screen, as shown
below. Press MENU again to close the OSD from this screen.
Press the ▲▼ buttons to access the other menu pages in the OSD.
From other settings within the OSD, press EXIT on the remote control to close the OSD.
Figure 4 Opening screen for the Main Menu
Press ►to access
the menu page
options
Press ►to access
the menu option
values
Press ▼to
access menu
pages. The
selected menu
page is
highlighted.

Rosen Aviation 10.6” HD Widescreen Bulkhead Display
Document Number: 106282
Revision: D
Date: 03/20/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 10 of 30
5.2. User Menu
The Main Menu opens to the screen, shown in Figure 4 (above). Highlight User and press the ►
button to access the User menu options.
Press ▼▲ buttons to select a User option, and then press ENTER to change its value.
Figure 5 User menu options
5.2.1. Backlight
Use this setting to adjust the intensity of the LCD backlight.
From the User page, press the ►and ▼buttons to select Backlight, and then press
ENTER to open the control bar shown below.
Press the ◄or the ► buttons to change the value on the control bar accordingly.
Press ENTER to set the backlight brightness and close the control bar.
Figure 6 Backlight option
5.2.2. Aspect Ratio
Use Aspect Ratio to adjust the picture expansion to match the encoding of the source
image most closely.
To change the Aspect Ratio from the remote, press ASPECT, or select UserAspect
Ratio and then press ENTER. To switch the display between aspect ratio modes
(described below), press the ▲ ▼ buttons. Watch for proportional changes in the
background picture and choose the optimal mode for the source. Press ENTER to set the
mode and press EXIT to close the OSD.
Full Screen: Displays standard 4:3 source video in 16:9 aspect ratio by expanding the
image horizontally. Circles will appear as ovals in the central and outer portions of the
screen. If the source image is letterboxed, there will be black bars at the top and bottom
of the image. A 16:9 widescreen source will fill the screen with minimal distortion.
Source and Auto
Adjust are only
available in
Standard Operation
Mode, and Auto
Adjust is active only
with a VGA (RGB)
source.

Rosen Aviation 10.6” HD Widescreen Bulkhead Display
Document Number: 106282
Revision: D
Date: 03/20/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 11 of 30
Pillar Box: A standard 4:3 source image will appear with vertical black bars on the left
and right side of the image. If the image source is letterboxed, then there will also be
horizontal bars at the top and bottom of the image as well.
Letter Box Expanded: Expands the source video in the vertical and horizontal
dimensions to fill the display screen. Letterbox-format DVDs will have small or no bars
showing in this mode, while 4:3 aspect video sources will expand beyond the screen
boundaries and appear cropped.
Note: This mode is not available for RGB or a graphic, PC-based HDMI/DVI source.
5.2.3. Scheme
There are two default color settings or schemes: Natural and Vivid. If the screen colors
are not what you expect, select Scheme and press the ▲▼buttons to toggle between
the settings. The background picture’s colors change as you toggle between the settings.
Vivid uses a higher color saturation level above the Natural level.
Try both schemes to determine which one you like best before adjusting the other picture
quality settings.
Select UserScheme and then press ENTER to access the settings.
Select the setting and press ENTER to accept the changes, and then select Back and
press EXIT to close the OSD.
5.2.4. Source
(Available only when Operation Mode is set to Standard) The Source page lists all of the
available sources and shows which source is currently selected.
Figure 7 User Sources
Select UserSource and press ENTER to access the settings.
To switch the source, press the ▲and ▼buttons.
Press ENTER to accept any changes, and press ◄to remain in the OSD or EXIT to
close the OSD.
To switch sources directly from the remote control, close the OSD and press the
SOURCE button twice for each input.

Rosen Aviation 10.6” HD Widescreen Bulkhead Display
Document Number: 106282
Revision: D
Date: 03/20/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 12 of 30
5.2.5. Auto Adjust
(Available only when Operation Mode is set to Standard and the RGB source is active.)
Use Auto Adjust to force the display to evaluate the RGB signals and ensure that it is
interpreting them correctly. To perform an Auto Adjust within the OSD, select the option
and press ENTER. (From the remote, close the OSD and press the AUTO button.) The
screen will go black briefly while the signals adjust.
5.3. Image Adjust Menu
Use the Image Adjust menu options, as shown below, to control the color and picture quality.
Highlight Image Adjust and press the ►button to access the Image Adjust menu options.
Press ▼▲ buttons to select an Image Adjust option, and then press ENTER to change its value.
Figure 8 Image Adjust menu options
5.3.1. Scheme
Scheme is also available from the Main MenuUser page. For information about how
this option works, see Section 5.2.3,Scheme, on page 11. Changing the Scheme also
affects changes that you make to the User menu settings and is source specific.
5.3.2. Picture-quality Controls
The Brightness, Contrast, Saturation, Hue, and Sharpness menu options use control bars
to fine-tune different aspects of the picture quality. To adjust these options, press MENU
and the ▼ to select Image Adjust. Choose a menu option, and then press MENU to
open a control bar and adjust the value, similar to Figure 9, shown below.
Press the ◄or the ► buttons to increase or decrease the control’s value.
Press ENTER to set the menu option and close the control bar.
Press EXIT to close the OSD.
Figure 9 Sample picture-quality control bar
Picture-
quality
controls

Rosen Aviation 10.6” HD Widescreen Bulkhead Display
Document Number: 106282
Revision: D
Date: 03/20/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 13 of 30
5.3.3. Reset Scheme
Restores the values of the current scheme to their default settings, and it affects only the
current source. Use Reset Scheme to revert to the default screen colors if the other
Image Adjust options did not correct the screen quality.
Select Image AdjustReset Scheme and then press ENTER.
Press EXIT to close the OSD.
For information about the different Scheme modes, see Section 5.2.3 on page 11.
5.3.4. Image Adjust Advanced (Submenu)
Use the Image Adjust Advanced submenu options, as shown below, to fine-tune the
primary screen colors and to restore the monitor’s factory screen settings. Press the
MENU button and the ▼button to select Image AdjustAdvanced, and then press
ENTER to open the menu.
To close the menu, select the Back option, or press EXIT to close the OSD.
Figure 10 Advanced submenu options
5.3.4.1. Color Temperature
Use the Color Temperature options to change the warmth of the picture in all sources.
When you select Color Temperature, the screen changes, and a toggle appears to
switch between User and 6500K, as shown below.
Figure 11 Color Temperature options
Select the User setting and then press ENTER.
Press ▼to access the individual colors.
RGB
options
only

Rosen Aviation 10.6” HD Widescreen Bulkhead Display
Document Number: 106282
Revision: D
Date: 03/20/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 14 of 30
5.3.4.1.1. Color Levels: Red, Green, Blue
Setting the Color Temperature to User will make the Red, Blue, and Green options
active. Each color adjusts the low-level registers of its respective color value in the
picture.
Select the Image AdjustAdvancedColor Temperature and press ENTER.
Set Color Temperature to User, and then press ENTER.
Press ▼ to choose a color level, and then press ENTER to open a control bar to
adjust the value, similar to Figure 12 shown below.
Red: Press ◄ to show more cyan-colored tones, and press ►to intensify the
red tones.
Green: Press ◄ to show more magenta tones, and press ►to intensify the
green tones.
Blue: Press ◄ to show more yellow tones, and press ►to intensify the blue
tones.
Press ENTER to set the color and close the control bar.
Press EXIT to close the OSD.
Figure 12 Sample color-level control bar
5.3.4.2. Restore Defaults
This option restores the default screen settings from the user menus for all video
sources. It does not erase Technician Menu settings or change the internal time and
date. A Defaults Restored message appears in the lower corner of the menu after the
restore is complete.
Figure 13 Restore Defaults option
Status
message
RGB
options
only

Rosen Aviation 10.6” HD Widescreen Bulkhead Display
Document Number: 106282
Revision: D
Date: 03/20/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 15 of 30
5.3.4.3. Image Position Submenu
(RGB only) Use the Image Position options to center an RGB picture horizontally or
vertically on the screen. Note: Changing the resolution, source, or cycling power will
reset any adjustments to this submenu’s settings.
Select the Image AdjustAdvancedImage Position options and then press
ENTER.
Figure 14 Image Position option
5.3.4.3.1. Horizontal and Vertical Controls
(RGB only) From the Image AdjustAdvancedImage Position submenu, press
the ▼button to choose either Horizontal or Vertical,and then press ENTER to open
a control bar, similar to Figure 15 shown below.
Press the ◄ button to shift the picture left/up or the ►button to shift it to the
right/down.
Press ENTER to set the phase value and close the control bar.
Figure 15 Sample image positioning control bar
5.3.4.4. Auto Adjust
(RGB only) Use Auto Adjust when the RGB source is active to force the display to
evaluate the RGB signals and ensure that it is interpreting them correctly. To perform
an Auto Adjust within the OSD, select the option and press ENTER. (From the
remote, close the OSD and press the AUTO button.) The screen will go black briefly
while the signals adjust.

Rosen Aviation 10.6” HD Widescreen Bulkhead Display
Document Number: 106282
Revision: D
Date: 03/20/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 16 of 30
5.3.4.5. RGB Phase
(RGB only) Use RGB Phase to adjust the default phase value used for RGB signals.
Each RGB video source can have different phase values, which can result in the
RGB video image appearing to jitter. RGB Phase enables you to adjust the RGB
video image to eliminate jitter.
From the Image AdjustAdvanced submenu, press the ▼button to choose RGB
Phase and then press ENTER to open the control bar, as shown below.
Press the ►button to increase the RGB phase value until the jittering stops.
Press ENTER to set the phase value and close the control bar.
Figure 16 RGB Phase control bar
5.4. Info
Use the Information page to review operating status, view details about the display, and access
the Technician Menu.
To open the Info page, press the INFO button on the remote, or use the ▲▼ buttons from the
Main Menu and navigate to Info.
Notes:
Press ENTER or the ►button to highlight the Back option—required to access the
Technician Menu.
The firmware (FM) fields vary by model and are subject to change.
Figure 17 Info page
Use Info to verify video
source and resolution
settings.
Back option
active

Rosen Aviation 10.6” HD Widescreen Bulkhead Display
Document Number: 106282
Revision: D
Date: 03/20/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 17 of 30
6. TECHNICIAN MENU
To protect the display from accidental or unintentional adjustments, the Technician Menu is
accessible only with a special button combination. To avoid repeating this button sequence after
each change, the menu remains active until you manually close it.
Whenever there is a change to the OSD, exit the menu, and cycle
power for the changes to be fully accepted.
To open the Technician Menu, start with the display on, and press the following buttons in this
order: 1. Press INFO to open the Info page in the Main Menu.
2. With the Back option highlighted on the Info page, press the ▲▼▲▼▲▲▲ buttons
and then press MENU.
3. The Technician Menu opens. The options you see depend on the Mode Menu
settings. Splash Screen and the Source Mode menu will appear only when the Mode
MenuOperation Mode is set to Standard.
Figure 18 Technician Main Menus
To navigate the menu options, press the ▲or ▼buttons.
To close the Technician Menu and return to the Info Page, select the Back option and press
MENU. To close the Technician Menu and the OSD, press EXIT.
Note: The Main Menu options are not selectable while the Technician Menu is open.
Auto Detect mode (default)
Standard mode

Rosen Aviation 10.6” HD Widescreen Bulkhead Display
Document Number: 106282
Revision: D
Date: 03/20/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 18 of 30
6.1. Advanced Technician Submenu
This submenu provides installers and technicians more advanced controls of the image. The
active video signal and the Mode MenuOperation Mode setting determine which options will
appear in the Technician Advanced submenu.
Figure 19 Technician Advanced submenus
6.1.1. Factory Reset
Choose this option to perform a complete factory restore. It is similar to Reset Scheme in
the Main MenuAdvanced submenu; however, Factory Reset returns all options with
pre-determined defaults in both the User and Technician menus to their factory default
settings.
Highlight AdvancedFactory Reset and press ENTER.
A Reset Complete message appears after the display restores the default settings. A
Factory Reset will not change the Operation Mode (Auto Detect/Standard).
6.1.2. Comp/RGB 1
Use Comp/RGB 1 to specify which signal type the Component/RGB channel 1 will
accept. The options for channel 1 to display are either Component or RGB 1.
(Comp/RGB1 is available when you set the Operation Mode to Standard.)
Highlight AdvancedComp/RGB 1 and press ENTER.
Use the ▲▼ buttons to set the option, and then press ENTER.
Select Back to return to the Technician Menu.
Press EXIT when you are ready to exit the OSD.
The only options
available with SDI
active
Additional options
available with
Composite active
Auto Detect mode (default)
Standard mode
Not
available

Rosen Aviation 10.6” HD Widescreen Bulkhead Display
Document Number: 106282
Revision: D
Date: 03/20/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 19 of 30
6.1.3. 3D Comb Filter
(Composite only) When set to Enabled, the display will eliminate dot crawl and some
noise on stationary portions of the picture.
Highlight Advanced3D Comb Filter and press ENTER.
Use the ▲▼ buttons to set the option Enabled or Disabled, and then press ENTER.
Select Back to return to the Technician Menu.
Press EXIT when you are ready to exit the OSD.
6.1.4. Composite Sig (Signal)
(Composite only) This is a read-only screen that shows the signal strength of the
currently viewed Composite source. Composite Signal strength ranges from 0 to 1.25
Vpp in 0.25V increments. It will read NA (not available) if a Composite source is not
active or the AGC (Automatic Gain Control) (below) is set to Off.
6.1.5. AGC (Automatic Gain Control)
(Composite only) This option is a signal compensation tool that will accommodate for
strong and weak Composite signals.
Highlight AdvancedAGC and press ENTER.
Use the ▲▼ buttons to set the option On or Off,and then press ENTER.
Select Back to return to the Technician Menu.
Press EXIT when you are ready to exit the OSD.
6.2. Mode Menu
Use the Mode Menu options to specify the power and operation modes, and to access the SDI
Overscan settings.
From the Technician Main Menu, select Mode Menu and then press ENTER to open the
submenu, as shown below.
Figure 20 Technician Mode Menu

Rosen Aviation 10.6” HD Widescreen Bulkhead Display
Document Number: 106282
Revision: D
Date: 03/20/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 20 of 30
6.2.1. Power Mode
Use Power Mode to set display’s power mode to a startup state.
From the Technician Menu, press the ▼button to select Mode MenuPower Mode and
then press ENTER.
Use the ▲▼ buttons to set the option and then press ENTER.
Options include the following:
Auto On:The display always starts up in the ON state when 28V is applied
(default).
Auto Off:The display always starts up in the standby state when 28V is applied.
Restore Previous: The display returns to the previous power settings after any
power interruption.
Ground On: The display always starts up in the ON state when the power pin is
set to ground, and ignores all power commands from the IR, RS-232, and RS-485.
This setting will not take effect until you close the OSD.
Open On: The display always starts up in the ON state when the power pin is
open (not grounded), and ignores all power commands from the IR, RS-232, and
RS-485. This setting will not take effect until you close the OSD.
Momentary: The LCD power will toggle between on and off after the external
power discrete is momentarily grounded.
Select Back to return to the Technician Menu.
Press EXIT when you are ready to exit the OSD.
6.2.2. Operation Mode
Use Operation Mode to specify whether the display will operate in Standard (all
options/functions) or in Auto Detect mode. Changing modes will perform a factory reset
and the screen will briefly go black.
From the Technician Menu, press the ▼button to select Mode MenuOperation Mode
and then press ENTER.
Use the ▲▼ buttons to set the option and then press ENTER.
Options include the following:
Standard: The display is able to cycle between all available sources.
Auto Detect: (Default) The display detects the configured signals with the
following priority: Composite first and then SDI. If both signals are valid, but the
Composite signal drops out, the source will automatically switch to SDI. Whichever
signal is valid, the software switches to that input. In this mode, the user cannot
switch between sources.