Feig Electronic OBID i-scan ID ISC.PR101 Installation and operating instructions

APPLICATION-NOTE
preliminary
public (B)
2005-04-29
N50402-0e-ID-B.doc
OBI
D
i-scan
®
ID ISC.PR/MR101
Update USB-Controller

OBID i-scan®Application-Note ID ISC.PR/MR101-USB
FEIG ELECTRONIC GmbH Page 2 of 8 N50402-0e-ID-B.doc
Note
©Copyright 2005 by
FEIG ELECTRONIC GmbH
Lange Strasse 4
D-35781 Weilburg-Waldhausen
Tel.: [phone]
http://www.feig.de
With the edition of this document, all previous editions become void. Indications made in this man-
ual may be changed without previous notice.
Copying of this document, and giving it to others and the use or communication of the contents thereof are
forbidden without express authority. Offenders are liable to the payment of damages. All rights are reserved
in the event of the grant of a patent or the registration of a utility model or design.
Composition of the information in this document has been done to the best of our knowledge. FEIG
ELECTRONIC GmbH does not guarantee the correctness and completeness of the details given in this
manual and may not be held liable for damages ensuing from incorrect or incomplete information. Since,
despite all our efforts, errors may not be completely avoided, we are always grateful for your useful tips.
The instructions given in this manual are based on advantageous boundary conditions. FEIG
ELECTRONIC GmbH does not give any guarantee promise for perfect function in cross environ-
ments.
FEIG ELECTRONIC GmbH assumes no responsibility for the use of any information contained in
this document and makes no representation that they free of patent infringement. FEIG
ELECTRONIC GmbH does not convey any license under its patent rights nor the rights of others.
OBID®is a registered trademark of FEIG ELECTRONIC GmbH
OBID i-scan®is a registered trademark of FEIG ELECTRONIC GmbH
Windows®is a registered trademark of Microsoft Corporation

OBID i-scan®Application-Note ID ISC.PR/MR101-USB
FEIG ELECTRONIC GmbH Page 3 of 8 N50402-0e-ID-B.doc
Content
1. Safety Instructions / Warning - Read before start-up ! 4
1. Programming of the USB Controller Firmware 5
1.1. Installation USB_UpdateTool.......................................................................................5
1.2. Delete the old USB-Controller Firmware.....................................................................6
1.3. Install Device Driver......................................................................................................7
1.4. Start Update-Software „CYFX2Mfg“............................................................................8

OBID i-scan®Application-Note ID ISC.PR/MR101-USB
FEIG ELECTRONIC GmbH Page 4 of 8 N50402-0e-ID-B.doc
1. Safety Instructions / Warning - Read before start-up !
•The device may only be used for the intended purpose designed by for the manufacturer.
•The operation manual should be conveniently kept available at all times for each user.
•Unauthorized changes and the use of spare parts and additional devices which have not been
sold or recommended by the manufacturer may cause fire, electric shocks or injuries. Such
unauthorized measures shall exclude any liability by the manufacturer.
•The liability-prescriptions of the manufacturer in the issue valid at the time of purchase are valid
for the device. The manufacturer shall not be held legally responsible for inaccuracies, errors,
or omissions in the manual or automatically set parameters for a device or for an incorrect
application of a device.
•Repairs may only be executed by the manufacturer.
•Installation, operation, and maintenance procedures should only be carried out by qualified
personnel.
•Use of the device and its installation must be in accordance with national legal requirements
and local electrical codes .
•When working on devices the valid safety regulations must be observed.

OBID i-scan®Application-Note ID ISC.PR/MR101-USB
FEIG ELECTRONIC GmbH Page 5 of 8 N50402-0e-ID-B.doc
1. Programming of the USB Controller Firmware
With the update of the USB-Controller it is possible to use the USB-Reader ID ISC.PR/MR101 in
the scan mode. This is only necessary if you have one of the first USB-Reader ID ISC.PR/MR101
and the san mode is not available.
After that it is necessary to install the new reader firmware version 1.01 or higher. This can be
done with the “OBIDFirmwareUpdateTool” via the USB-Interface. This is described in the Applica-
tion Note „N30300-0e-ID-B.pdf“.
1.1. Installation USB_UpdateTool
Unzip the „USB_UpdateTool_PR_MR101.zip“ with the option „use path specification“
After that you will get the following tree:

OBID i-scan®Application-Note ID ISC.PR/MR101-USB
FEIG ELECTRONIC GmbH Page 6 of 8 N50402-0e-ID-B.doc
1.2. Delete the old USB-Controller Firmware.
•Start the demo program ID ISOStart.
•Press the „Open“-button:
•Select the prt-file “Clear_EEPROM_USB_Controller.prt” the folder“CYFX2Mfg:
•The protocol “07 E0 E0 00 00 7F BD” must be selected and then press the “Start”-button.
If an OK appears in the ProtocolWindow the EEPROM has been deleted successfully :
•Please unplug the USB-cable for about 10 seconds.

OBID i-scan®Application-Note ID ISC.PR/MR101-USB
FEIG ELECTRONIC GmbH Page 7 of 8 N50402-0e-ID-B.doc
1.3. Install Device Driver
•Please connect the USB-cable with the USB-Reader.
Windows recognize that a new USB-Devise has been connected and ask for the device driver.
•Follow the instruction of the Installation-Assistant.
•The driver you need now are stored in the folder „Driver“:
•After a successful installation the USB-Controller “Cypress Manufacturing Driver FX2 (no
EEPROM) appears in the Device Manager of Windows
•Please unplug the USB-Cable.

OBID i-scan®Application-Note ID ISC.PR/MR101-USB
FEIG ELECTRONIC GmbH Page 8 of 8 N50402-0e-ID-B.doc
1.4. Start Update-Software „CYFX2Mfg“
•After starting the software “CYFX2Mfg.exe” the following window will appear:
•Please connect again the USB-Cable with the USB-Reader.
The update process will be started automatically.
•Please wait until the message “Unplug Device” appears:
•Press the “Exit”-Button to finish the program.
•Disconnect the again the USB-Cable for about 10 sec.
Note:
•The update process has now been finished. If you connect the reader again with the PC
Windows will ask for the device driver (as it is by a new reader). Please use now the little
CDROM with the device driver which has been send together with the reader.
•To get the hole functionality (Scan Mode) you have to check if there is at least installed
the reader firmware version 1.01. If it is not please install the reader firmware version
1.01 by using the “OBIDFirmwareUpdateTool“.