Feli NCM-502 User manual

Ⅰ. Product and Specification Introduction
NCM-502
Heating Switch
ON/OFF
Ceramic Heater
Motor
Power Switch
Stainless Pot
Positioning Support
Pressure Adjustment Nut
Thumb Screw
Fixing Plate
Overcurrent Protection Button
Socket
Power cord and
plug
Pot Lid
Positioning Hole
Spring
Scraper
Natural Granite
Wheels
Granite Wheel Support
【Specification】
●Dimensions：L48.5 cm x W28 cm x H30 cm
●Weight：32 kg
●Pot capacity：4.5 kg
●Grinding Fineness：25μ or less
●Grinding Wheel Material：Natural Granite
●Container Material：Stainless Steel
●Device：Heating Device / Overcurrent
Protection Button

Ⅱ. Assembly Steps
1. Place the Stainless pot on the stand.
2. Place the granite wheel support inside the pot
vertically with the positioning hole facing
upward.
3. Place the spring over the positioning hole.
4. Install the positioning support. (Align one
end with the positioning hole and align the
other end with the two positioning rods.
Put pressure on the positioning support
and verify if the positioning support is
well installed.)
5. Positioning plate: align the positioning
plate with the positioning rods.
6. After tighten up the thumb screw, the
assembly is completed.

Ⅲ. Operating Instructions
1. Plug-in the machine and turn on the power.
2. Add cocoa paste into the pot. Do not
let the cocoa paste exceeds the height
of the stone mill.
3. Turn on the machine to start the refining
process. It is not a requirement but an
option to put on or not the transparent lid.
4. It is optional to use the ceramic heater.
It is suggested to make the heater face
onto the turning pot wall or face downward
to the pot inner during the refining process.
5. Higher or lower the granite wheels by turning
the Pressure Adjustment Nut to
increase/decrease the grinding pressure.
Note ： it is not recommended to lower too much the granite
wheels. It is adequate to make the granite wheels touch
slightly the bottom of the pot.
6. Ceramic heater： Turn ON/OFF.
Press downward the rod to turn off the
heater.

Push upward
the rod to
turn on the
heater.
Ⅳ. Cleaning Instructions
1. Turn off the power. (Unplug the power cord.)
2. Remove the transparent Lid.
3. Remove the Positioning Support and the Spring.
4. Remove the Granite Wheels.
5. Remove the Stainless Pot.
6. Pour out the refined paste.
7. Wash the Granite Wheels and the Stainless Pot with clean water, then use a towel
to wipe the machine shell. Do not put water on the machine nor wet the parts
installed interior of the machine to avoid being damaged by moist.

Ⅴ. Remarks
1.This machine can be made with a power voltage of：
□110V □220V
2. Melt chocolate into liquid condition before pouring into the pot. It is suggested
to use an oven or use a hot air gun to melt chocolate.
3.Ceramic heater is fragile, handle with care.
4. Do not touch the ceramic heater after turning it on to avoid being burned.
5. If the cocoa paste is lack of oiliness, it is suggested to pour additionally into the pot
cocoa oil in order to facilitate the de-acidifying process and the refining process.
Ⅶ. Troubleshooting
During the refining process, in the case when the power is suddenly off, please check
the overcurrent safety button located on the back of the grinder. If the button pops up,
clean the ingredients out of the machine. After pressing the overcurrent safety button,
restart the machine.
Ⅷ. Contact us
Feli Technology Co., Ltd.
TEL：[phone]
FAX：[phone]
E-mail：[email protected]
Website：www.felilook.com
ADD：6F, No.423, Sec. 3, Mingzhi Rd., Taishan Dist., New Taipei City 24355, Taiwan