Fellowes ESI Victory 3V-LX-C4848-24 Series User manual

Assembly instructions
Victory™LX 3-Leg
Model # 3V-LX-C4848-24-___
Model # 3V-LX-C4848-30-___
Model # 3V-LX-C4836-24-___
Model # 3V-LX-C4836-30-___
Model # 3V-LX-C3636-24-___
Model # 3V-LX-C3636-30-___
___ = SLV, BLK or WHT
Electric height adjustable table base

Page 2
Please review these instructions before beginning the installation. Use the illustrations below to check that all components needed for your installation
were provided with your order. Do not discard the packaging until the product works to your satisfaction.
Components and tools
Additional tools required
• Power drill with assorted drill bits
• Phillips screwdriver
• Phillips #1 and #2 bits
VictoryLX 3-leg Components and tools
Caution
• Hand tighten all hex head screws. Use power drill on self-tapping screws
only.
• Always check that screws used to attach components to the worksurface
are not too long for the thickness of the table.
table
thickness
top supports (2)
motor cable
locking clips (4)
center leg bracket (1)
center bracket
screws
M6x15
socket cap (8)
cord clips (10) feet screws
M3.5x16
#2 Phillips
flat head (10)
cam locks (3)
with cotter pin
outer legs
with motor (2)
center leg
with motor (1)
left frame segment (1
)r
ight frame segment (1)
M6x15
socket cap (8)
5mm
Allen key (1)
feet (2)
M4.8x22 #2 Phillips
round head (22)
frame screws
motor cables (3)power cable (1)
M3x20 #1 Phillips
round head (3)
M5x25 #2 Phillips
round head (2)
digital keypad (1)
control unit (1)

Page 3
VictoryLX 3-leg Assembly
Step #1: attach top supports to frame
The two top supports are left and right specific. The short end of each top support must be on
the same side of the frame as the longer frame channel at the open end of the frame segment.
• Insert the latches on the top support into the keyhole slots at the end of the frame channels.
• Tap the top support to fully seat it against the frame.
• Repeat to attach the top support on the other frame segment.
Step #2: assemble frame
With the table top facing down on a soft, clean surface, use the center leg bracket to connect the two frame segments.
• Loosen the eight set screws on each of the frame segments.
• Attach the center leg bracket to the left frame segment. The longer section of the cross channel at the open end should be at the top, toward the rear of the table.
— Align the 90°, 120°, or 180° holes on the bracket with the two holes on the ends of each channel, as shown. This example is a 120° table.
— Adjust the channels as necessary to align the holes.
• Secure the bracket to the left frame segment with four M6x15 socket cap screws. Use the 5mm Allen key to tighten the screws.
• Repeat this procedure to attach the right frame segment.
5mm Allen
key
longer channel
section
loosen all
set screws
M10x16
left frame
segment center leg bracket
align
holes
5mm Allen
key
repeat for
right frame segment
M6x15 socket cap
short end longer channel
top support
frame
channels
tap to firmly
seat top support

Page 4
VictoryLX 3-leg Assembly
Step #3: position frame on table
• Expand the cross channels to position the top supports 1" from the left and right edges of the table.
— Center the mounting tabs on the U-tubes to be sure each tube can be captured by the set screws.
— With longer tables, the U-tubes may need to “float” — they may not extend all the way into the cross channels (see below).
• Position the rear cross channels 6.5" or 9.5" from the rear edge of the table, depending on table depth: 6.5" for tables 24" deep and 9.5" for tables 30" deep.
• The center leg bracket should be centered under the angle of the table top. If it is not, check that the frame is positioned according to the diagram below.
• Tighten all set screws.
dotted line =
30" depth
tighten all
set screws
center mounting tabs
bracket is centered
under angle of table
top
support
top
support
expand
cross channels
cross channels
1"1"
6.5" 9.5"
“floating”
U-tubes

Page 5
install cam lock,
long end first
position leg
rotate lever
to lock leg
secure with
cotter pin
Step #5: attach left and right legs to frame
The left and right legs do not have a glide attached. The leg with the glide is the center leg.
• Remove the cotter pin from each of the three cam locks and save them for future use.
• Position the legs in the frame.
— First lower the protrusions on the motor housing into the notches.
— Then push the protrusions back toward the top supports into the narrower part of the notches.
• Install the cam lock. With the lever arm upward, insert the long end of the cam lock first, as shown.
• After the cam lock is installed, rotate its lever arm toward the leg until the lever is horizontal. This locks
the leg in place.
• Install the cotter pin to secure the cam lock.
• Check to be sure each leg is securely locked in position.
CAUTION: The cam locks must be in the locked position at all times to secure the legs in place.
Step #4: attach frame to table
• Use the M4.8X22 #2 Phillips round head screws to secure the frame to the underside of the worksurface.
— Use four screws for each top support, two screws for each cross support, one screw for each mounting tab, and six screws for the center leg bracket.
• Check that you have used a total of 22 screws to attach the frame to the table.
VictoryLX 3-leg Assembly
center leg
bracket
M4.8x22
#2 Phillips
round head
top
support
cross support
mounting tab
cam lock
cotter pin
remove
and save

Page 6
Step #7: attach feet to left and right legs
• Place the rectangular opening on the foot over the leg. The short end of the foot should be toward the rear of the table.
• Use the remaining eight M6x15 socket cap screws and 5mm Allen key to secure the feet in position.
• When installed correctly, the rear of the feet align with the rear of the table.
VictoryLX 3-leg Assembly
Step #6: attach center leg to frame
• Position the center leg (the one with the glide attached) into the center leg bracket, similar to the way the outer legs were positioned.
— First lower the protrusions on the motor housing into the notches.
— Then push the protrusions back into the narrower part of the notches.
• Install the remaining cam lock. With the lever arm upward, insert the long end of the cam lock first, as shown.
• After the cam lock is installed, rotate its lever arm toward the leg until the lever is horizontal to lock the leg in place.
• Install the remaining cotter pin to secure the cam lock.
• Check to be sure each leg is securely locked in position.
CAUTION: The cam locks must be in the locked position at all times to secure the legs in place.
position leg
in bracket
install cam lock,
long end first
route motor cable
under bracket secure
with cotter pin
rotate lever
to lock leg
rear
front
5mm Allen key
M6x15 socket cap
feet will align
with rear of table
foot for
24" table
foot for
30" table
glide

Page 7
Step #10: make cable and cord connections
• Connect the cable from the digital keypad to the control unit.
• Connect the motor cables to the control unit and to the short cable from each table leg.
• Connect the power cord to the control unit.
• Plug the power cord into an AC outlet. Be sure the cord can reach the outlet when
the table is raised to its highest position.
CAUTION: Do not operate the table until after initializing the system. See the
following step.
VictoryLX 3-leg Assembly
Step #8: attach digital keypad
• Attach the digital keypad using the three M3x20 #1 Phillips round head screws.
• Install the keypad in the “expanded” position. Pull the keypad away from the
mounting bracket to expand it.
• Position the digital keypad on the left or right side of the table, according to user
preference.
• Align the top of the keypad with the edge of the table so that the controls will be
easily accessible in the expanded position.
— To prevent accidental damage when not in use, the keypad may be pushed in,
under the table.
Step #9: attach control unit
• Position the control unit near the back of the table or between the
cross channels.
• Be sure that the cable from the keypad can reach the control unit and the
motor cables can extend from the control unit to all three leg motors.
• Attach the control unit using the two M5x25 #2 Phillips round head screws.
— Tighten the screws securely.
NOTICE: The table may not operate properly if the control unit is not
securely attached to the worksurface.
M5x25 #2 Phillips
round head
control unit
M3x20 #1 Phillips
round head
digital
keypad
align with
edge of table
when expanded
motor
cables
power
cord
keypad
cable

Page 8
Step #11: initialize the system
• Press and hold the UP sand DOWN t buttons simultaneously for more than 3 seconds.
— The legs will begin to move down at half speed of normal operation.
• Continue to press the UP sand DOWN t buttons.
— The legs will move down to the lowest position, then rebound 0.06" to 0.2" (2mm to 5mm)
and stop.
• Release the UP sand DOWN t buttons at the same time. This completes the initialization
procedure.
CAUTION: The initialization procedure above must be completed before operating the table.
NOTICE: The unit must be re-initialized anytime power is cut to the unit.
Step #12: test operation
• Press the UP sand DOWN tbuttons individually to test operation.
— End your test with the legs lowered.
— Unplug the power cord.
• If there are problems with operation, check that all cable and cord connections are secure,
and check that the control unit is securely attached to the worksurface.
— If problems continue, call ESI Customer Service: 800.833.3746.
NOTICE: The table must be re-initialized when power is restored.
Step #13: use the motor cable locking clips and cord clips to secure cables and cords
IMPORTANT: The cables and cords must not dangle under the table where they may present a hazard to the user or be accidentally disconnected.
• Motor cable locking clips:
— Push the motor cable locking clips into the square openings in the frame channels.
— Insert the motor cables into the clips.
• Cord clips:
— Place the cord clips onto the cables and cords.
— Use the M3.5x16 #2 Phillips flat head screws to fasten the cord clips to the table.
VictoryLX 3-leg Assembly
press and hold
UP and DOWN buttons
Note: Until the table is turned upright, the DOWN
button points up and the UP button points down.
press UP and DOWN buttons
to test operation
cord clip
M3.5x16
#2 Phillips
flat head
insert motor cable
into locking clip
motor cable
locking clip

Page 9
Step #14: turn the table upright
• With the assistance of a helper, turn the table upright and place it in its final position. IMPORTANT: There must be 1" (25mm) of clearance on all sides of the
worksurface (and other moving parts) to ensure free, unobstructed movement.
• If necessary, adjust the leveling glides on the feet and center leg to level the worksurface.
• Plug the power cord into an AC outlet.
• Re-initialize the system. See Step 11 on page 8. IMPORTANT: Be sure there are no obstacles under the table that would prevent it from reaching its lowest position.
• See the following pages for operating procedures.
NOTICE: Whenever the unit is unplugged or the power is cut, the table must be re-initialized.
VictoryLX 3-leg Assembly
WARNING: Lifting hazard. Single person lift could cause injury. Use assistance when moving or lifting.

Page 10
Important
• Before operating the table, the initialization procedure
must be completed. See Step 11 on page 8.
General operation
• Move the table up or down by pressing UP sor DOWN tuntil the
worksurface reaches the desired height.
• The table will continue to move up or down until you release the
button or until the maximum or minimum height is reached.
Memory stop positions
• Up to three memory stop positions can be used to save specific
heights of the worksurface. To set a specific position:
— Raise or lower the table to the position you want to save.
— The display on the digital keypad shows the worksurface height.
— Press and release the Sbutton. Then press the desired memory
button (1, 2or 3) within the next 3 seconds.
— Position 1, 2 or 3 is now saved.
• To move the worksurface to a memory stop position:
— Press and hold the desired memory button (1, 2or 3).
— The worksurface will move to the saved position and then stop.
— If you release the memory button before the saved position is
reached, table movement will stop.
Lower stop position
• To set the lower stop position (the minimum height of the table):
— Raise or lower the table to the desired minimum height.
— Press and hold S, then press and hold 1. Continue to press both
buttons for about 3 seconds.
— The letter “L” appears on the display. This means the minimum
height of the table is locked at its current position.
— Release both buttons.
— If there is a memory stop position lower than the new lower stop
position, that memory stop will be erased.
• To erase the lower stop position:
— With the table at its lower stop position, press and hold S, then
press and hold 2. Continue to press both buttons for about
3 seconds.
— The letter “C” appears on the display, indicating the lower stop
position has been erased.
— Release both buttons.
VictoryLX 3-leg Operation
UP
button
memory buttons
digital
display
DOWN
button
SET
button
Upper stop position
• To set the upper stop position (the maximum height of the table):
— Raise or lower the table to the desired maximum height.
— Press and hold S, then press and hold 3. Continue to press both
buttons for about 3 seconds.
— The letter “L” appears on the display. This means the maximum
height of the table is locked at its current position.
— Release both buttons.
— If there is a memory stop position higher than the new upper stop
position, that memory stop will be erased.
• To erase the upper stop position:
— With the table at its upper stop position, press and hold S, then
press and hold 2. Continue to press both buttons for about
3 seconds.
— The letter “C” appears on the display, indicating the upper stop
position has been erased.
— Release both buttons.
Adjusting the height readout
• To set the display height of the table to account for dierent
worksurface thicknesses:
— Move the table to the lowest position by pressing the DOWN t
button.
— Measure and record the height of the top of the worksurface.
— Press and hold Suntil the first LED number blinks.
— Press and hold UP sor DOWN t, changing the number in the first
LED position to the number desired.
— Press and hold Sagain until the second LED number blinks.
— Press and hold UP sor DOWN t, changing the number in the
second LED position to the number desired.
— Press and hold Sagain until the third LED number blinks.
— Press and hold UP sor DOWN t, changing the number in the
third LED position to the number desired.
— Finish setting this new height readout by pressing Sone more time.
• In inch format, the minimum adjustable amount (third digit) is 0.5".
(The third digit will be either 0 or 5.) In centimeter format, the
minimum adjustable amount (third digit) is 1 cm. (The third digit will
be 0 through 9.)

Page 11
Adjust gyro anti-collision sensitivity
• The default anti-collision sensitivity is G-1. To increase or decrease
the sensitivity of the table to obstacles in the path of its movement:
— Press and hold the Sbutton for more than 5 seconds. The display
shows “ ––– ”.
— Release Sand, within 3 seconds, press the 3button. The display
shows “G–X”, where X is a number from 0 to 4.
— Press the UP sor DOWN tbutton to increase or decrease the
gyro sensitivity level. There are five levels of sensitivity: “G – 0”,
“G – 1”, “G – 2”, “G – 3” and “G – 4”.
— “G – 4” indicates the highest sensitivity and and “G – 0” is no gyro
sensitivity.
— Press and hold the Sbutton for more than 3 seconds. This
completes the adjustment.
• If the legs do not move when general operation is attempted, the
gyro sensitivity adjustment may be too high.
Error Code Description Troubleshooting
E01 Leg malfunction 1. Check that the leg cables are securely plugged into the leg and control unit.
2. Inner parts of leg are broken. Replace the leg.
E03 Table top overload 1. Remove some weight from the table.
E04 Control unit malfunction 1. Re-initialize the system.
E05 Keypad button stuck 1. Toggle the button to restore normal function.
2. Replace the keypad if the button remains stuck.
E06 Communication interruption
1. Check the cable connection between the keypad and control unit. Verify that the cable is
securely plugged into the control unit.
2. If the problem is not resolved, replace the keypad or control unit.
E12 Gyro error 1. Communication is abnormal; power ON to normalize communication.
2. Table is tilted; straighten table or wait one minute before operating table.
IMPORTANT: The table should be re-initialized after every 1,000 cycles; every six months; or if power is cut or cable is unplugged accidentally.
When re-initializing, be sure there are no obstacles under the table that would prevent it from reaching its lowest position
VictoryLX 3-leg Operation
Changing the height display units
• There are 2.54 centimeters per inch. This makes it easy to tell what
the current display units are. For example, if the table is about three
feet high, the display will read approximately either 36.0 (inches) or
090 (centimeters).
• To change the display units from centimeters to inches or from inches
to centimeters:
— Press and hold S, then press and hold the DOWN tbutton.
Continue to press both buttons for about 3 seconds.
— The height information will change between centimeters and inches.
— Release both buttons.
Reset the table to factory settings (re-initialization)
• To reset the table to factory settings, re-initialize the control unit
using the keypad.
— Be sure there are no obstacles under the table that would prevent
it from reaching its lowest position.
— Press and hold the UP sand DOWN t buttons simultaneously
for more than 3 seconds. The legs will begin to move down at half
speed of normal operation.
— Continue to hold the UP sand DOWN t buttons.
— The legs will move down to the lowest position, then rebound
0.06" to 0.2" (2mm to 5mm) and stop.
— Release the UP sand DOWN t buttons at the same time. This
completes the re-initialization procedure.
• If one or more motors are changed in a system, the table must be
reset to factory settings.
Error codes

Victory™LX 3-Leg
Electric height adjustable table base
Please contact Customer Service with any questions or
comments at 800.833.3746 or visit our website at esiergo.com
LIMITED WARRANTY
ESI warrants this product to be free from defects in manufacturing for a period of 15 years on structural parts and 7 years on electrical parts from the date of original purchase. This warranty
extends only to the original purchaser, and does not apply if the product has been damaged or fails to function properly as a result of misuse, abuse, modification, alteration, or improper cleaning or
maintenance. This warranty does not apply to damage in shipment caused by carriers, damage caused during installation, normal wear and tear, or excessive use (meaning consistent use in excess
of an eight hour shift). ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL RETAIL
PURCHASE. ESI’s sole obligation under this warranty or any implied warranty, and the purchaser’s sole remedy, is limited to the repair or replacement, at ESI’s option, of the product or any defective
part. Costs (such as installation, labor fees or express shipping) incurred due to replacement of products are not covered under warranty. IN NO EVENT SHALL FELLOWES, ITS AFFILIATES, SUBSIDIARIES,
RELATED ENTITIES OR THEIR RESPECTIVE OFFICERS, DIRECTORS, OR EMPLOYEES, BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL, PUNITIVE, EXEMPLARY, OR SPECIAL DAMAGES.
To make a warranty claim, contact ESI at 800-833-3746 or [email protected]. You must provide proof of purchase, such as the original purchase order number.
The duration, terms and conditions of this warranty are valid worldwide, except where dierent limitations, restrictions or conditions may be required by local law.
© 2021 Fellowes, Inc.
|
Part # 412391 Rev B