K. Control Panel and LEDs
1. Reverse
2. ON/OFF
3. Forward
4. Bin full
5. Door open
2
KEY
CAPABILITIES
ENGLISH
Model SB-125i/SB-125Ci
Will shred: Paper, credit cards, CD/DVD’s, staples and small paper clips
Will not shred: Adhesive labels, continuous form paper, transparencies, newspaper, cardboard, large
paper clips, e folders, X-rays or plastic other than noted above
Paper shred size:
Cross-Cut...................................................................... 5/32 inches x 1-1/2 inches (3.9mm x 38mm)
Strip Cut.............................................................................................................7/32 inches (5.8mm)
Maximum:
Sheets per pass .............................................................................................................................18*
CDs/Cards per pass .........................................................................................................................1*
Paper entry width....................................................................................................9 inches (230mm)
*8.5 inches x11 inches, 20lb., (75g) paper at 120V, 60 Hz, C-125i 6Amps, C-125Ci 8Amps; heavier paper,
humidity or other than rated voltage may reduce capacity. Recommended daily usage rates:
100-150 paper passes; 100 cards; 10 CDs
Fellowes SafeSense®shredders are designed to be operated in office environments ranging
between 50 – 80 degrees Fahrenheit (10 – 26 degrees Celsius) and 40 – 80% relative humidity.
A. SafeSense
®
Technology
B. Paper entry
C. CD entry
D. Door
E. Basket (paper)
F. Basket (CD)
G. See safety instructions
H. Casters (2)
I. Disconnect power switch
J. Shipping bolts (wing nuts)
To be removed prior to operation
6. Remove paper
7. Overheat
8. Sheet capacity indicator
9. SafeSense
®
indicator (yellow)
10. Auto button
IMPORTANT SAFETY INSTRUCTIONS — Read Before Using!
• Keepawayfromchildrenandpets.Keephandsawayfrompaperentry.Always
set to off or unplug when not in use.
• Keepforeignobjects–gloves,jewelry,clothing,hair,etc.–away
from shredder openings. If object enters top opening, switch to
Reverse ( ) to back out object.
• Never use aerosol products, petroleum based lubricants or other flammable products
on or near shredder. Do not use canned air on shredder.
• Donotuseifdamagedordefective.Donotdisassembleshredder.Donotplace
near or over heat source or water.
• ThisshredderhasaDisconnectPowerSwitch(I)thatmustbeintheON(I)positionto
operate shredder. In case of emergency, move switch to OFF (O) position. This action will
stop shredder immediately.
• Avoidtouchingexposedcuttingbladesundershredderhead.
• KeepfingerawayfromCDholewhenshredding.
• Donotputforeignobjectsinpaperentry.
• Thegroundedsocket-outletshallbeinstalledneartheequipmentandshallbe
easily accessible.
•
WARNING: Shredder Stability - Secure Shredder to wall with hardware provided
following the instructions under Installation Instructions.
•
Product is intended for commercial use only, and not for use around children.
Do nothing and
shredder will go
automatically to sleep
mode
BASIC SHREDDING OPERATION
Press ( ) ON to activate
PAPER/CARD OR CD
1
Feed paper/card straight
into paper entry and
release
3
Plug in and put disconnect
power switch in ON
(I) position
To shred CDs rotate
CD flap into place
When finished
shredding set to
OFF ( )
or
7
www.fellowes.com features an extensive on-line support section with a number of self-service options
4
6
2
Hold CD at edge,
feed into CD
entry and release
57
Continuous operation:
45 minutes maximum
NOTE: Continuous operation
beyond 45 minutes will trigger
45 minute cool down period.
Jam Proof System
Eliminates frustrating jams by preventing
overloads and powering through misfed paper
Patented SafeSense®Technology
Stops shredder immediately when hands
are too close to the paper entry
Sleep Mode
Energy saving feature shuts down automatically
after 2 minutes of no shredding activity
INSTALLATION INSTRUCTIONSADVANCED PRODUCT FEATURES
1. Place shredder against the wall (drywall, wooden,
or concrete). Mark screw locations on wall
through back of cabinet.
2. Drill 1/4" hole in wall for the anchor plugs.
3. Insert white plastic anchor plugs into
drilled holes.
4. Insert (2) screws through back of cabinet and
thread black rubber spacer onto the screw.
5. From inside cabinet use Phillips screw driver to
secure shredder to the wall.
A.
B.
D.
C. K.
I.
G.
E.
F.
J.
H.
