Fenix HL16 User manual

Fenix HL16 Headlamp
Technical Parameters
ANSI/PLATO FL1 High Med Lo Red Red Flash
Output
70
Lumens
30
Lumens
4
Lumens 1 Lumen 1 Lumen/2Hz
Runtime
Ni-MH
Battery 3h 7h 60h 75h 150h
Alkaline
Battery 2.5h 7h 58h 85h 170h
Distance
35m 24m 8m \ \
Intensity
310cd 143cd 16cd \ \
Impact Resistance
1m
Waterproof
IP66
The abovemen ioned parame ers (lab- es ed by Fenix using one 2500mAh Ni-MH and he
included Alkaline ba ery) may vary be ween headlamps, ba eries and environmen s.
Cree XP-E2 R3 neu ral whi e LED wi h lifespan of 50,000 hours
Powered by one AA (Ni-MH/Alkaline) ba ery
62mm Leng h x 39.5mm Wid h x 37mm Heigh
55 grams (excluding ba ery)
Digi ally regula ed ou pu main ains cons an brigh ness
Red ligh for nigh vision; red flash for aler ing
60° il mechanism direc s he beam where needed
One-swi ch con rol for easy and fas opera ion
Reverse polari y pro ec ion o pro ec from improper ba ery inser ion

In elligen overhea pro ec ion pro ec s from high surface empera ure
Made of quali y aluminum and plas ic
Cer ified by CPSIA and REACH
Secure lock for kids: he included Allen wrench is needed for ba ery cover opening. For
adul use, remove he screw and replace he ba ery
Accessories: AA ba ery, Allen wrench, Spare O-ring
Operating Instruction
General Mode
Press and hold he swi ch for 0.5 seconds o urn ON/OFF he headlamp.
Wi h he lamp swi ched on, single click he swi ch o cycle hrough High→Low→Med.
Red Light
Single click he swi ch o en er Red ligh , one more clicking o en er Red flash. Click once again o
urn off red ligh mode.
The headlamp memorizes he las brigh ness level used in Whi e ligh mode. When nex urned
on, he previously used brigh ness level is recalled.
Mode S itching
Wi h he lamp on Red ligh mode, press and hold o ac iva e Whi e ligh mode.
Battery Specifications
Warning: 1. I is prohibi ed o use banned ba ery in case of overvol age explosion. Quali y
ba ery is s rongly recommended.
2. If he lamp will no be used for an ex ended period, remove he ba ery, or he lamp
could be damaged by elec roly e leakage or ba ery explosion.
Battery Replacement
1. Unscrew he locking screw o open he ba ery cover. Lower he holder o 90°angle, and press
Types Dimensions Nominal
Voltage Usability
Ni-MH Ba ery AA 1.2V Recommended √√
ARB-L14-1600U 14500 1.5V Recommended √√
Alkaline Ba ery AA 1.5V Usable √
Li hium Ba ery
(Non-rechargeable) AA 1.5V Cau ious ！
Li-ion Ba ery
(Rechargeable) 10440 3.7V Banned ×

he join of he holder and he headlamp wi h one humb.
2. Grasp he buckle hole wi h he humb of he o her hand hen pull up.
3. Inser he ba ery in accordance wi h he polari y mark, and close he ba ery cap.
Headband Assembly
No ice: The headband is fac ory assembled by defaul .
S ep 1: A ach he headband o he headlamp as shown, by firs sliding he band down o he
bo om of he slo s. Then hook he op edge under he op slo .
S ep 2: Adjus he headband by sliding he buckle o required leng h.
Usage and Maintenance
Disassembling he sealed head can cause damage o he headlamp and will void he
warran y.
Fenix s rongly recommends using quali y rechargeable Ni-MH ba ery, alkaline ba ery will
shor en he run ime wi h he lamp swi ched on high ou pu .
Long- erm use can resul in O-ring wear. To main ain a proper wa er seal, replace he ring
wi h an approved spare．
Periodic cleaning of he ba ery con ac s improves he lamp's performance as dir y con ac s
may cause he lamp o flicker, shine in ermi en ly or even fail o illumina e for he following
reasons:
A: The ba ery needs replacing.
Solu ion: Replace ba ery (Ensure ba ery is inser ed according o he manufac urer’s
specifica ions).
B: The hreads, PCB board con ac or o her con ac s are dir y.
Solu ion: Clean he con ac poin s wi h a co on swab soaked in rubbing alcohol.
If he above me hods don' work, please con ac your au horized dis ribu or.
Warning
The headlamp is a high-in ensi y ligh ing device capable of causing eye damage o he user or
o hers. Avoid shining he ligh direc ly in o anyone’s eyes.