Fenix HM60R User manual

Fenix HM60R Headlamp
Technical Parameters
Note: According to the ANSI/PLATO FL1 standard, the above specifications are from the results produced by Fenix
through its laboratory testing using one Fenix ARB-L18-2600 Li-ion battery under the temperature of 21±3°C and
humidity of 50% - 80%. The true performance of this product may vary according to different working
environments and the actual battery used.
*The Turbo output is measured in a total of runtime including output at reduced levels due to temperature or
protection mechanism in the design.
ANSI/PLATO
FL1
Spotlight Mode
Functional Mode
Output
Turbo
High
Med
Low
High
Med
Red
SOS
1200
lumens
350
lumens
130
lumens
30
lumens
350
lumens
70
lumens
5
lumens
5
lumens
Runtime
2 hours *
8 hours
18 hours
54 hours
8
hours
24
hours
100
hours
200
hours
Distance
116
meters
60
meters
36
meters
18
meters
33
meters
15
meters
5
meters
5
meters
Intensity
3400
candela
913
candela
330
candela
78
candela
268
candela
55
candela
7
candela
7
candela
Impact
Resistance
2 meters
Submersible
IP68

Product Features
l 1200 lumens maximum output, 116 meters maximum beam distance.
l Luminus SST40 white light LED, XP-G2 neutral white light LED; with a lifespan of 50,000
hours.
l Included a Fenix ARB-L18-2600 18650 rechargeable LI-ion battery and compatible with two
CR123A Lithium batteries.
l Spotlight, floodlight and red light combined.
l Frequency sensing: the brightness changes along with the speed.
l Hidden inner waterproof USB Type-C charging interface.
l A large all-in-one side switch.
l Made of quality PC and aluminum, lightweight and wear-resistant.
l Size: 3.35'' x 1.77'' x 1.77'' / 85 x 45 x 45 mm.
l Weight: 5.54 oz / 157 grams (including battery and headband).
Operating Instruction
On
Press and hold the switch for 0.5 seconds to enter spotlight mode, double click the switch to
enter functional mode.
Off
Press and hold the switch for 0.5 seconds to turn off the lamp.
Mode Switching
With the lamp switched on, press and hold the switch for 1.2 seconds to switch to another mode.
Output Selection
In Spotlight mode, with the lamp switched on, single click the switch to cycle through
Low→Med→High→Turbo.
In Functional mode, with the lamp switched on, single click the switch to cycle through
Red→Med→High→SOS.

Lock/Unlock
Lock: when the lamp is switched off, press and hold the switch for 3 seconds, the lamp will blink
red 3times to indicate locked status.
Unlock: when the lamp is locked, press and hold the switch for 3 seconds, the lamp will be
activated with 3 one-second red blinks and activated on Red Light mode.
In locked status, clicking the switch will activate 3 one-second red blinks to indicate locked status.
Intelligent Memory Circuit
The headlamp memorizes the last selected output on spotlight mode. When turned on again the
previously used output will be recalled. Each time the functional mode is entered with red light.
Battery Specifications
Type
Dimensions
Nominal
Voltage
Usability
Fenix ARB-L18 Series
18650
3.6V
Recommended
√√
Non-rechargeable Battery
(Lithium)
CR123A
3V
Usable
√
Rechargeable Battery
(LiFePO4)
16340
3.2V
Usable
√
Rechargeable Battery
(Li-ion)
18650*
3.6V
Caution
!
Rechargeable Battery
(Li-ion)
16340
3.6V
Banned
×
Rechargeable Battery
(LiFePO4)
18650
3.2V
Banned
×
Warning: *18650 Li-ion batteries are powerful cells designed for commercial applications and must be treated
with caution and handled with care. Only use quality batteries with circuit protection will reduce the potential for
combustion or explosion; but cell damage or short circuiting are potential risks the user assumes.

Battery Replacement
Unscrew the cap to insert the battery in accordance with the polarity marks, then screw the cap
back on.
Frequency Sensing
There is frequency sensing on Med and High output levels in spotlight mode.
1. Set frequency of step 150 times/minute as the standard. From 150 times/minute to 220
times/minute, the brightness increases proportionally with the frequency of step. When the
frequency of step reaches 220 times/minute, the brightness will increase to 150% of normal
brightness; when the frequency of step exceeds 220 times/minute, the brightness will remain at
150% of normal brightness.
2. When the frequency of step is lower than 150 times/minute, from 150 times/minute to 80
times/minute, the brightness decreases proportionally with the frequency of step. When the
frequency of step reaches 80 times/minute, the brightness is reduced to 70% of the normal
brightness; when the frequency of step is lower than 80 times/minute, it will maintain 70% of the
normal brightness. When the frequency is detected to decrease, the brightness starts to decrease
gradually after 10 seconds of delay.
Dual Distance Beam of Spotlight
The spotlight features Dual Distance Beam that provides long-range illumination while
maintaining up-close visibility.
Lamp Holder Angle Adjustment
The angle adjustment range of the lamp holder is 90° up and down.
Charging
1. Uncover the cap and plug the USB Type-C side of the charging cable into the charging port of

the lamp.
2. The indicator will display red while charging, and will turn to green when fully charged.
3. The normal charging time of the included Fenix ARB-L18-2600 18650 rechargeable Li-ion
battery is about 3 hours with a 5V/2A adapter.
4. When charging is complete, replace the anti-dust cap to ensure waterproof and dustproof
ability.
5. Recharge a stored headlamp every four months to maintain optimal Li-ion battery
performance.
6. When charging, the Low output level can be used, but charging time will be prolonged
Battery Level Indication
With the lamp switched off, single click the switch to check the battery status, the indicator will
last for 3 seconds.
Green light on: saturated 100% - 85%
Green light flashes: sufficient 85% - 50%
Red light on: poor 50% - 25%
Red light flashes: critical 25% - 1%
Note: This only works with Fenix ARB-L18 Series battery.
Intelligent Overheat Protection
The lamp will accumulate a lot of heat when used at Turbo output level for extended periods.
When the lamp reaches a temperature of 55°C or above, the lamp will automatically step down a
few lumens to reduce the temperature. When the temperature drops below 55°C, it will then
allow the user for the reselection of Turbo mode.
Low-voltage Warning
When the voltage level drops below the preset level, the headlamp is programmed to downshift
to a lower brightness level until Low output is reached. When this happens in Low output mode,
the lamp blinks 3 times every 5 minutes to remind you to timely recharge or replace the battery.

Note: This only works with Fenix ARB-L18 Series battery.
Headband Assembly
Note: The headband is factory assembled by default.
1. Adjust the headband by sliding the buckle to the required length.
2. Assemble top headband to better fix the headlamp. First fix the headband mount to the
headband, then fix one side of the top headband to the headlamp holder, and the other end to
the top headband mount.
Usage and Maintenance
l Disassembling the sealed head can cause damage to the lamp and will void the warranty.
l Fenix recommends using an excellent quality Fenix battery.
l If the lamp will not be used for an extended period, remove the battery, or the lamp could
be damaged by electrolyte leakage.
l Take out the battery to prevent accidental activation during storage or transportation.
l Long-term use can result in O-ring wear. To maintain a proper water seal, replace the ring
with an approved spare.
l Periodic cleaning of the battery contacts improves the lamp's performance as dirty contacts
may cause the lamp to flicker, shine intermittently or even fail to illuminate for the following
reasons:
A: The battery needs replacing.
Solution: Replace the battery (Ensure battery is inserted according to the manufacturer’s
specifications).
B: The contact point or contact of the battery or headlamp is dirty.
Solution: Clean the contact points with a cotton swab soaked in rubbing alcohol.
If the above methods don't work, please contact the distributor.
Included
Fenix HM60R Headlamp, Fenix ARB-L18-2600 Li-ion battery, USB Type-C charging cable, Spare
O-ring, User manual, Warranty card

Warning
l The headlamp is a high-intensity lighting device capable of causing eye damage to the user
or others. Avoid shining the lamp directly into anyone’s eyes.
l This headlamp will accumulate a lot of heat when used for extended periods, resulting in a
high temperature of the headlamp shell. Pay attention to safe use to avoid scalding.
l Do not shine an object at close range, so as to avoid burning the object or causing danger
due to high temperature.
l The LED of this headlamp is not replaceable; so the entire lamp should be replaced when
the LED reaches the end of its life.
l If any of the information provided in this manual is changed, the new version of the manual
shall prevail; if your included user manual is an old one, it acquiesces that we won't send a
new manual.