Ferroli TIBER B Series User manual

TIBER B 30 S
TIBER B 50 S
TIBER B 50
TIBER B 80
TIBER B 100
TIBER B 150
TIBER B 80 H
TIBER B 100 H
TIBER B
ATENTION!
DO NOT CONNECT TO THE MAINS BEFORE FILLING,
ASIRREVERSIBLE DAMAGE TO THE APPLIANCE MAY OCCUR.

Ferroli
TIBER B
1
2
3
5
8
12
13
Ferroli
TIBER B
water
water

2

TIBER B
30 S
230V~50/60Hz
A B B B B C
S M M M M L
TIBER B
50 S
TIBER B
50
TIBER B
80
TIBER B
100
TIBER B
150
TIBER B
80 H
TIBER B
100 H
97 97
(bar)
0.8
(8)
B
M
B
M
100.0 135.0
Vertical installation (H)-Horizontal installation
3

D
D
TIBER B 30S TIBER B 50S TIBER B 50 TIBER B 80 TIBER B 100 TIBER B 150 TIBER B 80H TIBER B 100H
Aф368 ф368 ф438 ф438 ф438 ф438 ф450 ф450
B 380 380 450 450 450 450 462 462
C 522 742 579 810 974 1280 810 974
D 116 116 151 151 151 151 237 237
E 364 584 403 634 798 1104 634 798
F 270 270 270 270 270 270
G 1/2"1/2"1/2"1/2"1/2"1/2"1/2"1/2"
H 100 100 100 100 100 100 100 100
L 170 390 199 430 549 855 385 549
NUMBER MODELOS(mm)
TIBER B 100-150L
4

5
TIBER B

Model TIBER B 30S TIBER B 50S TIBER B 50V TIBER B 80V TIBER B 100V TIBER B 150V TIBER B 80H TIBER B 100H
E(mm)364 584 403 634 798 1104
F(mm)270 270 270 270 270 270
L(mm)170 390 199 430 549 855 385 549
6

7

8
1- Flashing: anti bacteria function enabled;
Normally on: constant temperature mode
2- Power key
3/5- Adjustment key
short press: adjust;
Long press: fast adjustmentPress and hold the
combination key for 5S: start stop anti bacteria
mode
4- Temperature display / Countdown setting display /
Hour value display
6- Mode key
Short press: countdown appointment mode / constant
temperature / eco switch;
Long press: enter the countdown appointment setting
7-Always on: Eco mode;
Flashing: Countdown enabled
Heating
indicator

1. 2-colour indicator light
Constant temperature function； Red LED
Anti-Legionella function, Red LED (6/7) flashes
Shutdown and power on function, Green LED
2. STANDBY button
3. “-“button
4. Temperature display
5. “+“button
6. Mode selection button (Reservation mode/ constant temperature / ECO mode
7. Count down appointment mode. Red LED(6) light up
During the heating stage, the decimal point in the lower right corner of the LED digital tube will flash
and display until the set temperature is reached, the decimal point goes out.
If the temperature drops ,for example after hot water has been used ,it automatically starts to heat
water again and the decimal point will flash again.
Press the to activate to the “smart” function. The corresponding LED indication(7)will light up.
If you want to adjust the temperature manually,you will need to turn off the smart function.
9
TIBER B 3/Appointment.
Can change the modes according to press the button.

Continue to press the button. to enter the appointment mode.
Press the mode key to switch to the countdown reservation mode, (6) light flashes.
Countdown reservation function, in the countdown reservation mode, the electric water heater will be
heated to the set temperature in advance according to the time point reserved by the user.
Countdown appointment mode: press 3S for a long time to enter the countdown appointment
setting, blink, enter the countdown setting, use and press the key to adjust the countdown.
After setting, press the mode key briefly to confirm. If no operation is performed for 5S in the
setting, it will be saved by defaultCurrent setting and exit the setting state. When the electric water
heater is powered off, it will exit the countdown appointment mode.
Continue to press the door button, the corresponding LED(7) light will go out, and exit the
appointment function.
10
APPOINTMENT FUNCTION
Activate this function by pressing the “-“ and “+”keys at the same time for 5 seconds Once activation
is confirmed, (1) light will flash rapidly for 5 seconds and then the light will Keep flashing.
To switch off the anti-Legionella function,repeat the previous steps(press”-”and “+” keys for 5
seconds) ; once deactivation is confirmed, The indicator( light 1) stops flashing and stays on.
This function can work in All modes.

11

If there is a malfunction, the unit will enter “fault mode” and 4 will display the corresponding fault code.
12
Cut off the power and start the water heater again, if the fault has been removed.
The heater will rwsume normal operation. If this is not the case, 4will continue to display the fault code.
The type of malfunction will be indicated by the 4 as follows”
E4 LED flashing – Operating without water
E2/E5 LED flashing – Temperature sensors NTC 1/NTC 2 broken
E6 LEDS flashing – Fault in sensor differential
E7 LED flashing – Water overheating
E8 LED flashing – water overheating detected by an individual sensor

Ferroli
13