FireAngel Wi-Safe 2 Thermoptek WST-630-NEU User manual

Drawing No: GN4458
Revision: 1
Drawn By: Hannah
Brannon
Sprue Safety Products Ltd. Artwork Information
Ensure that you are printing / manufacturing from the original artwork le and not a preview
CONFIDENTIAL: The information provided in this document is proprietary to Sprue Aegis Plc/FireAngel Ltd and as
such should only be used/shared for the exclusive manufacture of those products specied.
Title/Description:
User Manual
Material:
60GSM Wood Free Paper
Perfect Bound
Used On / Used For:
WST-630-NEU
Size:
W - 121mm / H - 129mm
Supplier:
CICAM
Print Colours:
Black
WIRELESS INTERLINK SMOKE ALARM + 10 YEAR LIFE
TRÅDLØS SERIEFORBINDELSE RØGALARM + 10 ÅRS LEVETID
LANGATTOMASTI YHTEENLIITETTÄVÄ PALOVAROITIN + 10 VUODEN KÄYTTÖIKÄ
TRÅDLØS SAMMENKOBLBAR RØYKVARSLER MED + 10 ÅRS BRUKSTID
TRÅDLÖS SAMMANKOPPLINGSBAR BRANDVARNARE LIVSLÄNGD 10+ ÅR
WST-630-NEU
Content Quality:
Hannah Brannon
Product Information:
Gaurav Arora
Certication marks:
Ian Ballinger
APPROVAL:
Messaging: Messaging:
Simon McMahon
User Manual
Brugsvejledning | Käyttäjän ohjekirja
Brukerhåndbok | Användarhandbok

3
0832
EN 14604:2005 + AC:2008
Smoke Alarm Devices
Røgalarm apparater
Palovaroitinlaitteet
Røykvarsler-enhet
Brandvarnare
DoP: SADOPWST-630-01
15 651d/12
WST-630-NEU
GN4458 / R1
Sprue Safety Products Ltd.
Vanguard Centre, Sir William Lyons Road, Coventry CV4 7EZ UK
A Sprue Brand
Introduction . . . . . . . . . . . . 4
Automatic power engage. . . . .4
Sensor technology . . . . . . . . 4
Application . . . . . . . . . . . . 5
Thermoptek
SensorTechnology . . . . . . . . 5
Positioning . . . . . . . . . . . . 6
How to install your
smoke alarm . . . . . . . . . . . 8
Interlinking your WST-630-NEU . .9
CONTENTS
The original English version of the manual, from which this translation was taken,
has been independently approved. In case of discrepancy with translated parts,
Sprue Safety Products Ltd conrms that the English guide is true and correct.
Independently tested to RF standard / Uafhængigt testet til RF-standard /
Testannut riippumattomasti radiotaajuus standardin / Uavhengig testet etter
RF-standarden / Oberoende tester till RF-standard:
EN 300 220-2 V2.4.1
EN 301 489-3 V1.6.1
EN 301 489-1 V1.9.2
E-mail/Sähköposti/E-post: support@reangel.eu
Web/hjemmeside/WWW/Nett/Web:www.reangel.eu
DK: 0800 711 151 / FI: 0880 055 2130 / NO: 0800 69 127 / SE: 0200 123 598
This user guide is also available in large text and other formats.
Please email support@reangel.eu for further information.

EN
3
Introduction . . . . . . . . . . . . 4
Automatic power engage. . . . .4
Sensor technology . . . . . . . . 4
Application . . . . . . . . . . . . 5
Thermoptek
SensorTechnology . . . . . . . . 5
Positioning . . . . . . . . . . . . 6
How to install your
smoke alarm . . . . . . . . . . . 8
Interlinking your WST-630-NEU . .9
Operation . . . . . . . . . . . . 10
LED indicators. . . . . . . . . . 12
Alarm test . . . . . . . . . . . . 13
Alarm Smart Silence™ . . . . . 13
Maintenance. . . . . . . . . . . 15
Troubleshooting. . . . . . . . . 16
Disposal . . . . . . . . . . . . . 19
Warranty . . . . . . . . . . . . . 19
CONTENTS
The original English version of the manual, from which this translation was taken,
has been independently approved. In case of discrepancy with translated parts,
Sprue Safety Products Ltd conrms that the English guide is true and correct.
This user guide is also available in large text and other formats.
Please email support@reangel.eu for further information.

EN
4 5
THERMOPTEK SENSOR
TECHNOLOGY
The state of the art thermally-enhanced
optical sensing chamber provides a fast
reaction to both slow smouldering and
fast aming res in a single alarm. The
Thermoptek technology constantly monitors
temperature changes and if a rate of
temperature rise is detected the sensitivity of
the alarm is increased meaning it has a fast
response time to fast aming res as well as
slow smouldering res.
APPLICATION
WARNING: Your FireAngel smoke alarm
can be installed into a new build property as
additional protection to an existing smoke
detection system only. It cannot be used
as a substitute for a hard wired system as
required in new build properties. In this type
of property the building regulations require
alarms to be interlinked. You can obtain
further information from your local re service
or building control department at your local
council ofces. These sources generally
provide advice on new builds or projects
that require planning permission. Your
smoke alarm typically meets the minimum
requirements for family living units in existing
buildings, as long as at least one unit is
installed on each oor/level of your property.
In order to achieve the earliest re warning,
we recommend that a smoke alarm is tted in
all rooms where the temperature is normally
between 4°C (40°F) and 38°C (100°F). Check
INTRODUCTION
The FireAngel WST-630-NEU wireless
interlink multi-criteria high performance
detector is the ultimate alternative to
traditional alarms. Ground breaking
Thermoptek technology combines the
very latest in optical sensing with thermal
enhancement, providing fast response to
both fast aming and smouldering res ,
eliminating the need for ionisation sources
which can be harmful to the environment.
Up to a maximum of 50 WST-630-NEU
alarms can be wirelessly interlinked, creating
a network. If any smoke alarm sounds, it
triggers all other alarms in its network to
sound simultaneously. This provides the
earliest possible warning of a re.
Alarm signals are passed between all
WST-630-NEU’s in the network, increasing
the network range and reliability.
IMPORTANT: This user manual contains
important information regarding the
operation of your FireAngel smoke alarm.
Ensure you read this user manual fully before
installing and operating the alarm. If you are
installing this smoke alarm for use by others,
you must leave this manual (or a copy of it)
with the end user.
AUTOMATIC
POWER ENGAGE
Your 10 year life smoke alarm is powered
by an internal lithium power pack which is
supplied in a deactivated state. The power
pack is automatically enabled when the
alarm is fully locked on to the base plate and
disabled when removed.
IMPORTANT: Your alarm will not work until
it is correctly located and secured onto the
base plate.
SENSOR TECHNOLOGY
Traditionally 3 types of sensor technology
have been used in domestic self-contained
re alarms. Optical smoke alarms are
typically more effective at detecting slow
burning res, which can smoulder for hours
before bursting into ames. Ionisation
smoke alarms are generally more effective at
detecting fast, aming res which consume
combustible materials rapidly and spread
re quickly. Heat alarms are triggered when
room temperature reaches a set point
(typically 56°C). These alarms are generally
used in locations where other alarm types
are not suitable, such as kitchens.

EN
4 5
THERMOPTEK SENSOR
TECHNOLOGY
The state of the art thermally-enhanced
optical sensing chamber provides a fast
reaction to both slow smouldering and
fast aming res in a single alarm. The
Thermoptek technology constantly monitors
temperature changes and if a rate of
temperature rise is detected the sensitivity of
the alarm is increased meaning it has a fast
response time to fast aming res as well as
slow smouldering res.
APPLICATION
WARNING: Your FireAngel smoke alarm
can be installed into a new build property as
additional protection to an existing smoke
detection system only. It cannot be used
as a substitute for a hard wired system as
required in new build properties. In this type
of property the building regulations require
alarms to be interlinked. You can obtain
further information from your local re service
or building control department at your local
council ofces. These sources generally
provide advice on new builds or projects
that require planning permission. Your
smoke alarm typically meets the minimum
requirements for family living units in existing
buildings, as long as at least one unit is
installed on each oor/level of your property.
In order to achieve the earliest re warning,
we recommend that a smoke alarm is tted in
all rooms where the temperature is normally
between 4°C (40°F) and 38°C (100°F). Check
the section on ‘Positioning’ to ensure that
the smoke alarm is to be correctly positioned
for the particular dwelling into which it is
intended to be installed.
WARNING: The alarm positions shown
below are based on typical homes.
Construction and layout of individual
dwellings will vary, so this should be
regarded only as a guide. Check with your
local re station for further guidance.
The FireAngel WST-630-NEU is designed to
be wirelessly interlinked with other
WST-630-NEU smoke alarms. The
WST-630-NEU is not designed to
communicate with wireless smoke alarms
from other ranges or manufacturers.
LOUNGE
CELLAR
BEDROOMBEDROOM HALL
DINING ROOM
MINIMUM RECOMMENDATIONS
EXISTING HOMES
NOTE: Kitchens should be covered by a
self contained heat detector.
RECOMMENDED FOR ADDITIONAL
PROTECTION
AUTOMATIC
POWER ENGAGE
Your 10 year life smoke alarm is powered
by an internal lithium power pack which is
supplied in a deactivated state. The power
pack is automatically enabled when the
alarm is fully locked on to the base plate and
disabled when removed.
IMPORTANT: Your alarm will not work until
it is correctly located and secured onto the
base plate.
SENSOR TECHNOLOGY
Traditionally 3 types of sensor technology
have been used in domestic self-contained
re alarms. Optical smoke alarms are
typically more effective at detecting slow
burning res, which can smoulder for hours
before bursting into ames. Ionisation
smoke alarms are generally more effective at
detecting fast, aming res which consume
combustible materials rapidly and spread
re quickly. Heat alarms are triggered when
room temperature reaches a set point
(typically 56°C). These alarms are generally
used in locations where other alarm types
are not suitable, such as kitchens.

EN
67
• In insect infested areas. Insects can
clog openings to the sensing chamber,
preventing smoke entry or causing
unwanted alarms.
• Within 30cm (12”) of a uorescent light
tting which emits electrical ‘noise’ that
can prevent correct alarm operation.
• In wall positions that are more than 30cm
(12”) away from the ceiling (see ‘How to
install your smoke alarm’).
• In ‘dead air’ spaces (see following
diagram).
• Within 30cm (12”) of light ttings or other
ceiling based obstructions.
WARNING: Prolonged exposure to
temperatures outside those stated above
will reduce product life.
IMPORTANT: Obstructions such as steel
reinforcement in concrete could block
or impede the wireless signal. While the
wireless range is over 200 metres in
clear air / clear line of sight, the effective
range may be reduced by wall and other
obstructions in the building. Always
ensure that after any building work or after
repositioning large items of furniture (beds,
sofas, shelving units etc.), you carry out an
alarm test on all networked smoke alarms
to ensure they are all still working. It is
recommended not to exceed 35m as the
maximum distance between smoke alarms
in the network.
POSITIONING
Thermoptek smoke alarms are less prone
to false alarms from cooking fumes, and
are therefore suitable for locations near
kitchens. However like other types of smoke
alarms, Thermoptek smoke alarms can be
susceptible to nuisance alarms from steam
and should not be located too close to
bathrooms and showers.
It is recommended that your FireAngel
smoke alarm is NOT to be tted in the
following locations:
• Bathrooms, shower-rooms, and other very
damp or humid areas, where the moisture
can cause unwanted alarms.
• Kitchens. Kitchen areas should be
protected with self-contained Heat
Alarms, as the combustion particles from
cooking in kitchens will result in unwanted
alarms and permanent contamination of
the smoke alarm’s sensor.
• In areas where excessive dust or dirt could
contaminate the sensing chamber, making
it over sensitive or impairing smoke entry.
• In areas where the ambient temperature
is not controlled and may regularly drift
below 4°C (40°F) or above 38°C (100°F)
e.g. unheated buildings, open attic
spaces.
• Very dirty, dusty or greasy areas.
• In very draughty areas, such as close to
ceiling fans or fresh air vents. Draughts
can blow smoke away from the alarm.
Multi-family or mixed occupant residence
(Tenancy building, student accommodation)
Your FireAngel smoke alarm can also
be used in individual ats and bedsits,
providing the same conditions are met as for
a single-family residence. However, there
must already be a primary re detection
system that meets regulatory requirements
for common areas such as lobbies and
hallways.
Institutions and Hotels
This includes motels, hospitals, day care
facilities, long-term health care facilities,
boarding houses and dormitories. Your
WST-630-NEU smoke alarm can be used
in individual sleeping/resident rooms,
providing the same conditions are met as
for a single-family residence. However, there
must already be a primary re detection
system that meets regulatory requirements
for common areas such as lobbies and
hallways. Use of the WST-630-NEU smoke
alarm in common areas may not provide
sufcient re warning to residents or meet
regulatory requirements.
Mobile Homes and Caravans
This smoke alarm is suitable for use in
mobile homes and caravans.
Commercial and Industrial Premises
This smoke alarm is not intended for any
non-residential, commercial or industrial
application, nor for any other purpose than
described above.

EN
67
• In insect infested areas. Insects can
clog openings to the sensing chamber,
preventing smoke entry or causing
unwanted alarms.
• Within 30cm (12”) of a uorescent light
tting which emits electrical ‘noise’ that
can prevent correct alarm operation.
• In wall positions that are more than 30cm
(12”) away from the ceiling (see ‘How to
install your smoke alarm’).
• In ‘dead air’ spaces (see following
diagram).
• Within 30cm (12”) of light ttings or other
ceiling based obstructions.
WARNING: Prolonged exposure to
temperatures outside those stated above
will reduce product life.
IMPORTANT: Obstructions such as steel
reinforcement in concrete could block
or impede the wireless signal. While the
wireless range is over 200 metres in
clear air / clear line of sight, the effective
range may be reduced by wall and other
obstructions in the building. Always
ensure that after any building work or after
repositioning large items of furniture (beds,
sofas, shelving units etc.), you carry out an
alarm test on all networked smoke alarms
to ensure they are all still working. It is
recommended not to exceed 35m as the
maximum distance between smoke alarms
in the network.
Note: Up to 50 WST-630-NEU smoke
alarms and/or Wi-Safe 2 accessories can
be learned in to a single network.
1 METRE
(3 FEET) DEAD
AIR SPACES
100MM
(4 INCHES)
100MM
(4 INCHES)
BEST LOCATION
(IN CENTRE OF CEILING)
DEAD
AIR SPACES
POSITIONING
Thermoptek smoke alarms are less prone
to false alarms from cooking fumes, and
are therefore suitable for locations near
kitchens. However like other types of smoke
alarms, Thermoptek smoke alarms can be
susceptible to nuisance alarms from steam
and should not be located too close to
bathrooms and showers.
It is recommended that your FireAngel
smoke alarm is NOT to be tted in the
following locations:
• Bathrooms, shower-rooms, and other very
damp or humid areas, where the moisture
can cause unwanted alarms.
• Kitchens. Kitchen areas should be
protected with self-contained Heat
Alarms, as the combustion particles from
cooking in kitchens will result in unwanted
alarms and permanent contamination of
the smoke alarm’s sensor.
• In areas where excessive dust or dirt could
contaminate the sensing chamber, making
it over sensitive or impairing smoke entry.
• In areas where the ambient temperature
is not controlled and may regularly drift
below 4°C (40°F) or above 38°C (100°F)
e.g. unheated buildings, open attic
spaces.
• Very dirty, dusty or greasy areas.
• In very draughty areas, such as close to
ceiling fans or fresh air vents. Draughts
can blow smoke away from the alarm.

EN
89
alarm should ash approximately once every
45 seconds to show that it is active.
WARNING: Removing the smoke alarm from
its base plate will de-activate the unit and
prevent it from detecting smoke.
4. Test Your FireAngel Smoke Alarm
After tting the alarm to the base plate,
wait for 5 seconds for the alarm to settle
then test the alarm. See ‘Alarm Test’ on
page 13.
INTERLINKING YOUR
WST-630-NEU
SMOKE ALARMS
This smoke alarm contains an inbuilt RF
module, and enables you to wirelessly
interlink two or more smoke alarms and
create a network. Therefore WST-630-NEU
alarms need to be “learned in” or interlinked
in order to communicate with each other.
If one alarm activates, all other interlinked
smoke alarms will also sound. Note that
WST-630-NEUs can only be interlinked with
other WST-630-NEUs and products within
the FireAngel Wi-Safe 2 range.
“Learning in” (interlinking) your Smoke
Alarms:
The process below describes ‘learning in’
two alarms into a network, “Alarm 1” and
“Alarm 2”.
1. Alarm 1
Install Alarm 1 as described on page 8.
HOW TO INSTALL YOUR
SMOKE ALARM
IMPORTANT: Make sure you have read and
understood this manual before installing
your smoke alarm.
1. Preparation
The base plate should be attached to
the ceiling or wall.
Break out the tabs from the base plate.
Use the xing slots on the base plate as
a guide when marking the position of the
drill holes. With an appropriately sized
drill, drill the holes and insert the plastic
xing anchors supplied (if required).
Base plate tabs
2. Install Base Plate
Fit the base plate to the ceiling or wall
using the screws provided.
3. Fit Your FireAngel Smoke Alarm
To t to the base plate included in this
pack, position the alarm on the base plate
then twist it clockwise until the alarm is
locked in position. Make sure the alarm is
twisted on fully.
The power pack will now activate. The red
LED (visual indicator) on the front of the

EN
89
alarm should ash approximately once every
45 seconds to show that it is active.
WARNING: Removing the smoke alarm from
its base plate will de-activate the unit and
prevent it from detecting smoke.
4. Test Your FireAngel Smoke Alarm
After tting the alarm to the base plate,
wait for 5 seconds for the alarm to settle
then test the alarm. See ‘Alarm Test’ on
page 13.
INTERLINKING YOUR
WST-630-NEU
SMOKE ALARMS
This smoke alarm contains an inbuilt RF
module, and enables you to wirelessly
interlink two or more smoke alarms and
create a network. Therefore WST-630-NEU
alarms need to be “learned in” or interlinked
in order to communicate with each other.
If one alarm activates, all other interlinked
smoke alarms will also sound. Note that
WST-630-NEUs can only be interlinked with
other WST-630-NEUs and products within
the FireAngel Wi-Safe 2 range.
“Learning in” (interlinking) your Smoke
Alarms:
The process below describes ‘learning in’
two alarms into a network, “Alarm 1” and
“Alarm 2”.
1. Alarm 1
Install Alarm 1 as described on page 8.
2. Alarm 2
Install the base plate for Alarm 2 in one
of the recommended locations (see
Positioning on page 6) Do not t the
second alarm to its base plate yet.
3. Alarm 2
Using a pen, a very small screwdriver
or paper clip that has been opened out,
briey push and release the learn button
located in a circular hole in the back of
Alarm 2.
The red LED next to the learn button
will ash briey then light up for
approximately ve seconds to show that
it is ready to receive the “learn in” signal.
During the next ve seconds you will need
to briey press the test button on Alarm 1
to wirelessly interlink the two alarms.
Alarm 1:
will give an audible sound consisting of
2 cycles of 3 loud beeps.
Circular hole
3. Fit Your FireAngel Smoke Alarm
To t to the base plate included in this
pack, position the alarm on the base plate
then twist it clockwise until the alarm is
locked in position. Make sure the alarm is
twisted on fully.
The power pack will now activate. The red
LED (visual indicator) on the front of the

EN
10 11
IMPORTANT: If your WST-630-NEU smoke
alarm enters a low power pack condition, it
will emit an audible “chirp” approximately
once every 45 seconds. All other
WST-630-NEU alarms in the network will
also emit an audible low battery chirp once
every 4 hours. This will continue until the
smoke alarm which has the low battery
condition is removed.
Fault Indication
If the amber LED ashes and an audible
‘chirp’ is heard at a different time, this
indicates that there is a fault; the unit may
not detect smoke and may not go into alarm
in the event of a re. If this occurs it is
strongly recommended that you replace the
alarm immediately.
Alarm Condition
If the WST-630-NEU goes into alarm, all
interlinked alarms will also sound 3 loud
beeps which continually repeat until the
cause of the alarm being activated is found
and resolved.The red LED will only ash
rapidly (once per second) on alarms that
have responded directly to smoke.
Alarm 2:
The red LED on the wireless module of
alarm 2 will ash to indicate that it has
been “learned-in” successfully.
Note: If the test button is not pressed
quickly enough (before the red LED
on the wireless module of Alarm 2 has
extinguished), the learn-in process will
fail. If this happens, repeat the process
again, as described above.
5. Fit Alarm 2 onto its base plate to
complete the installation.
6. Additional alarms should be “learned-in”
the same way. When learning in additional
alarms, any alarm already in the network,
can be used as ‘Alarm 1’. This means that
you can “learn-in” the additional alarm
into any alarm already in the network.
It will then become part of the whole
network. You do not have to “learn it in”
into each alarm in the network.
7. After completing the “learn-in” procedure,
test the alarms as described in “alarm
test”.
If any interlinked alarm fails to respond to
the “alarm test”, remove it from its base
plate and repeat the learning in process.
OPERATION
Normal Condition
The red LED on the front will ash
approximately every 45 seconds to show
that the alarm is active.
Low Power Pack Condition
IMPORTANT: Your smoke alarm requires
the power pack to have sufcient capacity
of power to operate correctly. Should your
FireAngel smoke alarm enter a low power
pack condition, the unit will emit an audible
‘chirp’ approximately once every 45 seconds
and the amber LED will ash at around the
same time. When this occurs it is strongly
recommended you replace the alarm
immediately and in any event within 30 days.
Your FireAngel smoke alarm will continue to
warn of this low power pack condition for
at least 30 days. However, failure to change
the alarm after this time would mean your
smoke alarm may have insufcient power
to alert you in a real re situation. When the
alarm is removed from the base plate the
power pack will automatically deactivate
and the low power warning chirp will stop,
allowing you to dispose of the alarm.

EN
10 11
IMPORTANT: If your WST-630-NEU smoke
alarm enters a low power pack condition, it
will emit an audible “chirp” approximately
once every 45 seconds. All other
WST-630-NEU alarms in the network will
also emit an audible low battery chirp once
every 4 hours. This will continue until the
smoke alarm which has the low battery
condition is removed.
Fault Indication
If the amber LED ashes and an audible
‘chirp’ is heard at a different time, this
indicates that there is a fault; the unit may
not detect smoke and may not go into alarm
in the event of a re. If this occurs it is
strongly recommended that you replace the
alarm immediately.
Alarm Condition
If the WST-630-NEU goes into alarm, all
interlinked alarms will also sound 3 loud
beeps which continually repeat until the
cause of the alarm being activated is found
and resolved.The red LED will only ash
rapidly (once per second) on alarms that
have responded directly to smoke.
7. After completing the “learn-in” procedure,
test the alarms as described in “alarm
test”.
If any interlinked alarm fails to respond to
the “alarm test”, remove it from its base
plate and repeat the learning in process.
OPERATION
Normal Condition
The red LED on the front will ash
approximately every 45 seconds to show
that the alarm is active.
Low Power Pack Condition
IMPORTANT: Your smoke alarm requires
the power pack to have sufcient capacity
of power to operate correctly. Should your
FireAngel smoke alarm enter a low power
pack condition, the unit will emit an audible
‘chirp’ approximately once every 45 seconds
and the amber LED will ash at around the
same time. When this occurs it is strongly
recommended you replace the alarm
immediately and in any event within 30 days.
Your FireAngel smoke alarm will continue to
warn of this low power pack condition for
at least 30 days. However, failure to change
the alarm after this time would mean your
smoke alarm may have insufcient power
to alert you in a real re situation. When the
alarm is removed from the base plate the
power pack will automatically deactivate
and the low power warning chirp will stop,
allowing you to dispose of the alarm.

EN
12 13
ALARM TEST
a) Briey press the test button in the centre
and release.
b) The unit will give an audible alarm
consisting of 2 cycles of 3 loud beeps,
then stop automatically.
c) The red LED on the alarm will ash rapidly
during the audible signal.
NOTE: The test button tests the alarm’s
smoke sensing circuit. There is no need to
test your alarm with smoke. If your smoke
WST-630-NEU LED Indicators
Red LED Amber LED Audible
signal Status Action required
Flashes once
continuously
every 45 secs
Normal
operation
Flashes every
second
3 loud beeps
repeating Alarm Check if there is a re hazard and vacate property
Flashes once
every 45 seconds
3 loud beeps
repeating
Other
WST-630-NEUs in
network in alarm
Check if there is a re hazard and
vacate property
Flashes once
every 10 seconds
for up to 10 mins
“Smart silence”
Alarm has reduced
sensitivity
This will be as a result of you
silencing a false alarm. Sensitivity
will return to normal within 10 mins
Flashes once
every 45 seconds
Flashes at the same
time as the red LED
see note
Single chirp at the
same time as the
LED ash
Low
powerpack Replace within 30 days
Flashes once
every 45 seconds
Flashes once every 45
seconds, 20-25 seconds
after the red LED
Single chirp at the
same time as the
red LED ash
Fault
Call FireAngel Technical
support if within warranty. If not
replace alarm immediately
Flashes once
every 45 seconds
Single chirp every
four hours
Other alarm in
network has low
powerpack
Locate alarm with low powerpack
and replace
Flashes once
every 45 seconds
Double ashes at the
same time as the red
LED see note
Single chirp at the
same time as the
LED ash
Radio module low
battery
Call FireAngel Technical
support if within warranty. If not
replace alarm immediately
Flashes once
every 45 seconds
Double ashes every 45
seconds, 20-25 seconds
after the red LED
Single chirp at the
same time as the
red LED ash
Radio module fault
Call FireAngel Technical
support if within warranty. If not
replace alarm immediately
Note: The amber LED may ash twice on the WST-630-NEU, indicating that the fault is with the
wireless module. In this event, the complete WST-630-NEU alarm should be replaced.

EN
12 13
alarm fails to give an audible test signal,
please refer immediately to the trouble
shooting guide at the end of this manual.
WARNING: As with all electronic alarm
products you should test your smoke alarm
every week.
If your WST-630-NEU is interlinked with
other smoke alarms, we recommend that
every individual smoke alarm is tested
during the weekly test.
a) Briey press the test button in the centre
of the smoke alarm and release.
b) The unit you are testing will give an
audible alarm consisting of 2 cycles of
3 loud beeps, then stop automatically.
The red LED on this alarm will ash rapidly
(once per second) during the audible
alarm. All interlinked alarms will give an
audible alarm consisting of 2 cycles of
3 loud beeps, then stop automatically,
indicating the test is complete. The red
LED on all interlinked alarms will not ash
rapidly. If any alarm fails to self-test, see
Troubleshooting on page 16.
ALARM SMART
SILENCE™
DANGER: If your FireAngel smoke alarm emits
the full alarm signal and you are not testing
the unit, the smoke alarm is warning you of a
potentially dangerous situation that requires
your immediate attention. Only use the alarm
silence function after making sure that there
ALARM TEST
a) Briey press the test button in the centre
and release.
b) The unit will give an audible alarm
consisting of 2 cycles of 3 loud beeps,
then stop automatically.
c) The red LED on the alarm will ash rapidly
during the audible signal.
NOTE: The test button tests the alarm’s
smoke sensing circuit. There is no need to
test your alarm with smoke. If your smoke
WST-630-NEU LED Indicators
Red LED Amber LED Audible
signal Status Action required
Flashes once
continuously
every 45 secs
Normal
operation
Flashes every
second
3 loud beeps
repeating Alarm Check if there is a re hazard and vacate property
Flashes once
every 45 seconds
3 loud beeps
repeating
Other
WST-630-NEUs in
network in alarm
Check if there is a re hazard and
vacate property
Flashes once
every 10 seconds
for up to 10 mins
“Smart silence”
Alarm has reduced
sensitivity
This will be as a result of you
silencing a false alarm. Sensitivity
will return to normal within 10 mins
Flashes once
every 45 seconds
Flashes at the same
time as the red LED
see note
Single chirp at the
same time as the
LED ash
Low
powerpack Replace within 30 days
Flashes once
every 45 seconds
Flashes once every 45
seconds, 20-25 seconds
after the red LED
Single chirp at the
same time as the
red LED ash
Fault
Call FireAngel Technical
support if within warranty. If not
replace alarm immediately
Flashes once
every 45 seconds
Single chirp every
four hours
Other alarm in
network has low
powerpack
Locate alarm with low powerpack
and replace
Flashes once
every 45 seconds
Double ashes at the
same time as the red
LED see note
Single chirp at the
same time as the
LED ash
Radio module low
battery
Call FireAngel Technical
support if within warranty. If not
replace alarm immediately
Flashes once
every 45 seconds
Double ashes every 45
seconds, 20-25 seconds
after the red LED
Single chirp at the
same time as the
red LED ash
Radio module fault
Call FireAngel Technical
support if within warranty. If not
replace alarm immediately
Note: The amber LED may ash twice on the WST-630-NEU, indicating that the fault is with the
wireless module. In this event, the complete WST-630-NEU alarm should be replaced.

EN
14 15
also silence other alarms in the network.
However, any alarm that has sensed smoke
(an instigating alarm) cannot be remotely
silenced. This means that any alarm that
has sensed smoke will continue to sound
allowing you to locate it.
If any instigating alarm in the network has
not been silenced after a short period
(2-4 minutes), all other alarms will start
sounding again to alert you.
MAINTENANCE
Your FireAngel smoke alarm has been
designed to be as maintenance-free as
possible, however there are several things
you must do to keep it working properly.
CAUTION: Your FireAngel smoke alarm
is a sealed electrical device and no
attempt should be made to open the case.
Attempting to open the case will invalidate
your Warranty.
WARNING: This device contains a powerful
lithium battery. If tampered with , the battery
may be shorted and create a re hazard.
Never attempt to open or damage the
battery.
Testing
Test your smoke alarm once every week, see
section ‘Alarm Test’ on page 13. Any test
failures should be reported to the FireAngel
Technical Support Team see page 18.
is no re. Do not block the vents on the alarm
or disable the smoke alarm in any way, as this
will remove your protection. Smoke alarms can
sometimes react to cooking fumes or other
non-emergency situations.
Your smoke alarm features “Smart
Silence™” technology. In the event of a
known false alarm your smoke alarm can
be temporarily silenced by briey pressing
the central test button. Your alarm will
automatically return to full sensitivity within
10 minutes.
NOTE: If the level of smoke reaching the
alarm is very high the alarm silence will be
overridden and the alarm will continue to
sound.
1. Briey press and release the test button.
The alarm sound will soon stop.
2. Your alarm will silence and enter
into a reduced sensitivity mode for
approximately 10 minutes.
3. During the reduced sensitivity mode
the red LED on your alarm will continue
to ash more rapidly than normal,
approximately once every 10 seconds.
4.Your alarm will automatically return to full
sensitivity after a maximum of 10 minutes
and the red LED will revert to ashing
once every approximately 45 seconds.
DANGER: Never ignore any alarm. Ignoring
the alarm may result in injury or death. If
your smoke alarm activates and alarms and
you are not absolutely certain of the source
of the smoke, get everyone out of the house
immediately.
If your WST-630-NEU is interlinked with
other alarms, pressing the test button will

EN
14 15
also silence other alarms in the network.
However, any alarm that has sensed smoke
(an instigating alarm) cannot be remotely
silenced. This means that any alarm that
has sensed smoke will continue to sound
allowing you to locate it.
If any instigating alarm in the network has
not been silenced after a short period
(2-4 minutes), all other alarms will start
sounding again to alert you.
MAINTENANCE
Your FireAngel smoke alarm has been
designed to be as maintenance-free as
possible, however there are several things
you must do to keep it working properly.
CAUTION: Your FireAngel smoke alarm
is a sealed electrical device and no
attempt should be made to open the case.
Attempting to open the case will invalidate
your Warranty.
WARNING: This device contains a powerful
lithium battery. If tampered with , the battery
may be shorted and create a re hazard.
Never attempt to open or damage the
battery.
Testing
Test your smoke alarm once every week, see
section ‘Alarm Test’ on page 13. Any test
failures should be reported to the FireAngel
Technical Support Team see page 18.
Cleaning
As a minimum your smoke alarm should be
cleaned once every 3 months using your
vacuum cleaner tted with the soft brush
attachment.
WARNING: Your FireAngel smoke alarm
may false alarm when it is being cleaned
using a vacuum cleaner.
IMPORTANT: Do not use solvents or
cleaners on your FireAngel smoke alarm,
as they may cause damage to the sensor
or circuitry. The unit can be wiped with a
slightly damp cloth.
CAUTION: Do not paint the smoke alarm
as this may block the openings and prevent
smoke from entering the sensor.
WARNING: If any alarm in the network is
sounding, it is warning you of a potentially
hazardous situation. Do not ignore it.
3. During the reduced sensitivity mode
the red LED on your alarm will continue
to ash more rapidly than normal,
approximately once every 10 seconds.
4.Your alarm will automatically return to full
sensitivity after a maximum of 10 minutes
and the red LED will revert to ashing
once every approximately 45 seconds.
DANGER: Never ignore any alarm. Ignoring
the alarm may result in injury or death. If
your smoke alarm activates and alarms and
you are not absolutely certain of the source
of the smoke, get everyone out of the house
immediately.
If your WST-630-NEU is interlinked with
other alarms, pressing the test button will

EN
16 17
Problem Solution
Your FireAngel smoke alarm
chirps intermittently
• Check the location of your smoke alarm (see ‘Application’
and ‘Positioning’)
• Check that your smoke alarm is denitely the source of
chirping; make sure the noise isn’t coming from another
alarm (smoke/carbon monoxide/burglar/gas alarm) by
process of elimination.
• If the alarm is chirping once approximately every
45 seconds and the amber led is ashing around the same
time, it indicates that the power pack is low. The unit
should be replaced within 30 days.
• If your smoke alarm is chirping once every 4 hours, it is
indicating that another alarm in the network has entered
a low power pack condition. Locate the alarm with the
low battery condition and replace the alarm as soon as
possible and in any event within 30 days.
Your FireAngel smoke alarm
activates when no smoke
is visible
• Check the location of your smoke alarm (see the section
on ‘Positioning’).
• Clean the smoke alarm (see the section on ‘Maintenance’).
• If the alarm is sounding but the red LED is only ashing
approximately once every 45 seconds, this indicates that
an inter-linked alarm has detected smoke. Vacate property
if there is a re hazard.
Other interlinked units fail
to silence when one unit is
silenced
• Interlinked units that have sensed smoke can’t be silenced.
If one or more unit remains in alarm, all other interlinked
units will emit their audible warning again within 4 minutes.
Vacate property if there is a re hazard.
TROUBLESHOOTING
Problem Solution
Your FireAngel smoke alarm
does not sound during
testing
• Make sure the alarm has been rotated clockwise as far as
it can go and is securely located on its base plate.
• If testing immediately after rst activating the alarm, you
should allow a few seconds for the alarm to settle before
testing.
• Make sure you push the centre of the test button rmly.
• If the unit has been silenced and is in low sensitivity mode
it may not test. Wait 15 minutes then try again.
• If the alarm has been recently tted and it still fails to self
test then contact technical support (see page 18).
• Check positioning. The wireless signal might be blocked or
out of range.
• If you are in the process of learning in the alarm and does
not test – repeat the process.
• If the alarm still fails to self test, please contact technical
support (see page 18).
Your FireAngel smoke alarm
cannot be removed from its
base plate
If you nd that you cannot remove the smoke alarm from its
base plate, the locking mechanism may have been engaged.
Undue force may result in damage to the smoke alarm or
the base plate or both. For more information contact your
installer, or contact FireAngel Technical Support Team between
9am - 5pm Monday – Friday. E-mail: support@reangel.eu
or telephone: DK: 0800 711 151 / FI: 0880 055 2130 /
NO: 0800 69 127 / SE: 0200 123 598.

EN
16 17
Problem Solution
Your FireAngel smoke alarm
chirps intermittently
• Check the location of your smoke alarm (see ‘Application’
and ‘Positioning’)
• Check that your smoke alarm is denitely the source of
chirping; make sure the noise isn’t coming from another
alarm (smoke/carbon monoxide/burglar/gas alarm) by
process of elimination.
• If the alarm is chirping once approximately every
45 seconds and the amber led is ashing around the same
time, it indicates that the power pack is low. The unit
should be replaced within 30 days.
• If your smoke alarm is chirping once every 4 hours, it is
indicating that another alarm in the network has entered
a low power pack condition. Locate the alarm with the
low battery condition and replace the alarm as soon as
possible and in any event within 30 days.
Your FireAngel smoke alarm
activates when no smoke
is visible
• Check the location of your smoke alarm (see the section
on ‘Positioning’).
• Clean the smoke alarm (see the section on ‘Maintenance’).
• If the alarm is sounding but the red LED is only ashing
approximately once every 45 seconds, this indicates that
an inter-linked alarm has detected smoke. Vacate property
if there is a re hazard.
Other interlinked units fail
to silence when one unit is
silenced
• Interlinked units that have sensed smoke can’t be silenced.
If one or more unit remains in alarm, all other interlinked
units will emit their audible warning again within 4 minutes.
Vacate property if there is a re hazard.
TROUBLESHOOTING
Problem Solution
Your FireAngel smoke alarm
does not sound during
testing
• Make sure the alarm has been rotated clockwise as far as
it can go and is securely located on its base plate.
• If testing immediately after rst activating the alarm, you
should allow a few seconds for the alarm to settle before
testing.
• Make sure you push the centre of the test button rmly.
• If the unit has been silenced and is in low sensitivity mode
it may not test. Wait 15 minutes then try again.
• If the alarm has been recently tted and it still fails to self
test then contact technical support (see page 18).
• Check positioning. The wireless signal might be blocked or
out of range.
• If you are in the process of learning in the alarm and does
not test – repeat the process.
• If the alarm still fails to self test, please contact technical
support (see page 18).
Your FireAngel smoke alarm
cannot be removed from its
base plate
If you nd that you cannot remove the smoke alarm from its
base plate, the locking mechanism may have been engaged.
Undue force may result in damage to the smoke alarm or
the base plate or both. For more information contact your
installer, or contact FireAngel Technical Support Team between
9am - 5pm Monday – Friday. E-mail: support@reangel.eu
or telephone: DK: 0800 711 151 / FI: 0880 055 2130 /
NO: 0800 69 127 / SE: 0200 123 598.

EN
18 19
DISPOSAL
Waste electrical products should not be disposed
of with your other household waste. Unlike
ionisation smoke alarms your Thermoptek alarm
does not contain any radioactive material. This
means that the alarm is ideally suited for disposal
within the waste electronic and electrical equipment
(WEEE) recycling scheme. Please recycle where
facilities exist. Check with your local authority,
retailer or contact our technical support team for
recycling/disposal advice as regional variations
apply. Once the alarm is removed from the base
plate the internal power pack (battery) will be
deactivated. The unit is now ready for disposal.
WARNING: Do not attempt to open.
WARNING: Do not burn or dispose of in re.
WARNING: If your smoke alarm is dropped or
damaged, as a precaution, it should be removed
from the building and you should contact FireAngel
Technical Support on support@reangel.eu or
telephone: DK: 0800 711 151 / FI: 0880 055 2130 /
NO: 0800 69 127 / SE: 0200 123 598.
WARRANTY
Sprue Safety Products Ltd warrants to the original
purchaser that its enclosed smoke alarm be free
from defects in materials and workmanship under
normal residential use and service for a period of
5 (ve) years from the date of purchase. Provided
it is returned with postage prepaid and proof of
purchase date, Sprue Safety Products Ltd hereby
warrants that during the 5 (ve) year period
commencing from the date of purchase Sprue
Safety Products Ltd, at its discretion, agrees to
replace the unit free of charge. The warranty on any
replacement WST-630-NEU alarm, will last for the
remainder of the period of the original warranty in
respect of the alarm originally purchased – that is
Problem Solution
You experience frequent
unwanted alarms
• Check the location of your FireAngel smoke alarm (see the
section on ‘Positioning’).
• Clean the smoke alarm (see the section on ‘Routine
Maintenance’).
• Any activated alarm will cause other interlinked alarms to
sound. Carry out these checks on the activated alarms in
particular (red LED ashing rapidly during alarm).
• If the frequent unwanted alarms continue contact technical
support for advice.
The amber LED is ashing
and the alarm is making a
“chirping” sound
• If the amber LED is ashing at around the same time as
the chirp, this indicates a low power pack condition and
the alarm should be replaced as soon as possible and
certainly within 30 days.
• If the amber LED is ashing at a different time to the chirp,
this indicates a fault and the alarm should be replaced as
soon as possible.
• If the amber LED is double ashing and the alarm is
making a “chirping” sound, this indicates that the wireless
module has a low power pack condition, or is faulty. The
alarm should be replaced as soon as possible.
If the alarm fails to operate
correctly, the advice of the
manufacturer should be
sought
If you have any questions about the operation of your alarm,
you can visit the support section of our website
www.reangel.eu or telephone the FireAngel Technical
Support Team between 9am - 5pm Monday – Friday.
Telephone: DK: 0800 711 151 / FI: 0880 055 2130 /
NO: 0800 69 127 / SE: 0200 123 598.

EN
18 19
DISPOSAL
Waste electrical products should not be disposed
of with your other household waste. Unlike
ionisation smoke alarms your Thermoptek alarm
does not contain any radioactive material. This
means that the alarm is ideally suited for disposal
within the waste electronic and electrical equipment
(WEEE) recycling scheme. Please recycle where
facilities exist. Check with your local authority,
retailer or contact our technical support team for
recycling/disposal advice as regional variations
apply. Once the alarm is removed from the base
plate the internal power pack (battery) will be
deactivated. The unit is now ready for disposal.
WARNING: Do not attempt to open.
WARNING: Do not burn or dispose of in re.
WARNING: If your smoke alarm is dropped or
damaged, as a precaution, it should be removed
from the building and you should contact FireAngel
Technical Support on support@reangel.eu or
telephone: DK: 0800 711 151 / FI: 0880 055 2130 /
NO: 0800 69 127 / SE: 0200 123 598.
WARRANTY
Sprue Safety Products Ltd warrants to the original
purchaser that its enclosed smoke alarm be free
from defects in materials and workmanship under
normal residential use and service for a period of
5 (ve) years from the date of purchase. Provided
it is returned with postage prepaid and proof of
purchase date, Sprue Safety Products Ltd hereby
warrants that during the 5 (ve) year period
commencing from the date of purchase Sprue
Safety Products Ltd, at its discretion, agrees to
replace the unit free of charge. The warranty on any
replacement WST-630-NEU alarm, will last for the
remainder of the period of the original warranty in
respect of the alarm originally purchased – that is
from the date of original purchase and not from the
date of receipt of the replacement product. Sprue
Safety Products Ltd reserves the right to offer an
alternative product similar to that being replaced if
the original model is no longer available or in stock.
This warranty applies to the original retail purchaser
from the date of original retail purchase and is not
transferable. Proof of purchase is required. This
warranty does not cover damage resulting from
accident, misuse, disassembly, abuse or lack of
reasonable care of the product, or applications
not in accordance with the user manual. It does
not cover events and conditions outside of Sprue
Safety Products Ltd’s control, such as Acts of
God (re, severe weather etc.). It does not apply
to retail stores, service centres or any distributors
or agents. Sprue Safety Products Ltd will not
recognise any changes to this warranty by third
parties.
Sprue Safety Products Ltd shall not be liable for
any incidental or consequential damages caused
by the breach of any expressed or implied warranty.
Except to the extent prohibited by applicable law,
any implied warranty of merchantability or tness
for a particular purpose is limited in duration for
5 (ve) years. This warranty does not affect your
statutory rights. Except for death or personal injury,
Sprue Safety Products Ltd shall not be liable for
any loss of use, damage, cost or expense relating
to this product or for any indirect or consequential
loss, damages or costs incurred by you or any
other user of this product.
Problem Solution
You experience frequent
unwanted alarms
• Check the location of your FireAngel smoke alarm (see the
section on ‘Positioning’).
• Clean the smoke alarm (see the section on ‘Routine
Maintenance’).
• Any activated alarm will cause other interlinked alarms to
sound. Carry out these checks on the activated alarms in
particular (red LED ashing rapidly during alarm).
• If the frequent unwanted alarms continue contact technical
support for advice.
The amber LED is ashing
and the alarm is making a
“chirping” sound
• If the amber LED is ashing at around the same time as
the chirp, this indicates a low power pack condition and
the alarm should be replaced as soon as possible and
certainly within 30 days.
• If the amber LED is ashing at a different time to the chirp,
this indicates a fault and the alarm should be replaced as
soon as possible.
• If the amber LED is double ashing and the alarm is
making a “chirping” sound, this indicates that the wireless
module has a low power pack condition, or is faulty. The
alarm should be replaced as soon as possible.
If the alarm fails to operate
correctly, the advice of the
manufacturer should be
sought
If you have any questions about the operation of your alarm,
you can visit the support section of our website
www.reangel.eu or telephone the FireAngel Technical
Support Team between 9am - 5pm Monday – Friday.
Telephone: DK: 0800 711 151 / FI: 0880 055 2130 /
NO: 0800 69 127 / SE: 0200 123 598.

DK
20 21
Indledning . . . . . . . . . . . . 21
Automatisk strømforsyning . . . 21
Sensorteknologi . . . . . . . . . 21
Thermoptek sensor teknologi . . 22
Anvendelse. . . . . . . . . . . . 22
Placering . . . . . . . . . . . . . 23
Hvordan røgalarmen monteres. . 25
Serieforbindelse
af WST-630-NEU . . . . . . . . . 26
BEMÆRK: Denne brugsvejledning fås også med stor skrift og i
andre formater. Ring venligst på 0800 711 151 for at få yderligere
information.
Drift. . . . . . . . . . . . . . . . 27
WST-630-NEU LED indikatorer . 29
Alarmtest . . . . . . . . . . . . . 30
Alarm Smart Silence™ . . . . . . 30
Vedligeholdelse . . . . . . . . . 32
Problemløsning. . . . . . . . . . 33
Bortskaffelse . . . . . . . . . . . 36
Garanti . . . . . . . . . . . . . . 36
INDHOLD INDLEDNING
FireAngel WST-630-NEU trådløs,
serieforbundet, multi-kriterier, højt ydende
detektor er det ultimative alternativ til
traditionelle alarmer. Banebrydende
Thermoptek teknologi kombinerer det sidste
nye inden for optiske sensorer med termisk
forstærkning, hvilket giver hurtig respons
på både hurtigt opammende og langsomt
ulmende brande og fjerner behovet for
ioniseringskilder, som kan være skadelige
for miljøet.
Op til maksimalt 50 WST-630-NEU kan
serieforbindes trådløst og danne et netværk.
Hvis en røgalarm går i gang, får den alle
andre alarmer i dens netværk til at gå i gang
på samme tid. Dette giver den tidligst mulige
advarsel om en brand.
Alarmsignaler går gennem alle WST-630'ere
i netværket, og forøger netværkets
rækkevidde og pålidelighed.
VIGTIGT: Denne brugsvejledning indeholder
vigtige oplysninger om drift af din FireAngel
røgalarm. Sørg for at læse hele denne
brugsvejledning før montering og brug
af alarmen. Hvis du monterer denne
røgalarm til brug for andre, skal du efterlade
denne vejledning (eller en kopi af den) til
slutbrugeren.
Den originale engelske version af manualen, som denne oversættelse er taget
fra, har fået en selvstændig godkendelse. I tilfælde af uoverensstemmelse
med oversatte dele bekræfter Sprue Safety Products Ltd, at den engelske
vejledning er sand og korrekt.