Fireplacextrordinair 42 apex clean face User manual

+



42 Apex Clean Face

Installation Manual

12521 Harbour Reach Drive

Mukilteo, WA 98275

This manual is available online in French.

Manuel est disponible en ligne en Francais.

www.travisproducts.com

Wood-Burning

Zero-Clearance

Fireplace

$10.00 100-01450

Report # 028WF102S

U.L. 127-2015 and ULC-S610-M87

(R1998)

2 Introduction

Overview

This manual details the installation requirements for the 42 Apex Clean Face (CF) wood-burning

fireplace. For operating and maintenance instructions, refer to the 42 Apex CF Owner's Manual.

Keep this manual for future use.

Listing Details

This appliance was listed by OMNI Test Labs to U.L. 127 and ULC-S610-M87 – report number

028WF102S. The listing label is attached to the base of the fireplace and can be viewed by accessing the

fan compartment.

DO NOT REMOVE THIS LABEL

CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT INSTALLATION AND

RESTRICTIONS IN YOUR AREA. LISTED FACTORY-BUILT FIREPLACE

Report No. 028WF102S

Certified for USA and Canada

Tested and

Listed by

®

MODEL:

42 Apex

SERIAL NO:

CONFORMS TO UL STD 127-2015; CERTIFIED TO ULC STD S610-M87 (R1998)

This wood heater needs periodic inspection and repair for proper operation. Consult the owner’s manual for further information. It is against federal regulations to operate this wood heater in a manner

inconsistent with operating instructions in the owner’s manual or if the catalytic element is deactivated or removed. CAUTION: the combustor used in this appliance (part no. 250-00556) is fragile and must

be handled carefully. Burning of metal foils, plastic, garbage, sulphur and diesel oil will render the catalyst in the combustor inactive. The performance and durability of the catalytic combustor has not

been evaluated as part of the certification. Do not use a fireplace insert or other products not specified for use with this product. This fireplace has not been tested with an unvented gas log set. To reduce

the risk of fire or injury, do not install an unvented gas log set into fireplace. Fireplace must use combustion air drawn from outside the house. Use cord wood only. DO NOT OVERFIRE UNIT.

See Installation Manual for approved chimneys

Replace glass only with 5mm neoceramic or

ceramic glass.

Electrical Rating: 115V., 60 Hz, 1.8 Amps

Optional Green Start: # 94400954

Blower: # 250-04176

TRAVIS INDUSTRIES, INC.

12521 Harbour Reach Drive

Mukilteo, WA 98275

Manufactured by:

www.travisproducts.com

U.S. ENVIRONMENTAL PROTECTION AGENCY

Certified to comply with 2015 particulate emission standards. Not approved for sale after May 15, 2020.

0.7 g/h, Method 28, 5G2, 2015

Made in U.S.A.

2017 2018 2019 2020 Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec

DATE OF MANUFACTURE

1212

®

42 Apex

Serial

No. ZC-1203

MANUFACTURE DATE:

2017

2018

2016

FEB

MAR

JAN

MAY

JUN

APR

AUG

SEP

JUL

NOV

DEC

OCT

U.S. ENVIRONMENTAL PROTECTION AGENCY

Certified to comply with 2015 particulate emission standards. Not approved for sale after May 15, 2020.

0.7 g/h, Method 28, 5G2, 2015

This wood heater contains a catalytic combustor which needs periodic inspection and replacement for proper operation.

Consult the owner’s manual for further information. It is against federal regulations to operate this wood heater in a manner

inconsistent with operating instructions in the owner’s manual or if the catalytic element is deactivated or removed. See

installation and operating instructions for this model. Use cord woood only.

Manufactured By: TRAVIS INDUSTRIES, INC.

12521 Harbour Reach Drive, Mukilteo, WA 98275

XXXX

IAS (ICBO) Approval

This appliance was listed by OMNI Test Labs – IAS (ICBO) # TL-130.

EPA Approval

This heater meets the 2015 U.S. EPA’s crib wood emission limits for wood heaters sold after May 15,

2015. Tested to Method 28, 5G2 this heater has been shown to deliver 11,000 to 38,000 BTUs/hr and an

emission value of .69 g/h.

This wood heater has a manufacturer-set minimum low burn rate that must not be altered. It is against

federal regulations to alter this setting or otherwise operate this wood heater in a manner inconsistent

with operating instructions in this manual.

National Fireplace Institute

Table of Contents 3

Overview..........................................................................2

Listing Details...................................................................2

IAS (ICBO) Approval ....................................................2

EPA Approval...............................................................2

National Fireplace Institute...........................................2

Installation Warnings ....................................................4

Operating Warnings......................................................4

Installation Options...........................................................5

Heating Specifications......................................................5

Dimensions ......................................................................5

ITEMS UNIQUE TO THIS FIREPLACE...........................6

Framing the Chase

.....................................................................................Err

or! Bookmark not defined.

The Chase (fireplace enclosure) Must Be Ventilated....6

Air-Cooled Chimneys Offsets Inside Chase Must Be

Directed to the Rear to Clear Manifold..........................6

Packing List......................................................................7

Recommended Order of Installation.................................7

Installation Recommendations for Cold Environments.....8

Insulated Chimney is Strongly Recommended.............8

Use “P” Trap & Insulated Duct in the Cooling Duct.......8

Use Bi-Metallic Damper with Air-Cooled Chimney........8

Use Outside Air “P” Trap and Insulated Duct................8

Daily Requirements for Homeowners ...........................8

OTHER ITEMS.........................................................8

Fireplace Placement Requirements .................................9

Clearances to Fireplace................................................9

Fireplace Placement.....................................................10

Minimum Framing Dimension...........................................11

Framing Dimensions at 45°..............................................12

Convection Air Manifold ...................................................13

Chase Ventilation (REQUIRED).......................................14

Chase Ventilation Overview..........................................14

Chase Ventilation Grills ................................................15

Dimensions...............................................................15

Chase Ventilation – Front Configuration.......................16

Chase Ventilation – Side Configuration........................17

Raised Fireplaces.............................................................18

Approved Chimney...........................................................19

Air Cooled Chimney Requirements (8” Inner Dia., 12” Outer

Dia.)..................................................................................20

Part Numbers (available through Travis Industries)......20

Anchor Plate Installation...............................................20

Cooling Duct Installation...............................................21

Air Cooled Chimney - Clearances to Combustibles......22

Air Cooled Chimney – Use of Offsets in Chase............23

Air Cooled Chimney – Installation and System Height .24

Air Cool Chimney - Offset Requirements (30° Elbows) 25

Firestops ......................................................................25

Chimney Offset Chart...................................................25

Insulated Chimney Requirements (7” Inner Diameter).....26

Security ASHT+ (S2100+) Part Numbers (available

through Travis Ind.)......................................................26

Security ASHT+ - Clearances to Combustibles........26

Security ASHT+– Anchor Plate Installation ..............26

Security ASHT+– Offset Chart .................................26

Insulated Chimney – Alternative Manufacturers...........27

Anchor Plate Installation...........................................27

Insulated Chimney – Installation and System Height....28

Insulated Chimney - Offset Requirements (30° Elbows)

.....................................................................................29

Firestops ......................................................................29

Chimney Termination Requirements................................30

Convection Air Manifold and Non-Combustible Framing..31

Contents of Framing Hardware Box.............................31

Contents Strapped to Exterior of Fireplace & Inside

Firebox.........................................................................32

Steps for Installing the Convection Air Manifold...........33

Upper Manifold Trim.....................................................35

Steps for Installing the Non-Combustible Framing.......36

Electrical Line Hookup .....................................................38

Wiring Diagram.............................................................38

Fireplace Junction Box.................................................39

Inside of Junction Box..................................................39

External Wiring Installation...............................................40

External Wiring Installation (continued)............................41

Back Side of the Combustor Temp Display..................41

Air Intake Installation........................................................42

Air Intake Locations......................................................43

Facing Requirements.......................................................44

Facing Requirements (continued)....................................45

Mantel Requirements.......................................................46

Hearth Requirements.......................................................47

Finalizing the Installation..................................................48

Index ............................................................................50

4 Safety Precautions

Installation Warnings

Read this entire manual before installing the fireplace.

Failure to install this fireplace in accordance with all local codes and the requirements listed in this

manual may result in property damage, bodily injury, or even death.

Notify your insurance company before installing this fireplace.

Contact your local building officials to obtain a permit and information on installation restrictions or

inspection requirements in your area.

Notify your insurance company of this fireplace.

The requirements listed below are divided into sections. All requirements must be met

simultaneously. The order of installation is not rigid – the qualified installer should follow the

procedure best suited for the installation.

Modifications of the fireplace (doors, air inlet systems, damper control, or any other component

supplied by Travis Industries) or use of any component part not approved by Travis Industries in

combination with this fireplace system will void the listing and warranty.

This fireplace is not approved for use in a mobile home.

Travis Industries, Inc. grants no warranty, implied or stated, for the installation or

maintenance of your heater, and assumes no responsibility of any consequential damage(s).

Operating Warnings

WARNING: FIREPLACE SHOULD BE OPERATED ONLY WITH DOORS FULLY OPEN OR DOORS

FULLY CLOSED. IF DOORS ARE LEFT PARTLY OPEN, GAS AND FLAME MAY BE DRAWN OUT

OF THE FIREPLACE OPENING, CREATING RISKS OF BOTH FIRE AND SMOKE.

Creosote – Formation and Need for Removal

When wood is burned slowly it produces tar and other organic vapors which combine with expelled

moisture to form creosote. The creosote vapors condense in the relatively cool chimney flue of a

slow-burning fire. As a result, creosote residue accumulates on the flue lining. When ignited this

creosote makes an extremely hot fire.

The chimney shall be inspected at least twice a year during the heating season to determine when a

creosote buildup has occurred.

When creosote has accumulated it shall be removed to reduce the risk of a chimney fire.

Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter fluid, or similar liquids to

start or ‘freshen up’ a fire in this fireplace. Keep all such liquids well away from the fireplace while it is

in use.

Disposal of Ashes

Ashes should be placed in a metal container with a tight-fitting lid. The closed container of ashes

should be placed on a noncombustible floor or on the ground, well away from all combustible

materials, pending final disposal. If the ashes are disposed of by burial in soil or otherwise locally

dispersed, they should be retained in the closed container until all cinders have thoroughly cooled.

A fireplace insert shall not be installed in a factory-built fireplace unless tested with the fireplace.

Proposition 65 Warning: Fuels used in gas, woodburning or oil fired appliances, and the products of combustion of such fuels,

contain chemicals known to the State of California to cause cancer, birth defects and other reproductive harm.

California Health & Safety Code Sec. 25249.6

Travis Wood Burning Fireplaces, Stoves and Inserts are protected by one or more of the following patents; U.S. 9,170,025,

4,665,889 as well as other U.S. and Foreign Patents pending.

Features and Specifications 5

Installation Options

Residential (not approved for HUD Mobile Homes)

Straight or Corner Placement

Raised or Floor Placement

Raised or Floor Hearth

Internal or External Chase

5 Air Intake Locations

1 Electrical Connection Location

Heating Specifications

Approximate Heating Capacity (in square feet)*.................. Up to 2,500 sq. ft.

Maximum Burning Time........................................................ Up to 12 Hours

BTU Output per Hour (Cord Wood Method)......................... Up to 62,000 BTUs

* Heating capacity will vary with floor plan, insulation, and outside temperature.

Dimensions

42"*

1067mm*

Optional Front Inlet

Knock-Outs

22-7/8"*

582mm*



Weight = 670 lbs. (304 Kg)

* Includes the 1/2" (13mm) stand-offs

3" (77mm) Air Intake

(may be re-routed to

left, back or bottom)



47-1/4"

1201mm

Electrical Input &

External Control

Junction Box



26"

661mm

1-1/8"

29mm



10-1/8"*

258mm*

Convection Air Outlet

(attach lower manifold to

this duct opening)

Side Inlets

38"

966mm



9-5/8"

245mm

6 Installation (for qualified installers only)

ITEMS UNIQUE TO THIS FIREPLACE

Header Height is Determined

by the Convection Air Outlet

The height of the convection air

outlet determines the framing

header height (see illustration to

the right and page 13 for details).

The desired outlet height should

be determined prior to framing.

Make sure all minimum

clearances are maintained.

42 Apex CF

Fireplace



Min. 3-1/2"

Lower Framing (included)

Upper Convection Manifold

6-1/2" *



Max. 116-1/2"

Min. 78-1/2" **

Lower Convection Manifold

5" Alum. Flex Duct (included)

Framing Header

Celing

Convection Air Outlet

Upper Framing (included)

The Chase (fireplace enclosure)

Must Be Ventilated

The chase (fireplace enclosure) must be

ventilated to provide proper fireplace

cooling (see illustration to the right and

page 14 for details). Grills are included

for this purpose.

If ventilated to the sides, a minimum 2” air

space is required(see illustration below

and page 17 for details). The framing

may need to be altered to provide proper

ventilation.

MIn. 2"

Max.. 5-1/2"

This shaded area on both sides of the fireplace must be left

unobstructed when using the side chase ventilation configuration.

TOP OF FIREPLACE









b

ca

a

Air-Cooled Chimneys Offsets Inside Chase Must Be Directed to the Rear to Clear Manifold

When using offsets inside the chase the offsets will need to be angled back slightly to allow the chimney to clear

the upper manifold (see page 23). In most installations this offset will need to be angled back 1-1/2”.

Installation (for qualified installers only) 7

Packing List

NOTE: The log stop is secured for shipping with a set screw on the back of the log stop support. Loosen

the set screws with a 1/8” hex wrench and remove the log stop to access the internal

components.

Bricks (2 boxes – left side and right side)

Baffle

Air Intake Parts (10’ of 3” diameter duct,

intake hood, hood bezel, and 2 hose clamps)

Ember strip

Switch Plate with Combustor Temp. Display

and Rheostat

Door Tool

Manifold / Non-Combustible Framing Parts

Face (ships pre-attached to the fireplace)

Owner’s manual

Pair of gloves

Upper Manifold Trim

Front Ventilation Grill

Small Ventilation Grills

5” Aluminum Flex Duct

Recommended Order of Installation

Frame the opening for the fireplace. Leave the non-combustible framing and facing above the

fireplace open to allow for chimney installation.

Secure the fireplace to the framing/floor.

Install the chimney (and cooling air, if applicable), electrical, external wiring (rheostat, catalytic temp

reader, etc.), and outside air.

Install the Convection Air Manifold and non-combustible framing – see “Convection Air Manifold

Installation”.

Install the ventilation grills used for chase ventilation

Install the hearth (if applicable)

Install the non-combustible facing.

Install the non-combustible mantel (if applicable).

Finalize the installation/

8 Installation (for qualified installers only)

Installation Recommendations for Cold Environments

If you live in the area depicted in black in the illustration to the

right (or in Canada), we recommend the following steps be

taken to minimize cold air infiltration.

Insulated Chimney is Strongly Recommended

Insulated chimney does not require cooling ducts and is

therefore preferred for cold environments. This is the

number one method for improving cold weather performance.

Use “P” Trap & Insulated Duct in the Cooling Duct.

If using air-cooled chimney, we recommend insulating the

intake duct and putting in a “P” trap to help prevent air

circulation when the fireplace is not in use. A typical “P” trap

design is shown in the illustration to the right.

Use Bi-Metallic Damper with Air-Cooled Chimney

If using air-cooled chimney, we recommend the use of the bi-

metallic damper. This component (part # 250-01741) is an 18”

section of Duravent pipe that is installed at the top of the

chimney, directly below the cap. It has a heat-activated damper

that helps reduce cold air from entering the cooling ducts while

the fireplace is not in operation.

Use Outside Air “P” Trap and Insulated Duct



Min. 24"

Max. 48"

Min. 24"

Max. 48"

42 Apex Fireplace

We recommend putting in a “P” trap in the outside air duct (used to supply air to the firebox) to prevent air

circulation when the fireplace is not in use. A typical “P” trap design is shown in the illustration above. In

addition, you should insulate the outside air duct to help reduce air circulation when the fireplace is not in

use.

Daily Requirements for Homeowners

HUMIDITY – If the home is equipped with a humidistat, make sure it is set correctly. The chart below

details the correct setting for the temperature you are experiencing outdoors.

Outdoor Temperature Recommended Humidity Controller

Setting

°F °C

-20 -29 15

-10 -23 20

0 -18 25

+10 -12 30

+20 -7 35

>+20 >-7 40

Note: If using a humidifier, let the homeowner know that it should be shut off or turned to a lower setting

to eliminate condensation on the front of the fireplace.

OTHER ITEMS

Make sure the bypass is shut when the fireplace is not in use.

Slide the air control fully closed when fireplace is not in use.

Minimize the use of exhaust fans in the home when the fireplace is not in use.

Installation (for qualified installers only) 9

Fireplace Placement Requirements

Clearances to Fireplace

Sidewalls to the front of the fireplace must be 45” (1143mm) from the centerline of the fireplace (see

“a” in the illustration below).

Any combustible (bookshelf, column, etc.) that protrudes less than 7” (178mmmm) from the front of

the fireplace must be placed a minimum 24-3/8” (620mmmm) from the centerline of the fireplace. If

this combustible protrudes farther, it must meet the sidewall clearance (see “b” and “c” in the

illustration below).





ab

cd

The fireplace requires a ½” (13mm) clearance to the back and sides (stand-offs are pre-installed to

provide this clearance). Do not place insulation or other material into this area. Drywall or other

combustibles must maintain a ½” clearance to the sides of the fireplace (see “d” in the illustration

above).

Fireplace should be located such that no doors, drapes, furniture or other combustibles can be

placed close or swing closer than the minimum 48" clearance. Due to the high heat output of this

fireplace, choose a location away from high traffic areas.

10 Installation (for qualified installers only)

Fireplace Placement

The fireplace must be secured to the floor and/or framing (see “nailing brackets” in the illustration

below).

Fireplace must be placed directly on wood or non-combustible surface (not on linoleum or carpet).

Fireplace must be installed on a level surface capable of supporting the fireplace and chimney.

Place the ember strip included with the fireplace below the front edge of the fireplace (see illustration

below). This prevents embers from sliding between the fireplace and hearth.

Fireplace must be placed so the vents below and above the glass do not become blocked.

We rcommend the chase around

the fireplace be insulated.

WARNING:

Insulation must be secured so it

does not fill the space between

the fireplace and standoffs.

Base Nailing Brackets

(bend down and secure to floor)

Lifting handles are available separately (98500711).

They attach to the base nailing brackets.

Standoffs

(on sides and back)

Side Nailing Brackets

(secure to side framing)



Center the ember strip below the front edge of the

fireplace and secure it to the floor.

The fireplace must be level and plumb

during installation. Use shims under the

fireplace to properly level the fireplace if

needed.

Fireplace

WARNING:

Failure to correctly level and plumb the

fireplace may lead to the door swinging

open or closed.

Installation (for qualified installers only) 11

Minimum Framing Dimension

FRAMING HEIGHT

Framing height is determined by the height of the upper convection air manifold. See the section

“Convection Air Manifold” for details.

Minimum framing dimensions are shown in the illustration below. Do not build into the enclosure.

116-1/2"

to

78-1/2"

23"

585mm

42"

1067mm

Min. Ceiling or Enclosure Height = 3-1/2" above framing header.

Max. Header

Depth = 3-1/2"

The enclosure over the fireplace must be a minimum 3-1/2” (89mm) above the framing header.

The ceiling in front of fireplace must be a minimum 3-1/2” (89mm) above the framing header (min. 10”

above the manifold outlet).

NOTE: The enclosure circulates room air. We recommend dry-walling the interior of the enclosure or

using suitable means to prevent dust or building debris from being circulated into the room. MAKE

SURE TO ADD AN ADDITIONAL ½” TO THE DEPTH/WIDTH IF USING DRYWALL.

The fireplace enclosure (chase) conveys room air. This area must be insulated and drywall applied if

on an exterior wall.

12 Installation (for qualified installers only)

Framing Dimensions at 45°

Typical framing dimensions

for 45° installation are

shown below. Additional

space may be required for

vent and outside air

installation.

(a) 61-3/4” (1569mm)

(b) 22-1/2” (572mm)

(c) 22-1/2” (572mm)





c



Fireplace

(includes 1/2" standoffs)

a

b

1/2" Clearance to Corners

Installation (for qualified installers only) 13

Convection Air Manifold

The convection air manifold is assembled on site and attached to the top of the fireplace. It directs

the hot convection air out of the fireplace and into the room.

42 Apex CF

Fireplace



Min. 3-1/2"

Lower Framing (included)

Upper Convection Manifold

6-1/2" *



Max. 116-1/2"

Min. 78-1/2" **

Lower Convection Manifold

5" Alum. Flex Duct (included)

Framing Header

Celing

Convection Air Outlet

Upper Framing (included)

* When using the included upper framing members the manifold outlet will be 6-1/2” below the header.

This is the most common installation, placing the outlet at the tallest position. If you wish to make this

dimension lower, you may supply longer pieces of non-combustible framing to place the outlet in a

lower position.

** When the header is placed between 116-1/2” and 92-1/2” above the base of the fireplace, the

supplied lower framing members are installed without modification. If you wish to place the header

between 92-1/2” and 78-1/2”, the lower framing members will need to be cut down in length (use

hack saw, nail-clippers, etc.).

14 Installation (for qualified installers only)

Chase Ventilation (REQUIRED)

WARNING: The chase must be ventilated in accordance with the requirements listed below

to allow for proper fireplace cooling. Failure to do this will create a severe fire risk.

The chase (fireplace enclosure) circulates room air. We recommend dry-walling the interior of the

enclosure or using suitable means to prevent dust or building debris from being circulated into the

room. Plastic sheeting may not be used in place of dry wall.

Chase Ventilation Overview

The chase may be ventilated from the sides (see “a” below) or from the front (see “b” and “c” below).









b

ca

a

Installation (for qualified installers only) 15

Chase Ventilation Grills

Use the included grill(s) to ventilate the chase (and fireplace). These grills provide a 50 square inch

opening (free air) to the chase. If alternative grills are desired, they must provide a minimum 50

square inches of free air to the fireplace (contact your dealer for details).

Dimensions

Height

(a)

Width

(b)

Depth

(c)

Min.

Framing

Height

Min.

Framing

Width

Front Ventilation Grill3-3/4"38"1-1/8"2-1/2"36"

Small Ventilation Grill4"16-1/4"4-5/8"2-3/4"14-3/8"

a

b

c

The grills must be attached directly to the chase cavity.

The included grills use ¼” screen to prevent debris, etc. from entering the chase.

Do not place any items inside the included ventilation grills. Grills should not be placed inside

shelving or near a location where it would become blocked by furniture or other items.

The chase air is drawn from the grills and exits a built-in channel on the upper manifold.

The ventilation air for the chase MUST be drawn from the same room containing the fireplace.

16 Installation (for qualified installers only)

Chase Ventilation – Front Configuration

If ventilation is provided from the front, you must remove both front inlet knockouts located under the

door opening. The ventilation air passes through the front of the fireplace and exits through the

convection air outlet. In addition, some of this air passes out of the side vents and ventilates the

chase.



When ventilating through the front, the grill is either placed directly on the fireplace or installed into a

raised non-combustible hearth. This hearth must be hollow and able to freely convey air to the

fireplace.









b

c







a

NOTE: If supports are provided in front of these knockouts, these supports must not limit the air

opening to less than 50 square inches.

For front configurations, you must use the large grill (38” x 3-3/4” outside dim.), or both small grills

(16-1/4” x 4” outside dim.), or equivalent free air opening (see note above).

Installation (for qualified installers only) 17

Chase Ventilation – Side Configuration

If ventilation is provided from the side, you must leave a 2” air gap to the both sides of the fireplace

(see illustration below). The ventilation air passes from the grills, through the chase, into the side

vents and exits through the convection air outlet.

MIn. 2"

Max.. 5-1/2"

This shaded area on both sides of the fireplace must be left

unobstructed when using the side chase ventilation configuration.

TOP OF FIREPLACE

When ventilating from the sides, you must use both small grills (16-1/4” x 4” outside dim.), or

equivalent free air opening (see note above). One grill must be placed on each side of the fireplace.

Vertically, the grills must be placed within 24” of the base of the fireplace (see illustration below).

If placed on a side wall, the grills must be placed directly to the side of the fireplace.

If placed on the front wall, the grills must be placed within 12” of the fireplace.



18 Installation (for qualified installers only)

Raised Fireplaces

The fireplace (and hearth, if desired) may be placed on a platform designed to support the fireplace

and vent (approximately 600 lbs.). See illustration below.

The ceiling in front of the fireplace must be a minimum 82” from the base of the fireplace.







42 Apex CF

Fireplace





Min. 3-1/2"



Min. 82"

Framing Header

Celing

Min. 6-1/2"

Convection

Air Outlet

Installation (for qualified installers only) 19

Approved Chimney

This fireplace requires one of two types of chimney (no exceptions – do not intermix):

Air-Cooled Chimney

- Use Travis Industries air cooled pipe only. Part

numbers are listed in the section “Air Cooled

Chimney”.

- This chimney requires the use of the air-cooled

starter section and cooling duct inlet (see the

section “Air Cooled Chimney” for details).

Insulated Chimney

- Security ASHT+ Chimney

(available from Travis Industries or Security)

(use 98900290 Anchor Plate)

- Alternative Manufacturers

(see the section starting on page 18 for details)

The entire chimney system must be installed to meet all local requirements as well as those

requirements listed by the chimney manufacturer. Depending on the manufacturer and where the

chimney is to be installed, chimney supports, roof braces, radiation shields, attic insulation shields,

attic enclosures, spark arrestors, locking bands, etcetera, may be required as part of the chimney

system. The manufacturer's installation instructions, which are reviewed by the listing agency,

specifies when and where each of these components must be used. Follow the manufacturer's

instructions for the use of flashing and an adjustable storm collar at the roof line to prevent water from

entering the house. Manufacturers require that chimneys extending beyond a certain height above

the roof (typically above 5') must be braced.

20 Installation (for qualified installers only)

Air Cooled Chimney Requirements (8” Inner Dia., 12” Outer Dia.)

Part Numbers (available through Travis Industries)

Chimney Components Part #

Anchor Plate – Air Cooled Chimney - REQUIRED 98900016

Cooling Duct Kit -6” Diameter - REQUIRED 98900108

48” Chimney Section 98900001

36" Chimney Section 98900002

24" Chimney Section 98900003

18" Chimney Section 98900004

12" Chimney Section 98900005

30° Offsets / Elbows (Qty 2) 98900006

Firestop (90°) 98900007

Firestop (30° - for angled sections) 98900008

Storm Collar 98900009

Round Termination Cap 98900010

Flashing 0-6/12 (for flat roofs up to 6/12 pitch - 26.5°) 98900011

Flashing 7-12/12 (for roofs 6/12 pitch to 12/12 – 26.5° to 45°) 98900012

Attic Insulation Shield 98900015

Anchor Plate Installation

The air-cooled chimney requires an anchor plate that includes a cooling duct inlet. Attach the anchor

plate to the top of the fireplace with the four included sheet-metal screws (see illustration below). The

cooling duct inlet can be directed to any direction (typically it is directed to the right rear).

Seal the fireplace connection with high-temperature silicone.

Seal the flue liner with furnace cement.

High-Temperature

Silicone

Use high-temperature silicone to

seal the anchor plate.

Furnace Cement

FireplaceXtrordinair 42 Apex Clean Face User manual

Popular Indoor Fireplace manuals by other brands