FireplaceXtrordinair 4237 User manual

4237 EG Fireplace
Page 1 of 3 17602223 - 10/6/2021 Travis Industries, Inc.
This fireplace is larger than most fireplaces and requires special attention when moving into position. The directions
below are intended as a guideline for this process.
Do not lift the fireplace from below with lifting forks. This may cause the base to bend and warp.
Always use proper lifting techniques when moving heavy objects (bend your knees, not your back).
We recommend using the Travis Industries lifting handles (sku# 98500711) for moving the fireplace.
See the instructions included with the brackets for installation instructions.
1. Remove the screen box in front of the firebox opening and place it aside.
2. Locate and remove the glass frame tool from the fireplace.
GLASS FRAME TOOL
The glass frame tool is shipped inside the fireplace, on the right side of the fireplace opening. The first time it is used you
may need to loosen the screw (1/4” nut driver). The tool is accessed after removing the screen.
NOTE: Replace the tool in this location after use.

4237 EG Fireplace
Page 2 of 3 17602223 - 10/6/2021 Travis Industries, Inc.
3. Remove the glass frame and place it aside.
4. The fireplace may now be moved into location. We recommend using the Travis Industries lifting handles
(sku# 98500711) for this process. The handles attach to the two brackets attached to the side of the
fireplace.
5. Unscrew the bolts on the side of the fireplace that secures the brackets to the pallet (1/2” wrench).
6. Move the fireplace into position, taking care not to damage the fireplace or surrounding area. If you do
wish to move the fireplace with a forked stove lift (e.g. Escalera), we recommend lifting from the firebox
roof (place 2x4’s into the firebox to distribute the load).
7. Once the fireplace is near its final position, remove the shipping brackets from the side of the fireplace
and slide it into place (3/8” wrench). Replace glass and screen box to prevent dust infiltration.
The Exhaust Restrictor and Horizontal Termination Shield are Lock-Tied to the Top of the Fireplace
See the installation manual for details on when and where these components are used.
8. This fireplace offers the choice of three, high-definition log sets (Oak, Birch, or Bon-Fyre).
YOU MUST CHOOSE A LOG SET TO COMPLETE THIS FIREPLACE.
Oak sku# 94500983 Birch sku# 94500982 Bon-Fyre sku# 94500984

4237 EG Fireplace
Page 3 of 3 17602223 - 10/6/2021 Travis Industries, Inc.
9. This fireplace offers the choice of five fireback sets (Standard Brick, Herringbone Brick, Black Enamel,
Stacked Tan Brick, and Black Glass) Comes with rear and side firebacks (only rear firebacks shown
below).
YOU MUST CHOOSE A FIREBACK SET TO COMPLETE THIS FIREPLACE.
Brick sku# 96100879 Herringbone sku# 96100880 Black Enamel sku# 96100875
Stacked Tan sku# 96100882 Black Glass# 96100881
10. Ember-Glo™ Lights - This heater comes with Ember-
Glo™ lights. After detailing the fireplace, adjust the built in
rheostat for the desired amount of ember glow. The
remote can then be used to turn the Ember-Glo™ lights
on and off (they will turn on and off with the fireplace).
11. This fireplace is compatible with the CoolSmart TV™
system. This kit allows for a TV pocket to be installed or
an installation of a TV above the fireplace without a
mantel.
12. An LP stepper motor is required if using propane with this
heater (4-pack = sku# 94400999 or single = sku# 250-
01463).