FireplaceXtrordinair 95801021 FPL ELECTRIC 51 User manual

FIREPLACEXTRORDINAIR
95801021 FPL ELECTRIC 51, 95801022 FPL ELECTRIC 64, 95801022 FPL ELECTRIC 115

TABLE OF CONTENTS
1
CONGRATULATIONS!
many years of dependable and enjoyable service from your Fireplacextrordinair product.
95801021 FPL ELECTRIC 51 4
95801022 FPL ELECTRIC 64
95801022 FPL ELECTRIC 115
7
12
15
16
20
24
25
27
9
10
13
14
21
22
23
Page 5
Page 6
Mood Light

IMPORTANT INSTRUCTIONS
SAVE THESE INSTRUCTIONS
WARNING!
3
B
A
C D
Fig. 1
Grounding Pin
Cover Of Grounded
Outlet Box
Metal
Screws
Adapter
Grounding
Means Grounding
Pin
electric shock, and injury to persons, including the following:
such as furniture, pillows, bedding, papers, clothes, etc. and curtains at least 3 feet ( 0.9 m) from the front of the
heater and keep them away from the sides and rear.
shock or fire, or damage the heater.
8.To prevent a possible fire, do not block air intakes or exhaust in any manner.
9.A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable vapors
or liquids are used or stored.
10.Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause
fire, electric shock, or injury to persons.
11. SAVE THESE INSTRUCTIONS.
needed. If in doubt, please visit our website at www.Fireplacextrordinair.com for the most recent version of the manual.
14.To reduce the risk of fire, do not store or use gasoline or other flammable vapors and liquids in the vicinity of the heater.
receptacles. The green grounding plug extending from the adapter must be connected to a permanent ground such as a
properly grounded outlet box. The adapter should not be used if a three-slot grounded receptacle is available.
immediately unplug the heater and inspect for an objects on or adjacent to the heater that may have locked the airflow or
otherwise caused high temperatures to have occurred. DO NOT OPERATE THE HEATER WITH THE ALARM ILLUMINATION.
4. Do not operate any heater aer it malfuncons. Disconnect power at service panel and have heater inspected.
5. Do not use outdoors. (Omied if the heater is intended for outdoor use.)
6. To disconnect heater, turn controls to off, and turn off power to heater circuit at main disconnect panel (or
operate internal disconnect switch if provided).
discoloraon or damage to

95801021 FPL ELECTRIC 51
4
WM-BI-43-5123
Built-In Appliance
120V AC,60Hz
1400W
11.7A
Model Number
Voltage
Amps
43” or 109.30 cm
17” or 43.00 cm
5 1/2” or 14.00 cm
7 3/16” or 18.30 cm
70.00 lbs or 31.75kg
71.43 lbs or 32.4 kg
Right side
Appliance Width (Glass & Stone)
Appliance Height (Glass & Stone)
Appliance Depth Glass Models
Appliance Depth Stone Models
Gross Weight Glass Models
Gross Weight Stone Models
Cord Length 74.81” or 190.00 cm
HEATER HIGH
LOW
NO HEATER
1350W
675W
23W
MOTOR HEATER
MOTOR FLAME
14.5W
4W
21
93
16
39
51
2
17
21
16
51
73
16
5
16
17
16
7
8
7
8
43
4006492
Rough Wall Opening Size
NOTE: This appliance must be electrically
wired and grounded in accordance with
local codes. In the absence of local codes,
us the current CSA C22.1 Canadian Electrical
Code in Canada or the ANSI/NFPA 70
States
This appliance has been tested in
accordance with the UL Standard 2021 for
appliances in the United States and Canada.
If you need assistance during installaon,
please contact your local dealer

5
Built-In Appliance
120V AC,60Hz
1400W
11.7A
Model Number
Voltage
Amps
58” or 147.30 cm
17” or 43.00 cm
5 1/2” or 14.00 cm
7 3/16” or 18.30 cm
84.99 lbs or 38.55kg
86.93 lbs or 39.43 kg
Right side
Appliance Width (Glass & Stone)
Appliance Height (Glass & Stone)
Appliance Depth Glass Models
Appliance Depth Stone Models
Gross Weight Glass Models
Gross Weight Stone Models
Cord Length 74.81” or 190.00 cm
HEATER HIGH
LOW
NO HEATER
1350W
675W
27W
MOTOR HEATER
MOTOR FLAME
14.5W
6W
95801022 FPL ELECTRIC 64
95801022 FPL ELECTRIC 64
21
93
16
54 7
16
64
51
2
17
21
16
73
16
5
16
17
16
7
8
7
8
58
4006492
Rough Wall Opening Size
NOTE: This appliance must be electrically
wired and grounded in accordance with
local codes. In the absence of local codes,
us the current CSA C22.1 Canadian Electrical
Code in Canada or the ANSI/NFPA 70
States
This appliance has been tested in
accordance with the UL Standard 2021 for
appliances in the United States and Canada.
If you need assistance during installaon,
please contact your local dealer

4
95801022 FPL ELECTRIC 115
6
95801022 FPL ELECTRIC 115
Built-In Appliance
120V AC,60Hz
1400W
11.7A
Model Number
Voltage
Amps
106” or 269.30 cm
17” or 43.00 cm
5 1/2” or 14.00 cm
7 3/16” or 18.30 cm
153.64 lbs or 69.69kg
157.19 lbs or 71.30 kg
Right side
Appliance Width (Glass & Stone)
Appliance Height (Glass & Stone)
Appliance Depth Glass Models
Appliance Depth Stone Models
Gross Weight Glass Models
Gross Weight Stone Models
Cord Length 74.81” or 190.00 cm
HEATER HIGH
LOW
NO HEATER
1350W
675W
35W
MOTOR HEATER
MOTOR FLAME
14.5W
6W
NOTE: This appliance must be electrically
wired and grounded in accordance with
local codes. In the absence of local codes,
us the current CSA C22.1 Canadian Electrical
Code in Canada or the ANSI/NFPA 70
States
51
2
17
29
16
73
16
5
16
17
16
7
8
21
93
16
103 1
115
7
8
106
4006492
This appliance has been tested in
accordance with the UL Standard 2021 for
appliances in the United States and Canada.
Rough Wall Opening Size
If you need assistance during installaon,
please contact your local dealer

INSTALLATION OVERVIEW
NOTE: BEFORE YOU INSTALL
SITE SELECTION
wall.
Review and consider all of the following condi-
r r wo (2) wall
ethods:
t-In (page 11)
W nt (Page 13)
re the power cord is stalled so
tha s pinched or against a sharp edge
and re tha e power cord is stored
or red to avoid tripping or snagging
ry to persons.
st c with local codes
-
ry to persons.
rapes, pillow
dir ht and away fr overhead
lighng.
electric et for ease of electric
and all hardware fr ox and r ove all
packaging relat aterials prior to
WARNING:
T
Phillip rewdriver
aw and/ aw
Level
Tape
Pliers
re
Gloves
7
E
Fr aterials
Wall Finishing
Marterials
aterials
stable)
TOOLS & BUILDING SUPPLIES
NORMALLY REQUIRED
Volt cir r red.
cated cir referr -
Power supply Wire Gage
Voltage Wire Gage Fuse
120 v 14 G . 15 MP
Wall switch / t hermostat Wire Gage
Voltage Wire Gage
5 Volts 18 Gage
PACKAGING LIST
with:
r te control
To reduce the risk of fire, do not store or
use gasoline or other flammable vapors
and liquids in the vicinity of the heater.
furniture etc.
installaon (Figures 1, 2, 3, 4)

INSTALLATION OVERVIEW
8
(Figure 3)
Remove sides of box
Remove packaging surrounding the unit and front.
(Figure 4)
Discard packaging materials and store
(Figure 2)
(Figure 1)
43”/ 58” 106”
43”/ 58” 106”

PACKAGE CONTENTS
A
E
BC
D
CONTENTS
Part Description Quantity Picture
Screw
0.16 in. x 1.0 in.
Wall Plug
0.3 in. x 1.5 in.
20
20
B
A
0.16 in. x 0.6 in. 12
C
Screw
0.16 in. x 0.3 in. 2
D
9
Wood Screw
Part
1
Glass
A
B 1
C Wall Bracket 1
D1
E Fire Glass Media 1 (43")
2 (58")
3 (106")

NEW CONSTRUCTION OR
RENOVATION
CAUTION:
Two people may be needed to
moisture and is located at least 0.91 m or
-
als such as curtains or drapes, furniture,
bedding, paper, etc.
Minimum Clearance of the fireplace to
the adjacent wall
2. Place the appliance in selected loca-
and store appliance in a safe, dry and
4. Prepare a wall with a framed open-
ing to accommodate the size of your unit.
Leave at least 1/4” (6mm) around the
edge of the appliance. Any new wiring
must be done in compliance with local
and na l codes and other applicable
outlets or circuits. To reduce the risk
licensed electrician.
WARNING:
To prevent contact with sagging or
-
ance must not be installed against
result.
WARNING:
10
Sides ---------------------- 6in / 15 cm
Floor ---------------------- 6 in / 15 cm
Top ---------------------- 6 in / 15 cm
Back ---------------------- 0 in / 0 cm
Figure 5
min. 15 cm
6 in
min. 15 cm
6 in
min. 15 cm
6 in
WALL
FLOOR
a
b
c
Dry Wall
95801021 FPL ELECTRIC 51
95801022 FPL ELECTRIC 64
95801022 FPL ELECTRIC 115
a b c
43"
58"
106"
44"
59"
107"
17"
17"
17"
5 "
2
1
5 "
2
1
5 "
2
1
Model number

F ron
-
FIREPLACE INSTALLATION BUILT IN
just the unit to achieve the desired amount
of depth. (Figure 6)
k r ow
w
-
and the wall studs. (Figure 7)
Figure 7
Figure 6
NOTE BEFORE YOU INSTALL
Wall
11
Power cord
Power cord

Floor
It is strongly recommended that the screws be
screwed into the wall studs where possible. If
anchors are used.
(Figure 8)
ke sure it is level.
hanging into the keyholes on the back of the unit.
(Figure 9, Figure 10)
3. Check the appliance for stability ensuring that
the appliance will not pull free from the wall.
Figure 8
Figure 9
NOTE: BEFORE YOU INSTALL
Stakes for hanging
wall bracket
Back of unit
12
Figure 10
Stakes for hanging
Side view
Wall
3 feet

Release the screws
Step 1
Remove the cover
Feed the supply wires thought
the 7/8” @22.2 wire hole and
Lock the power cord stator
Connect the Live wire (Black)
Connect the Ground wire (Yellow)
Connect the Neutral wire (White)
Screw the strain relief
Step 2
cover back
Screw the cover
Touch Panel
Step 3
13
- HARD-WIRE
Ensure the unit is power off and
the plug is note plugged before
WARNING:
Touch Panel

1. To change from log to Fire Glass Media (Figure 12.1)
log set out.
2. Choose the colour of Fire Glass Media you would like to use. (Figure 11)
3. Place the Fire Glass Media into the Tray (Figure 12.2)
It is not necessary to use all the media supplied.
Figure 12.1
Figure 12.2
Hz-10 Harvest moon
Hz-09 Sun Tea
HZ-01 Clear
CLEANING THE MEDIA: The media may contain a fine white dust that needs
thoroughly and dry before placing into the tray.
14

NOTE: BEFORE YOU INSTALL
FRONT INSTALLATION
It is recommended that two people install the
front onto the appliance, wear safety glasses and
gloves when handling glass.
brackets with the four (4) shoulder screws on the
side of the appliance body (Figure 14, or Figure
15)
Figure 13
Figure 14 Figure 16Figure 15
Wall
Unit
Shoulder Screw
Wall
Mount
Unit
Shoulder Screw Screw
15

OPERATING THE UNIT
GETTING POWER TO THE UNIT
1. Make sure the appliance is switched OFF (refer
on the right hand side of the unit. (Figure 16)
3. Plug unit into electrical outlet.
Wall
outlets or circuits. To reduce the risk of
licensed electrician.
WARNING:
Figure 17
Power adaptor port
16
Inspect for an objects on or adjacent to
the heater that may have locked the
airflow or otherwise caused high
temperatures to have occurred.
This heater is include a visual alarm (“F”
– shown & flash on the display) warn
-
sively hot. If the alarm illuminates,
immediately unplug the heater from
minutes plug the unit back into wall
outlet, operate as normal.
4

OPERATING THE UNIT
CONTROLLING THE FIREPLACE
Figure 18
Figure 19
°F
°C
IR ON/OFF FLAME/
EMBERS
DISPLAY HEAT TIMERS
a.IR: Receiving infra-red signals(inputs)
b.ON/OFF: (Power indicator) The
indicator
will be on when the appliance is
standby mode.
c.FLAME/EMBERS: (Flame light andembers light indicator) The indicator will be on
on.
on.
g. /℉The corresponding indicator will be on when the
corresponding temperature unit is used during temperature adjustment.
DISPLAY AND FUNCTIONS
CONTROLLING METHOD:
17
Remote control:
POWER:
TIME SETTING:
will be invalid.)
unit) the ON/OFFindicator on the main body display will
be on when the appliance is turned on.
This infra-red (IR) remote control,
d.DISPLAY: (Mul-funconal digital display) The panel displays flame light intensity 1 to
level 5 and embers light intensity from level 0 to level 5. When the temperature is adjusng,
the panel will display the corresponding temperature in F/ C. It can also display me while the
mer is seng up, and the heang stage number. When the seng of funcon is changing,
the display will show the corresponding funcon display. Aer 5 seconds without any input
signals, the digital dsiplay will be closed. When we set the heang stage at level 1 or level 2
manually, the digital display will be 1 or 2
O O

18
REDUCING EMBERS LIGHT INTENSITY:
INCREASING EMBERS LIGHT INTENSITY:
HEATER SWITCH:
HIGH HEATING LEVEL:
℃
LOW HEATING LEVEL:
℃
TEMPERATURE ADJUSTING:
℉ ℉ ℃ ℃ ℉ ℃
℉ ℃
REDUCING FLAME INTENSITY:
INCREASING FLAME INTENSITY:
ON: The heateris ready to start display panel indicates “ON” and the visual on indicator will
OFF: Display panel indicates “--”.
Remark: If you would like to set the thermostatsimply use TEMP key on remote and HEAT key
on the display panel of fireplace will display it goes from 68 -86℉.
see the desired temperature.