Firesense 63246 User manual

SAVE THESE INSTRUCTIONS
FOR FUTURE REFERENCE.
ATTACH YOUR
RECEIPT HERE
Keep a copy of your proof of
purchase or order confirmation
which will be needed if you need
to contact us about warranty
coverage.
Purchase Date:
Round Tempered Glass Wind Guard for Gas Fire Pits
Item #: 63246, 64009
05242022
Email
Live chat
www.balkenehome.com
Questions, problems, missing parts?
Before returning to your retailer, our Florida-based customer service team is available to assist.
English & Spanish speaking.
Call toll-free (866) 985-7877 9 a.m. – 9 p.m., EST
9 a.m. – 6 p.m., EST., Monday - Friday

2
BEFORE YOU BEGIN
Before beginning assembly, make sure all parts are present. Compare parts received with the "Package
Contents." If any part is missing or damages, do NOT attempt to assemble the product. Please read and
understand this entire manual before attempting to assemble, operate, or install this product. If you have
SAFETY INFORMATION
WARNING
DO NOT stand or allow children to stand on the assembled product. DO NOT place anything on top of the
assembled product. DO NOT tighten screws completely until instructed to do so. After final alignment, make
sure all hardware is securely fastened before attempting to move the unit. NEVER use a power tool to
assemble or adjust your item. Perform periodic checks to make sure the hardware is secure and tighten if
needed.
CAUTION
Read all instructions before beginning assembly. Failure to do so may result in faulty assembly and potential
injury. Assemble the item on a soft, non-abrasive surface such as a towel or blanket to avoid damaging the
item.
CARE
When wind guard is completely cool, it may be cleaned with a soft cloth or paper towel and standard glass
cleaner. Never spray cleaner or water on a hot wind guard, as it could crack or shatter.
Store the wind guard in a safe place during poor weather or when not in regular use.
Contact us for assistance: (866) 985-7877 | www.balkenehome.com
INFORMATION

3
PART DESCRIPTION QUANTITY
Glass Panel 4
HARDWARE CONTENTS
Contact us for assistance: (866) 985-7877 | www.balkenehome.com
C
Bottom Bracket
Qty: 4
Screwdriver
Qty: 1
PACKAGE CONTENTS
B
Top Bracket
Qty: 4
NOTE: Each of the eight wind guard brackets should arrive with two flat-ended screws pre-assembled in
the bracket. Each screw should have a clear rubbery pad/cap at the inner tip that protects the glass panel
from the screw and helps hold the panels in place. Sometimes small parts can rattle loose in shipping, so
check each bracket and screw for proper assembly before assembling the wind guard. If any screw or
screw pad is missing, check the packaging for the hardware and the shipping carton.
Contact Customer Service at [email protected] for replacement parts if necessary.
To replace a screw pad:
Press the clear pad into the tip of the screw
To replace a screw:
Screw the screw partially into the bracket (do not fully tighten)
Flat-end
Screw (Spare)
Qty: 2
Screw-tip
Pad (Spare)
Qty: 2

4
1
2
PREPARATION
Hardware Used: B Top Bracket x4
Contact us for assistance: (866) 985-7877 | www.balkenehome.com
Before beginning assembly, be sure to empty contents of carton and make sure all parts are present. If
any parts are missing, please contact Customer Service at (866) 985-7877, 9 a.m.–9 p.m., EST., or
email [email protected].
Carefully remove the glass panels from the packaging and inspect for any damage such as chips
or cracks. Place glass panels on a soft, flat surface to prevent any damage. Before assembly, ensure
that each bracket has 2 set-screws, with silicone pads attached at the tip.
Estimated Assembly Time: 30 minutes | Do NOT over-tighten hardware!
ASSEMBLY
You will assemble the wind guard upside-down. It is
recommended to assemble on the floor on a protected
surface such as a blanket to avoid accidental breakage.
Arrange the four glass Panels A in a circle.
Verify that all Brackets B/C are assembled with a plastic
bumper pad at the tip of both set-screws and with the set-
screws loosened adequately to allow the brackets to slide
easily onto the glass panels.
Slide a Top Bracket B onto the junction of two Glass
Panels A as shown.
Align the Bracket with the lower (top) edges of the adjoining
Panels.
Verify that the bumper pad is in place at the tip of each
bracket set-screw. Do NOT tighten the screw directly to
the glass if the pad is missing. Check the carton for spare
pads, or contact Customer Service.
Check alignment, then carefully tighten set-screws until snug.
WARNING: over-tightening can break glass!
Continue to join Panels one at a time by the same procedure
until all four panels are joined to form a complete circle. Once
all four Top Brackets are in place, check the security of all
eight set-screws.

Contact us for assistance: (866) 985-7877 | www.balkenehome.com 5
3
4
Hardware Used: C Bottom Bracket x4
Carefully (using two people if possible) turn the assembled
wind guard upright. Gently set the glass guard onto the fire
pit table, positioning the feet flat and level outside the
edges of the burner. Check that the bottom edges of the
glass panels are not directly touching the tabletop, and are
held off slightly by the foot pads of the lower brackets.
Ensure that the foot pads are not sitting directly on the fire
bowl.
Be aware that the glass and hardware may become warm
or hot after prolonged burning of the fire pit and take
reasonable precautions to avoid burns.
Carefully slide a Bottom Bracket C onto the top of each
panel joint, with the cushioned foot pad pointed UP.
Align the edge of the metal Bracket with the edge of the two
glass panels, adjusted so the foot pad will hold the
assembled wind guard slightly off the table surface when
placed upright.
Verify that the bumper pad is in place at the tip of each
bracket set-screw. Do NOT tighten the screw directly to
the glass if the pad is missing. Check the carton for spare
pads, or contact Customer Service.
Check alignment, then carefully tighten set-screws until snug.
WARNING: over-tightening can break glass!
Install the remaining three Bottom Brackets in the same
manner.
ASSEMBLY

T /
,
,½ "½8*,--½7,, /-½8*/½-
-
/
¤
T ½*1,-
,
½--1-
½,--½ ½/½
--
9½ ½
"
*,/
"
½
"
½/
-
½1 /
¤
T ½1
,
½/
"
½
"
"
77
,
-
½
"*,/" -/,1/" -½" / ½
/
-
½ 1
½
,
-
1
/
½
-
6
,
½
*,"*
,
/9½
½ ¼"
,
½*,-" 1
,
9¤
T ½ ½ "½6 / 7
7
½/,6½6 \½"
,
½
/-½,/",-\½",-½",½ /-½
½
½
/"½/½*1,-,½",½
9½/
,
½
*
,
/9
\
½
7
/
,
½ ½" /,/\½ ½/",/\½",½
"
½ 9½
"
/
,
½
-
-
\½
",
½
9
½
,
/\½
-*
\
½
*
1 /6\½8
*
,9\½" -+1 /
\
½"
,
½
/
"--\½ "-/\½",½½,- ½
"1/ "½",½ ½" /" ½
7/
½/½-
\½
/ \½1-\½",½
/
9½
/
"½1-½/½
*,"1/\½6 ½½7
½/
,
6
½
6 ½"
,
½
/-½,/",-\½",-½",½ /-½6½
½
6-½"½/½*"--
/9
½ " -1
"---\½
"-/-½",½-\½",½ -1½"---\½"-/-\½
",
½
-
½
,
½
",
-
¤½ ½
"
½6 /½
7
½7½/
,
6
½6 \½",½/-½",-\
,/",-\½",½ /-½
½
½",½
9
½
,/½
"---
\
"-/-½",½-½//½
8½/½*1,-½*,½"½/½*,"1/¤
T ½-"½1,-/" -½"½ "/ "7½
/
½
8
1
-" ½",½ //" ½
"
½ /
"
,½
"
-
+
1 /
-
\½
-"
½/½
"
6½
//" ½",½ 8
1
-" ½
9
½ "/
**
9
½ /"½
/½*1,-,¤
³¿>¿½ ¿Ug
Before returning½¿ >Ug t½Å³U>¶g#tµ¿UɸÁgµ ¸gµÐUg >_ Ñ>µµ>ÁÓ¿¸¸Ég¸[
>
¿Á
t
µgg
>
Ðg¿U
>Á¿
¿>¦¦¿o¿¿
¡
¦¦\¿-
/
¢l»»£½luºlºº
U¶g³ÌUgJÍg¿³>Ìgg_¤g¿
L>ggg¤U 9 a.m. – 6 p.m., EST, Mon – Fri
¶¿³LÅ¿g_½LÏ
[
7g
¿/µ>Ðg
g
_
¿Ðy
@4ABB"C
)
BC<!!CB/!
.
+B>
.
0
BBDELD
'
L>
g
g
g
¦
U
>!<G+!H!
..
C<G!
.
!
80!C
6
"AA
7
B1"&*@"@@
+<
!
B
!
0
>!
=
B
*>
Á
¿ -g¸g
\
¶
¿Ð>¿g
\
¶
¿
3,
G!BF0
=
B
F
.
0
=
¿¿>gg¿g
=
¶
0
B
!
..B
<G!.! B+G+0
(
=
B<!B<!
(
+>C!<! BC< !/<->B3
%
B
!
..B<G!.! B/
5
3<C>B0
=
8
..B>>!/.JB+0>C<FC+30B
5
<!>!0CC+30>B<!BC)!B
5
<3
5
!<CJB
3
%B
!
..B
<G!.! B/53<C>B08
=
B0 B<!B
5
<3C!C! BJ
88B3
5
J<+()C>B0 BC<
!
/
<-
>
8B
..B<+()C>B<!>!<G! 8
8/ ½9"1,½7,, /9
7g¿ÓÉ¿¡ÉµU>¸g¿>¿µg¿-g¸g¿µ¿>gg¿g¿¡µ_ÉUÁ¿tµ¿>Ó¿>ÉÁµ×g_¿µgÁ>gµ\¿ÓÉ´¿>Ðg¿¡g>Ug¿
t¿_¿¿Ñy¿Á>Á¿Á¿Ug¸¿ÑÁ¿>¿gÓg>µ¿Ñ>µµ>ÁÓ¦¿ÒÁg_¿Óɵ¿Ñ>µµ>ÁÓ¿tµ¿an additional year¿
Ñg¿ÓÉ¿µgÐgÑ¿Óɵ¿Ág¿>Á¿L>ggg¤U½ÑÁ¿Ã½u¿_>Ó¸¿t¿¡ÉµU>¸g¦
LÓ
/½7,, /9
Ŷ¿g³¶½½¿g½¿yÅŶ½1-
7¿½³t½t½Å³U>¶g½t³½>½>Å¿³Óg_½³g¿>g³\¿Á¸¿¡µ_ÉUÁ¿¸¿Ñ>µµ>Ág_¿
tµ¿>¿¡gµ_¿t¿¿Óg>µ¿tµ¿µy>¿¡ÉµU>¸g¿_>Ág¿>y>¸Á¿_gtgUÁ¸¿¿>Ágµ>¸¿
>_¿Ñµ>¸¡¿É_gµ¿µ>¿É¸g¦¿/¸¿Ñ>µµ>ÁÓ¿_g¸¿ "/¿UÐgµ¿µ>¿
Ñg>µ¾Ñg>Ágµy\¿gÒ¡¸Éµg¿Á¿Ñ>Ágµ\¿tµgg×y¿Ág¡gµ>Áɵg¸\¿¸\¿tÉ_¸\¿µ¿
UgU>¸¿",¿É¸g¿¿>¿UgµU>¿UÁgÒÁ¿t¿Ág¿ÉÁ¿¸¿Á¿_g¸y>Ág_¿>¸¿>¿
UgµU>¿_g¦¿Á¿7g¿/µ>Ðgg_¿Ðy²¸¿¸g¿_¸UµgÁ\¿¡µ_ÉUÁ¸¿É_gµ¿
Ñ>µµ>ÁÓ¿Ñ¿Lg¿µg¡>µg_¿>_¾µ¿µg¡>Ug_¿>Á¿¿U>µyg¿Á¿Ág¿UɸÁgµ¦¿
,gÁɵ¸¿¸gÁ¿L>U¿Á¿7g¿/µ>Ðgg_¿Ðy¿É¸Á¿Lg¿¸gÁ¿Ð>¿¡µg¡>_¿tµgyÁ¿¿
Ág¿µy>¿µgÁ>¿¡>U>yy¦
µ¿Ñ>µµ>ÁÓ¿¸gµÐUg\¿UÁ>UÁ¿>gg¿g¾7g¿/µ>Ðgg_¿Ðy¿>Á¿Ág¿
>__µg¸¸\¿¡g¿ÉLgµ¸¿µ¿ÑgL¸Ág¿>_¿g>¿¸Ág_¿¿Á¸¿Ñgµ²¸¿>É>¦¿
g¿¸Éµg¿Á¿>Ðg¿Óɵ¿¸>g¸¿µgUg¡Á\¿_>Ág¿t¿¡ÉµU>¸g¿>_¿U>Á>yÉg¾_g¿
ÉLgµ¸¿>Ð>>Lg¿Ñg¿U>y¦¿¿Ñ>µµ>ÁÓ¿¸gµÐUg¿Ñ¿Lg¿Uµ_>Ág_¿LÓ¿
7g¿/µ>Ðgg_¿Ðy´¸¿g>¿¸>_\¿µ_>¿¸gµÐUg¿UgÁgµ¦¿/¸¿Ñ>µµ>ÁÓ¿¸¿
gÒÁg_g_¿Ó¿Á¿Ág¿µy>¿Ñgµ¦¿*µt¿t¿¡ÉµU>¸g¿Ñ¿Lg¿µgªÉµg_¿Lgtµg¿
Ñ>µµ>ÁÓ¿¸gµÐUg¿¸¿µg_gµg_¦¿/g¿¸>g¸¿µgUg¡Á¿¸¿Ág¿Ó¿Ð>_¿¡µt¿t¿
¡ÉµU>¸g¦¿/¸¿Ñ>µµ>ÁÓ¿Ó¿UÐgµ¸¿t>ɵg¸¿_Ég¿Á¿_gtgUÁ¸¿¿>Ágµ>¸¿µ¿
ѵ>¸¡¿ÑU¿UUɵ¿_ɵy¿µ>¿É¸g¦¿>ɵg¸¿>_¾µ¿_>>yg¿ÑU¿
µg¸ÉÁ¿tµ¿>UU_gÁ\¿gyygUg\¿¸É¸g\¿>Lɸg\¿gygUÁ\¿¸>_y\¿
>Ágµ>Á¿µ¿_tU>Á\¿t>ɵg¿Á¿>Á>\¿¡µ¡gµ¿>¸¸gLÓ¿µ¿
>Ág>Ug\¿¸gµÐUg¿LÓ¿É>ÉÁµ×g_¿>ygUÓ¿µ¿É¸g¿t¿É>ÉÁµ×g_¿
U¡gÁ¸¿µ¿_>>yg¿Á>Á¿¸¿>ÁÁµLÉÁ>Lg¿Á¿>UÁ¸¿t¿_¿>µg¿ "/¿UÐgµg_¦
/¸¿Ág_¿Ñ>µµ>ÁÓ¿yÐg¸¿ÓÉ¿¸¡gUtU¿gy>¿µyÁ¸¿>_¿ÓÉ¿>Ó¿>¸¿>Ðg¿
Ágµ¿µyÁ¸¿ÑU¿Ð>µÓ¿tµ¿Éµ¸_UÁ¿Á¿Éµ¸_UÁ¦¿/g¿¡µÐ¸¸¿t¿Ág¿
1Ág_¿ >Á¸¿ÐgÁ¿¿Áµ>UÁ¸¿tµ¿Ág¿->g¸¿t¿_¸¿¸>¿Á¿>¡¡Ó¿
Á¿Á¸¿Ág_¿Ñ>µµ>ÁÓ¿µ¿Ág¿¸>g¿t¿¡µ_ÉUÁ¸¿UÐgµg_¿LÓ¿Á¸¿Ág_¿
Ñ>µµ>ÁÓ¦
This manual suits for next models
1
Table of contents
Other Firesense Safety Equipment manuals
Popular Safety Equipment manuals by other brands

GST
GST DI-9319E Quick start quide

3M
3M DBI-SALA Nano-Lok instruction manual

Petzl
Petzl AVAO BOD manual

TEUFELBERGER
TEUFELBERGER Slaice Manufacturer's information and instructions for use

Studer
Studer MBW 40 owner's manual

Federal Signal Corporation
Federal Signal Corporation SST3-MV Installation and maintenance instructions