Fisher & Paykel EB60DSX1 User manual

COFFEE MAKER
EB60DSX1, EB60MSG1 & EB60MSB1 models
INSTALLATION GUIDE
NZ AU GB IE SG

3
CONTENTS
Safety and warnings 4
Parts supplied 5
Prior to installation 5
After installation 5
Product dimensions 6
Cabinetry dimensions (460mm high cavity) 7
Cabinetry dimensions (480mm cavity trim kit) 8
Installation instructions 9
Connect the coffee maker to the mains supply 10
Final checklist 11

4
IMPORTANT SAFETY INSTRUCTIONS!
Installation
Checking for transport damage
After removing the packaging, make sure the product is complete and undamaged and that all
accessories are present. Do not use the appliance if it is visibly damaged. Contact Customer Care.
IMPORTANT!
● Installation must be performed by a qualified professional in compliance with legislation in
force in the country of installation.
● The packing elements (plastic bags, polystyrene foam, etc.) should be kept out of reach
of children.
● Never install the appliance in rooms where the temperature may drop to 0°C or lower.
● Customise the water hardness as soon as possible following the instructions in your
user guide.
● This appliance can be installed over a built-in oven if the latter is fitted with a cooling fan at
the rear (maximum microwave power: 3 kW).
● Connecting the appliance
● Danger! Check that the mains power supply voltage corresponds to the value indicated on
the rating plate on the bottom of the appliance.
● Connect the appliance to an efficiently earthed and correctly installed socket with a
minimum current rating of 10A only.
● Do not allow children and animals to stop or linger near the appliance when it is pulled out
of the cabinet.
● If the power socket does not match the plug on the appliance, have the socket replaced
with a suitable type by a qualified professional. To comply with safety directives, an
omnipolar switch with a minimum contact distance of 3 mm must be installed.
● Do not use multiple sockets or extensions.
● If the power socket does not match the plug on the appliance, have the socket replaced
with a suitable type by a qualified professional. To comply with safety directives, an
omnipolar switch with a minimum contact distance of 3 mm must be installed.
● Do not use multiple sockets or extensions.
● Safety cutout devices must be included in the mains power supply in compliance with the
installation regulations in the country concerned.
● This appliance conforms to EC Regulation 1935/2004 on materials and articles intended to
come into contact with food.
● Do not allow children and animals to stop or linger near the appliance when it is pulled out
of the cabinet-.
● Do not leave the machine pulled out of the cabinet when it is being used.
● Do not leave the machine pulled out of the cabinet when it is not needed.
● Install the machine according to the instructions in the handbook to guarantee there are no
spills when it is pulled out from the cabinet.
● The rails fixing panel must have a thickness suited to the fixing screws supplied standard.
● The panel material must be suited to the machine weight of approximately 25kg.
DISPOSAL
● The appliance must not be disposed of with household waste, but taken to an authorised
waste separation and recycling centre.
WARNING!
Cut Hazard
Take care – some edges are sharp.
Failure to use caution could result in injury or cuts.
SAFETY AND WARNINGS

5
Screws
(28)
Spacers
(4) for side
(4) for bottom
● The countertop and coffee maker cavity are square and level, and are the required dimensions.
● The installation will comply with all clearance requirements and applicable standards and regulations.
● The isolating switch will be easily accessible to the customer with the coffee maker installed.
● The electrician provides sufficient free length of power supply cable to reach from the bottom rear of the cavity
to at least 1.5m in front of the bottom edge of the opening.
● The cable may enter the cavity from the side, top or bottom, but top entry must be at the rear of the cavity.
● The coffee maker connection socket (if fitted) is outside the cavity if the oven is flush to the rear wall.
● The coffee maker will rest on a surface that can support its weight.
● The height from the floor suits the customer.
● You consult local building authorities and by-laws if in doubt regarding installation.
Some environmental factors and cooking habits can cause condensation in and around the coffee maker during use.
To protect surrounding cabinetry from possible damage caused by frequent or excessive condensation, we recommend
moisture-proofing the cavity.
IMPORTANT!
Take extra care not to damage the lower trim of the coffee maker during installation. The trim is important for correct air circulation and allows the door to open and close without obstruction.
The manufacturer does not accept any responsibility for damage resulting from incorrect installation.
● The coffee maker can be used fully without obstruction.
● The power supply cable does not touch any hot metal parts.
● The isolating switch is easily accessible to the customer with the coffee maker installed.
● You complete the ‘Final checklist’ at the end of the installation.
● If, after following the instructions given, correct performance cannot be achieved, please contact your nearest Fisher & Paykel Authorised Service Center, Customer Care, or
contact us through our local website listed at the end of this document.
Rails (2) Clip (1)
Optional Trim kit installation
If you are using a 762mm trim
kit, refer to the separate Trim Kit
Installation Guide.
PARTS SUPPLIED
PRIOR TO INSTALLATION
AFTER INSTALLATION

6
FRONT
TOP SIDE
PRODUCT DIMENSIONS
EB60 MODELS
mm
AOverall height of product 458
BOverall width of product 596
COverall depth of product 480
DHeight of chassis 445
EWidth of chassis 560
FDepth of chassis 460
GDepth of coffee maker frame and control panel 20
HStepdown control panel to chassis 13
IHeight of control panel 100
B
E
A
C F D
I
H
PRODUCT DIMENSIONS

7
Verify the minimum measurements required for correct installation of the appliance. The coffee maker must be
installed in a column and the column must be firmly fixed to the wall with commercially available brackets.
IMPORTANT!
● All installation or maintenance operations must be performed with the appliance disconnected
from the mains electricity supply.
● Kitchen furniture in direct contact with the appliance must be heat resistant 65°C min.
● To guarantee correct ventilation, leave a gap at the bottom of the cabinet
(see measurements below).
PROUD INSTALL
FLUSH INSTALL
16–20mm
2mm
16–20mm
Electrical supply
CABINETRY DIMENSIONS
EB60 MODELS
mm
IMinimum inside width of cavity 560
JOverall width of cabinetry 600
KMinimum inside height of cavity 450
LOverall height of cabinetry 460
MMinimum inside depth of cavity 545
nVentilation Air Gap 50
TOPSIDE
M
J
I
Lk
n
20mm
20mm
CABINETRY DIMENSIONS (460mm HIGH CAVITY)

8
Verify the minimum measurements required for correct installation of the appliance. The coffee maker must be
installed in a column and the column must be firmly fixed to the wall with commercially available brackets.
IMPORTANT!
● All installation or maintenance operations must be performed with the appliance disconnected
from the mains electricity supply.
● To guarantee correct ventilation, leave a gap at the bottom of the cabinet
(see measurements below).
TOPSIDE
Electrical supply
o
Lower
Trim kit
M
J
I
Lk
n
CABINETRY DIMENSIONS
EB60 MODELS
mm
IMinimum inside width of cavity 560
JOverall width of cabinetry 600
KMinimum inside height of cavity 470
LOverall height of cabinetry 480
MMinimum inside depth of cavity 545
nVentilation air vent 50
oHeight of trim kit 20
PROUD INSTALL
FLUSH INSTALL
16–20mm
2mm
16–20mm
20mm
20mm
CABINETRY DIMENSIONS (480mm CAVITY TRIM KIT)

9
1Align the rails to the sides of the cabinet before securing using the provided screws.
Extending both rails fully.
● If the coffee maker is installed over a warmer drawer, use the top surface of this as
a reference to position the rails.
● In this case, there will be no surface to rest the rails on.
2Fix the power cable with the clip. The power cable must be long enough to allow
the appliance to be pulled out from the cabinet to fill the coffee bean container.
● The appliance must be earthed in compliance with legislation.
● Electrical connections must be performed by a qualified electrician following
the instructions.
3Position the appliance on the rails, making sure the pins are correctly inserted
in the housings, then fix it with the screws supplied. If the height of the appliance
requires adjusting, use the spacer disks provided.
4If required, the alignment of the coffee maker can be adjusted by placing the
supplied spacers either under or to the sides of the rails.
5To adjust the height of the coffee maker front by ±2mm, rotate the lever
located where the coffee maker and rails meet.
approx. 350mm
560mm min
0.07”
(1.8mm)
INSTALLATION INSTRUCTIONS

10
IMPORTANT!
● All electrical work may only be carried out by suitably qualified and competent persons in accordance with national and
local safety regulations.
● This warming drawer must be earthed.
Before placing the coffee maker into the cavity, route the power cord into the back of the cavity and plug it in to the switched
socket. The switched socket should be in an easily accessible area within 900mm of the centre rear of the product.
Power requirements
Model Code Power Voltage Wattage Hz
EB60 6.1 A 220-240 V 1350 W 50-60 Hz
CONNECT THE COFFEE MAKER TO THE MAINS SUPPLY