Fisher & Paykel EB76PSX1 User manual

PROFESSIONAL
EB76PSX1 models
BUILT-IN COFFEE MAKER
INSTALLATION GUIDE
NZ AU
INSTALLATION GUIDE

3
SAFETY AND WARNINGS
IMPORTANT SAFETY INSTRUCTIONS!
Installation
WARNING!
Cut Hazard
Take care – some edges are sharp.
Failure to use caution could result in injury or cuts.
Checking for transport damage
After removing the packaging, make sure the product is complete and undamaged and that all
accessories are present. Do not use the appliance if it is visibly damaged. Contact Customer Care.
IMPORTANT!
● Installation must be performed by a qualified professional in compliance with legislation
in force in the country of installation.
● The packing elements (plastic bags, polystyrene foam, etc.) should be kept out of reach
of children.
● Never install the appliance in rooms where the temperature may drop to 0°C or lower.
● Customise the water hardness as soon as possible following the instructions in your
user guide.
● This appliance can be installed over a built-in oven if the latter is fitted with a cooling
fan at the rear (maximum microwave power: 3 kW).
● Connecting the appliance
● Danger! Check that the mains power supply voltage corresponds to the value indicated
on the rating plate on the bottom of the appliance.
● Connect the appliance to an efficiently earthed and correctly installed socket with a
minimum current rating of 10A only.
● Do not allow children and animals to stop or linger near the appliance when it is pulled
out of the cabinet.
● If the power socket does not match the plug on the appliance, have the socket replaced
with a suitable type by a qualified professional. To comply with safety directives, an
omnipolar switch with a minimum contact distance of 3 mm must be installed.
● Do not use multiple sockets or extensions.
● If the power socket does not match the plug on the appliance, have the socket replaced
with a suitable type by a qualified professional. To comply with safety directives, an
omnipolar switch with a minimum contact distance of 3 mm must be installed.
● Do not use multiple sockets or extensions.
● Safety cutout devices must be included in the mains power supply in compliance with
the installation regulations in the country concerned.
● This appliance conforms to EC Regulation 1935/2004 on materials and articles intended
to come into contact with food.
● Do not allow children and animals to stop or linger near the appliance when it is pulled
out of the cabinet-.
● Do not leave the machine pulled out of the cabinet when it is being used.
● Do not leave the machine pulled out of the cabinet when it is not needed.
● Install the machine according to the instructions in the handbook to guarantee there are
no spills when it is pulled out from the cabinet.
● The rails fixing panel must have a thickness suited to the fixing screws supplied standard.
● The panel material must be suited to the machine weight of approximately 25kg.
DISPOSAL
● The appliance must not be disposed of with household waste, but taken to an authorised
waste separation and recycling centre.
IMPORTANT!
SAVE THESE INSTRUCTIONS

4
Prior to installing your coffee maker, ensure the following:
zThe countertop and coffee maker cavity are square and level, and are the
required dimensions.
zThe installation will comply with all clearance requirements and applicable standards
and regulations.
zThe isolating switch will be easily accessible to the customer with the coffee
maker installed.
zThe electrician provides sufficient free length of power supply cable to reach from the
bottom rear of the cavity to at least 1.5m in front of the bottom edge of the opening.
zThe cable may enter the cavity from the side, top or bottom, but top entry must be at the
rear of the cavity.
zThe coffee maker connection socket (if fitted) is outside the cavity if the appliance is flush
to the rear wall.
zThe coffee maker will rest on a surface that can support its weight.
zThe height from the floor suits the customer.
zYou consult local building authorities and by-laws if in doubt regarding installation.
WARNING!
Some environmental factors and cooking habits can cause condensation in and around the
coffee maker during use. To protect surrounding cabinetry from possible damage caused by
frequent or excessive condensation, we recommend moisture-proofing the oven cavity.
During installation, please ensure the following:
zThe coffee maker can be used fully without obstruction.
zThe power supply cable does not touch any hot metal parts.
zThe isolating switch is easily accessible to the customer with the coffee maker installed.
zYou complete the ‘Final checklist’ at the end of the installation.
zIf, after following the instructions given, correct performance cannot be achieved, please
contact your nearest Fisher & Paykel Service Centre, Customer Care, or contact us through
our local website listed at the end of this document.
WARNING!
Take extra care not to damage the lower trim of the coffee maker during installation.
The trim is important for correct air circulation and allows the coffee maker to move
without obstruction.
The manufacturer does not accept any responsibility for damage resulting from
incorrect installation.
zThe coffee maker must be installed in a column and the column must be firmly fixed to the
wall with commercially available brackets.
zThe cabinet material must be able to withstand heat.
zTo guarantee correct ventilation, leave a gap in the cabinet according to the measurements
under cabinetry dimensions.
COMPONENTS REQUIREDINSTALLATION CONSIDERATIONS
zKeep all packing materials until the unit has been inspected.
zInspect the product to ensure there is no shipping damage. If any damage is detected
contact the dealer or retailer you bought the product from to report the damage.
zFisher & Paykel is not responsible for shipping damage.
Not supplied
Crosshead
screwdriver
Power drill Scissors
Supplied
Mounting screws
(28)
Spacers
(4 for side)
(4 for bottom)
Rails (2) Clip (1)
Side trims (2) Lower trim (1) Side/lower trim
screws (10)
3mm hex
key (1)
PRIOR TO INSTALLATION
DURING INSTALLATION
PARTS SUPPLIED
TOOLS REQUIRED

5
PRODUCT DIMENSIONS
FRONT
PLAN ISOMETRIC
PROFILE
PRODUCT DIMENSIONS
EB76 MODELS
MM
A Overall height 470
B Overall width 757
C Overall depth 484
D Height of chassis 442
E Width of chassis 560
F Depth of chassis 445
G Depth of coffee maker frame and
control panel 39
H Height of stepdown from top of control
panel to top of chassis 13
I Height of stepdown from bottom of chassis
to bottom of lower trim 15
Actual product dimensions may vary by ±2 mm.
F
A
E
C
G
H
I
D
b

6
FRONT ELEVATION
without front panels
DETAIL – PLAN VIEW
SIDE ELEVATION
with front panels
CABINETRY DIMENSIONS (FLUSH INSTALL)
CAVITY DIMENSIONS
EB76 MODELS
MM
A Minimum inside height of cavity and rebate 474
B Inside width between additional sidewalls* 560
C Minimum inside depth of cavity (from front of rebate) 560
D Minimum height between cabinetry front panels 474
E Overall width of cabinetry 762
F Minimum overall depth of cavity (incl. front panel) 600
G Rebate depth for flush install (incl. front panel) 39
H Overall height of spacer in base of cavity 16
I Ventilation gap 50
J Minimum clearance to adjacent cabinetry or other appliances 2
*Cabinetry requires additional vertical sidewalls to secure the product.
A D
B I
G
J
G
J
H
EC
F
Ventilation of 50x560mm or totalling
280cm2is required for companion
products. The air vent must be located
at the rear of cabinet, it can be
positioned at the base, top, sides, or
back of the cavity.
Additional sidewalls for
securing coffee maker
Sidewall of
appliance cabinet
Sidewall
of adjacent
cabinet
Front panel
of adjacent
cabinet
Built-in
Coffee Maker
Min
2mm
39mm
Critical rebate to
achieve flush finish
Additional
spacer

7
FRONT ELEVATION
without front panels
DETAIL – PLAN VIEW
SIDE ELEVATION
with front panels
A D
B G
H
H
F
EC
Ventilation of 50x560mm or totalling
280cm2is required for companion
products. The air vent must be located
at the rear of cabinet, it can be
positioned at the base, top, sides, or
back of the cavity.
Additional sidewalls for
securing coffee maker
Sidewall of
appliance cabinet
Sidewall
of adjacent
cabinet
Front panel
of adjacent
cabinet
Built-in
Coffee Maker
Min
2mm
Additional
spacer
CABINETRY DIMENSIONS (PROUD INSTALL)
CAVITY DIMENSIONS
EB76 MODELS
MM
A Minimum inside height of cavity 467
B Inside width between additional sidewalls* 560
C Minimum inside depth of cavity 560
D Minimum height between cabinetry front panels 474
E Overall width of cabinetry 762
F Overall height of spacer in base of cavity 16
G Ventilation gap 50
H Minimum clearance to adjacent cabinetry or other appliances 2
*Cabinetry requires additional vertical sidewalls to secure the product.

8
Before placing the coffee maker into the cavity:
zRoute the power cord into the back of the cavity and plug it in to the switched socket.
zThe switched socket should be in an easily accessible area within 900mm of the centre rear
of the product.
Note: All electrical work may only be carried out by suitably qualified and competent persons
in accordance with national and local safety regulations.
This coffee maker must be grounded.
Power requirements
POWER HZ VOLTAGE (V) PRESSURE
1350 W 50-60 Hz 220-240 V 1.5MPa
ATTACH THE TRIM TO THE COFFEE MAKERELECTRICAL CONNECTION
2
1
Before installing the coffee maker in the cabinetry, the side trims and lower trim need to
be attached.
Align the side trims on either side of
the coffee maker, using the locating
tabs and corresponding slots.
Attach the side trims using the hex
key and 6 of the screws provided.
Do not over-tighten.
3
Attach the 4 remaining screws to the
base of the side trims.
Only screw halfway in so the lower
trim can be mounted.
Slot the lower trim onto the screws,
using the locating slots.
Ensure the screws are seated as far
as possible into the the locating slots.
Pull the side trims forward so the
lower trim is flush with the back
edges.
Tighten the screws to secure.
4
1
2
1
2
3

9
SECURE THE COFFEE MAKER TO THE CABINETRY
2
1
Fix the power cable with the clip.
The power cable must be long
enough to allow the appliance to
be extracted from the cabinet to
fill the coffee bean container.
Position the rails on the sides of
the cabinet.
Fix with the screws provided,
then extract them completely.
zIf the coffee maker is installed
over a warmer drawer, use
the top surface of this as a
reference to position the rails.
zIn this case, there will be no
surface to rest the rails on.
5Use the levers at the front of
the rails to adjust the height of
the appliance.
If necessary, correct alignment of
the appliance by positioning the
spacers supplied under or at the
sides of the support.
4
min 560mm
3
Position the appliance on the
rails, making sure the pins
are correctly inserted in the
housings, then fix it with the
screws supplied.

10
INSTALLER CHECKLIST
TO BE COMPLETED BY THE INSTALLER
Turn the power to the coffee maker on. The display should turn on.
Fill the water tank to the indicated level.
Have you demonstrated basic operation to the customer?
Make sure the coffee maker is level and securely fitted to the cabinetry.
Check the lower trim is undamaged.
Check there is adequate clearance. This is to ensure correct air circulation.
Make sure any cable ties and internal packaging has been removed from the
coffee maker.
Make sure all vents and openings are clear and free of any obstruction or damage.
Failure to make sure all vents are clear may result in poor product performance.
Make sure the isolating switch is accessible to the customer.
Complete and keep for safe reference:
Model
Serial No.
Purchase Date
Purchaser
Dealer Address
Installer’s Name
Installer’s Signature
Installation Company
Installation Date

59284A 12.21
FISHERPAYKEL.COM
© Fisher & Paykel Appliances 2021. All rights reserved.
The models shown in this guide may not be available in all markets
and are subject to change at any time.
The product specifications in this guide apply to the specific products and
models described at the date of issue. Under our policy of continuous product
improvement, these specifications may change at any time.
For current details about model and specification availability in your country,
please go to our website or contact your local Fisher&Paykel dealer.